ATTENTION THE WATER HEATER IS SUPPLIED WITH METHANE. FOR CONVERTING TO LPG, CONTACT THE AUTHORIZED AREA SERVICE CENTER IN ADVANCE Ferroli gas water heater for outdoor use EXTERNO 16 NG liters low NOx LPG Energy class A XL load profile Nominal heat input Max / Min kW 32 / 9.5 Thermal power Max / Min kW 29.6 / 8.8 NOx class (according to EN 15502) 6 Maximum working pressure Max / Min bar 10 / 0.2 Sanitary production Δt 25°C Δt 30°C l/min 16 / 14.1 Power supply V/Hz 230 / 50 Electrical protection degree IP X5 Dimensions HxWxD mm 544x384x176 external Wall-mounted Low NOx gas water heater for outdoor installations without smoke ducts EXTERNO is an A3 type instantaneous gas water heater with front flue outlet and suitable for outdoor installation without flue gas evacuation ducts. The water heater is equipped with a combustion unit which, in combination with a LOW NOx type micro-flame burner, guarantees pollutant levels below the parameters imposed by the severe limitations of the European ErP directive. EXTERNO has been designed exclusively for outdoor installations such as on balconies, attics or dedicated shafts. The casing is made up of two molded and IPX5D insulated shells and the water circuit inside the appliance is protected with electrical resistances, fitted as standard, and managed by the electronic card. These measures allow EXTERNO to function correctly up to extreme conditions of -20°C. All appliances are supplied as standard with remote timer control (and 10-metre long connection cable) equipped with a large interface display and simple control keys, to make adjustment easy and intuitive. SOLAR FUNCTION All models in the EXTERNO range can be easily installed in combination with a solar thermal system for the production of domestic hot water. The hydraulic circuit with its components have been designed to be able to operate even at the high temperatures of the water leaving the panels. ECO FUNCTION Through the remote control, it is possible to activate the ECO function. When operating in ECO mode, the EXTERNO water heater will automatically set the hot water outlet temperature to 42°C and at a reduced power of approximately 75% of the nominal power CHILD PROTECTION If the hot water temperature is set to a very high value, each time the water heater is switched OFF, the delivery temperature will automatically return to 48°C so that the next withdrawal takes place in complete safety. The EXTERNO series of water heaters does not have controls on the machine. The DHW temperature control, setting and regulation functions are delegated to a remote control supplied as standard, complete with connection cable. The interface display and the control keys have been designed to make using the control as simple and intuitive as possible. In the event of an anomaly and/or malfunction of the water heater, the indication on the display is accompanied by an audible signal. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

IN THE ABSENCE OF THE PRODUCT, THE NEW MODEL BLUEHELIX RRT C 24 WILL BE SUPPLIED. IT CAN BE VIEWED AT THIS LINK: https://www.climaconviene.it/it/caldaia-a-gas-ferroli-bluehelix-tech-rrt-24c-metano-o-gpl-completa-di-kit-scarico-fumi-new/ Technical features Model : Bluehelix Tech 25C Power supply: methane Energy rating Heating energy efficiency class: A DHW energy efficiency class: A Space heating energy efficiency : ηs 94 % Thermal range Minimum : 5.8 kW Maximum heating : 25.0 kW Maximum DHW : 27.5 kW Thermal power 60°C ~ 80°C Minimum : 5.7 kW Maximum heating : 24.5 kW Maximum DHW : 27.0 kW Thermal power 30°C ~ 50°C Minimum : 6.2 kW Maximum heating : 26.5 kW Useful efficiency 60°C ~ 80°C Minimum : 97.8% Maximum : 98.0 % Useful efficiency 30°C ~ 50°C Minimum : 106.1% Maximum : 107.5% Load reduced 30% : 108.8% Domestic hot water production ∆t 25°C : 15.5 l/min ∆t 30°C : 12.9 l/min Heating operating pressure Minimum : 0.8 bar Maximum : 3 bars Dimensions and weight Dimensions (HxWxD): 600x400x320 mm Empty weight: 28.0 kg Bluehelix Tech Wall mounted condensing, instantaneous or heating only boilers Efficiency, rationality and sturdiness. Recognized The range of generators is equipped with the new AISI 316 TI stainless steel exchanger. Designed and built according to the new ErP directives for eco-compatible design and labelling, Bluehelix Tech is at the top of its category. Bluehelix Tech achieves one of the highest energy efficiency of space heating in its category: ηs 94% . Furthermore, when combined with the external probe and the Romeo remote timer control, it reaches system energy class A+. Components The exchanger Ferroli has directed its research and design towards an exchanger that is simple and robust in its structure, using first-rate materials The exchanger consists of a simple spiral, without joints or welds. The generous section of the pipes allows a free, wide passage of the system fluid. The serpentine shape contrasts the deposit of impurities. The tube bundle is unique, without further parallel circuits. Since it is not a collector type exchanger, it is impossible for air bubbles to remain in the meanders of the circuits. Furthermore, any chemical washing of the boiler will take place effectively, as there is no possibility that the descaler pump pushes through a free circuit rather than a clogged one The tube that makes up the Bluehelix Tech exchanger is made of AISI 316 Ti stainless steel. It is a so-called austenitic alloy, particularly resistant to corrosion, enriched with the addition of titanium. it is also a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits The circulator distribution in class A Regulation 622/2012 provides that all boilers placed on the market from 1 August 2015 are equipped with a low-consumption circulator, otherwise defined as "class A". It is a decision that starts from the consideration of the enormous energy expenditure of the pumps and circulators installed in the various applications. In practice, i.e. by analyzing the impact of the low-consumption circulator integrated in the boiler, it reduces up to 30% of the total electricity consumption of the generator Self-adaptive The low-consumption circulator installed in the Bluehelix Tech has a variable flow rate, with ΔT control. The advantages offered are many, including: Cold system start-up: faster start-up with full control of the thermal load on the components Long-lasting maintenance of the temperature equilibrium conditions, once the set point has been reached Better operation in limit conditions, for example at minimum power, reduction of on-off states Reactivity to variations in the thermal load, an appreciable quality in multi-zone systems Robust Others are the merits attributable to the circulator chosen for Bluehelix Tech: The PWM signal (pulse width modulation) to the circulator allows extremely rapid intervention times to complete an advanced and complete electronic platform. This results in a drastic reduction of the ON-OFF events of the burner and the circulator. Electronic control of the drive torque at start up with consequent reduction of the risk of blocking. The routine anti-seize cycle is in any case carried out every 24 hours of inactivity. Self-protection function in case of overheating. Less noise Boiler control Control panel and functions The BLUEHELIX TECH control and management electronics allow the user to customize the operation of the appliance in order to manage the environmental comfort according to one's needs. The key control panel and the simple LCD display make the programming operations for the production of hot water, both for domestic hot water and for heating, extremely easy and intuitive. The remote control ROMEO Chronocontrol The BLUEHELIX TECH control and management electronics allow the user to customize the operation of the appliance in order to manage the environmental comfort according to one's needs. The key control panel and the simple LCD display make the programming operations for the production of hot water, both for domestic hot water and for heating, extremely easy and intuitive. With ROMEO you can: Adjust the heating and DHW temperatures Know the operating status of the boiler View the temperatures inside and outside the house Restart the boiler in case of temporary lockout Program the daily or weekly environmental comfort Activate/deactivate the heating function via the telephone The ROMEO modulating function allows boiler output to be modulated as the set room temperature value is reached. This improves the quality of comfort by eliminating heat peaks with consequent energy savings Guarantee : All the products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview FERROLI BLUEHELIX TECH 35C CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP 2015: Wall-mounted condensing, premixed, sealed chamber boilers with instantaneous domestic hot water production with double exchanger. IN THE ABSENCE OF THE PRODUCT, THE NEW MODEL BLUEHELIX RRT C 34 WILL BE SUPPLIED, which can be viewed at this link: https://www.climaconvenienza.it/it/caldaia-a-gas-ferroli-bluehelix-tech-rrt-34c-metano-o-gpl-completa-di-kit-scarico-fumi-new/ Technical specifications Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitaryware energy efficiencyprofilXXL Class A Characteristics of heating/sanitary exercises: Sealed chamber condensing boiler Thermal input (PCI)ÿMax Heating: 32 kW Thermal capacity (PCI)ÿMax DHW: 34.8 kW Heating power 80øC-60øCÿMax Heating:ÿ31.4 kW Thermal power 80øC-60øCÿMax Sanitary:ÿ34.1 kW Thermal efficiencyÿ80øC-60øC: 98% Useful thermal efficiencyÿ50øC-30øC: 106.1% Efficiency termicuseÿCaricridott30%: 108.8% Domestic hot water productionÿt 30øC: 16.3 l/min Domestic hot water productionÿt 25øC: 19.5 l/min Energy certification (92/42 EEC): **** Degrees of protection: IPX5D Extremely compact dimensions (hxlxp): 600 x 400 x 320 mm; 31kg Power supply: METHANE Features list BLUE HELIX TECH Wall-mounted condensing boilers, premixed sealed chamber with instantaneous sanitary production New series of compact wall-mounted condensing boilers with instantaneous domestic hot water production. Designed to guarantee maximum energy efficiency in heating and in the supply of domestic hot water, thanks to the new bivalent exchanger patented in AISI 316 TI stainless steel. This new exchanger integrates the heating circuit and the production of domestic hot water in a single element, pushing the phenomenon of condensation to the maximum. Built to be installed outdoors in partially protected places and equipped with electronics capable of integrating with a solar panel system. The range: Range made up of two models, respectively 27 and 35 kW, running on methane, LPG, propane air. Strengths: Boiler body with patented high performance primary heat exchanger in AISI 316 TI stainless steel Instantaneous production of domestic hot water with a dedicated plate domestic hot water exchanger Total premix burner in stainless steel Digital control panel Electronic flame modulation in both heating and DHW Can be combined with the modulating remote timer control Large graphic multifunction display with backlighting for easy and correct setting of the parameters Standard by-passÿ Refined design compact size Casing painted white by anaphoresis with epoxy powders Advantages : ÿECOÿfunctionin sanitaryware for greaterÿsavingÿin the period of low use of hot water 3-star certified comfort in sanitary production according to EN 13203 Sliding temperature operationÿby means of an optional external probe Low-consumption modulating heating circulator (Erp Ready - Class A):ÿRegulation 622/2012 requires that all boilers placed on the market from 1 August 2015 be equipped with a low-consumption circulator, otherwise defined as class A. This is a decision that starts from consideration of the enormous energy expenditure of the pumps and circulators installed in the various applications. In practice, or by analyzing the impact of the low-consumption circulator integrated in the boiler, this reduces the total electricity consumption of the generator by 30%. Digital flame monitor with three re-ignition attempts in the event of blockage due to lack of flame detection (methane model) Predisposition for solar systems:ÿpredisposed for the production of domestic hot water combined with solar panel systems Place of installation:ÿalso for outdoorsin a partially protected place up to -5øC as standard and up to -15øC with the aid of the optional antifreeze heater kit Operation certified also with propane airÿ (50% air - 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center Appliance belonging to class 5, the most ecological required by European standards (UNI EN 297 NOX and 483) Products that fall under the tax benefits provided for by the Finance Law in force Functions: ECO-COMFORT function: In COMFORT mode, thanks to the particular system for maintaining the temperature of the heat exchanger, the delivery of domestic hot water becomes even more rapid and comfortable. In ECO mode, the production of domestic hot water takes place according to traditional standards. Sliding temperature operation:ÿWith the installation of the kit or External probe? possible to operate the boiler in sliding temperature. This means that without acting on the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while guaranteeing maximum comfort for the user. Antifreeze function: In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by freezing. This function is active with the boiler powered by the gas circuit and electrical undervoltage. Sun Easy function: BLUEHELIX TECH has been designed to be easily inserted in systems made with the most recent technologies. The SUN EASY system, standard on the boiler, makes use of electronics that simplify the combination with both natural and forced circulation solar panels. By means of a post sensor on the sanitary circuit, it continuously checks the temperature of the water coming from the solar panels, foreseeing the ignition of the burner only when the latter drops to the level necessary to guarantee optimal comfort for the user. Tangible facts: Regulation 622/2012 provides that all boilers placed on the market from August 1, 2015 be equipped with a low-consumption circulator, otherwise defined as class A. This is a decision that starts from the consideration of the enormous energy expenditure of the pumps and circulators installed in the various applications. In practice, or by analyzing the impact of the low-consumption circulator integrated in the boiler, this reduces the total electricity consumption of the generator by 30%. consumption max. standard non-modulating circulator:ÿ0.085 kWÿ consumption max. new high efficiency circulator:ÿ0.04 kWÿ Degree daysÿ2500ÿ(average climate zone E)ÿ Energy cost:ÿ0.19 ??¶/kWhÿ Hypothetical annual expenditure at max standard circulator speed:ÿ40.375 ??¶ÿ Hypothetical annual expenditure max speed high efficiency circulator:ÿ11.4 ??¶ÿ Therefore, with the replacement of standard boilers with Bluehelix Pro, in line with the new ERP regulations, electricity savings of around 30% can be estimated. In reality, the savings will be even greater, since these are modulating circulators, which at minimum power can reach consumption of up to just 3 W ERP extension The new European regulations for heat generatorsÿ The 4 ErP Regulations on: ÿEcodesignÿ (minimum efficiency limits) and Energy Labeling (information energy label) are mandatory European provisions automatically in force from 26 September 2015 simultaneously in the 28 EU countries and in all EEA countries (European Economic Areas: Liechtenstein, Switzerland, Norway, Iceland). The Regulations (or EU Regulation? nr.: 811/2013, 812/2013, 813/2013 and 814/2013) are already published by the EU and are legal provisions which leave no legislative power (of modification/variation of delayed adoption) to the EU Member States, in so far as they do not require any national law of adoption, but come into force automatically or per se? throughout Europe.ÿ From 26th September 2015, boilers, heat pumps, tanks/boilers, water heating systems or non-ErP compliant systems will not be able to leave the factories and warehouses of MANUFACTURERS (nor from the warehouses of IMPORTERS from outside the EU), except for products for which it has already been carried out the placing on the market or the transfer of formal ownership (before 26 September) to the first customer/distributor of the commercial chain. The date which is the date on which the finished product was first placed on the market. In practice, by virtue of the new Regulations, manufacturers in the EU area and importers from outside the EU will be obliged to offer for sale only highly efficient products and systems, both for space heating and for the preparation of domestic hot water. Will the end customer be able to find latest generation products immediately on the market? which will be compulsorily accompanied by the ENERGY LABEL and compliant with the MINIMUM LIMITS calculated according to strict European standards which for the first time for these new products or ErP? considers all types of direct and indirect consumption of appliances, e.g. gas consumption and electricity consumption in a boiler.ÿ New ErP efficiency limits (and noise for heat pumps only) will apply to heating systems (boilers and heat pumps) up to 400 kW, to instantaneous gas and electric water heater systems up to 400 kW, to DHW tanks up to 2,000 kW lt. All new products and systems must be of very high efficiency, with the sole exception of tipB1x boilers (open chamber with natural draft) which will have a special derogation and may still be manufactured and sold exclusively to be installed in REPLACEMENTS on COLLECTIVE FLUES . Heat pumps will have to comply with new minimum limits for noise emissions, while for boilers the noise value will have to be indicated (without limit constraints). Furthermore, even the circulators mounted on board all the products must comply with new minimum efficiency standards (very high efficiency), based on the specific EU Regulations (nr. 641/2009 and nr. 622/2012). To make the most of all the possibilities offered by the energy label, will it be possible to predict and declare their use in a system right from the product conception and development stage? with other devices (e.g. regulation and control), thus proposing a globally more efficient whole, e.g. eg. through the use of renewable sources (solar thermal, geothermal aerothermal energy, biomass). Even the so-called or standard products? today the best sellers - i.e. boilers for gas heating - will undergo a forced evolution towards technology with heat recovery from fumes (condensing boiler). We remind you that condensing boilers can recover the heat from the fumes in most of the existing systems, even those with radiators, with the use of thermostatic valves now available in various models (also programmable individually on different times), due to their different conception of design incorporating substantial improvements over previous or standard boilers? such as the new highly efficient modulating circulators and the combustion control volume in the new premix burners. Subsequently, for products sold by manufacturers and importers from outside the EU after 26 September 2018, more stringent limits for NOx emissions will come into force Theÿ20/20/20 climate-energy package?ÿsets ambitious targets for the reduction of greenhouse gas emissions, energy consumption as well as the increase in the use of renewable energies, corresponding to a percentage of 20% to be reached by 2020. In this context , the regulationeuropeErP (Energy Related Products) introduces an energy classification also for hot water generators for space heating and domestic hot water purposes. This classification translates into an ÿenergy labelÿ which must necessarily accompany all the products affected by the Regulation, introduced on the market from 26 September 2015. The labeling constitutes an easy guide for the consumer, who can choose - through standardized and objective indications - the most efficient product. In this way, the choice will be the most sparing in terms of consumption for the benefit of the user, but also the most virtuous for energy balances and consequently, for the environment. The most significant parameters indicated on the label are the seasonal efficiency index in heating and efficiency in the eventual production of domestic hot water, according to a scale which in the casdel prodottsingolcaldaia ranges from A to G*. Furthermore, for combined boilers, a load profile is indicated corresponding to the domestic hot water flow rate of the appliances measured in a series of sample samples, thus guaranteeing the declared sanitary efficiency. This index is identified with a letter/?size? (S, M,¶ÝXXL). Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

FERROLI BLUEHELIX K 50 25 Kw CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Characteristics: Seasonal space heating energy efficiency class A Water heating energy efficiency class A Declared load profile XL Heat Capacity (PCI) Min / Max Heating: 5.8 / 25.0 Thermal power 80°C-60°C: 5.7 / 24.5 Useful thermal efficiency 80°C-60°C Pmax % / Pmin %: 98.0 / 97.8 Emission class Nox class 5 Boiler capacity 50 litres Domestic hot water production Δt 30°C l/10 min 175 Sanitary Manufacturing (EN 13203) ★★★ Heating working pressure Max bar 3 DHW working pressure Max bar 9 Empty weight kg 50 Dimensions HxWxD: 800 x 600 x 420 Power supply: METHANE Certified operation also with LPG using a special kit to be requested from the Authorized Assistance Centre CHARACTERISTICS Boiler body with the new patented primary exchanger in thick AISI 316 TI stainless steel Production of domestic hot water with 50-litre stainless steel domestic hot water storage tank Total premix burner in stainless steel Electronic flame modulation both in heating and DHW Digital control panel Can be combined with the modulating remote timer control Low consumption modulating heating pump (Erp Ready - Class A) Refined design and compact size Casing painted in white by anaphoresis with epoxy powders 3-star certified comfort in sanitary manufacturing according to EN 13203 Sliding temperature operation via optional external probe Digital flame control with three re-ignition attempts in case of operation due to lack of flame detection (methane model) Arrangement for recirculation attachments Standard by-pass Place of installation: also for outdoors in a partially protected place up to - 5 ° C as standard TANGIBLE FACTS max consumption standard non-modulating circulator: 0.085 kW max consumption new high efficiency circulator: 0.04 kW Degree days 2500 (average climate zone E) Energy cost: €0.19/kWh * Hypothetical annual expenditure at max standard circulator speed: €40.375 Hypothetical annual expenditure at max speed of high efficiency circulator: €11.4 Therefore, with the replacement of standard boilers with Bluehelix K 50, in line with the new ERP regulations, electricity savings of around 30% can be estimated. In reality, the savings will be even greater, since these are modulating circulators, which at minimum power can reach consumption of up to just 3 W. The low-consumption circulator installed in the Bluehelix K 50 has a variable flow rate, with ΔT control. The advantages o ered are many, including: System start-up from cold: faster start-up with full control of the thermal load on the components Long-lasting maintenance of the temperature equilibrium conditions, once the set point has been reached Better operation in limit conditions (e.g. at minimum power), reduction of on-oFF states Reactivity to variations in the thermal load, an appreciable quality in multi-zone systems ..ROBUST Others are the merits attributable to the circulator chosen for Bluehelix K 50: The PWM signal (pulse width modulation) to the circulator allows extremely rapid intervention times to complete an advanced and complete electronic platform. This results in a drastic reduction of the ON-OFF events of the burner and the circulator. Electronic control of the drive torque at start up with consequent reduction of the risk of blocking. The routine anti-seize cycle is in any case carried out every 24 hours of inactivity. Self-protection function in case of overheating Less noise All this translates into greater longevity not only of the circulator, but also of the components subject to wear and tear from frequent on-off cycles. COMFORT AND SAFETY The designers have thought of a series of functions capable of guaranteeing the quality of the domestic water, the best delivery of power to the heating system combined with a longer life for the appliance. SLIDING TEMPERATURE OPERATION With the installation of the “external probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. ANTI-LEGIONELLA FUNCTION In order to keep the storage cylinder in suitable hygienic-sanitary conditions, the product electronics are able to keep it at a temperature of 65°C at programmable time intervals from one to seven days. ANTI-BLOCK FUNCTION In order to avoid blockage and consequent damage to the heating circulator and the three-way diverter valve, after a set period of inactivity, the boiler electronics activate operation for a few seconds. ANTIFREEZE FUNCTION In the event that the temperature in the boiler drops to 5°C, the burner automatically turns on and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. ECONOMY/COMFORT FUNCTION By activating the appropriate key, heating/temperature maintenance can be excluded by the user (Economy). This makes it possible to reduce fuel consumption during periods of non-use of domestic water Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Ferroli Bluehelix TOP RRT 34C methane or LPG condensing boiler Complete with Smoke Exhaust Kit Remote Control Dirt Remover and Dosing Pump STANDARD 0T3F3XWA - NEW Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XXL Class A Characteristics of heating/DHW operation: Thermal power 80°C-60°C Max Heating: kW 97,9 / 98 Heating max / min heat input (Hs) kW 34 / 3.2 Thermal power 50°C-30°C Max Sanitary: 106.1 / 107.5 kw Useful thermal efficiency 30%: 109.5 Max working pressure heating bar 3 Sanitary flow rate ∆t 25°C 19.5 NOx class 6 Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x320 Free methane/LPG/propaneted air transformation when checking the product and activating the warranty, to be requested from the Authorized Assistance Center - MGR: Methane, LPG, Propane air Ready through a simple configuration the boiler is able to operate on methane, LPG and propane air without the use of additional conversion kits BLUEHELIX TOP RRT STRENGTHS: - Boiler with thick stainless steel primary exchanger, with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt - Boiler particularly robust and suitable for replacement even in particularly critical and resistant systems - Wide range of accessories supplied as standard with the product: CONNECT, latest generation wifi remote control with management via app / Magnetic dirt separator filter with corrosion inhibitor / Polyphosphate dosing filter for domestic hot water inlet - Boosted modulating heating circulator with high head on all models able to adapt even to particularly resistant systems (Erp Ready - Class A) - Enhanced domestic hot water exchanger with a high number of plates particularly immune to blockages and capable of maintaining the domestic hot water production capacity constant over time - A+ System : thanks to the combination with the CONNECT modulating remote control supplied as standard and reading the outside temperature directly from the internet, it reaches maximum energy efficiency A+ (scale from G to A+++) - Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:12 (mod. 34C, 1:10 mod. 28C) - MC2 : Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) - MGR: Methane, LPG, Propane air Ready through a simple configuration the boiler is able to operate on methane, LPG and propane air without the use of additional conversion kits - Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace - Hydraulic connections covered by the boiler shell, standard by-pass > BENEFITS OF BLUEHELIX TOP RRT C: - Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes - FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard - Designed to simplify and facilitate normal maintenance and cleaning operations - STOP AND GO: It is possible to delay the ignition of the burner by activating it only in the face of real withdrawals of domestic hot water - Minimum polluting emissions (class 6 according to EN 15502-1) - Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) - Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit - Transformation of methane/LPG/Free propane air Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

Casing excluded Ferroli BLUEHELIX RRT 24 H Solar condensing boiler with 130 L stainless steel storage tank for solar integration - ErP ERP Class (Class G - A++) A Heating max / min heat input (Hs) kW 24.5 / 5.0 Max / min heat output heating (80/60°C) kW 24 / 4.9 Max / min heat output heating (50/30°C) kW 26.0 / 5.4 Efficiency Pmax / Pmin (80-60°C) (Hi) % 98.1 / 98.0 Efficiency Pmax / Pmin (50-30°C) (Hi) % 106.1 / 107.5 Yield 30% % 109.7 Max / min heating pressure bar 3 / 0.8 CNG/LPG CODE 0T3D2BWA BLUEHELIX RRT H > STRONG POINTS: Heating only boiler combined with a double coil stainless steel DHW storage tank (130 litres) with solar integration and recirculation connection Boiler with thick stainless steel primary exchanger, with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt in combination with the modulating remote control and the external probe (optional) reaches the upper efficiency class A+ (scale from G to A+++) MC2 : Multi Combustion Control, new combustion system with patented gasadaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace. Integrated management of up to a maximum of three heating zones, one of which is direct (standard at high temperature) and two mixed (through the use of optional kits) Solar circuit complete with hydraulic unit and electronic management card for coupling to solar thermal collectors Solar collector flow probe available as an optional accessory - Low consumption modulating solar circuit pump (ErP - Class A) Completely encasable monobloc casing that does not require pre-assembly operations on site > ADVANTAGES: Integrated management in a single device of up to three system zones, of the production of sanitary water and of one or more solar thermal collectors Minimum polluting emissions (class 6 according to EN 15502-1) - Sanitary accumulation with inspection flange to facilitate cleaning operations Hydraulic connections in a raised position which make connection operations to the system extremely easy Sliding temperature operation with optional external probe Heating and DHW circuit anti-freeze protection, pump/3-way valve anti-blocking and anti-legionella protection as standard FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard Designed to simplify and facilitate normal maintenance and cleaning operations Low consumption modulating heating pump (ErP Ready - Class A) Free methane/LPG/propaneted air transformation when checking the product and activating the warranty, to be requested from the Authorized Assistance Center Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

Ferroli condensing boiler Bluehelix HiTech RRT 34 H complete with low NOx methane or LPG fume exhaust kit for heating only - New Heating ERP Class A Heating capacity max / min kW 34.7 / 3.5 Efficiency 30% % 109.5 NOx emission class (EN 15502-1) - 6 Heating expansion vessel capacity 8 litres Protection degree (IEC 60529) IP X4D Dimensions HxWxD mm 700x420x320 Bluehelix HiTech RRT H (Heating Only)   The new user interface with «capsense» technology, without mechanical keys and equipped with a 2.8'' graphic display, allows the user to interact with the product easily and extremely simply. Thanks to the energy efficiency of the space heating ηs 94% among the highest in the category (Class A ErP, scale from G to A++) and to the combination with the Connect remote control, able to read the external temperature directly from the internet, reaches the system energy class A+ (scale from G to A+++). Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:10 (1:10 mod. 34 C, 1:9 mod. 28 C, 1:7 mod 24 C). Thanks to the "Hydrogen plug-in" system, one of its most important innovations, it is already able to self-regulate to work with mixtures of natural gas and hydrogen, which will soon arrive in Europe, to combat global warming. Designed to fully satisfy the requests for a "robust" product from every point of view thanks to the high-passage primary exchanger capable of guaranteeing maximum efficiency and reliability over time also, and not only, as a replacement for old generators in particularly dirty systems . Silence at the top The particularly careful design of BLUEHELIX HITECH RRT has made it possible to achieve significant values ​​in terms of silence and acoustic comfort, so much so that it could almost be difficult to distinguish the background noise of a home from the noise produced by the boiler during normal operation. It will be difficult to realize whether the boiler is on or off from its noise, as on older generations of boilers, because even the on/off transients have been optimized according to acoustic comfort. The planning also took care of the design, creating a precious mantle in 3 removable pieces, which descends to cover the pipe connections Characteristics Boiler with thick stainless steel primary exchanger , with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt thanks to the combination with the CONNECT modulating remote control and the reading of the external temperature directly from the internet, it reaches the maximum energy efficiency A+ (scale from G to A+++) Class 6 NOx: already in line with the provisions of the ErP regulation from 26.09.2018 (NOx emissions < 56mg/kWh) MC2: Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) MGR: Methane LPG Ready, through a simple configuration the boiler is able to operate on both methane and LPG without the use of additional conversion kits Exclusive exchanger-burner system with self-cooled door (without insulators): simplifies maintenance and reduces its cost thanks to fewer perishable parts Hydraulic connections covered by the boiler shell Large backlit multifunction graphic display for easy and correct parameter setting Standard by-pass Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:10 (1:10 mod. 34 C, 1:9 mod. 28 C, 1:7 mod 24 C). Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard Designed to simplify and facilitate normal maintenance and cleaning operations Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (only for methane operation) Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit Boiler control The new user interface with ''capsense'' technology, without mechanical keys and equipped with a 2.8'' graphic display, allows the user to interact with the product easily and extremely simply, customizing the operation of the appliance in so as to manage the environmental comfort according to one's needs. Thanks to the remote connection via bus, this can also be done directly from the CONNECT remote control, even via smartphone. The boiler is also set up to connect a second room thermostat to dedicated terminals to manage multi-zone systems. TOP EFFICIENCY Even on old systems (replacements) The BLUEHELIX HITECH RRT heat exchanger THERMOBALANCE™ (fig. A) compared to the more classic and widespread steel exchanger (fig. B) also used in the past by the Ferroli Group exclusively on a small series of boilers produced for the market English, and then immediately abandoned in favor of the evolution towards the proprietary steel exchanger used in the Bluehelix models (2012 -> ). This geometry allows the heat exchanger of the THERMOBALANCE heating unit to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig . B tends to block up much faster in the part in contact with the flame due to the reduced passage area of ​​the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values MC2 Multi Combustion Control The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). EASY MAINTENANCE Trouble-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the "Thermobalance"TM thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: Internal accessibility is favored by the 3-piece mantle with removable side panels. The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - The fan, offset from the burner and placed underneath, must not be disassembled to access the steel burner-exchanger group. The burner door is totally self-air-cooled and therefore does not require an insulating panel, avoiding the risk that this could be damaged or broken during disassembly for cleaning. The burner can be disassembled by loosening just 3 bolts leaving free access to the stainless steel exchanger. The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

FERROLI DIVATOP 60 C24 OPEN CHAMBER GAS BOILER METHANE NEW ErP Technical features Characteristics: Heating max heat input kW 25.8 Minimum heating heat input kW 11.5 Max DHW heat input kW 25.8 Minimum DHW heat input kW 11.5 Directive efficiency class 92/42 EEC ★★ NOx class 3 Max. heating operating pressure bar 3 Max heating temperature 90 °C Heating expansion vessel capacity 8 litres Max working pressure san. bar 9 Sanitary flow rate ∆t 30°C l/h 740 IP X5D degree of protection Supply voltage V/Hz 230V/50Hz Electric power absorbed W 59 DHW absorbed electrical power W 59 Dimensions HxW : 800 x 600 Certified operation also with LPG using a special kit to be requested from the Authorized Assistance Centre DIVATOP C60 STRENGTHS 60-litre rapid exchange storage tank in AISI 316 stainless steel Two low consumption circulators for the heating system and for the storage coil Exclusive compact geometry heat exchanger entirely in copper Combustion chamber in anti-corrosion aluminized sheet metal, internally insulated with ecological fibre Intake air burner, with AISI 304 stainless steel ramps, electric ignition without pilot flame, with microprocessor flame ionization current detection safety device Modulating heat input in both heating and DHW production Standard by-pass Standard 2-litre sanitary expansion tank Use of digital microprocessor electronics for flame regulation and safety Flow temperature scrolling with external probe (optional) Possibility of connection to the remote timer control (optional) ADVANTAGES OF DIVATOP 60: Place of installation: also for outdoors in a partially protected place up to -10°C as standard, with the addition of the wind protection kit Robust casing in white painted steel, which can be individually disassembled on the three sides of the product for easy access to the internal parts Arrangement of the internal organs in such a way as to be easily accessible directly from the front casing, so as to ensure, in case of need, the greatest ease of intervention Ease of use thanks to a complete user interface, multifunctional display with graphic symbols for immediate reading Perforated grid to cover the connections supplied as standard Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre. Free transformation during product verification and activation of the guarantee only if the specific code running on LPG is not available Operation certified also with propane air (50% air - 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center Quick and easy installation thanks to the hydraulic connections well spaced from the wall Warranty The warranty on this item is 24 months from the date of purchase.

Read more less

Heat pump water heater Ferroli EGEA LT 90 A+ Wi-Fi integrated Technical features Product code: 2COBA00F Energy label specifications according to the European ErP directive Energy efficiency: Class A+ Characteristics of heating/DHW operation: Nominal accumulation capacity l 89 Maximum capacity of hot water at 40°C l 98 Storage dispersion W 40 Average electrical power absorbed Wel 270 Dimensions (Ø x H) mm 510 x 1380 Nominal air flow m3 /h 190 Required room volume m3 15 Power supply parameters V-Hz 230V - 50H Protection class IP24 Sound power indoors Lw(A) dB(A) 52 Anti-legionella system AutomaticAnti-corrosion system n. 1 Mg anode Operating modes Auto, Eco, Boost, Elec. Heater, Fan EGEA EGEA is a brand new range of storage heat pump water heaters for the production of domestic hot water, suitable for small residential applications. It is a smart solution for heating sanitary water, which uses electricity, air and possibly solar thermal and photovoltaic energy, leaving out the use of traditional fuels. Efficiency, ecology, flexibility and the new aesthetics are the characteristics that distinguish EGEA and differentiate it from a traditional electric water heater . * The 90 and 120 LT models use R-290 gas, a valid “green” alternative to the most common high GWP (Global Warming Potential) refrigerants in the sector. It is a naturally occurring hydrocarbon (HC) with a GWP of 3 and an ODP (Ozone Depletion Potential) of 0 FEATURES at a glance... EGEA mod. 90 / 120 / 200 / 260 EGEA is an air-water heat pump for the production of domestic hot water, storage in an enamelled steel tank, externally wound condenser for maximum safety and hygiene. > Maximum temperature equal to 62°C obtained from renewable energy with heat pump only or by electric resistance (up to 75°C). > Digital interface with programmable TOUCH keys. > Integration via Solar Thermal (LT-S model) or via Electric Resistance (up to 75°C) on all models. > Integration with the Solar Photovoltaic system. INCENTIVES... when saving is a must. EGEA exploits all the features and technology of air-to-water heat pumps for the production of domestic hot water. Only 25% of the The system's energy requirement comes from electricity. FERROLI is at your disposal for technical and documentary support to take advantage of the incentives provided by the Ministerial Decree 02/16/2016) and subsequent extensions and amendments. ELECTRONICS... easier than that! The EGEA user interface features a very simple and intuitive display. > White backlit LEDs for temperature and function management. > Red backlit LEDs for alarm warnings. > The 4 side TOUCH buttons allow EGEA to be switched on/off ( ); navigation in the MENU ( ) and the increase ( + ) or decrease ( - ) of the setting values. INTEGRATION... EGEA gets along with everyone All versions of EGEA provide for the possibility of using renewable energy supplied by a photovoltaic system (electricity) or by a solar thermal system (thermal energy). The latter solution is possible ONLY for the 200 LT-S and 260 LT-S versions, whose tank houses a dedicated coil as solar exchanger. The use of this auxiliary energy source is activated and set via dedicated commands directly by the user. PHOTOVOLTAIC SYSTEM EGEA is able to manage the surplus Electricity supplied by a Photovoltaic System through the signaling of the Inverter through a clean contact. In this mode, EGEA will prepare domestic hot water at a higher (settable) temperature Set Point than the ECO/AUTO modes, thus allowing you to exploit the free energy available. But for those who want more .. . The EGEA heat pump water heaters have a WiFi module integrated into the product as standard so that they can be connected to the home WiFi network (WiFi router) and therefore be controlled via the APP. By downloading the dedicated EGEA SMART App for free, you can fully manage EGEA at any time Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Ferroli SKY ECO 11F Low NOx gas water heater complete with methane fume kit - NEW ERP Class (Class G - A) A XL load profile Nominal heat input Max kW 21.7 Thermal power Max / Min kW 19.5 / 5.5 Maximum working pressure 10 bar Maximum DHW production Δt 25°C / Δt 30°C l/min 11.2 / 9.3 Power supply V/Hz 230 / 50; 14 Kgs New Ferroli ECO range EFFECTIVE The ECO range has been designed according to the stringent efficiency parameters of the European ErP Directive. In practice, they are able to produce a lot of hot water at a low cost, respecting the environment and with minimal polluting emissions. They can also be integrated into a solar thermal system with extreme simplicity for maximum efficiency and comfort. EASY ECO water heaters are extremely simple to install and are interchangeable with previous series. Although very compact in size, they have been designed and built in such a way as to have easy access to the internal components for easy maintenance. BEAUTIFUL AND SMART The designers of the ECO project have created a «friendly» aesthetic that can be easily integrated with the most diverse furnishing styles. The knob or button controls have been designed to be easy to use and immediately understood. All Ferroli gas water heaters are equipped with a user interface display. Sky ECO F Sealed chamber gas water heater, with modulating thermal power and electronic control of the. Combustion. LOW NOx fume emission and SUN EASY system for direct coupling to a solar thermal system SUN EASY Easy... Cheap... Brilliant The SKY ECO range has been designed to be easily integrated with thermal solar systems, with natural or forced circulation. The temperature of the water coming from the solar circuit is constantly monitored and the water heater burner is turned on only if it is not hot enough. To reach the desired temperature, SUN EASY allows considerable savings even during the coldest seasons, exploiting and integrating even the smallest solar contribution, otherwise lost. The heart of water heaters All ECO series water heaters comply with the very strict restrictions on the emission of fumes into the atmosphere, imposed by European regulations. The burners in the ECO range use a particular technology which consists in keeping the flame temperature very low, keeping the gas trains wet. This expedient makes it possible to go well below the limits imposed by the ErP directive which sets the NOx limit at the threshold of 56 mg/kWh. Copper exchanger Interface displays Continuous power modulation Methane / LPG / Propane air Solar systems Also outdoor installation in protected places Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

Overview GAS WATER HEATER FERROLI SKY 11F LPG, 2 - Forced draft sealed chamber water heaters, COMPLETE WITH FUME EXHAUST KIT. Technical specifications nominal heat input: 21.7 kW useful power: 19.2 kW hot water production: 11 l/min dimensions: 59.5 x 29.5 x 19.5 cm LPG version Main features SKY Strengths: Compact geometry heat exchanger made entirely of copper, consisting of a battery of five tubes connected in series, externally finned, external surface with anti-corrosion coating obtained with wet, toxic alumina lacquer ECS (Evolved Combustion System): Electronic control of combustion to guarantee optimal operation as the thermal load varies in the characteristics of the flue Prepared to work in conjunction with solar panel systems Place of installation: also for outdoors partially protected up to -5C as standard, up to -15C with the aid of the optional antifreeze heater kit Modulating thermal flow Advantages of SKY: High yields obtained thanks to high technology combined with maximum constructive rationality Compact size and lightweight Arrangement of the internal organs in such a way that everything is easily accessible from the front, so as to ensure the widest possible intervention agility by the Assistance Center Wide range of water temperature regulation Also certified for propane air operation (50% air - 50% G31 by means of a specific transformation to be requested from the authorized assistance center (max total price of 30 eur + VAT). Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

The conversion to LPG can be requested from an authorised Ferroli service centre, free of charge. Energy class A XL load profile Nominal heat output Max / Min kW 52 / 9,5 Thermal power Max / Min kW 45,2 / 8,6 NOx class (according to EN 15502) 6 Maximum operating pressure Max / Min bar 10 / 0,2 Sanitary production Δt 25°C Δt 30°C l/min 26 / 21.6 Power supply V/Hz 230 / 50 Degree of electrical protection IP X5 Dimensions HxWxD mm 572x394x180 External Low NOx gas wall-mounted water heater for outdoor installations without flue pipes   EXTERNO is an A3 type instantaneous gas water heater with frontal flue gas discharge and suitable for outdoor installation without flue gas evacuation ducts. The water heater is equipped with a combustion unit which, in combination with a LOW NOx micro-flame burner, guarantees polluting levels below the parameters imposed by the severe limitations of the European ErP directive. EXTERNO has been designed exclusively for outdoor installations such as on balconies, attics or dedicated shafts. The casing is made up of two IPX5D insulated printed shells and the water circuit inside the appliance is protected with electrical resistances, fitted as standard, and managed by the electronic board. These measures allow EXTERNO to function correctly up to extreme conditions of -20°C. All appliances are supplied as standard with a remote control (and 10-metre long connection cable) featuring a large interface display and simple control buttons, to make adjustments easy and intuitive. SOLAR FUNCTION All models in the EXTERNO range can be easily installed in combination with a solar thermal system for the production of domestic hot water. The hydraulic circuit with its components have been designed to operate even at high temperatures of the water exiting the panels. ECO FUNCTION Using the remote control, you can activate the ECO function. When operating in ECO mode, the EXTERNO water heater will automatically set the hot water outlet temperature to 42°C and a reduced power of approximately 75% of the nominal power. CHILD PROTECTION If the hot water temperature is set to a very high value, each time the water heater is turned OFF, the delivery temperature will automatically return to 48°C so that the next withdrawal takes place in complete safety. The EXTERNO water heater series does not have on-board controls. The control, setting and temperature adjustment functions of the ACS are delegated to a remote control supplied as standard, complete with connection cable. The interface display and control keys have been designed to make the use of the control as simple and intuitive as possible. In the event of an anomaly and/or malfunction of the water heater, the display indication is accompanied by an audible signal. Product Warranty All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less