NB: BOILER CANNOT BE INSTALLED IN PIEDMONT AND LOMBARDY DUE TO CURRENT REGULATIONS. NB: THIS MODEL IS USED EXCLUSIVELY TO CNG, BUT IT CAN BE CONVERTED TO LPG FREE OF CHARGE THROUGH AN AUTHORIZED SAUNIER DUVAL SERVICE CENTER Technical features ErP efficiency class in heating/DHW: B/A Sanitary load profile: XL Type: Heating and domestic hot water Heating Nominal power P min/max heating 80/60°C: 12.3/26.9 kW Partial load efficiency 30% 40/30 °C %: 99.7 Sanitary Min/Max Rated Power (60°C): 12.5/26.9 kW Specific flow rate (∆T=25 K): l/min 15.4 Electrical characteristics Max power consumption: W 60 Supply voltage/frequency: V/Hz 230/50 Dimensions: Dimensions (h x w x d): 720 x 430 x 330 mm METHANE version THEMIS CONDENS Wall-mounted instantaneous condensing boiler for high temperature systems with forced draft atmospheric burner, traditional copper exchanger protected with a special aluminum paint and aluminum post-condenser. Themis Condens is the ideal condensing solution for replacing traditional wall-mounted boilers that work with high temperature radiators in apartments. The boiler has all the characteristics of simplicity in both installation and management. Themis Condens was developed to give the right comfort, both for the production of domestic hot water and to provide the ideal climate in the rooms. Themis Condens combines the simplicity of the traditional boiler with the efficiency of condensing boilers. Themis Condens runs on methane and can be converted to run on propane. Themis Condens is available in the power of: 24kW for heating and 24kW for domestic hot water production. 27kW for heating and 27kW for domestic hot water production Characteristics: Can be installed indoors. Continuous domestic hot water (DHW) production up to 16 l/min Small dimensions: 72cm high, 40 wide and 33 deep (24 kW) The boiler features a new high-efficiency pump with high performance and a 7-litre expansion vessel. ErP efficiency class B in heating, A in DHW with XL profile. Reliability and Hermann Saunier Duval standard quality Specific for high temperature systems Large passages in the primary exchanger Reduced electricity consumption thanks to the high efficiency pump Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

FERROLI BLUEHELIX PRO S 27 kW CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Characteristics: Heating ERP class: A Healthcare ERP class: A Load profile: XL Heating capacity (PCI) Min / Max Heating 5.3 / 25.2 Heating power 80°C-60°C Min / Max Heating 5.2 / 24.6 kW Useful thermal efficiency 80°C-60°C Pmax % / Pmin % 98.3 / 97.3 Domestic hot water production Δt 30°C 12.7 l/min Heating working pressure Max / Min bar 3 / 0.8 Empty weight kg 32 Dimensions (HxWxD): 700x420x250 mm *Certified operation also with LPG using a special kit to be requested from the Authorized Assistance Centre BLUEHELIX PRO S SMALL FOOTPRINT, GREAT PERFORMANCE ... FULL CONDENSATION BLUEHELIX PRO S has been designed to guarantee maximum energy efficiency and performance both in heating and in the supply of domestic hot water thanks to the new bivalent exchanger in Aisi 316 Ti stainless steel. This new exchanger integrates the heating circuit and the production of instantaneous domestic hot water in a single element, thus optimizing the phenomenon of condensation. The galvanized sheet casing, supplied separately from the boiler body, has been designed to facilitate access to the hydraulic connections and to allow the smoke ducts and air intake pipes to exit on each side of the same. Bluehelix Pro S achieves one of the highest energy efficiency of space heating in its category: ηs 94%. Furthermore, when combined with the external probe and the Romeo remote timer control, it reaches system energy class A+. Strengths: - Achieves one of the highest seasonal space heating efficiency in its category: ηs 94% - A+ SYSTEM: in combination with the Romeo modulating remote timer control and the external probe - Primary heat exchanger in thick Aisi 316 Ti stainless steel with integrated sanitary production (dual stainless steel heat exchanger) - Total premix burner in stainless steel - Digital control panel - Electronic flame modulation both in heating and DHW - Can be combined with the modulating remote timer control - Large backlit multifunction graphic display for easy and correct setting of the parameters - Standard by-pass Advantages: - Exchanger with "SELF-CLEANING" function which reduces limescale deposits inside the DHW circuit - High yields both in heating and in sanitary production - Ease of access to internal components for any maintenance - ECO function in DHW for greater savings in the period of low use of hot water - 3-star certified comfort in sanitary production according to EN 13203, amended by Reg. 812/2013 - Sliding temperature operation via optional external probe - Low consumption modulating heating pump (Erp Ready - Class A) - Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) - Predisposition for solar systems: prearranged for the production of domestic hot water combined with solar panel systems - Certified operation also with propane air (50% air - 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center (max total price of 30 euros + VAT) - Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre. Free transformation during product verification and activation of the guarantee only if the specific code running on LPG is not available. Functions: ECO-COMFORT function: In COMFORT mode, thanks to the particular system for maintaining the temperature of the heat exchanger, the dispensing of domestic hot water becomes even faster and more comfortable. In ECO mode, the production of domestic hot water takes place according to traditional standards. Sliding temperature operation: By installing the “External probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. Antifreeze function: In the event that the temperature in the boiler drops to 5°C, the burner automatically turns on and the circulator is activated in order to protect the appliance from damage caused by freezing. This function is active with the boiler powered by the gas circuit and under electrical voltage. Sun Easy function: BLUEHELIX PRO S has been designed to be easily inserted in systems made with the latest technologies. The SUN EASY system, standard on the boiler, makes use of electronics that simplify the combination with both natural and forced circulation solar panels. Through a sensor placed on the DHW circuit, it continuously monitors the temperature of the water coming from the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. Tangible facts: Regulation 622/2012 provides that all boilers placed on the market from 1 August 2015 are equipped with a low-consumption circulator, otherwise defined as "class A". It is a decision that starts from the consideration of the enormous energy expenditure of the pumps and circulators installed in the various applications. In practice, i.e. by analyzing the impact of the low-consumption circulator integrated in the boiler, it reduces up to 30% of the total electricity consumption of the generator. max consumption standard non-modulating circulator: 0.085 kW max consumption new high efficiency circulator: 0.04 kW Degree days 2500 (average climate zone E) Energy cost: €0.19/kWh Hypothetical annual expenditure at max standard circulator speed: €40.375 Hypothetical annual expenditure max speed high efficiency circulator: 19 € Therefore, with the replacement of standard boilers with Bluehelix Pro S, in line with the new ERP regulations, electricity savings of around 30% can be estimated. In reality, the savings will be even greater, since these are modulating circulators, which at minimum power can reach consumption of up to just 3 W ..SELF ADAPTIVE The low-consumption circulator installed in the Bluehelix Pro S has a variable flow rate, with ΔT control. The advantages o ered are many, including: System start-up from cold: faster start-up with full control of the thermal load on the components Long-lasting maintenance of the temperature equilibrium conditions, once the set point has been reached Better operation in extreme conditions (e.g. at minimum power), reduction of on-OFF states Reactivity to variations in the thermal load, an appreciable quality in multi-zone systems ..ROBUST Others are the merits attributable to the circulator chosen for Bluehelix Pro S: The PWM signal (pulse width modulation) to the circulator allows extremely rapid intervention times to complete an advanced and complete electronic platform. This results in a drastic reduction of the ON-OFF events of the burner and the circulator. Electronic control of the drive torque at start up with consequent reduction of the risk of blocking. The routine anti-seize cycle is in any case carried out every 24 hours of inactivity. Self-protection function in case of overheating Less noise All this translates into greater longevity not only of the circulator, but also of the components subject to wear and tear from frequent on-off cycles. Boiler control The BLUEHELIX control and management electronics allow the user to customize the operation of the appliance in order to manage the environmental comfort according to one's needs. The key control panel and the simple LCD display make the programming operations for the production of hot water, both for domestic hot water and for heating, extremely easy and intuitive. Remote control The BLUEHELIX boiler can be combined with a wide range of remote timer controls which allow the appliance to be adjusted and operated remotely. The ROMEO series consists of 4 models, respectively with weekly or daily comfort programming and with the possibility of choosing between wired or wireless connection for both. With Romeo you can: Adjust the heating and DHW temperatures Know the operating status of the boiler View the temperatures inside and outside the house Restart the boiler in case of temporary lockout Program the daily or weekly environmental comfort Activate/deactivate the heating function via the telephone (dial not supplied) C Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

OPTIONAL RECESSED ENCLOSURE FERROLI BLUEHELIX PRO S 27 kW CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Heating ERP class: A Healthcare ERP class: A Load profile: XL Heating capacity (PCI) Min / Max Heating 5.3 / 25.2 Heating power 80°C-60°C Min / Max Heating 5.2 / 24.6 kW Useful thermal efficiency 80°C-60°C Pmax % / Pmin % 98.3 / 97.3 Domestic hot water production Δt 30°C 12.7 l/min Heating working pressure Max / Min bar 3 / 0.8 Empty weight kg 32 Dimensions (HxWxD): 700x420x260 mm BLUEHELIX PRO S SMALL FOOTPRINT, GREAT PERFORMANCE ... FULL CONDENSATION BLUEHELIX PRO S has been designed to guarantee maximum energy efficiency and performance both in heating and in the supply of domestic hot water thanks to the new bivalent exchanger in Aisi 316 Ti stainless steel. This new exchanger integrates the heating circuit and the production of instantaneous domestic hot water in a single element, thus optimizing the phenomenon of condensation. The galvanized sheet casing, supplied separately from the boiler body, has been designed to facilitate access to the hydraulic connections and to allow the smoke ducts and air intake pipes to exit on each side of the same. Bluehelix Pro S achieves one of the highest energy efficiency of space heating in its category: ηs 94% . Furthermore, when combined with the external probe and the Romeo remote timer control, it reaches system energy class A+ . Strengths: - Achieves one of the highest seasonal space heating efficiency in its category: ηs 94% - A+ SYSTEM : in combination with the Romeo modulating remote timer control and the external probe - Primary heat exchanger in thick Aisi 316 Ti stainless steel with integrated sanitary production (dual stainless steel heat exchanger) - Total premix burner in stainless steel - Digital control panel - Electronic flame modulation both in heating and DHW - Can be combined with the modulating remote timer control - Large backlit multifunction graphic display for easy and correct setting of the parameters - Standard by-pass Advantages: - Exchanger with "SELF-CLEANING" function which reduces limescale deposits inside the DHW circuit - High yields both in heating and in sanitary production - Ease of access to internal components for any maintenance - ECO function in DHW for greater savings in the period of low use of hot water - 3-star certified comfort in sanitary production according to EN 13203, amended by Reg. 812/2013 - Sliding temperature operation via optional external probe - Low consumption modulating heating pump (Erp Ready - Class A) - Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) - Predisposition for solar systems : prearranged for the production of domestic hot water combined with solar panel systems - Certified operation also with propane air (50% air - 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center (max total price of 30 euros + VAT) - Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre. Free transformation during product verification and activation of the guarantee only if the specific code running on LPG is not available. Functions: ECO-COMFORT function : In COMFORT mode, thanks to the particular system for maintaining the temperature of the heat exchanger, the dispensing of domestic hot water becomes even faster and more comfortable. In ECO mode, the production of domestic hot water takes place according to traditional standards. Sliding temperature operation : With the installation of the “External probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. Antifreeze function : In the event that the temperature in the boiler drops to 5°C, the burner automatically turns on and the circulator is activated in order to protect the appliance from damage caused by freezing. This function is active with the boiler powered by the gas circuit and under electrical voltage. Sun Easy function : BLUEHELIX PRO S has been designed to be easily inserted in systems made with the latest technologies. The SUN EASY system, standard on the boiler, makes use of electronics that simplify the combination with both natural and forced circulation solar panels. Through a sensor placed on the DHW circuit, it continuously monitors the temperature of the water coming from the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user.

Read more less