Buy wall mounted condensing boilers for maximum energy savings. Reliable performance, optimum efficiency and compact design. Choose from our selection of condensing boilers to heat your home efficiently and sustainably. Find out more today!
Wall mounted condensing boilers
Ferroli Ferroli Condensing Boiler Bluehelix Alpha 24c Complete With Methane Or LPG Fume Exhaust Kit Cod. 0tpf2awa
ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli condensing boiler Bluehelix Alpha 24C complete with methane or LPG fume exhaust kit cod. 0TPF2AWA Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating max / min heat input (Hs) kW 22.9 / 4.7 Max DHW heat input (Hi) kW 25 Max working pressure heating bar 3 Min. heating operating pressure bar 0.8 Heating expansion vessel capacity 8 litres Max DHW working pressure bar 9 Minimum DHW operating pressure bar 0.3 Sanitary flow rate ∆t 25°C l/min 14 Protection degree (IEC 60529) IP IPX4D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x250 Bluehelix Alpha .. More beautiful than "BEFORE" The new range of generators is equipped with the tested heat exchanger in stainless steel . Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX ALPHA is at the top of its category. TOP EFFICIENCY EVEN ON OLD SYSTEMS (REPLACEMENTS) mod. 24 C COMBINED (14 l/min at ∆t 25°C) The BLUEHELIX ALPHA thermal group exchanger (fig. A) compared with the more classic and widespread steel exchanger. This geometry allows the exchanger to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig. B tends to block up much faster in the part in contact with the flame due to the reduced passage area of the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values BLUEHELIX ALPHA FROM THE INSIDE EXCHANGER High flow single circuit stainless steel exchanger, resistant to clogging and easy to clean STEEL FRAME Made with high precision automated processes EXPANSION TANK 8 liter expansion tank placed on the side ELECTRIC PANEL FAN Offset fan, to facilitate maintenance of the primary exchanger without disassembly DOMESTIC HOT WATER EXCHANGER In stainless steel, with copper brazing CIRCULATOR High efficiency, for heating and exchange with the DHW circuit SEALED CHAMBER Removable steel panel to protect the combustion chamber with the function of a sealed chamber ELECTRICAL PANEL Large removable electrical panel to protect against any water damage that may occur during normal maintenance. Easy access to electrical connectors. THE ENGINE The tube that makes up the BLUEHELIX ALPHA exchanger is made of stainless steel, a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits. THE BOILER CONTROL The control box of BLUEHELIX ALPHA consists of an easy to use interface with backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. MC2 The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). MGR Methane, LPG, Propane Ready Air The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). Thanks to the new electronics supplied, the gas change operation is extremely simple. The MC2 combustion control performs constant monitoring of the quality of the combustion and by simply modifying a parameter on the electronic card (operation to be carried out only by qualified personnel) it is possible to operate the boiler on Natural Gas or LPG or Propane Air. It is therefore not necessary to purchase additional accessory kits. CONNECT New wireless remote control available as an accessory for home comfort management also from a smartphone using the connect app (iOS and Android). Maximizes room comfort with delivery temperature modulation through the Room Climatic Compensation (CCA) and External Climatic Compensation (CCE) functions via the external temperature detectable directly from the internet (or from an optional external probe). It improves the average seasonal efficiency in space heating by +4%. EASY MAINTENANCE Problem-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the BLUEHELIX ALPHA thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: - The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - Easy access to the burner unit by removing 4 screws and the quick coupling (clip) of the fan. - The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. - The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. - Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front SUN EASY FUNCTION BLUEHELIX ALPHA has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. By means of a sensor located on the DHW circuit, it continuously controls the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. STOP AND GO FUNCTION With the use of sanitary taps with mixing, short or very short dispensing for quick rinses involves the start of the boiler ignition procedure which usually ends immediately. The continuation of these "false starts" can, in the long run, compromise the average life of the product. For this reason BLUEHELIX ALPHA provides an electronic parameter through which it is possible to delay burner ignition (Stop and Go) by activating it only in the face of actual withdrawals of domestic hot water. OUTDOOR INSTALLATION - ANTIFREEZE FUNCTION To make the most of the available space, the new BLUEHELIX ALPHA 24 - 28 C boiler can be installed recessed into the wall thanks to the special kit; for more critical installations, in completely uncovered places not protected from atmospheric agents, the "painted cabinet" kit is also available. In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. SANITARY ECO-COMFORT FUNCTION In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable. The efficiency and the load profiles according to the ErP directive are at the top of the category: mod. 24 C / A - XL. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€653,00
-
BERETTA Condensing Boiler Beretta Ciao At 25 C Low Nox 20176935 Methane Complete With Smoke Kit
Beretta CIAO AT 25 C LOW NOx condensing boiler Complete with Fume Kit 20176935 - NEW Technical specifications according to ErP directives Class B heating energy efficiency Sanitary energy efficiency Class A Sanitary load profile - XL Technical features: Nominal heat input kW 25.00 NOx Class 6.00 Total electrical power Watt 102.00 IP electrical protection degree IPX5D Expansion vessel capacity 8 litres Maximum pressure bar 8 Quantity of hot water with Δt=25°C litres/min 14.3 Dimensions Boiler size (HxLxP) mm 715x405x250 CIAO AT with stainless steel heat exchanger BERETTA PRESENTS THE NEW CIAO AT, THE SPECIFIC CONDENSING BOILER FOR REPLACING TRADITIONAL HIGH TEMPERATURE SYSTEMS The new CIAO AT range is proposed in two combined models of 25 kW of power, with methane and LPG respectively. Both models are equipped with DIN standard hydraulic connections, to allow easy replacement of boilers with hydraulic standards other than Beretta. Many new features compared to the previous range. First of all, the new post-exchanger in stainless steel and composite material, which allows it to pre-heat the return water from the primary circuit using the residual heat of the exhaust fumes. The cooled burner, the new electronics and interface, the reduced depth of the boiler which allows installation even in contained recesses, complete the innovative profile of this product, which is preparing to become the reference in the specific segment of the replacement of radiator systems . The simple and linear design, in line with the Beretta style, the compactness of the dimensions and the installation flexibility make CIAO AT easy to integrate into any living environment, both inside homes and outdoors (in partially protected places) or recessed, also through dedicated accessories. The Technical Characteristics New layout with compact dimensions and low weight (only 31 kg!) to facilitate transport and built-in installation Traditional copper primary exchanger New and robust finned pack post-exchanger in stainless steel with taste and composite material Sanitary plate heat exchanger with possibility of pre-heating Innovative gas-air combustion supervision system Forced draft sealed chamber boiler with cooled low NOx burner Standard automatic by-pass Modulation range 1:3 Low consumption circulator (EEI ≤ 0.20), 6 m, with anti-blocking Standard analogue hydrometer Low NOx emissions : CLASS 6 (EN 15502-1) Innovative gas valve regulation procedure Sequence of DIN type hydraulic connections, ideal for replacing products with the same type of connections Maximum installation flexibility: Indoor, outdoor and recessed installation (in a partially protected place) Antifreeze heater kit, hydraulic connections and external probe available as accessories New flue flange with click fit connection: Fast and safe, without the need for an external collar IPX5D electrical protection degree Boiler support template supplied Compatible with BeSmart command Thermostat Dedicated LPG code: for conversion, contact authorized Beretta assistance centres LOW NOX BURNER CIAO AT is able to satisfy the most demanding requirements in terms of low emissions, in order to make heating appliances less polluting. Thanks to the innovative burner of CIAO AT, of the hyperstoichiometric type, a very low flame temperature is obtained as an effect. This characteristic, combined with the cooling of the burner through the heating circuit water, results in a significant lowering of the polluting values of carbon monoxide and nitrogen produced by combustion, such as to satisfy the new limits imposed by the legislation with flying colors ( EU Regulation 814/2013). NEW INTERFACE The new CIAO AT digital interface, designed with particular attention to ease of use, is equipped with a modern backlit display that allows immediate and complete reading of the information on the operating status of the machine, both for the user and for the installer or maintenance technician. Through six intuitively functional keys it is possible to easily adjust both the temperature in heating and DHW, and access the configuration of the machine parameters, rather than resetting the alarm states. UNIVERSAL INSTALLATION Ciao AT is designed to also be installed outdoors in partially protected places or contained recesses (e.g. Edilbox Beretta), thanks to the board's anti-freeze protection down to 0°C. In colder temperatures it is possible to extend the protection down to -10°C using the special antifreeze heater kit. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€674,00
-
VAILLANT Vaillant Ecotec Intro 28 Kw Vmw 24/28 As/1-1 Methane Low Nox Condensing Boiler Complete With Smoke Exhaust Kit - Erp
THE BOILER IS BORN WITH METHANE. THEREFORE, YOU MUST REQUEST THE TRANSFORMATION KIT. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Technical features Model : ecoTEC Intro VMW 24/28 AS/1-1 Article code : 0010026088 Power supply: methane Performance Heating power : 6.9 ~ 23.9 kW Nominal heat input in DHW : 6.9 ~ 28.0 kW Energy efficiency class in heating: A Sanitary energy efficiency class: A Sanitary load profile : XL NOx class : 6 Efficiency at 30% : 108.2% Domestic hot water production (ΔT = 30K): 13.4 l/min Domestic hot water temperature adjustment: 35°C ~ 60°C Modulation : 1:4 Expansion vessel pre-charge pressure: 0.75 bar Minimum water pressure: 0.3 bar Total electric power: 90 W Expansion vessel capacity: 8 litres Dimensions and weight Dimensions (HxWxD): 626x400x270 mm Weight : 25.6Kg Warranty extension to 7 years ecoTEC Intro VMW wall-mounted condensing boiler The most compact and lightest, now also for outdoor use The new ecoTEC intro VMW condensing boilers (for heating and domestic hot water production) are available in 24 and 28 kW power ratings, increasing the range of product choices within the consolidated range of Vaillant condensing boilers. In fact, this product gives new users the opportunity to approach the world of condensing boilers offered by Vaillant, without incurring excessive costs for replacing the old boiler. ecoTEC intro maintains the focus on energy saving by mounting a high-efficiency modulating pump that minimizes annual electricity consumption , with a consequent positive impact on bills. Also with regard to gas savings, Vaillant offers the new combustion technology , called fan push, where it is the fan which, thanks to the different levels of pressure exerted on the gas valve, guarantees the right ratio between combustion air and gas. The ecoTEC intro case is simple and essential, the dimensions appear to be extremely small which however do not affect or reduce the quality and efficiency of the product, guaranteed by Vaillant. The front panel introduces an innovative , extremely simple touch screen interface with 6 keys, black background display and 2 white digits with intermittent switching on. An additional e-bus connector has been added to the bottom of the boiler which allows connection to Vaillant temperature control units and thermostats. These wall mounted boilers are very simple to install thanks to their dimensions (62.6cm high, 40cm wide and 27cm deep) and low weight (about 26kg): these features make them ideal whenever replacement is required. All the components that are present in the product comply with the ErP energy efficiency regulations, a guideline also embraced by Vaillant, as a brand sensitive to environmental issues. This is all that the new ecoTEC intro can offer, in addition to a competitive price which does not affect performance. First ignition free Vaillant guarantees, through the work of its technicians, the free first ignition service on all wall-mounted condensing boilers. ecoTEC wall mounted boiler intro Electricity consumption in standby less than 2W Innovative touch screen display Sanitary comfort even with low flow rates Low installation costs Small size Exchanger in stainless steel Pneumatic combustion system with complete pre-mixing Vertical hydraulic connections 1:4 modulation Instant DHW production 8 liter expansion vessel Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€845,00
-
Riello Riello Start 25 Kis Low Nox Condensing Boiler Complete With Methane Fume Exhaust Kit 20187404
MURAL Riello START 25 Kis LOW NOx condensing boiler complete with methane fume exhaust kit 20187404 Seasonal space heating efficiency class A Water heating energy efficiency class- A Rated power P rated kW 19 Seasonal space heating energy efficiency % 93 HEATING Nominal heat input: kW 20.00 Nominal thermal power (80÷60 °C) kW 19.38 Nominal thermal power (50÷30 °C) kW 20.92 Reduced heat input: kW 3.10 Reduced thermal power (80÷60 °C) kW 2.94 Reduced thermal power (50÷30 °C) kW 3.04 SANITARY Nominal heat input kW 25.00 Nominal thermal power kW 25.00 Reduced heat input kW 3.10 Reduced thermal power (*) kW 3.10 YIELDS Useful efficiency Pn max-Pn min (80°-60°) % 96.9 - 94.7 Useful efficiency Pn max-Pn min (50°-30°) % 104.6 - 98.0 Useful efficiency 30 % (return 30°C) % 109.1 Efficiency at average P Range Rated (80°-60°) % - 97.0 Performance at average P Range Rated 30% (30th return) % - 109.3 Combustion efficiency % 97.2 Chimney losses with burner on (Pn max) % 2.8 Chimney losses with burner off % 0.09 Shell losses with burner on (Pn max) % 0.3 FUMES EXHAUST Nox class - UNI EN 15502: 6 Residual head concentric pipes 0.85 m ø 60-100 mm Pa : 60 Residual head separate pipes 0.5 m ø 80 mm Pa : 180 Boiler residual head without pipes and without flange Pa 186 ELECTRICAL CHARACTERISTICS Electric power (Pel max heating - Pel max san.) W 62 - 95 Circulator electric power (1000 l/h) W 42 Supply voltage V - Hz 230-50 IP X5D degree of protection HEATING EXERCISE Maximum pressure bar 3 Minimum pressure for standard operation 0.25 bar Maximum temperature 90 °C Pump: max head available to the system mbar 408 at a flow rate of 1000 l/h Membrane expansion tank l 8 Expansion tank preload bar 1 HEALTHCARE EXERCISE - INSTANT VERSION Maximum pressure bar - 8 Minimum pressure bar - 0.5 Quantity of hot water at ?t 25°C l/min - 14.3 with ?t 30°C l/min - 11.9 with ?t 35°C l/min - 10.2 Minimum domestic water flow rate l/min - 2 Sanitary H2O temperature selection field. °C - 37/60 Flow regulator l/min – 10 New Start START is the new proposal, completely renewed from a technological and functional point of view, of Riello condensing boilers for small and medium-sized domestic users. START is available in 3 sizes 15, 25, 30 kW, in combined (KIS) and heating only (IS) versions. One of the distinctive features of the new START is the innovative digital control panel with touch keys designed with particular attention to ease of use. High efficiency sanitary exchanger developed by Riello Modern and intuitive touchscreen HMI, with representative icons and capacitive keys with acoustic "buzzer" sound Modern and linear design with under-boiler connection cover available as an accessory for excellent aesthetic integration Specific DHW electronic functions: DHW delay, anti-short cycle function and smart fan Hydraulic unit with DIN standard sequence Low consumption circulator (IEE?0.20) 7 m with high head available as an accessory Ease of installation, integration even in confined spaces and replacement thanks to the wide choice of accessories available as optionals Modulation ratio 1:8 Easy maintenance and cleaning of the combustion chamber thanks to the front access to the exchanger – Seasonal efficiency 93% 8-litre side expansion tank Standard flue gas flange with dedicated flue system Standard thermoregulation in combination with the external probe, available as an accessory Possibility of recessed installation (model 25 KIS and 30 KIS) and outdoors in partially protected places (IPX5D) Assembly crosspiece already integrated in the boiler and power supply cable supplied Natural gas operation as standard with the possibility of conversion to LPG (G31) and propane air using accessories. This modification is the responsibility of the installer or the technical assistance service. IPX5D electrical protection degree. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€809,00
-
BAXI Caldaia Baxi Duo-Tec Compact E 24 kW a condensazione low NOx completa di kit scarico fumi Metano o Gpl - Novità
ATTENZIONE LA CALDAIA VIENE FORNITA A METANO. FUNZIONAMENTO A GPL TRAMITE REGOLAZIONE DA PARTE DEL CENTRO ASSISTENZA AUTORIZZATO. PER INFO, CONTATTARE PREVENTIVAMENTE L'ASSISTENZA BAXI Caldaia Baxi Duo-Tec Compact E 24 kW a condensazione low NOx completa di kit scarico fumi Metano o Gpl - NovitàCaratteristiche Tecniche Classe di efficienza energetica ErP (risc e ACS): A Profilo di carico: XL Portata termica nominale sanitario kW 24,7 Portata termica nominale riscaldamento kW 20,6 Efficienza energetica stagionale del riscaldamento d'ambiente ŋs % 93 Emissioni di ossidi di azoto NOx mg/kWh 15 Temperatura minima di funzionamento °C -5 Capacità vaso espansione l 7 Regolazione temperatura acqua circuito riscaldamento °C 25-80 Produzione acqua sanitaria ∆T 25°C (1) l/min 13,8 Portata minima acqua circuito sanitario l/min 2 Dimensioni (hxlxp) mm 700x400x299 Grado di protezione IPX5D Gamma DUO-TEC COMPACT E Nuovo design: cambia l’estetica, non le prestazioni. Luna Duo-tec E e Duo-tec Compact E: le già note caldaie Baxi si presentano oggi con una nuova estetica, sempre più moderna ed attenta alle nuove tendenze di design, che ne consente l’inserimento in qualsiasi contesto abitativo. Anche il pannello comandi è stato completamente rinnovato ed è dotato di un nuovo display LCD retroilluminato ancora più chiaro e semplice da usare grazie a tasti dedicati ed indipendenti. Le nuove caldaie, ancora più belle e moderne grazie al restyling, mantengono comunque intatte le caratteristiche che da sempre hanno contraddistinto la gamma Duo-tec: Affidabilità. Robustezza, durabilità e affidabilità nelle prestazioni; Efficienza e risparmio. La riduzione dei cicli di accensione/spegnimento si traduce in notevoli benefici in termini di risparmio energetico e minori emissioni; Completezza di gamma. Modelli solo riscaldamento, con produzione istantanea ACS, e anche la versione compatta con possibilità di installazione all’esterno. La gamma si è ulteriormente arricchita con i nuovi modelli dotati DI SERIE del cronotermostato modulante con wi-fi integrato Baxi MagoLa caldaia ideale per nuove costruzioni e per la sostituzione La gamma di caldaie a gas a condensazione Duo-tec E è stata specificatamente progettata rispettando i requisiti delle Direttive Ecodesign e Labelling, per renderla particolarmente adatta sia in caso di nuove costruzioni sia in sostituzione di un vecchio generatore. La classe energetica, identificata da una lettera, esprime un intervallo di valori di efficienza entro il quale risiede quello espresso dal prodotto in esame. L’etichetta nasce per il consumatore finale, in modo che, attraverso dati veri e comparabili, possa fare scelte consapevoli indirizzandosi su prodotti ad alta efficienza.Funzione preriscaldo scambiatoreLe caldaie della gamma Duo-tec E sono dotate della funzione di preriscaldo dello scambiatore che garantisce la produzione immediata di acqua calda sanitaria alla temperatura comfort impostata. Infatti, l’acqua sanitaria passando attraverso le piastre dello scambiatore preriscaldato, viene erogata già alla temperatura desiderata senza tempi di attesa. La funzione può essere facilmente attivata/disattivata da un apposito parametro della caldaiaInfo caldaiaPremendo il tasto dedicato , è possibile visualizzare numerose informazioni in merito al funzionamento della caldaia come ad esempio: pressione acqua impianto riscaldamento (trasduttore di pressione elettronico presente nel gruppo idraulico); temperatura di mandata/ritorno riscaldamento; temperatura esterna (con sonda esterna installata); temperatura acqua calda sanitaria.Efficienza e risparmio maggiore efficienza data da minori accensioni e spegnimenti: con un rapporto di modulazione elevato, la riduzione dei continui cicli di accensione/spegnimento comporta una significativa riduzione dei consumi (dell’8-10%) e una pari riduzione delle emissioni inquinanti; adeguamento della potenza termica prodotta alla potenza dissipata evitando quindi un eccessivo surriscaldamento/raffrescamento dei locali. Gas Adaptive ControlÈ un innovativo sistema che, grazie ad una nuova elettronica di controllo e ad una nuova valvola a gas elettronica, garantisce un controllo automatico della combustione per mantenere costantemente i valori di massima efficienza.Vantaggi: non ci sono interventi manuali - ridotte misurazioni, tarature o cambio ugelli con questo sistema, la caldaia si auto adatta alla qualità del gas e alla lunghezza dei tubi di scarico fumi mantenendo costante il rendimento la caldaia inoltre si autoregola costantemente per mantenere i valori di massima efficienza favorendo una riduzione dei consumi di gas e generando meno inquinamento grazie al continuo controllo delle emissioni Installazione all’esterno Le caldaie Duo-tec Compact E possono essere installate all’esterno in luoghi parzialmente protetti grazie al nuovo kit di copertura superiore e al kit di chiusura inferiore (disponibili come accessori). La gamma Duo-tec Compact E, infatti, è dotata DI SERIE di un sistema antigelo elettronico che garantisce il funzionamento fino alla temperatura di -5 °C: la protezione IPX5D, inoltre, tutela le parti elettriche da getti d’acqua che possono provenire da tutte le direzioni. Nuovo design moderno ed elegante per tutta la gamma Ampio campo di modulazione 1:7 maggiore efficienza e silenziosità GAC (gas adaptive control): controllo automatico della combustione Pannello comandi digitale con ampio display LCD retroilluminato Nuovo kit di copertura: possibilità di installazione all’esterno in luoghi parzialmente protetti (accessorio a richiesta) Allacciamento tubo di scarico Ø50 mm rigido e flessibile: soluzione per risanamento canne fumarie - per il mod. 24 kW lunghezza totale 40 metri (aspirazione+scarico) Dimensioni compatte: 700x400x299 mm Sistema idraulico Valvola deviatrice a tre vie elettrica Bruciatore a premiscelazione in acciaio inox Scambiatore acqua/fumi in acciaio inox Scambiatore sanitario maggiorato in acciaio inox che permette alla caldaia di condensare anche in funzionamento sanitario Ventilatore modulante a variazione elettronica di velocità By-pass automatico Pompa di circolazione ad alta efficienza a modulazione totale Sistema antibloccaggio pompa e valvola a tre vie che interviene ogni 24 ore Valvola di sicurezza circuito riscaldamento a 3 bar Sistema di termoregolazione Regolazione climatica di serie (con sonda esterna disponibile come optional) Predisposizione per il collegamento ad un impianto a zone Sistema di controllo Termostato di sicurezza contro le sovratemperature dello scambiatore acqua/fumi Pressostato idraulico che blocca il gas in caso di mancanza d’acqua Sonda NTC di sicurezza contro le sovratemperature dei fumi Controllo temperature mediante sonde NTC Dispositivo antigelo totale Termometro elettronico Manometro circuito riscaldamento Garanzia Prodotto : Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.
€680,00
-
Ferroli Ferroli Divacondens D Plus F24 Low Nox LPG Condensing Boiler Complete With Smoke Exhaust Kit
LPG operation with the use of a special conversion kit to be requested from the Authorized Assistance Centre, we recommend contacting the local assistance center before purchasing Technical features Model : Divacondens D Plus F24 Power supply: LPG Energy efficiency Heating energy efficiency class: B Sanitary energy efficiency class: A ACS profile : XL Performance Heat output : 7.5 ~ 25.0 kW Thermal power 80°C ~ 60°C : 7.2 ~ 24.2 kW Thermal power 50°C ~ 30°C : 7.7 ~ 26.2 kW Useful thermal efficiency 80°C ~ 60°C : 96.0% ~ 96.9% Useful thermal efficiency 50°C ~ 30°C : 102.4~ 104.0% NOx emissions : 6 Maximum production of domestic hot water Δt 25°C : 13.9 l/min Maximum production of domestic hot water Δt 30°C : 11.6 l/min Heating working pressure: 0.8 ~ 3 bar Sanitary operating pressure: 9 bar Dimensions and weight Dimensions (LxHxP): 400x680x330 mm Empty weight: 35.0 kg 5 years without worries Extension of the manufacturer's standard warranty to 5 YEARS on Ferroli brand gas condensing boilers of less than 35 kW in the DIVACONDENS and BLUEHELIX series through the local authorized Ferroli technical assistance centre. Wall-mounted boiler Ferroli DIVACONDENS D PLUS Atmospheric wall-mounted condensing boilers, with instantaneous domestic hot water production The simplest solution for a condensing boiler DIVACONDENS D PLUS is the condensing heat generator for traditional heating systems. The tried and tested Ferroli technology in the field of traditional wall mounted boilers has been enriched by increasing the performance of the product in the simplest way, with the use of a robust recuperator which preheats the primary circuit using the residual heat of the exhaust fumes and a new cooled burner with low NOx emissions. DIVACONDENS D PLUS is offered in a single model for heating and instantaneous production of domestic hot water Product plus > Condensing boiler for heating high temperature systems and producing domestic hot water. It is not suitable for combination with direct delivery to systems with low temperature radiant panels > Compact geometry primary exchanger > Instant production of domestic hot water with dedicated plate exchanger > Post-recovery of the latent heat of condensation, in function of pre-heating of the primary circuit > Forced draught sealed chamber boiler, with water-cooled atmospheric burner with low NOx emissions > Standard automatic hydraulic by-pass > Minimum polluting emissions, class 6 according to EN 15502-1 > High-efficiency, low-consumption circulator with anti-blocking system by activation for a few seconds every 24 hours of inactivity > Can be combined with the modulating remote timer control > Simple and complete control panel, display user interface, with setting keys > Robust post-condenser fed by the closed circuit of the primary. The heat exchange with the fumes takes place inside large diameter water passages > Generator with simple and rational operation > ECO function in DHW for greater savings in the period of low use of hot water > Predisposition for solar systems : prearranged for the production of domestic hot water combined with solar panel systems > Place of installation : also for outdoors in a partially protected place down to -5°C as standard > Certified operation also with propane air (50% air - 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center > Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre Boiler control The DIVACONDENS D PLUS control unit consists of an easy-to-use interface with a backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. Main components Heat recovery Post-condenser with recovery of latent heat from the combustion fumes and condensate discharge Steel frame Made with high precision automated processes. Incorporates an 8 liter expansion vessel Central heating primary exchanger protected by a non-toxic aluminum coating Low NOx burner Water-cooled low temperature micro flame type. Minimum NOx emissions High efficiency circulator , for heating and exchange with the DHW circuit Domestic hot water exchanger In stainless steel, with copper brazing ECS - Evolved Combustion System Innovative combustion control that guarantees optimal functioning under various thermal load conditions and types of chimney Optimize comfort and savings "ROMEO N" timer control The ROMEO N timer control allows control and setting of the boiler functions directly from the room in which it is installed. Comfort programming is possible on a weekly basis and also includes the 'holiday' function. ROMEO N is available with wired or wireless connection. With ROMEO N you can: Adjust the heating and DHW temperatures Know the operating status of the boiler View the indoor temperature in your home Program the weekly ambient comfort Activating/deactivating the heating function via the telephone (Optional) Smart CONNECT remote control Remote control supplied with the class A+ kit code for home comfort management also from a Smartphone Possibility of managing up to 8 zones using additional room units Connection to the home Wi-Fi network via the supplied RF/Wi-Fi receiver CONNECT APP available for boiler on/off and domestic heating/DHW comfort management remotely via Smartphone (iOS and Android) Maximization of room comfort with modulating regulation of the flow temperature through the Room Climatic Compensation functions differentiated for each zone and External Climatic Compensation via external temperature detectable directly from the internet or from an optional external probe It improves the average seasonal efficiency in space heating by +4%. Weekly time programming in 30-minute intervals via APP CONNECT Operating modes : Off, Holiday, Automatic, Manual Three modifiable temperature levels : Comfort, Economy, Antifreeze By reading the external temperature directly from the internet (or from the optional external probe) the system is able to vary the system temperature according to the external temperature measured on the basis of configurable climatic curves, thus guaranteeing the user maximum room comfort at the change in external climatic conditions. The modulating function of CONNECT allows modulation of the boiler power as the set room temperature value is reached. This improves the quality of comfort by eliminating heat peaks with consequent energy savings Solar circuit integration Sun Easy function DIVACONDENS D PLUS boasts electronics that simplify integration with thermal solar systems, both with natural and forced circulation. The microprocessor controls the temperature of the water coming from the solar circuit through the domestic hot water sensor and turns on the burner only if necessary. In case of insufficient irradiation and therefore a modest pre-heating of the domestic water, the boiler will contribute with the heat necessary to reach the required set point temperature. If the sun and the solar system fulfill their "duty" no integration by the boiler will be necessary, the hot water will be conveyed to the tap, without the need for additional devices, with the mixing of the thermostatic valves. To reach the desired temperature, SUN EASY allows considerable savings even during the coldest seasons, exploiting and integrating even the smallest solar contribution, otherwise lost. Safety and comfort Functions Antifreeze In the event that the temperature in the boiler drops to 5°C, the burner ignites automatically and the circulator is activated in order to protect the appliance from damage caused by freezing. This function is active with the boiler powered by the gas circuit and under electrical voltage Post-circulation This function makes it possible to recover all the heat supplied by thermal inertia of the exchanger and transfer it to the heating system, and consequently to the rooms to be heated. This is a timer function and is active after the burner goes out in heating mode. Sliding temperature operation With the installation of the “External probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user Easy Control The electronic board of DIVACONDENS D PLUS adopts the Opentherm protocol. It allows the integration of other peripheral control units such as, for example, the ROMEO N and CONNECT remote timer controls. In fact, the Opentherm standard has been specially designed to share the logic and operating algorithms of the boiler with other additional control units. As a digital protocol, it allows total integration between the boiler and the satellite, with full control of the functions from the boiler and similarly from its satellite Product Guarantee : All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€580,00
-
Ariston Ariston Hs Premium 30 Eu Condensing Boiler Complete With Methane Fume Exhaust Kit -Erp
ARISTON HS PREMIUM 30 EU CONDENSING BOILER COMPLETE WITH METHANE FUME EXHAUST KIT - ErP Technical features Product code: 3300760 Energy label specifications according to the European ErP directive Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal heat input in heating max/min: Kw 29.0/6.0 Max/min nominal heat input in domestic hot water: Kw 29.0/6.0 Useful thermal power in heating: max/min: Kw 28.4/5.8 Efficiency at nominal heat input (60/80°C): 97.8% Efficiency at nominal heat input (30/50°C): 104.0% Efficiency at 30% at 30°C: 108.0% Max/min heating temperature (high temperatures): 82/35°C Max/min heating temperature (low temp.): 45/25°C Max/min DHW temperature: 60/36 °C Sanitary water production (DT=25°C): lt./min. 16.3 Specific flow rate (first 10' with DT=30°C): lt./min. 11.6 Total absorbed electric power W 82 Degrees of protection of the electrical system IP X5D Dimensions (HxWxD) mm 745 x 400 x 319 Power supply: METHANE Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. HS Premium Performance ★★★★ NOx class 5 LCD display. Continuous modulation high efficiency circulator. Modulation ratio 1:4. Arrangement for integration with system configuration through the new Buss Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation (with Sensys). Arrangement for solar system management. Aluminum alloy primary exchanger Sanitary plate heat exchanger. Self-diagnosis system by codes. Increased expansion tank lt.8. Cold water inlet and heating return filters. Protection against freezing, limescale and circulator blocking. Operation only with methane gas Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€820,00
-
BAXI Baxi Luna Classic 28 Kw Condensing Low Nox Boiler Complete With Methane Or LPG Fume Exhaust Kit New Wi-Fi Optional
ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Baxi Luna Classic 28 kW low NOx condensing boiler complete with methane or LPG fume exhaust kit New optional Wi-Fi Technical features Sanitary nominal thermal power kW 28.9 Heating rated thermal power kW 24.7 Useful thermal power at thermal power nom. and high temp. regime* P4 kW 24 XL load profile Seasonal space heating energy efficiency class A Water heating energy efficiency class A Seasonal space heating energy efficiency ?s % 94 Minimum operating temperature °C -5 Heating expansion vessel capacity l 7 Sanitary water production ?T 25°C (1) l/min 16.1 Dimensions (hxwxd) mm 700 x 395 x 285; 30 Degree of protection IPX5D CLASSIC MOON The new Luna Classic is the ideal product for apartments or small houses. Its compact dimensions (700x395x285 mm) ne allow installation in confined spaces such as kitchen wall units or in the laundry room. Excellent value for money, simple and intuitive management. The heart of the Luna Classic is the new electronic platform: this revolutionary system replaces the functions of the historical Luna models, raising the quality of the product to a new level. Great attention has been paid to meeting the needs of the end user. System customization and optimization are possible without compromising ease of use. The Luna Classic range includes 2 models for heating and the instantaneous production of domestic hot water, Luna Classic 24 and Luna Classic 28 User Interface Luna Classic Control Panel Renewed interface with: Backlit menu with icons; Simple settings to adjust the heating and domestic hot water temperature via two dedicated knobs; 4 buttons with dedicated functions: menu, confirm, back and reset. 2 functions for perfect water temperature Domestic hot water management can be enhanced and improved by activating two dedicated functions: relaxation function It is a pre-heating function which keeps the domestic hot water at the desired temperature for a pre-set period of time, or for 30 minutes after selecting the chosen temperature. Boost function Activates the boiler at maximum power for faster delivery of hot water. Baxi MaGO Luna Classic can be connected directly to the Baxi Mago, the modulating chronothermostat with integrated wi-fi that allows you to manage home comfort directly from an App. By downloading the dedicated App onto your smartphone, it will be possible to connect to one or more homes to control the temperature, manage the programming, display the consumption graph, read any messages error, set vacation mode, etc. The combination of the boiler with the Baxi Mago A+ kit increases its energy efficiency, raising it to class A+ Specifications: Operation with a mixture composed of up to 20% hydrogen New single coil stainless steel heat exchanger, featuring sections with large water passages for greater seasonal thermal efficiency Seasonal energy efficiency of 94% thanks to the advanced technology applied Renewed interface with backlit display Easy replacement of conventional boilers thanks to central flue gas outlet Modulation range 1:5 greater efficiency and silence Ø80 double exhaust STANDARD Connection to Ø50 mm rigid and flexible waste pipe: solutions for the rehabilitation of flues total length (exhaust + intake) 40 meters Connection to pressurized collective flues Boilers running on methane that can be converted to LPG and propane by means of a specific regulation (conversion kit not necessary) Compact dimensions: 700x395x285 mm Class A+ for Luna Classic 24/28 models with Baxi Mago and external probe (as accessories) New hydraulic group that guarantees maximum levels of performance and durability over time Optimal insulation for silent operation Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€794,00 - €833,00
-
Ariston Ariston Cares S 24 Eu Condensing Boiler Complete With Methane Or LPG Fume Exhaust Kit Low Nox 3301637 - New
ATTENTION THE BOILER IS BORN WITH METHANE. THEREFORE, THE STANDARD TRANSFORMATION KIT WILL BE SUPPLIED. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Ariston CARES S 24 EU condensing boiler complete with methane or low NOx LPG fume exhaust kit 3301637 - NEW Heating energy class A Sanitary energy class A XL load profile Nominal heat input max min heating 20.0/4.7 kW Nominal max min DHW heat input 23.5/4.7 kW Heating temperature max min 82 / 35 °C Quantity of hot water deltaT=25°C 13.2 litres/min Power frequency voltage 230/50 V/Hz Electrical protection degree X5D IP NOx class 6 CARES S The condensing boiler suitable for every need, able to combine great performance and high robustness. Thanks to the stainless steel condensing exchanger, CARES S represents the right balance between comfort and performance. Reduction of energy consumption up to 35% Stainless steel condensing exchanger More robust design thanks to the new metal front panel Better accessibility thanks to the front hydrometer MADE IN ITALY produced entirely in Italy SMALL SIZE small footprint for easy installation SYSTEM MANAGEMENT new communication protocol set up to guarantee complete management of the system. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€737,00€715,00
-
Ferroli Offer - Ferroli Bluehelix Pro Rrt 28 C Natural Gas Or LPG Low Nox 0t3b2iwa Condensing Boiler Complete With Smoke Exhaust Kit
ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli BLUEHELIX PRO RRT 28 C methane or LPG condensing boiler Complete with Lox NOx Fume Exhaust Kit - NEW Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Thermal power 80°C-60°C Max Heating: 24.0 / 4.9 kW Thermal power 50°C-30°C Max Sanitary: 26.0 / 5.4 kw Useful thermal efficiency 30%: 109.7 Max working pressure heating bar 3 NOx class 6 Sanitary flow rate ∆t 25°C 15.8 Protection degree (IEC 60529) IP X5D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x250 BLUEHELIX PRO RRT The quality of the BLUEHELIX line is unquestionable, and Ferroli is ready to put it to the test by offering its customers extended warranty coverage which also ensures periodic maintenance and statutory checks > STRONG POINTS: - With attention to aesthetics and silence, it continues the tradition of appreciation of the previous "Bluehelix Pro" series - DUAL STAINLESS STEEL exchanger : boiler with primary exchanger for heating and domestic hot water in very thick stainless steel integrated in a single component (DUAL). High efficiency even during DHW operation (94%). - Increased hydraulic passages of the exchanger both on the heating circuit and on the DHW circuit. - : in combination with the modulating remote control and the external probe (optional) it reaches the upper efficiency class A+ (scale from G to A+++) - MC2 : Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) - MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits - Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace - Hydraulic connections covered by the boiler casing - Large backlit multifunction graphic display for easy and correct setting of the parameters - Standard by-pass > BENEFITS OF bluehelix PRO RRT C: - Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes - FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard - Designed to simplify and facilitate normal maintenance and cleaning operations - Predisposition for solar systems: prearranged for the production of domestic hot water combined with solar panel systems - STOP AND GO: it is possible to delay the ignition of the burner by activating it only in the face of real withdrawals of domestic hot water - 3-star certified comfort in sanitary manufacturing according to EN 13203 - Minimum polluting emissions (class 6 according to EN 15502-1) - Sliding temperature operation via optional external probe - Low consumption modulating heating pump (ErP Ready - Class A) - Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) - Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit - Free methane/LPG/propaneted air transformation when checking the product and activating the warranty, to be requested from the Authorized Assistance Center Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€780,00€760,00
-
DAIKIN Daikin D2cnd024 Condensing Boiler From 24 Kw Methane Complete With Fume Exhaust Kit
ATTENTION ! In case of immediate lack of availability, the product will be ordered and shipped within 10 working days Technical features Model: D2CND024A0AA Heating Efficiency class (55°C) : A Fireplace power (Qn) : 2.9 - 23.5 kW Nominal heating power (80°/60 °C): 2.8 - 22.8 kW Nominal heating power (50ç/30 °C) : 3.1 - 24.0 kW Heating efficiency : Up to 108.7% Modulation range : 1:8 Expansion vessel volume: 8 litres Domestic hot water Efficiency class : A Withdrawal profile : XL Temperature range : 35°C ~ 60°C Withdrawal in continuous service (∆T=30°C): 11.3 l/min Withdrawal in continuous service (∆T=25°C): 13.6 l/min Pressure of the water network: 0.5 ~ 10 Bar Technical data Power supply (V,Hz, Ø) : 220~240/50/1 Electric Power Input: 3.5~86W Water content : 1.31 litres Sound power : 39 dB(A) Sound pressure : 49 dB(A) NOx class : 6 Exhaust gas temperature (G20) : 77° C Electrical protection class : IP X5D Installation data Flue diameter: 60/100 mm Maximum length for flue system DN 60/100 : 12.5 m Maximum length for flue system DN 80/125 : 42.8 m Maximum length for flue system DN 80/80 : 125 m Dimensions and weight Dimensions (HxLxD): 590x400x256 mm Weight : 27Kg Simply Serene Guarantee To guarantee you maximum serenity, DAIKIN has studied "SIMPLY SERENIOUS", an extension of the guarantee up to the 5th year of life of your product, which provides for the subscription of a Scheduled Maintenance Plan with specialized Daikin technicians Ultra-compact Daikin D2C condensing boilers for heating and DHW production Why choose a condensing boiler? Daikin condensing boilers are a good solution for those wishing to replace an existing boiler with a more efficient alternative, saving on costs. Our portfolio includes boilers for every need, from the D2C and Full condens and Full Condens TOP wall-hung boilers, to the GCU boiler with built-in thermal storage, to the A2 floor-standing diesel boiler Thanks to the special Daikin-patented exchanger, the D2CND boiler obtains high specific power and high partialization to guarantee comfort and efficiency in any operating mode and in minimum encumbrance. The D2T version, heating only, integrates a diverter valve and can be connected directly to a storage tank for the production of domestic hot water. Ultra-compact and elegant technology The beautifully compact boiler The new D2C condensing boilers are 100% Daikin design. The ultra-compact dimensions make them suitable for even the smallest apartments, where every centimeter saved is space gained A boiler for every need D2C boilers are available in 3 combi versions 24, 28 and 35 kW for heating and instant domestic hot water production. A wide range of heating-only boilers is also available, the D2T, in 5 sizes, from 12 to 35 kW, which can be combined with a storage tank for the production of domestic hot water. You can install them virtually anywhere thanks to their compact size and minimal installation space required. Thanks to the IPX5D degree of electrical protection and the antifreeze kit, they can also be installed outdoors. Do you want to have your heating system under control even when you are not at home? Pair the Lan Adapter to control via APP ! Efficiency and respect for the environment The combustion system with regulation via Lambda Gx probe automatically adapts to the quality of the gas used, methane or LPG, always guaranteeing clean combustion and minimum polluting emissions . Maximum comfort Thanks to a high modulation ratio, up to 1:8 , the output power is automatically varied to always adapt, instant by instant, to the real need of the house in which it is installed. Endless showers? Domestic hot water will no longer be a problem with the D2C boiler with a DHW flow rate of up to 19 l/min in the 35 kW version Cutting-edge technology combines with an attractive and user-friendly user interface Daikin Eye An elegant luminous eye which, thanks to a multi-chromatic LED, signals the operating status of the appliance. In the event of a fault, the LED turns red and the error code is displayed. The easiest way to interact with your boiler! Daikin Heating Online Controller The heating system is always under control, wherever you are! Thanks to the Daikin Heating Online Controller application you can now control and monitor your boiler from the comfort of your smartphone in a simple and intuitive way Monitor The status of your heating system The ambient temperature in your home Energy consumption graphs. Plan The temperature of your home and the operation of the boiler with up to 6 actions per day for 7 days Vacation mode Check it out The operating mode and the set room temperature The system and the production of domestic hot water By integrating third-party products and services through IFTTT services (if this then that) Changing your old boiler has never been easier! Thanks to its small size and IPX5D degree of protection, Daikin D2C can be installed practically anywhere. Its ultra-compact dimensions make it suitable for even the smallest apartments, where every centimeter saved is space gained and its elegant shapes look good in the kitchen. A distinctive element of the 100% Daikin design is also the Daikin Eye: an elegant luminous eye which, thanks to a multi-chromatic LED, signals the operating status of the appliance. Daikin D2C contains the best of condensing technology. The SCOT combustion regulation system automatically adapts to the quality of the gas used, methane or LPG, always guaranteeing clean combustion and minimum polluting emissions. Dimensions and weight reduced to a minimum are possible thanks to the innovative Daikin patented high specific capacity air/fume exchanger body. Heart of the new D2C boiler, it has been designed to obtain the highest thermal power in the smallest size. Functions Eco Mode Return temperature control to optimize condensation Warm start DHW exchanger already heated and ready for use thanks to the memorization of the habits which allows to anticipate the request for domestic hot water Solar connection If the water entering the boiler has been preheated by the solar system, the burner does not ignite, for optimal integration of the solar source Exclusive initiative for Daikin customers On the occasion of the launch of the new Daikin D2C, starting from 1 March 2017 Daikin is giving away the activation cost of Simply Serene. The offer is valid for all those who will purchase a Daikin boiler of any type and who already own a Daikin mono split or multisplit. All the details on daikin.it. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€995,00
-
HERMANN SAUNIER DUVAL Hermann Saunier Duval Condensing Boiler Themis Condens 24 Kw Low Nox Methane Complete With Fume Exhaust Kit Cod. 0010028067 - New
Hermann Saunier Duval Condensing Boiler THEMIS CONDENS 24 kW low NOx Methane Complete with Smoke Exhaust Kit cod. 0010028067 - NEWS ErP - Energy class Heating efficiency class B Sanitary efficiency class A Sanitary load profile XL CE identification number PIN CE 0476CQ0908 Heating Fireplace flow rate Qmin/max - 80/60°C kW 13.0/24.0 Rated power Pmin/max - 80/60°C kW 12.5/23.04 Rated power Pmin/max - 50/30°C kW - Efficiency Pmax - 80/60°C - 50/30°C % 96.0 / - Efficiency P30% - 40/30°C % 99.7 Cloak losses - Bruc. On - 80/60°C Pmax/Pmin % 0.1/2.3 Chimney losses - Bruc. On - 80/60°C Pmax/Pmin % 2.2/1.9 Chimney losses - Bruc. Off - heating/DHW % 0.3/0.7 Min/max delivery temperature °C 30/85 Boiler operating pressure min/max bar 0.3/3 Heating expansion vessel - Capacity/preload l/bar 7/0.75 Sanitary Domestic hot water production type Instantaneous ACS quality classification (EN 13203-1) 2 stars Capacity at the hearth min/max - 60°C kW 13.0/24.0 Rated power min/max - 60°C kW 12.3/23.2 Continuous flow rate (∆T= 25K) l/m 13.8 Specific flow rate (∆T = 30K) (EN13203) l/m 11.4 Peak flow rate in 10 minutes (∆T = 30K) l/10 min 114 DHW temperature min/max °C 35/65 DHW storage heat loss kWh/24h - Min/max supply pressure bar -/8 generals Gas category II2H Supply pressure mbar 20 Heating gas flow Pmin/Pmax m3/h 2.66 DHW gas flow rate Pmax m3/h 2.66 Voltage/frequency/intensity V/Hz/A 230/50/0.66 Absorption - Peak/Pmax/Pmin/Stand-by W - / - / 60 / - Heating flue temp. (50-30°C) Pmin °C 51 Sanitary fume temp. (DHW T=50°C) Pmax °C 68 Flue gas heating Pmin/Pmax g/s - CO2 Pmax % 7 Weighted NOx (0% O2) mg/kWh 56.0 Residual head at the fan Pa - IPX 4D electrical protection Weight kg 38 Dimensions 70 cm high, 40 wide and 29.5 deep (24 kW) THEMIS CONDENS Low NOx - NEW Wall-mounted condensing boiler for heating and domestic hot water, for high temperature systems. The new Themis Condens Low NOx is the condensing solution developed by Hermann Saunier Duval to replace traditional wall-mounted boilers combined with radiators that require high inlet temperature values. The main novelty is the low NOx emission burner (class 6) which makes it possible to comply with the ErP regulations in force since November 2018 in the EU. The boiler, which features a renewed casing, is designed to allow easy installation and maximum ease of management, boasting a new extremely intuitive user interface. Themis Condens Low NOx combines the simplicity of the traditional boiler with the efficiency of condensing boilers, guaranteeing the right comfort both in heating and in the production of domestic hot water. It is available in a single model with natural gas supply, power equal to 24 kW in both heating and DHW. Themis Condens Low NOx is a boiler specifically designed for high temperature systems. It was developed to give the right comfort, both for the production of sanitary water and to provide the ideal climate in the rooms. Themis Condens low NOx combines the simplicity of the traditional boiler with the efficiency of condensing boilers. The range consists of a single model with combined production of domestic hot water and heating, it is available in natural gas only . Condensing boiler with a new forced draft atmospheric burner studied and designed to have low NOx emissions , traditional copper exchanger protected with a special aluminum paint and aluminum post-condenser. The boiler features a new high-efficiency pump with high performance and a 7-litre expansion vessel. New burner with low NOx emissions (class 6) Designed for replacement in high temperature systems New casing with reduced dimensions High efficiency pump New simple and intuitive user interface Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€620,00
You have seen 24 out of 789 products