ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 016 T Product Code: 20191960 Optional REC10MH control Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 4.50 Heating COP with water set at 45°C: 3.50 Heating COP with water set at 55°C: 2.85 EER cooling with water set at 7°C: 3.61 EER cooling with water set at 18°C: 2.50 Performance   Heating Useful power in heating with water set at 35° C: 15.90 kW Useful power in heating with water set at 45° C: 16.00 kW Useful power in heating with water set at 55° C: 16.00 kW Cooling down Useful power in cooling with water set at 7 °C: 14.00 kW Useful power in cooling with water set at 18 °C: 14.20 kW Sound data Sound power : 68 dB(A) Sound pressure : 58 dB(A) Electrical data Power supply (V,Hz, Ø) : 380~415/50/3 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1385x945x526 mm Empty weight: 160.0 Kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK Certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   Technical features Model : OMNIA M 3.2 12-T Product code : 2CP000HF Command included Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A+++ SCOP heating with water set at 35 °C : 4.81 SCOP heating with water set at 45 °C : 3.45 SEER cooling with water set at 7 °C: 4.86 SEER cooling with water set at 18 °C: 7.04 Performance   Heating Useful power in heating with water set at 35° C: 12.1 kW Useful power in heating with water set at 45° C: 12.3 kW Useful power in heating with water set at 55° C: 11.9 kW Absorbed power with water set at 35° C: 2.44 kW Absorbed power with water set at 45° C: 3.32 kW Absorbed power with water set at 55° C: 3.90 kW Water flow rate with water set at 35° C : 2081 l/h Water flow rate with water set at 45° C : 2116 l/h Water flow rate with water set at 55° C : 1279 l/h Cooling down Useful power in cooling with water set at 7 °C: 11.5 kW Useful power in cooling with water set at 18 °C: 12.0 kW Absorbed power with water set at 7° C: 4.18 kW Absorbed power with water set at 18° C: 3.04 kW Water flow rate with water set at 7° C : 1978 l/h Water flow rate with water set at 18° C : 2064 l/h Technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Expansion vessel volume: 5 litres Water safety valve setting: 5 bar Minimum system water content: 25 litres Sound power level in heating : 56 ~ 65 dB(A) Sound power level in cooling : 56 ~ 65 dB(A) Electrical data Power supply (V,Hz, Ø) : 380~415/50/3 Refrigerant gas : R32 Maximum absorbed current: 10A Installation data Delivery pipe diameter: 1 ¼” M Return pipe diameter: 1 ¼” M Dimensions and weight Dimensions (WxHxD): 1385x865x526 mm Weight : 129Kg 5 years without worries Ferroli OMNIA M 3.2 Reversible heat pumps for outdoor installation with DC inverter compressor A heat pump with silent and ecological efficiency This series of air-to-water heat pumps with low environmental impact ecological gas R32 satisfies the winter and summer air conditioning needs of residential and commercial systems of small and medium power. All the units are suitable for outdoor installation and being able to produce water up to 65°C they can be used in radiant systems, fan coils, radiators and for the indirect production of DHW domestic hot water via an optional external boiler The units are characterized by the use of a DC inverter compressor which allows the power supplied to be modulated and are complete with a hydronic kit made up of all the essential components for quick and safe installation. The units are characterized by high energy efficiency and low sound levels which allow them to be used as a single generator serving the system or integrated with other energy sources such as electric support heaters or boilers All units are supplied as standard with a DHW tank water temperature probe and with an external air temperature probe, already installed on the unit, to carry out climatic regulation in heating and cooling. All units are carefully built and individually tested in the factory. The installation requires only the electrical and hydraulic connections. In a system it is possible to connect a maximum of 6 units in cascade; one of them will be “MASTER” while the others will be “SLAVE” units. Refrigerant circuit Contained inside the unit to facilitate maintenance operations, it is equipped with a compressor with a Twin rotary type DC Inverter motor to guarantee greater dynamic balancing and reduce vibrations. It is placed on rubber anti-vibration mounts and wrapped in a double layer of sound-absorbing material to reduce noise. The compressor is also equipped with a crankcase oil heater. The circuit is completed by a brazed stainless steel plate heat exchanger complete with antifreeze heater, axial fans with brushless DC motor complete with safety grilles, finned coil with anti-corrosion treatment made up of copper pipes and aluminum fins. All units are equipped with variable speed control of the fans which allows operation with low outside temperatures in cooling and high outside temperatures in heating Hydraulic circuit Contained inside the unit to facilitate maintenance operations, it is equipped as standard with a low-consumption circulator with brushless DC motor, water flow switch, automatic air vent, water pressure gauge, expansion tank, safety valve, Y-shaped water filter The plate heat exchanger and all the hydraulic circuit pipes are thermally insulated to prevent the formation of condensate and reduce heat loss Air source The benefits offered by this technology Aerothermal energy is the energy of the future. Ferroli aerothermal heat pumps use clean technology capable of obtaining up to 79% of the energy supplied for home comfort from the outside air. Ferroli aerothermal heat pumps are designed to provide cooling in summer, heating in winter and/or domestic hot water throughout the year. These latest generation heat pumps with inverter technology and the use of an ecological gas such as R32 do not produce heat from the combustion of a fuel but, simply with minimal energy consumption, exploit the energy in the air and transfer it to the inside the house Greater efficiency The OMNIA M 3.2 monobloc range has energy class A++ for the production of water at 55ºC and A+++ for the water produced at 35°C Compact outdoor unit. More space available Thanks to the adoption of a compact and small-sized unit, especially for the more powerful models, OMNIA M 3.2 can be easily placed outside the house, guaranteeing more available space inside Quick and easy installation Being a packaged unit, installation costs and times are significantly reduced. The interconnection of the refrigerant between the units is not necessary, as the entire refrigerant circuit is contained in the equipment, it is not even necessary to make a connection to bring the fuel, nor to create a flue gas evacuation duct. In addition, the device includes all the plumbing elements necessary for correct and quick connection to the plumbing and DHW heating system. Ideal combination with low temperature systems The OMNIA M 3.2 range can be easily installed in combination with low temperature systems, connecting fan coils, radiators, underfloor heating, to obtain maximum energy efficiency and maximum domestic comfort Easy integration with an existing boiler OMNIA M 3.2 can be combined and integrated with any boiler in the system. The control of the device, based on the external temperature and the required operating conditions, optimizes the production of heat for heating and DHW, using the device with the best efficiency Production of hot water at 65°C with low external temperature The OMNIA M 3.2 range is able to supply hot water at 60°C with an external temperature down to -15°C and at 40°C with an external temperature down to -25°C, without any type of support/accessory. With cold but positive temperatures OMNIA M 3.2 can produce hot water up to 65°C Protection against freezing of hydraulic components without the need to add glycol If low outside temperatures are detected, the circulation pump and the electric antifreeze heater of the plate heat exchanger are activated, thus preventing freezing of the hydraulic components. There is therefore no need to add glycol to the system Control system Operating principle The general control system allows monitoring of all the functions of the inverter system and of the correct functioning of the compressor. It also incorporates regulation algorithms using predefined climatic curves that can be selected by the customer, the management of a DHW circuit, the setting of time slots for noise reduction during the night, alarm signaling, pump block prevention and integration with external heat generators. The user interface consists of a wired remote controller which allows the management of: Management of 2 distinct zones, direct + mixed The unit is able to manage the pumps of both zones and for the mixed in addition the mixing valve and water delivery temperature probe Photovoltaic and Smart Grid management The management of a photovoltaic system and of the "intelligent grid" function is ensured by 2 digital inputs on the PCB with specific operating logics Heating and cooling system The unit activates in hot or cold mode, works by modulating the frequency of the compressor to keep the water temperature produced at the setpoint value set via the controller Domestic hot water production The unit activates in heating mode to maintain the temperature of a DHW tank at the set point value. A 3-way diverter valve is required (not supplied) and a temperature probe, supplied as standard, to be inserted in a well of the DHW boiler. Additional energy sources These sources can be activated in Integration or replacement of the heat pump during heating service or for DHW production and in case the heat pump does not work. Cascade management of several units Possibility of managing up to 6 units in cascade even with different powers with a single controller connected to the Master. In the event of an anomaly in one "Slave", the others can function normally DHW tank electric resistance It is possible to manage a possible integration and/or reserve electric resistance and for the anti-legionella function Fast DHW Function that can be activated manually which allows you to give priority to domestic hot water by bringing the DHW tank to the set point in the shortest possible time Anti-legionella function Weekly anti-legionella cycles can be set. The heat pump must be integrated with a DHW boiler electric heater or boiler Silenced mode 2 levels of silence are possible which, if active, according to an hourly programming, involve a reduction in the maximum frequency of the compressor and in the speed of the fan to reduce the noise emitted perhaps during the night and the power absorbed by the unit ON/OFF The unit can be switched on and off via an external contact. It can be operated from the controller keyboard Hot/Cold The unit can be switched on and off in cold and hot mode via 2 external contacts ECO Possibility of defining time slots and related setpoint for ECO modes in hot and cold mode Weekly programming Allows differentiated time programming for each day of the week by defining the working mode and setpoint for each band Anti-freeze protection Guaranteed up to an external air temperature of -20°C thanks to the heat pump itself operating in hot mode, to the standard anti-freeze electrical resistance and to the electric booster if installed. Remote control of the unit via APP Available for iOS and Android Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : OMNIA M 3.2 14 Product code : 2CP000FF Command included Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A+++ SCOP heating with water set at 35 °C : 4.72 SCOP heating with water set at 45 °C : 3.47 SEER cooling with water set at 7 °C: 4.86 SEER cooling with water set at 18 °C: 6.90 Performance   Heating Useful power in heating with water set at 35° C: 14.5 kW Useful power in heating with water set at 45° C: 14.1 kW Useful power in heating with water set at 55° C: 13.8 kW Absorbed power with water set at 35° C: 3.15 kW Absorbed power with water set at 45° C: 3.92 kW Absorbed power with water set at 55° C: 4.68 kW Water flow rate with water set at 35° C : 2494 l/h Water flow rate with water set at 45° C : 2425 l/h Water flow rate with water set at 55° C : 1484 l/h Cooling down Useful power in cooling with water set at 7 °C: 12.4 kW Useful power in cooling with water set at 18 °C: 12.9 kW Absorbed power with water set at 7° C: 4.96 kW Absorbed power with water set at 18° C: 3.49 kW Water flow rate with water set at 7° C : 2133 l/h Water flow rate with water set at 18° C : 2219 l/h Technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Expansion vessel volume: 5 litres Water safety valve setting: 3 bar Minimum system water content: 25 litres Sound power level in heating : 56 ~ 65 dB(A) Sound power level in cooling : 56 ~ 65 dB(A) Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Maximum absorbed current: 26A Installation data Delivery pipe diameter: 1 ¼” M Return pipe diameter: 1 ¼” M Dimensions and weight Dimensions (WxHxD): 1385x865x526 mm Weight : 129Kg 5 years without worries Ferroli OMNIA M 3.2 Reversible heat pumps for outdoor installation with DC inverter compressor A heat pump with silent and ecological efficiency This series of air-to-water heat pumps with low environmental impact ecological gas R32 satisfies the winter and summer air conditioning needs of residential and commercial systems of small and medium power. All the units are suitable for outdoor installation and being able to produce water up to 65°C they can be used in radiant systems, fan coils, radiators and for the indirect production of DHW domestic hot water via an optional external boiler The units are characterized by the use of a DC inverter compressor which allows the power supplied to be modulated and are complete with a hydronic kit made up of all the essential components for quick and safe installation. The units are characterized by high energy efficiency and low sound levels which allow them to be used as a single generator serving the system or integrated with other energy sources such as electric support heaters or boilers All units are supplied as standard with a DHW tank water temperature probe and with an external air temperature probe, already installed on the unit, to carry out climatic regulation in heating and cooling. All units are carefully built and individually tested in the factory. The installation requires only the electrical and hydraulic connections. In a system it is possible to connect a maximum of 6 units in cascade; one of them will be “MASTER” while the others will be “SLAVE” units. Refrigerant circuit Contained inside the unit to facilitate maintenance operations, it is equipped with a compressor with a Twin rotary type DC Inverter motor to guarantee greater dynamic balancing and reduce vibrations. It is placed on rubber anti-vibration mounts and wrapped in a double layer of sound-absorbing material to reduce noise. The compressor is also equipped with a crankcase oil heater. The circuit is completed by a brazed stainless steel plate heat exchanger complete with antifreeze heater, axial fans with brushless DC motor complete with safety grilles, finned coil with anti-corrosion treatment made up of copper pipes and aluminum fins. All units are equipped with variable speed control of the fans which allows operation with low outside temperatures in cooling and high outside temperatures in heating Hydraulic circuit Contained inside the unit to facilitate maintenance operations, it is equipped as standard with a low-consumption circulator with brushless DC motor, water flow switch, automatic air vent, water pressure gauge, expansion tank, safety valve, Y-shaped water filter The plate heat exchanger and all the hydraulic circuit pipes are thermally insulated to prevent the formation of condensate and reduce heat loss Air source The benefits offered by this technology Aerothermal energy is the energy of the future. Ferroli aerothermal heat pumps use clean technology capable of obtaining up to 79% of the energy supplied for home comfort from the outside air. Ferroli aerothermal heat pumps are designed to provide cooling in summer, heating in winter and/or domestic hot water throughout the year. These latest generation heat pumps with inverter technology and the use of an ecological gas such as R32 do not produce heat from the combustion of a fuel but, simply with minimal energy consumption, exploit the energy in the air and transfer it to the inside the house Greater efficiency The OMNIA M 3.2 monobloc range has energy class A++ for the production of water at 55ºC and A+++ for the water produced at 35°C Compact outdoor unit. More space available Thanks to the adoption of a compact and small-sized unit, especially for the more powerful models, OMNIA M 3.2 can be easily placed outside the house, guaranteeing more available space inside Quick and easy installation Being a packaged unit, installation costs and times are significantly reduced. The interconnection of the refrigerant between the units is not necessary, as the entire refrigerant circuit is contained in the equipment, it is not even necessary to make a connection to bring the fuel, nor to create a flue gas evacuation duct. In addition, the device includes all the plumbing elements necessary for correct and quick connection to the plumbing and DHW heating system. Ideal combination with low temperature systems The OMNIA M 3.2 range can be easily installed in combination with low temperature systems, connecting fan coils, radiators, underfloor heating, to obtain maximum energy efficiency and maximum domestic comfort Easy integration with an existing boiler OMNIA M 3.2 can be combined and integrated with any boiler in the system. The control of the device, based on the external temperature and the required operating conditions, optimizes the production of heat for heating and DHW, using the device with the best efficiency Production of hot water at 65°C with low external temperature The OMNIA M 3.2 range is able to supply hot water at 60°C with an external temperature down to -15°C and at 40°C with an external temperature down to -25°C, without any type of support/accessory. With cold but positive temperatures OMNIA M 3.2 can produce hot water up to 65°C Protection against freezing of hydraulic components without the need to add glycol If low outside temperatures are detected, the circulation pump and the electric antifreeze heater of the plate heat exchanger are activated, thus preventing freezing of the hydraulic components. There is therefore no need to add glycol to the system Control system Operating principle The general control system allows monitoring of all the functions of the inverter system and of the correct functioning of the compressor. It also incorporates regulation algorithms using predefined climatic curves that can be selected by the customer, the management of a DHW circuit, the setting of time slots for noise reduction during the night, alarm signaling, pump block prevention and integration with external heat generators. The user interface consists of a wired remote controller which allows the management of: Management of 2 distinct zones, direct + mixed The unit is able to manage the pumps of both zones and for the mixed in addition the mixing valve and water delivery temperature probe Photovoltaic and Smart Grid management The management of a photovoltaic system and of the "intelligent grid" function is ensured by 2 digital inputs on the PCB with specific operating logics Heating and cooling system The unit activates in hot or cold mode, works by modulating the frequency of the compressor to keep the water temperature produced at the setpoint value set via the controller Domestic hot water production The unit activates in heating mode to maintain the temperature of a DHW tank at the set point value. A 3-way diverter valve is required (not supplied) and a temperature probe, supplied as standard, to be inserted in a well of the DHW boiler. Additional energy sources These sources can be activated in Integration or replacement of the heat pump during heating service or for DHW production and in case the heat pump does not work. Cascade management of several units Possibility of managing up to 6 units in cascade even with different powers with a single controller connected to the Master. In the event of an anomaly in one "Slave", the others can function normally DHW tank electric resistance It is possible to manage a possible integration and/or reserve electric resistance and for the anti-legionella function Fast DHW Function that can be activated manually which allows you to give priority to domestic hot water by bringing the DHW tank to the set point in the shortest possible time Anti-legionella function Weekly anti-legionella cycles can be set. The heat pump must be integrated with a DHW boiler electric heater or boiler Silenced mode 2 levels of silence are possible which, if active, according to an hourly programming, involve a reduction in the maximum frequency of the compressor and in the speed of the fan to reduce the noise emitted perhaps during the night and the power absorbed by the unit ON/OFF The unit can be switched on and off via an external contact. It can be operated from the controller keyboard Hot/Cold The unit can be switched on and off in cold and hot mode via 2 external contacts ECO Possibility of defining time slots and related setpoint for ECO modes in hot and cold mode Weekly programming Allows differentiated time programming for each day of the week by defining the working mode and setpoint for each band Anti-freeze protection Guaranteed up to an external air temperature of -20°C thanks to the heat pump itself operating in hot mode, to the standard anti-freeze electrical resistance and to the electric booster if installed. Remote control of the unit via APP Available for iOS and Android Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : OMNIA M 3.2 16-T Product code : 2CP000JF Command included Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A+++ SCOP heating with water set at 35 °C : 4.62 SCOP heating with water set at 45 °C : 3.41 SEER cooling with water set at 7 °C: 4.67 SEER cooling with water set at 18 °C: 6.71 Performance   Heating Useful power in heating with water set at 35° C: 15.9 kW Useful power in heating with water set at 45° C: 16.0 kW Useful power in heating with water set at 55°C: 16.0 kW Absorbed power with water set at 35° C: 3.53 kW Absorbed power with water set at 45° C: 4.57 kW Absorbed power with water set at 55° C: 5.61 kW Water flow rate with water set at 35° C : 2735 l/h Water flow rate with water set at 45° C : 2752 l/h Water flow rate with water set at 55° C : 1720 l/h Cooling down Useful power in cooling with water set at 7 °C: 14.0 kW Useful power in cooling with water set at 18 °C: 13.6 kW Absorbed power with water set at 7° C: 5.60 kW Absorbed power with water set at 18° C: 3.77 kW Water flow rate with water set at 7° C : 2408 l/h Water flow rate with water set at 18° C : 2339 l/h Technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Expansion vessel volume: 5 litres Water safety valve setting: 3 bar Minimum system water content: 25 litres Sound power level in heating : 56 ~ 69 dB(A) Sound power level in cooling : 56 ~ 69 dB(A) Electrical data Power supply (V,Hz, Ø) : 380~415/50/3 Refrigerant gas : R32 Maximum absorbed current: 12A Installation data Delivery pipe diameter: 1 ¼” M Return pipe diameter: 1 ¼” M Dimensions and weight Dimensions (WxHxD): 1385x865x526 mm Weight : 144Kg 5 years without worries Ferroli OMNIA M 3.2 Reversible heat pumps for outdoor installation with DC inverter compressor A heat pump with silent and ecological efficiency This series of air-to-water heat pumps with low environmental impact ecological gas R32 satisfies the winter and summer air conditioning needs of residential and commercial systems of small and medium power. All the units are suitable for outdoor installation and being able to produce water up to 65°C they can be used in radiant systems, fan coils, radiators and for the indirect production of DHW domestic hot water via an optional external boiler The units are characterized by the use of a DC inverter compressor which allows the power supplied to be modulated and are complete with a hydronic kit made up of all the essential components for quick and safe installation. The units are characterized by high energy efficiency and low sound levels which allow them to be used as a single generator serving the system or integrated with other energy sources such as electric support heaters or boilers All units are supplied as standard with a DHW tank water temperature probe and with an external air temperature probe, already installed on the unit, to carry out climatic regulation in heating and cooling. All units are carefully built and individually tested in the factory. The installation requires only the electrical and hydraulic connections. In a system it is possible to connect a maximum of 6 units in cascade; one of them will be “MASTER” while the others will be “SLAVE” units. Refrigerant circuit Contained inside the unit to facilitate maintenance operations, it is equipped with a compressor with a Twin rotary type DC Inverter motor to guarantee greater dynamic balancing and reduce vibrations. It is placed on rubber anti-vibration mounts and wrapped in a double layer of sound-absorbing material to reduce noise. The compressor is also equipped with a crankcase oil heater. The circuit is completed by a brazed stainless steel plate heat exchanger complete with antifreeze heater, axial fans with brushless DC motor complete with safety grilles, finned coil with anti-corrosion treatment made up of copper pipes and aluminum fins. All units are equipped with variable speed control of the fans which allows operation with low outside temperatures in cooling and high outside temperatures in heating Hydraulic circuit Contained inside the unit to facilitate maintenance operations, it is equipped as standard with a low-consumption circulator with brushless DC motor, water flow switch, automatic air vent, water pressure gauge, expansion tank, safety valve, Y-shaped water filter The plate heat exchanger and all the hydraulic circuit pipes are thermally insulated to prevent the formation of condensate and reduce heat loss Air source The benefits offered by this technology Aerothermal energy is the energy of the future. Ferroli aerothermal heat pumps use clean technology capable of obtaining up to 79% of the energy supplied for home comfort from the outside air. Ferroli aerothermal heat pumps are designed to provide cooling in summer, heating in winter and/or domestic hot water throughout the year. These latest generation heat pumps with inverter technology and the use of an ecological gas such as R32 do not produce heat from the combustion of a fuel but, simply with minimal energy consumption, exploit the energy in the air and transfer it to the inside the house Greater efficiency The OMNIA M 3.2 monobloc range has energy class A++ for the production of water at 55ºC and A+++ for the water produced at 35°C Compact outdoor unit. More space available Thanks to the adoption of a compact and small-sized unit, especially for the more powerful models, OMNIA M 3.2 can be easily placed outside the house, guaranteeing more available space inside Quick and easy installation Being a packaged unit, installation costs and times are significantly reduced. The interconnection of the refrigerant between the units is not necessary, as the entire refrigerant circuit is contained in the equipment, it is not even necessary to make a connection to bring the fuel, nor to create a flue gas evacuation duct. In addition, the device includes all the plumbing elements necessary for correct and quick connection to the plumbing and DHW heating system. Ideal combination with low temperature systems The OMNIA M 3.2 range can be easily installed in combination with low temperature systems, connecting fan coils, radiators, underfloor heating, to obtain maximum energy efficiency and maximum domestic comfort Easy integration with an existing boiler OMNIA M 3.2 can be combined and integrated with any boiler in the system. The control of the device, based on the external temperature and the required operating conditions, optimizes the production of heat for heating and DHW, using the device with the best efficiency Production of hot water at 65°C with low external temperature The OMNIA M 3.2 range is able to supply hot water at 60°C with an external temperature down to -15°C and at 40°C with an external temperature down to -25°C, without any type of support/accessory. With cold but positive temperatures OMNIA M 3.2 can produce hot water up to 65°C Protection against freezing of hydraulic components without the need to add glycol If low outside temperatures are detected, the circulation pump and the electric antifreeze heater of the plate heat exchanger are activated, thus preventing freezing of the hydraulic components. There is therefore no need to add glycol to the system Control system Operating principle The general control system allows monitoring of all the functions of the inverter system and of the correct functioning of the compressor. It also incorporates regulation algorithms using predefined climatic curves that can be selected by the customer, the management of a DHW circuit, the setting of time slots for noise reduction during the night, alarm signaling, pump block prevention and integration with external heat generators. The user interface consists of a wired remote controller which allows the management of: Management of 2 distinct zones, direct + mixed The unit is able to manage the pumps of both zones and for the mixed in addition the mixing valve and water delivery temperature probe Photovoltaic and Smart Grid management The management of a photovoltaic system and of the "intelligent grid" function is ensured by 2 digital inputs on the PCB with specific operating logics Heating and cooling system The unit activates in hot or cold mode, works by modulating the frequency of the compressor to keep the water temperature produced at the setpoint value set via the controller Domestic hot water production The unit activates in heating mode to maintain the temperature of a DHW tank at the set point value. A 3-way diverter valve is required (not supplied) and a temperature probe, supplied as standard, to be inserted in a well of the DHW boiler. Additional energy sources These sources can be activated in Integration or replacement of the heat pump during heating service or for DHW production and in case the heat pump does not work. Cascade management of several units Possibility of managing up to 6 units in cascade even with different powers with a single controller connected to the Master. In the event of an anomaly in one "Slave", the others can function normally DHW tank electric resistance It is possible to manage a possible integration and/or reserve electric resistance and for the anti-legionella function Fast DHW Function that can be activated manually which allows you to give priority to domestic hot water by bringing the DHW tank to the set point in the shortest possible time Anti-legionella function Weekly anti-legionella cycles can be set. The heat pump must be integrated with a DHW boiler electric heater or boiler Silenced mode 2 levels of silence are possible which, if active, according to an hourly programming, involve a reduction in the maximum frequency of the compressor and in the speed of the fan to reduce the noise emitted perhaps during the night and the power absorbed by the unit ON/OFF The unit can be switched on and off via an external contact. It can be operated from the controller keyboard Hot/Cold The unit can be switched on and off in cold and hot mode via 2 external contacts ECO Possibility of defining time slots and related setpoint for ECO modes in hot and cold mode Weekly programming Allows differentiated time programming for each day of the week by defining the working mode and setpoint for each band Anti-freeze protection Guaranteed up to an external air temperature of -20°C thanks to the heat pump itself operating in hot mode, to the standard anti-freeze electrical resistance and to the electric booster if installed. Remote control of the unit via APP Available for iOS and Android Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : OMNIA S 3.2 06 Product code : 0XHK6SWA Command included Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ SCOP heating with water set at 35 °C: 4.95 SEER cooling with water set at 7 °C: 5.34 Performance   Heating Useful power in heating with water set at 35° C: 6.35 kW Useful power in heating with water set at 45° C: 6.30 kW Useful power in heating with water set at 55° C: 6.00 kW Absorbed power with water set at 35° C: 1.28 kW Absorbed power with water set at 45° C: 1.70 kW Absorbed power with water set at 55° C: 2.03 kW Water flow rate with water set at 35° C : 1092 l/h Water flow rate with water set at 45° C: 1084l/h Water flow rate with water set at 55° C : 645 l/h Cooling down Useful power in cooling with water set at 7 °C: 6.50 kW Useful power in cooling with water set at 18 °C: 6.50 kW Absorbed power with water set at 7° C: 2.17 kW Absorbed power with water set at 18° C: 1.35 kW Water flow rate with water set at 7° C : 1118 l/h Water flow rate with water set at 18° C : 1118 l/h External unit technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Sound power level in heating : 53 ~ 61 dB(A) Sound power level in cooling : 54 ~ 61 dB(A) Liquid piping diameter : 6.35 mm (1/4") Gas pipe diameter: 15.88 (5/8") Maximum piping length: 30 m Maximum pipe height difference: 20 m Indoor unit technical data Exchanger type : Brazed stainless steel plates Expansion vessel volume: 10 litres Water safety valve setting: 3 bar Minimum system water content: 40 litres Sound power level : 42 dB(A) System piping diameter: 1" gas F DHW piping diameter: 3/4" gas F Liquid pipe diameter : 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight External unit dimensions (WxHxD): 1008x712x426 mm Outdoor unit weight: 58.0 Kg Internal unit dimensions (WxHxD): 422x702x320 mm 5 years without worries Ferroli OMNIA S 3.2 Reversible heat pumps for split installation with DC inverter compressor Quietness, efficiency and design OMNIA S 3.2 is the new range of split heat pumps Full Inverter R32 by Ferroli. The range includes an Outdoor Unit with the heart of the refrigerant circuit, from the compressor to the fan with the air side exchanger, which is connected to the refrigerant gas pipes towards the Indoor Unit. The Indoor Unit, on the other hand, contains the heart of the hydraulic circuit of the generator with all the main pre-installed components, such as the high-efficiency circulator and the expansion vessel, to safely allow quick and practical installation The split installation of OMNIA S 3.2 , with only the gas pipes between the outdoor and indoor unit, is synonymous with security against any freezing problem, even at the coldest temperatures (down to -25°C) and in the absence of electricity. All units meet the most extreme winter and summer air conditioning requirements, they can in fact produce hot water up to 65°C , which makes them suitable for practically all heating systems, whether radiant, fan coil or radiator, including the production of domestic hot water (DHW), via an external boiler The new conception Full Inverter by Ferroli uses DC inverter modulations on the 3 main energy-intensive components of the machine, i.e. compressor, fan and pump. This allows you to modulate the power supplied by finely tracking the thermal load and allowing the user very high efficiencies and important energy savings . Also, the concept Full Inverter by Ferroli guarantees sound levels among the lowest on the market, avoiding sudden changes in the network and guaranteeing a longer useful life for the components. Indoor and outdoor unit of OMNIA 3.2 The Outdoor Unit contains the heart of the refrigerant circuit, while the Internal Unit the heart of the hydraulic circuit. They are connected to each other by pipes R32 ecological refrigerant gas , which has allowed us to combine high efficiency with a reduced environmental impact. Thanks to his GWP of 675 , about a third of the GWP of R410a, helps reduce CO2 equivalent emissions, the main causes of global warming The heat pumps use the Outdoor Unit to extract heat from the air outside the home and convey it to the water in your system, via an exchanger in the Indoor Unit. That's exactly why they manage to get such high efficiencies , exploiting so renewable the energy already present in the air outside the home The new conception Full Inverter by Ferroli then does the rest, tracking the thermal loads precisely and without waste (modulating the compressor, pump and fan), manages to achieve even greater efficiencies, guaranteeing important savings in bills , without stress on the components and with very low sound levels OMNIA S 3.2 it can be used both as the sole generator of the system and integrated with other sources such as a Ferroli boiler The control system The user interface has been equipped with capsense technology with 2.8” graphic display, which allows the user to interact with the product easily and extremely simply Modbus protocol It can be interfaced to BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting heating and cooling climatic curves, further optimizing consumption for the user Domestic hot water production When the DHW temperature probe calls the machine, it automatically switches to the domestic hot water tank with dedicated DHW set point. 3-way diverter valve supplied as standard Smart Grid input from photovoltaic and grid Digital Smart Grid inputs for the management of an input from the photovoltaic system and from the electricity grid. These allow you to optimize consumption and bill costs DHW tank electrical resistance The DHW electrical integration serves as integration, anti-legionella or reserve source in the event of an anomaly Fast DHW Priority to DHW production to bring the storage tank to the set point in the shortest possible time Anti-legionella function Allows you to set anti-legionella weekly cycles Silent mode Reduces the frequency of the compressor and the speed of the fan, so as to significantly reduce noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, for example from the zone thermostat ECO function Dedicated setpoint for " Eco " operation. Settable with daily time band Anti-freeze protection Heat pump operation with circulator ON and possible electric booster Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : OMNIA S 3.2 10 Product code : 0XHKASWA Command included Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ SCOP heating with water set at 35 °C : 5.19 SEER cooling with water set at 7 °C: 5.98 Performance   Heating Useful power in heating with water set at 35° C: 10.0 kW Useful power in heating with water set at 45° C: 10.0 kW Useful power in heating with water set at 55° C: 9.50 kW Absorbed power with water set at 35° C: 2.02 kW Absorbed power with water set at 45° C: 2.67 kW Absorbed power with water set at 55° C: 3.06 kW Water flow rate with water set at 35° C : 1720 l/h Water flow with water set at 45° C : 1720 /h Water flow rate with water set at 55° C : 1021 l/h Cooling down Useful power in cooling with water set at 7 °C: 8.20 kW Useful power in cooling with water set at 18 °C: 9.90 kW Absorbed power with water set at 7° C: 2.52 kW Absorbed power with water set at 18° C: 2.18 kW Water flow rate with water set at 7° C : 1410 l/h Water flow rate with water set at 18° C : 1703 l/h External unit technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Sound power level in heating : 55 ~ 62 dB(A) Sound power level in cooling : 54 ~ 62 dB(A) Liquid pipe diameter : 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Maximum piping length: 30 m Maximum pipe height difference: 20 m Indoor unit technical data Exchanger type : Brazed stainless steel plates Expansion vessel volume: 10 litres Water safety valve setting: 3 bar Minimum system water content: 40 litres System piping diameter: 1" gas F DHW piping diameter: 3/4" gas F Liquid pipe diameter : 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight External unit dimensions (WxHxD): 1118x865x523 mm Outdoor unit weight: 77.0 Kg Internal unit dimensions (WxHxD): 422x702x320 mm 5 years without worries Ferroli OMNIA S 3.2 Reversible heat pumps for split installation with DC inverter compressor Quietness, efficiency and design OMNIA S 3.2 is the new range of split heat pumps Full Inverter R32 by Ferroli. The range includes an Outdoor Unit with the heart of the refrigerant circuit, from the compressor to the fan with the air side exchanger, which is connected to the refrigerant gas pipes towards the Indoor Unit. The Indoor Unit, on the other hand, contains the heart of the hydraulic circuit of the generator with all the main pre-installed components, such as the high-efficiency circulator and the expansion vessel, to safely allow quick and practical installation The split installation of OMNIA S 3.2 , with only the gas pipes between the outdoor and indoor unit, is synonymous with security against any freezing problem, even at the coldest temperatures (down to -25°C) and in the absence of electricity. All units meet the most extreme winter and summer air conditioning requirements, they can in fact produce hot water up to 65°C , which makes them suitable for practically all heating systems, whether radiant, fan coil or radiator, including the production of domestic hot water (DHW), via an external boiler The new conception Full Inverter by Ferroli uses DC inverter modulations on the 3 main energy-intensive components of the machine, i.e. compressor, fan and pump. This allows you to modulate the power supplied by finely tracking the thermal load and allowing the user very high efficiencies and important energy savings . Also, the concept Full Inverter by Ferroli guarantees sound levels among the lowest on the market, avoiding sudden changes in the network and guaranteeing a longer useful life for the components. Indoor and outdoor unit of OMNIA 3.2 The Outdoor Unit contains the heart of the refrigerant circuit, while the Internal Unit the heart of the hydraulic circuit. They are connected to each other by pipes R32 ecological refrigerant gas , which has allowed us to combine high efficiency with a reduced environmental impact. Thanks to his GWP of 675 , about a third of the GWP of R410a, helps reduce CO2 equivalent emissions, the main causes of global warming The heat pumps use the Outdoor Unit to extract heat from the air outside the home and convey it to the water in your system, via an exchanger in the Indoor Unit. That's exactly why they manage to get such high efficiencies , exploiting so renewable the energy already present in the air outside the home The new conception Full Inverter by Ferroli then does the rest, tracking the thermal loads precisely and without waste (modulating the compressor, pump and fan), manages to achieve even greater efficiencies, guaranteeing important savings in bills , without stress on the components and with very low sound levels OMNIA S 3.2 it can be used both as the sole generator of the system and integrated with other sources such as a Ferroli boiler The control system The user interface has been equipped with capsense technology with 2.8” graphic display, which allows the user to interact with the product easily and extremely simply Modbus protocol It can be interfaced to BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting heating and cooling climatic curves, further optimizing consumption for the user Domestic hot water production When the DHW temperature probe calls the machine, it automatically switches to the domestic hot water tank with dedicated DHW set point. 3-way diverter valve supplied as standard Smart Grid input from photovoltaic and grid Digital Smart Grid inputs for the management of an input from the photovoltaic system and from the electricity grid. These allow you to optimize consumption and bill costs DHW tank electrical resistance The DHW electrical integration serves as integration, anti-legionella or reserve source in the event of an anomaly Fast DHW Priority to DHW production to bring the storage tank to the set point in the shortest possible time Anti-legionella function Allows you to set anti-legionella weekly cycles Silent mode Reduces the frequency of the compressor and the speed of the fan, so as to significantly reduce noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, for example from the zone thermostat ECO function Dedicated setpoint for " Eco " operation. Settable with daily time band Anti-freeze protection Heat pump operation with circulator ON and possible electric booster Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : OMNIA S 3.2 14T Product code : 0XHLESWA Command included Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ SCOP heating with water set at 35 °C : 4.72 SEER cooling with water set at 7 °C: 4.83 Performance   Heating Useful power in heating with water set at 35° C: 14.5 kW Useful power in heating with water set at 45° C: 14.1 kW Useful power in heating with water set at 55° C: 13.8 kW Absorbed power with water set at 35° C: 3.15 kW Absorbed power with water set at 45° C: 3.92 kW Absorbed power with water set at 55° C: 4.68 kW Water flow rate with water set at 35° C : 2494 l/h Water flow rate with water set at 45° C : 2425 /h Water flow rate with water set at 55° C : 1484 l/h Cooling down Useful power in cooling with water set at 7 °C: 12.4 kW Useful power in cooling with water set at 18 °C: 12.9 kW Absorbed power with water set at 7° C: 4.96 kW Absorbed power with water set at 18° C: 3.49 kW Water flow rate with water set at 7° C : 2133 l/h Water flow rate with water set at 18° C : 2322 l/h External unit technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Sound power level in heating : 56 ~ 65 dB(A) Sound power level in cooling : 56 ~ 65 dB(A) Liquid pipe diameter : 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Maximum piping length: 30 m Maximum pipe height difference: 20 m Indoor unit technical data Exchanger type : Brazed stainless steel plates Expansion vessel volume: 10 litres Water safety valve setting: 3 bar Minimum system water content: 40 litres System piping diameter: 1" gas F DHW piping diameter: 3/4" gas F Liquid pipe diameter : 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Electrical data Power supply (V,Hz, Ø) : 380~415/50/13 Refrigerant gas : R32 Dimensions and weight External unit dimensions (WxHxD): 1118x865x523 mm Outdoor unit weight: 112.0 Kg Internal unit dimensions (WxHxD): 422x702x320 mm 5 years without worries Ferroli OMNIA S 3.2 Reversible heat pumps for split installation with DC inverter compressor Quietness, efficiency and design OMNIA S 3.2 is the new range of split heat pumps Full Inverter R32 by Ferroli. The range includes an Outdoor Unit with the heart of the refrigerant circuit, from the compressor to the fan with the air side exchanger, which is connected to the refrigerant gas pipes towards the Indoor Unit. The Indoor Unit, on the other hand, contains the heart of the hydraulic circuit of the generator with all the main pre-installed components, such as the high-efficiency circulator and the expansion vessel, to safely allow quick and practical installation The split installation of OMNIA S 3.2 , with only the gas pipes between the outdoor and indoor unit, is synonymous with security against any freezing problem, even at the coldest temperatures (down to -25°C) and in the absence of electricity. All units meet the most extreme winter and summer air conditioning requirements, they can in fact produce hot water up to 65°C , which makes them suitable for practically all heating systems, whether radiant, fan coil or radiator, including the production of domestic hot water (DHW), via an external boiler The new conception Full Inverter by Ferroli uses DC inverter modulations on the 3 main energy-intensive components of the machine, i.e. compressor, fan and pump. This allows you to modulate the power supplied by finely tracking the thermal load and allowing the user very high efficiencies and important energy savings . Also, the concept Full Inverter by Ferroli guarantees sound levels among the lowest on the market, avoiding sudden changes in the network and guaranteeing a longer useful life for the components. Indoor and outdoor unit of OMNIA 3.2 The Outdoor Unit contains the heart of the refrigerant circuit, while the Internal Unit the heart of the hydraulic circuit. They are connected to each other by pipes R32 ecological refrigerant gas , which has allowed us to combine high efficiency with a reduced environmental impact. Thanks to his GWP of 675 , about a third of the GWP of R410a, helps reduce CO2 equivalent emissions, the main causes of global warming The heat pumps use the Outdoor Unit to extract heat from the air outside the home and convey it to the water in your system, via an exchanger in the Indoor Unit. That's exactly why they manage to get such high efficiencies , exploiting so renewable the energy already present in the air outside the home The new conception Full Inverter by Ferroli then does the rest, tracking the thermal loads precisely and without waste (modulating the compressor, pump and fan), manages to achieve even greater efficiencies, guaranteeing important savings in bills , without stress on the components and with very low sound levels OMNIA S 3.2 it can be used both as the sole generator of the system and integrated with other sources such as a Ferroli boiler The control system The user interface has been equipped with capsense technology with 2.8” graphic display, which allows the user to interact with the product easily and extremely simply Modbus protocol It can be interfaced to BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting heating and cooling climatic curves, further optimizing consumption for the user Domestic hot water production When the DHW temperature probe calls the machine, it automatically switches to the domestic hot water tank with dedicated DHW set point. 3-way diverter valve supplied as standard Smart Grid input from photovoltaic and grid Digital Smart Grid inputs for the management of an input from the photovoltaic system and from the electricity grid. These allow you to optimize consumption and bill costs DHW tank electrical resistance The DHW electrical integration serves as integration, anti-legionella or reserve source in the event of an anomaly Fast DHW Priority to DHW production to bring the storage tank to the set point in the shortest possible time Anti-legionella function Allows you to set anti-legionella weekly cycles Silent mode Reduces the frequency of the compressor and the speed of the fan, so as to significantly reduce noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, for example from the zone thermostat ECO function Dedicated setpoint for " Eco " operation. Settable with daily time band Anti-freeze protection Heat pump operation with circulator ON and possible electric booster Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : OMNIA S 3.2 16T Product code : 0XHLGSWA Command included Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ SCOP heating with water set at 35 °C : 4.62 SEER cooling with water set at 7 °C: 4.67 Performance   Heating Useful power in heating with water set at 35° C: 15.9 kW Useful power in heating with water set at 45° C: 16.0 kW Useful power in heating with water set at 55°C: 16.0 kW Absorbed power with water set at 35° C: 3.53 kW Absorbed power with water set at 45° C: 4.57 kW Absorbed power with water set at 55° C: 5.61 kW Water flow rate with water set at 35° C : 2735 l/h Water flow with water set at 45° C : 2752 /h Water flow rate with water set at 55° C : 1720 l/h Cooling down Useful power in cooling with water set at 7 °C: 14.0 kW Useful power in cooling with water set at 18 °C: 13.6 kW Absorbed power with water set at 7° C: 5.60 kW Absorbed power with water set at 18° C: 3.77 kW Water flow rate with water set at 7° C : 2408 l/h Water flow rate with water set at 18° C : 2563 l/h External unit technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Sound power level in heating : 56 ~ 69 dB(A) Sound power level in cooling : 56 ~ 69 dB(A) Liquid pipe diameter : 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Maximum piping length: 30 m Maximum pipe height difference: 20 m Indoor unit technical data Exchanger type : Brazed stainless steel plates Expansion vessel volume: 10 litres Water safety valve setting: 3 bar Minimum system water content: 40 litres System piping diameter: 1" gas F DHW piping diameter: 3/4" gas F Liquid pipe diameter : 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Electrical data Power supply (V,Hz, Ø) : 380~415/50/3 Refrigerant gas : R32 Dimensions and weight External unit dimensions (WxHxD): 1118x865x523 mm Outdoor unit weight: 112.0 Kg Internal unit dimensions (WxHxD): 422x702x320 mm 5 years without worries Ferroli OMNIA S 3.2 Reversible heat pumps for split installation with DC inverter compressor Quietness, efficiency and design OMNIA S 3.2 is the new range of split heat pumps Full Inverter R32 by Ferroli. The range includes an Outdoor Unit with the heart of the refrigerant circuit, from the compressor to the fan with the air side exchanger, which is connected to the refrigerant gas pipes towards the Indoor Unit. The Indoor Unit, on the other hand, contains the heart of the hydraulic circuit of the generator with all the main pre-installed components, such as the high-efficiency circulator and the expansion vessel, to safely allow quick and practical installation The split installation of OMNIA S 3.2 , with only the gas pipes between the outdoor and indoor unit, is synonymous with security against any freezing problem, even at the coldest temperatures (down to -25°C) and in the absence of electricity. All units meet the most extreme winter and summer air conditioning requirements, they can in fact produce hot water up to 65°C , which makes them suitable for practically all heating systems, whether radiant, fan coil or radiator, including the production of domestic hot water (DHW), via an external boiler The new conception Full Inverter by Ferroli uses DC inverter modulations on the 3 main energy-intensive components of the machine, i.e. compressor, fan and pump. This allows you to modulate the power supplied by finely tracking the thermal load and allowing the user very high efficiencies and important energy savings . Also, the concept Full Inverter by Ferroli guarantees sound levels among the lowest on the market, avoiding sudden changes in the network and guaranteeing a longer useful life for the components. Indoor and outdoor unit of OMNIA 3.2 The Outdoor Unit contains the heart of the refrigerant circuit, while the Internal Unit the heart of the hydraulic circuit. They are connected to each other by pipes R32 ecological refrigerant gas , which has allowed us to combine high efficiency with a reduced environmental impact. Thanks to his GWP of 675 , about a third of the GWP of R410a, helps reduce CO2 equivalent emissions, the main causes of global warming The heat pumps use the Outdoor Unit to extract heat from the air outside the home and convey it to the water in your system, via an exchanger in the Indoor Unit. That's exactly why they manage to get such high efficiencies , exploiting so renewable the energy already present in the air outside the home The new conception Full Inverter by Ferroli then does the rest, tracking the thermal loads precisely and without waste (modulating the compressor, pump and fan), manages to achieve even greater efficiencies, guaranteeing important savings in bills , without stress on the components and with very low sound levels OMNIA S 3.2 it can be used both as the sole generator of the system and integrated with other sources such as a Ferroli boiler The control system The user interface has been equipped with capsense technology with 2.8” graphic display, which allows the user to interact with the product easily and extremely simply Modbus protocol It can be interfaced to BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting heating and cooling climatic curves, further optimizing consumption for the user Domestic hot water production When the DHW temperature probe calls the machine, it automatically switches to the domestic hot water tank with dedicated DHW set point. 3-way diverter valve supplied as standard Smart Grid input from photovoltaic and grid Digital Smart Grid inputs for the management of an input from the photovoltaic system and from the electricity grid. These allow you to optimize consumption and bill costs DHW tank electrical resistance The DHW electrical integration serves as integration, anti-legionella or reserve source in the event of an anomaly Fast DHW Priority to DHW production to bring the storage tank to the set point in the shortest possible time Anti-legionella function Allows you to set anti-legionella weekly cycles Silent mode Reduces the frequency of the compressor and the speed of the fan, so as to significantly reduce noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, for example from the zone thermostat ECO function Dedicated setpoint for " Eco " operation. Settable with daily time band Anti-freeze protection Heat pump operation with circulator ON and possible electric booster Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : OMNIA S IN 3.2 04 Product code : 0XHV4SWA Command included Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in cabinet 016093X0 DHW storage tank integration kit 012086W0 Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A+++ ACS energy class: A Water profile declared in ACS : L SCOP heating with water set at 35 °C : 4.85 SEER cooling with water set at 7 °C: 4.99 Performance   Heating Useful power in heating with water set at 35° C: 4.20 kW Useful power in heating with water set at 45° C: 4.30 kW Absorbed power with water set at 35° C: 0.82 kW Absorbed power with water set at 45° C: 1.13 kW Water flow rate with water set at 35° C : 722 l/h Water flow rate with water set at 45° C : 740 l/h Cooling down Useful power in cooling with water set at 7 °C: 4.70 kW Useful power in cooling with water set at 18 °C: 4.50 kW Absorbed power with water set at 7° C: 1.36 kW Absorbed power with water set at 18° C: 0.82 kW Water flow rate with water set at 7° C : 808 l/h Water flow rate with water set at 18° C : 774 l/h External unit technical data Compressor type : Twin Rotary DC Number of compressors : 1 Number of cooling circuits: 1 Type of fans : DC axial Number of fans : 1 Sound power level in heating : 55 dB(A) Sound power level in cooling : 56 dB(A) Maximum piping length: 30 m Maximum pipe height difference: 20 m Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight External unit dimensions (WxHxD): 1008x712x426 mm Outdoor unit weight: 58.0 Kg 5 years without worries Ferroli OMNIA S IN 3.2 Reversible heat pumps for split installation, built-in solution Maximum architectural integration with a perfect All in One system OMNIA S IN 3.2 is the new split heat pump that completes the range of OMNIA S in R32 , offering performance with a reduced environmental impact, up to 75% lower than equivalent machines in R410A. The new Full Inverter concept by Ferroli uses DC inverter modulations on the 3 main energy-intensive components of the machine, namely the compressor, fan and pump . This makes it possible to modulate the power supplied by finely tracking the thermal load, guaranteeing the user very high efficiencies and significant energy savings on the bill. But that's not all, OMNIA S IN 3.2 is the queen of Architectural Integration . Although inside it contains a 150-litre domestic hot water storage tank, the internal unit and the hydronic kits with circulators and bulky expansion vessels, the installation is so compact that everything fits into a practical cabinet or built-in wardrobe , disappearing. Furthermore, OMNIA S IN 3.2 can be customised : still inside the cabinet, it is possible to add a 30-litre inertial kit for heating/cooling water, integrate a solar thermal system directly into the domestic hot water storage tank and install various distribution groups , e.g. for direct and/or mixed zones The machine can then be managed with the integrated HMI interface or with the CONNECT CRP intelligent remote controller, which can also be accessed via the App . Finally, we can manage the rooms independently through the CONNECT CRP ZONEs , practical and design thermostats that will guarantee comfort in your rooms The control system The user interface has been equipped with capsense technology with 2.8” graphic display, which allows the user to interact with the product easily and extremely simply Modbus protocol It can be interfaced to BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting heating and cooling climatic curves, further optimizing consumption for the user Domestic hot water production When the DHW temperature probe calls the machine, it automatically switches to the domestic hot water tank with dedicated DHW set point. 3-way diverter valve supplied as standard Smart Grid input from photovoltaic and grid Digital Smart Grid inputs for the management of an input from the photovoltaic system and from the electricity grid. These allow you to optimize consumption and bill costs DHW tank electrical resistance The DHW electrical integration serves as integration, anti-legionella or reserve source in the event of an anomaly Fast DHW Priority to DHW production to bring the storage tank to the set point in the shortest possible time Anti-legionella function Allows you to set anti-legionella weekly cycles Silent mode Reduces the frequency of the compressor and the speed of the fan, so as to significantly reduce noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, for example from the zone thermostat ECO function Dedicated setpoint for " Eco " operation. Settable with daily time band Anti-freeze protection Heat pump operation with circulator ON and possible electric booster The brand new Connect CRP and Connect CRP Zone The on-board interface communicates easily with the new Connect CRP intelligent systems, which can manage up to 8 thermostats divided into 2 zones, one direct and one mixed . Connect CRP is the brand new remote controller accessible via APP, available for both iOS and Android. The Connect CRP Zone, on the other hand, is a zone thermostat that communicates via RF with the Connect CRP. It can be placed in a classic 502 box, or left stand-alone on its practical table feet Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION! IN CASE OF UNAVAILABILITY IMMEDIATELY, THE PRODUCT WILL BE ORDERED AND SHIPPED WITHIN 10 WORKING DAYS   FIRST START-UP FREE Technical Features Model : OMNIA S IN 3.2 06 Product Code : 0XHV6SWA Command included Optional accessories Unpainted built-in cabinet 016092X0 Painted built-in wardrobe 016093X0 ACS boiler integration kit 012086W0 Energy Efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A+++ Energy class in ACS: A Water profile declared in ACS: L SCOP heating with water set to 35°C: 4.95 SEER cooling with water set at 7 °C: 5.34 Performance   Heating Useful power in heating with water set at 35° C: 6.35 kW Useful power in heating with water set at 45° C: 6.30 kW Power absorbed with water set at 35°C: 1.28 kW Power absorbed with water set at 45°C: 1.70 kW Water flow rate with water set at 35°C: 1092 l/h Water flow rate with water set at 45°C: 1084 l/h Cooling Useful power in cooling with water set at 7 °C: 6.50 kW Useful power in cooling with water set at 18 °C: 6.50 kW Power absorbed with water set at 7° C: 2.17 kW Power absorbed with water set at 18°C: 1.35 kW Water flow rate with water set at 7°C: 1118 l/h Water flow rate with water set at 18°C: 1118 l/h Technical data of external unit Compressor type : Twin Rotary DC Number of compressors : 1 Number of refrigeration circuits: 1 Fan type : DC Axial Number of fans: 1 Sound power level in heating mode: 58 dB(A) Sound power level in cooling: 58 dB(A) Maximum pipe length: 30 m Maximum pipe height difference: 20 m Electrical Data Power supply (V,Hz,Ø) : 220~240/50/1 Refrigerant gas: R32 Dimensions and Weight External unit dimensions (WxHxD): 1008x712x426 mm External unit weight: 58.0 Kg 5 years without worries Ferroli OMNIA S IN 3.2 Reversible heat pumps for split installation, built-in solution Maximum architectural integration with a perfect All in One system OMNIA S IN 3.2 is the new split heat pump that completes the OMNIA S range in R32 , offering performance with a reduced environmental impact, up to 75% lower than equivalent machines in R410A. Ferroli's new Full Inverter concept uses DC inverter modulations on the 3 main energy-consuming components of the machine, namely compressor, fan and pump . This allows the power supplied to be modulated by finely tracking the thermal load, guaranteeing the user extremely high efficiencies and significant energy savings on the bill. But not only that, OMNIA S IN 3.2 is the queen of Architectural Integration . Despite the fact that it contains a 150 litre domestic hot water tank, the internal unit and the hydronic kits with the circulators and the bulky expansion vessels, the installation is so compact that everything fits into a practical cabinet or a built-in, disappearing cupboard . Furthermore, OMNIA S IN 3.2 is customizable : inside the cabinet it is possible to add a 30-litre inertial kit for heating/cooling water, integrate a solar thermal system directly into the sanitary storage tank and install different distribution groups, e.g. for direct and/or mixed zones. The machine can then be managed with the integrated HMI interface or with the intelligent remote controller CONNECT CRP , also accessible via App . Finally, we can manage the rooms independently via the CONNECT CRP ZONE , practical and designer thermostats that will guarantee comfort in your rooms. The control system The User Interface has been equipped with Capsense technology with 2.8” graphic display, which allows the user to interact with the product in an easy and extremely simple way Modbus protocol It can be interfaced with BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting climatic curves in heating and cooling, further optimising the user's consumption Domestic hot water production When the DHW Temperature probe calls the machine it automatically diverts to the domestic hot water boiler with a dedicated DHW Setpoint. 3-way diverter valve supplied as standard Smart Grid Inputs from photovoltaic and grid Digital Smart Grid inputs for managing an input from a photovoltaic system and from the electricity grid. These allow you to optimise consumption and costs on your bill Electric heating element for ACS boiler The ACS electric integration serves as an integration, anti-legionella or reserve source in the event of an anomaly Fast ACS Priority to DHW production to bring the boiler to the setpoint in the shortest possible time Anti-legionella function Allows you to set weekly anti-legionella cycles Silent mode Reduces the compressor frequency and fan speed, thus significantly reducing noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, e.g. from the zone thermostat ECO function Dedicated setpoint for “ Eco ” operation. Can be set with daily time slot Antifreeze protection Heat pump operation in heating mode with circulator ON and possible electric booster The brand new Connect CRP and Connect CRP Zone The on-board interface communicates easily with the new intelligent Connect CRP systems, which can manage up to 8 thermostats divided into 2 zones, one direct and one mixed . Connect CRP is the brand new remote controller accessible via APP, available for both iOS and Android. The Connect CRP Zone is a zone thermostat that communicates via RF with the Connect CRP. It can be inserted into a classic 502 box, or left stand-alone on its practical table feet. Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION! IN CASE OF UNAVAILABILITY IMMEDIATELY, THE PRODUCT WILL BE ORDERED AND SHIPPED WITHIN 10 WORKING DAYS   FIRST START-UP FREE Technical Features Model : OMNIA S 3.2 04 Product Code : 0XHT4SWA Command included Optional accessories CONNECT CRP remote control Performance Heating Useful power in heating with water set at 35° C: 4.20 kW Useful power in heating with water set at 45° C: 4.30 kW Useful power in heating with water set at 55° C: 4.40 kW Power absorbed with water set at 35°C: 0.82 kW Power absorbed with water set at 45°C: 1.70 kW Power absorbed with water set at 55°C: 1.49 kW Water flow rate with water set at 35°C: 722 l/h Water flow rate with water set at 45°C: 740 /h Water flow rate with water set at 55°C: 473 l/h Cooling Useful power in cooling with water set at 7 °C: 4.70 kW Useful power in cooling with water set at 18 °C: 4.50 kW Power absorbed with water set at 7°C: 1.36 kW Power absorbed with water set at 18°C: 0.82 kW Water flow rate with water set at 7°C: 808 l/h Water flow rate with water set at 18°C: 774 l/h Technical data of external unit Compressor type : Twin Rotary DC Number of compressors : 1 Number of refrigeration circuits: 1 Fan type : DC Axial Number of fans: 1 Sound power level in heating : 53 ~ 60 dB(A) Sound power level in cooling : 52 ~ 60 dB(A) Liquid pipe diameter: 6.35 mm (1/4") Gas pipe diameter: 15.88 (5/8") Maximum pipe length: 30 m Maximum pipe height difference: 20 m Technical data of the internal unit Exchanger type: Brazed stainless steel plates Expansion vessel volume: 10 litres Water safety valve calibration: 3 bar Minimum system water content: 40 litres System pipe diameter: 1" gas F Diameter of ACS pipes: 3/4" gas F Liquid pipe diameter: 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Electrical Data Power supply (V,Hz,Ø) : 220~240/50/1 Refrigerant gas: R32 Dimensions and Weight External unit dimensions (WxHxD): 1008x712x426 mm External unit weight: 58.0 Kg Internal unit dimensions (WxHxD): 595x1860x700 mm 5 years without worries Ferroli OMNIA ST 3.2 Reversible air-water heat pumps for split installation, with integrated DHW storage Efficiency meets comfort for integrated storage OMNIA ST 3.2 is the evolution of OMNIA S 3.2 and is part of the new range of Full Inverter R32 split heat pumps by Ferroli. When we talk about “split” we mean that the refrigeration circuit is divided between the two units, the external one and the internal one. The external unit contains the heart of the refrigeration circuit, from the compressor to the fan with the air side exchanger, which is connected with the refrigerant gas pipes to the internal unit. The internal unit contains the heart of the generator's hydraulic circuit with all the main pre-installed components, such as the high-efficiency circulator and the expansion vessel, to allow for safe, practical and fast installation. The OMNIA ST 3.2 differs from the OMNIA S 3.2 in having an accumulation tank for Domestic Hot Water integrated directly into the internal unit. This accumulation is 190L for sizes 4 to 10, while it is 240L for the larger ones, from 12 to 16T. But not only that, OMNIA ST 3.2 can be customized according to your needs, with an 18L inertial kit, a kit for solar integration on the accumulation or with a kit for the management of 2 different zones, classic direct and mixed, in case we need 2 different temperatures on the terminals in the house Thanks to its wide operating range , among the widest on the market, OMNIA ST 3.2 works down to -25°C external and produces hot water up to 65°C in nominal conditions. The new Full Inverter concept by Ferroli uses DC inverter modulations on the 3 main energy-consuming components of the machine, i.e. compressor, fan and pump. This allows the power supplied to be modulated by finely tracking the thermal load and allowing the user very high efficiencies and significant energy savings . Furthermore, the Full Inverter concept by Ferroli allows the inrush currents to be reduced, avoiding surges in the network and guaranteeing a longer useful life for the components. With noise levels among the lowest on the market , OMNIA ST 3.2 is able to satisfy all system requirements, but can easily be integrated with a Ferroli boiler . The internal unit, the heart of the hydraulic distribution If the external unit contains the heart of the refrigeration circuit, the Internal Unit contains the heart of the hydraulic circuit. OMNIA ST 3.2 is much more than an exchanger with a pump. The hydronic module includes all the main components of the system and can be customized according to the user's needs. Stainless steel plate exchanger, pressure gauge and pressure sensors, expansion vessel, safety valve, automatic vent and brushless DC circulator are just some of the components you will find inside The control system The User Interface has been equipped with Capsense technology with 2.8” graphic display, which allows the user to interact with the product in an easy and extremely simple way Modbus protocol It can be interfaced with BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting climatic curves in heating and cooling, further optimising the user's consumption Domestic hot water production When the DHW Temperature probe calls the machine it automatically diverts to the domestic hot water boiler with a dedicated DHW Setpoint. 3-way diverter valve supplied as standard Smart Grid Inputs from photovoltaic and grid Digital Smart Grid inputs for managing an input from a photovoltaic system and from the electricity grid. These allow you to optimise consumption and costs on your bill Electric heating element for ACS boiler The ACS electric integration serves as an integration, anti-legionella or reserve source in the event of an anomaly Fast ACS Priority to DHW production to bring the boiler to the setpoint in the shortest possible time Anti-legionella function Allows you to set weekly anti-legionella cycles Silent mode Reduces the compressor frequency and fan speed, thus significantly reducing noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, e.g. from the zone thermostat ECO function Dedicated setpoint for “ Eco ” operation. Can be set with daily time slot Antifreeze protection Heat pump operation in heating mode with circulator ON and possible electric booster The brand new Connect CRP and Connect CRP Zone The on-board interface communicates easily with the new intelligent Connect CRP systems, which can manage up to 8 thermostats divided into 2 zones, one direct and one mixed . Connect CRP is the brand new remote controller accessible via APP , available for both iOS and Android . The Connect CRP Zone is a zone thermostat that communicates via RF with the Connect CRP. It can be inserted into a classic 502 box, or left stand-alone on its practical table feet. Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION! IN CASE OF UNAVAILABILITY IMMEDIATELY, THE PRODUCT WILL BE ORDERED AND SHIPPED WITHIN 10 WORKING DAYS   FIRST START-UP FREE Technical Features Model : OMNIA S 3.2 10 Product Code : 0XHTASWA Command included Optional accessories CONNECT CRP remote control Performance   Heating Useful power in heating with water set at 35° C: 10.0 kW Useful power in heating with water set at 45° C: 10.0 kW Useful power in heating with water set at 55° C: 9.50 kW Power absorbed with water set at 35°C: 2.02 kW Power absorbed with water set at 45°C: 2.67 kW Power absorbed with water set at 55°C: 3.06 kW Water flow rate with water set at 35°C: 1720 l/h Water flow rate with water set at 45°C: 1720 /h Water flow rate with water set at 55°C: 1021 l/h Cooling Useful power in cooling with water set at 7 °C: 8.20 kW Useful power in cooling with water set at 18 °C: 9.90 kW Power absorbed with water set at 7° C: 2.52 kW Power absorbed with water set at 18°C: 2.18 kW Water flow rate with water set at 7°C: 1410 l/h Water flow rate with water set at 18°C: 1703 l/h Technical data of external unit Compressor type : Twin Rotary DC Number of compressors : 1 Number of refrigeration circuits: 1 Fan type : DC Axial Number of fans: 1 Sound power level in heating : 55 ~ 62 dB(A) Sound power level in cooling : 54 ~ 62 dB(A) Liquid pipe diameter: 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Maximum pipe length: 30 m Maximum pipe height difference: 20 m Technical data of the internal unit Exchanger type: Brazed stainless steel plates Expansion vessel volume: 10 litres Water safety valve calibration: 3 bar Minimum system water content: 40 litres System pipe diameter: 1" gas F Diameter of ACS pipes: 3/4" gas F Liquid pipe diameter: 9.52 mm (3/8") Gas pipe diameter: 15.88 (5/8") Electrical Data Power supply (V,Hz,Ø) : 220~240/50/1 Refrigerant gas: R32 Dimensions and Weight External unit dimensions (WxHxD): 1118x865x523 mm External unit weight: 77.0 Kg Internal unit dimensions (WxHxD): 595x1860x700 mm 5 years without worries Ferroli OMNIA ST 3.2 Reversible air-water heat pumps for split installation, with integrated DHW storage Efficiency meets comfort for integrated storage OMNIA ST 3.2 is the evolution of OMNIA S 3.2 and is part of the new range of Full Inverter R32 split heat pumps by Ferroli. When we talk about “split” we mean that the refrigeration circuit is divided between the two units, the external one and the internal one. The external unit contains the heart of the refrigeration circuit, from the compressor to the fan with the air side exchanger, which is connected with the refrigerant gas pipes to the internal unit. The internal unit contains the heart of the generator's hydraulic circuit with all the main pre-installed components, such as the high-efficiency circulator and the expansion vessel, to allow for safe, practical and fast installation. The OMNIA ST 3.2 differs from the OMNIA S 3.2 in having an accumulation tank for Domestic Hot Water integrated directly into the internal unit. This accumulation is 190L for sizes 4 to 10, while it is 240L for the larger ones, from 12 to 16T. But not only that, OMNIA ST 3.2 can be customized according to your needs, with an 18L inertial kit, a kit for solar integration on the accumulation or with a kit for the management of 2 different zones, classic direct and mixed, in case we need 2 different temperatures on the terminals in the house Thanks to its wide operating range , among the widest on the market, OMNIA ST 3.2 works down to -25°C external and produces hot water up to 65°C in nominal conditions. The new Full Inverter concept by Ferroli uses DC inverter modulations on the 3 main energy-consuming components of the machine, i.e. compressor, fan and pump. This allows the power supplied to be modulated by finely tracking the thermal load and allowing the user very high efficiencies and significant energy savings . Furthermore, the Full Inverter concept by Ferroli allows the inrush currents to be reduced, avoiding surges in the network and guaranteeing a longer useful life for the components. With noise levels among the lowest on the market , OMNIA ST 3.2 is able to satisfy all system requirements, but can easily be integrated with a Ferroli boiler . The internal unit, the heart of the hydraulic distribution If the external unit contains the heart of the refrigeration circuit, the Internal Unit contains the heart of the hydraulic circuit. OMNIA ST 3.2 is much more than an exchanger with a pump. The hydronic module includes all the main components of the system and can be customized according to the user's needs. Stainless steel plate exchanger, pressure gauge and pressure sensors, expansion vessel, safety valve, automatic vent and brushless DC circulator are just some of the components you will find inside The control system The User Interface has been equipped with Capsense technology with 2.8” graphic display, which allows the user to interact with the product in an easy and extremely simple way Modbus protocol It can be interfaced with BMS/BACS automation and management systems Heating and cooling Full Inverter modulation finely follows the desired setpoints, with the possibility of setting climatic curves in heating and cooling, further optimising the user's consumption Domestic hot water production When the DHW Temperature probe calls the machine it automatically diverts to the domestic hot water boiler with a dedicated DHW Setpoint. 3-way diverter valve supplied as standard Smart Grid Inputs from photovoltaic and grid Digital Smart Grid inputs for managing an input from a photovoltaic system and from the electricity grid. These allow you to optimise consumption and costs on your bill Electric heating element for ACS boiler The ACS electric integration serves as an integration, anti-legionella or reserve source in the event of an anomaly Fast ACS Priority to DHW production to bring the boiler to the setpoint in the shortest possible time Anti-legionella function Allows you to set weekly anti-legionella cycles Silent mode Reduces the compressor frequency and fan speed, thus significantly reducing noise. Programmable on time slots ON/OFF From external contact. Activation and deactivation via an external contact, for example from a zone thermostat Hot / cold From external contacts. Summer/winter switching signal from outside, e.g. from the zone thermostat ECO function Dedicated setpoint for “ Eco ” operation. Can be set with daily time slot Antifreeze protection Heat pump operation in heating mode with circulator ON and possible electric booster The brand new Connect CRP and Connect CRP Zone The on-board interface communicates easily with the new intelligent Connect CRP systems, which can manage up to 8 thermostats divided into 2 zones, one direct and one mixed . Connect CRP is the brand new remote controller accessible via APP , available for both iOS and Android . The Connect CRP Zone is a zone thermostat that communicates via RF with the Connect CRP. It can be inserted into a classic 502 box, or left stand-alone on its practical table feet. Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less