icon Beretta Ciao At 25 Csi Condensing Boiler Complete With Methane Fume Exhaust Kit - New Erp | CaldaieMurali

Beretta Ciao At 25 Csi Condensing Boiler Complete With Methane Fume Exhaust Kit - New Erp

Description

NB: in the absence of the ciao at, the NEW CIAO AT 25 LN LOW NOX model will be sent

BERETTA CIAO AT 25 CSI CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP


  • Product code: 20113788

Characteristics:

  • Energy efficiency in heating: B
  • Energy efficiency Sanitary: A
  • Sanitary load profile: XL
  • Nominal heat input: 25 kW
  • Electric Power: 129W
  • Supply voltage/frequency: 230/50 Volt/Hz
  • Electrical protection degree: X5D ip
  • Dimensions HxWxD: 780 x 400 x 338 ; 40 Kg
  • Gas version available: METHANE

Warm-up exercise:

  • Maximum pressure and temperatures: 3/90 bar/°C
  • Heating temperature selection range: 40/80 °C
  • Pump: pump head available for the system: 266 m/bar
  • Expansion tank capacity: 8 l

Healthcare exercise:

  • Maximum pressure: 6 bars
  • Minimum pressure: 0.15 bar
  • Quantity of hot water with ∆t=25°C: 14.3 l/min
  • Minimum domestic water flow rate: 2 l/min
  • DHW temperature selection range: 37 - 60 °C

Beretta HELLO AT


Hi AT, ideal for replacement in systems with radiators. Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving.

High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger.

Management: The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function.

The Ciao AT technology makes use of the condensing exchanger which recovers the latent heat of the fumes, the same principle used by condensing boilers. The exchanger, located at the top left, is connected directly to the fan which pushes the fumes inside it, before they are definitively expelled. The difference in the temperature of the fumes between the ~140°C inlet and the ~65°C outlet of the condensing exchanger is indicative of the amount of heat recovered from them.


The return from the system first passes through the condensing exchanger which recovers the heat from the fumes, and then passes through the primary exchanger, where it receives the remaining heat in order to reach the required flow temperature. The water then recovers part of the heat from the fumes, which would otherwise be expelled into the atmosphere, thus giving rise to less waste and consequently greater savings for the user.


Outdoor installation: Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required.

Up to 17 meters of Ø 60 ducting with the Ciao AT boiler: With Ciao AT it is possible to comfortably duct even the most "difficult" flues thanks to the approval for Ø 60mm flue systems which is added to the traditional Ø 80 mm ducting flue system. The main 60mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power.

TECHNICAL FEATURES:

  • Specific for systems with radiators and radiators (at high temperature)
  • Condensing post exchanger in aluminum alloy
  • Possibility of outdoor installation with antifreeze heater kit (optional)
  • IPX5D electrical protection degree
  • Environmental Self-Regulation System (SARA)
  • Low consumption circulator 6 m (EEI≤0.20)
  • Hydraulic connections cover (optional)
  • Condensate collection neutralizer drawer kit (optional)
  • Template, hydraulic fittings, gas and sanitary taps (optional)
  • For gas conversion, contact authorized Beretta Technical Assistance Centres

Product Guarantee
All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Beretta Ciao At 25 Csi Condensing Boiler Complete With Methane Fume Exhaust Kit - New Erp

Product form

NB: in the absence of the ciao at, the NEW CIAO AT 25 LN LOW NOX model will be sent... Read more

€711,00 Incl. VAT

    Description

    NB: in the absence of the ciao at, the NEW CIAO AT 25 LN LOW NOX model will be sent

    BERETTA CIAO AT 25 CSI CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP


    • Product code: 20113788

    Characteristics:

    • Energy efficiency in heating: B
    • Energy efficiency Sanitary: A
    • Sanitary load profile: XL
    • Nominal heat input: 25 kW
    • Electric Power: 129W
    • Supply voltage/frequency: 230/50 Volt/Hz
    • Electrical protection degree: X5D ip
    • Dimensions HxWxD: 780 x 400 x 338 ; 40 Kg
    • Gas version available: METHANE

    Warm-up exercise:

    • Maximum pressure and temperatures: 3/90 bar/°C
    • Heating temperature selection range: 40/80 °C
    • Pump: pump head available for the system: 266 m/bar
    • Expansion tank capacity: 8 l

    Healthcare exercise:

    • Maximum pressure: 6 bars
    • Minimum pressure: 0.15 bar
    • Quantity of hot water with ∆t=25°C: 14.3 l/min
    • Minimum domestic water flow rate: 2 l/min
    • DHW temperature selection range: 37 - 60 °C

    Beretta HELLO AT


    Hi AT, ideal for replacement in systems with radiators. Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving.

    High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger.

    Management: The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function.

    The Ciao AT technology makes use of the condensing exchanger which recovers the latent heat of the fumes, the same principle used by condensing boilers. The exchanger, located at the top left, is connected directly to the fan which pushes the fumes inside it, before they are definitively expelled. The difference in the temperature of the fumes between the ~140°C inlet and the ~65°C outlet of the condensing exchanger is indicative of the amount of heat recovered from them.


    The return from the system first passes through the condensing exchanger which recovers the heat from the fumes, and then passes through the primary exchanger, where it receives the remaining heat in order to reach the required flow temperature. The water then recovers part of the heat from the fumes, which would otherwise be expelled into the atmosphere, thus giving rise to less waste and consequently greater savings for the user.


    Outdoor installation: Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required.

    Up to 17 meters of Ø 60 ducting with the Ciao AT boiler: With Ciao AT it is possible to comfortably duct even the most "difficult" flues thanks to the approval for Ø 60mm flue systems which is added to the traditional Ø 80 mm ducting flue system. The main 60mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power.

    TECHNICAL FEATURES:

    • Specific for systems with radiators and radiators (at high temperature)
    • Condensing post exchanger in aluminum alloy
    • Possibility of outdoor installation with antifreeze heater kit (optional)
    • IPX5D electrical protection degree
    • Environmental Self-Regulation System (SARA)
    • Low consumption circulator 6 m (EEI≤0.20)
    • Hydraulic connections cover (optional)
    • Condensate collection neutralizer drawer kit (optional)
    • Template, hydraulic fittings, gas and sanitary taps (optional)
    • For gas conversion, contact authorized Beretta Technical Assistance Centres

    Product Guarantee
    All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

    Data sheetData sheet
    • peso: 30.0 kg
    • classe energetica produzione acs: A
    • classe energetica riscaldamento: B
    • gas: Methane
    • marca: BERETTA
    • metri quadri : 150
    • modello: CALD_1908
    • potenza in kw: 25
    • potenza nominale: 25
    • superficie riscaldabile mq: 150
    Shipping detailsShipping details

    The order is processed according to the payment method chosen:

    for payments by CREDIT CARD, PAYPAL, MARK, the order is processed the same day. Orders placed before 2.00 pm will be managed on the same day. The BRT or GLS courier will collect the ordered goods from our warehouses the following morning.

    Subsequently, the courier assigns the shipment number (tracking number) and communicates the same to the customer via e-mail, allowing him to follow the delivery status and estimated times in real time on the brt.it or gls-grop.com website. 24-72 the courier will deliver the goods (excluding islands and disadvantaged areas) to the address indicated by the Customer at the time of order confirmation. Transport costs are charged to the customer and are calculated taking into account the volume and/or weight of the ordered item/s. However, product delivery times vary according to the requested item, payment methods and the delivery times chosen by the Customer, which is why the times indicated are merely indicative and cannot be considered binding for Decidiprezzo srl. Orders placed online are delivered throughout Italy, with the exception of Livigno, Campione d'Italia, Vatican City and the Republic of San Marino. In some periods of the year (summer period / Christmas period) the processing times could undergo changes compared to the standard ones declared above.

    NB: In the periods of July and August due to the high amount of orders, delivery times could be delayed

    Icon for coinShipping cost

    Shipping costs vary according to the weight of the order.

    Consult the tables with the weights for Italy and for the smaller islands and disadvantaged areas.

    Warranty detailsWarranty details

    Pursuant to art. 63 of the Consumer Code, the risk of loss and damage to the goods, for reasons not attributable to the seller, is transferred to the consumer when the latter, or a third party designated by him and other than the carrier, physically comes into possession of goods. However, the risk is transferred to the consumer as soon as the goods are delivered to the carrier. The Customer who at the time of purchase has decided to make use of the extra insurance service for the transport of the purchased goods, in the event that he finds anomalies at the time of delivery (packaging damaged or otherwise altered in the closing seals, damaged product or scratched, missing one or more packages ordered), must accept the product by writing on the document provided by the carrier: "WE ACCEPT WITH RESERVE" + description of the anomaly found. In fact, to enforce the insurance coverage it is not sufficient to note "ACCEPTED WITH RESERVE" or "ACCEPTED WITH SUBJECT TO INSPECTION", BUT the reason for the reservation must be explained in detail. If the package or the product should show visible damage, scratches or any other type of anomaly and the courier should refuse to affix a specific reserve, the goods must be refused and the incident reported immediately (and in any case in a timely manner) to the Customer Service of Decidiprice srl. In any case, without prejudice to the seller's obligations in terms of legal guarantee pursuant to articles 128 et seq. of the Consumer Code, Decidiprezzo srl will not be held responsible for any anomalies found in the state of the product, after delivery, if the Customer, in the presence of an anomaly, has accepted the package without making a specific reservation (in the corrected above). Any damage or anomalies must be reported to Customer Service by email to postvendita@climaconvenienza.it. The request must be forwarded no later than 8 calendar days from receipt of the goods. Any notification beyond the aforementioned terms will not be taken into consideration.

    Customer service detailsCustomer service details

    Our customer service department is dedicated to providing support to our customers with any problems or questions they may have before or after purchasing our products.

    Use the direct communication channel to speak to one of our operators, or send us an email to one of the addresses listed on the contact us page.

    Our customer service team is made up of highly trained professionals who are always ready to help customers solve any problem or answer any question quickly and efficiently. We are committed to ensuring maximum customer satisfaction and providing the highest quality after-sales service. So if you need any assistance, don't hesitate to contact us; we will be happy to help you in any way we can.

    Recensioni di CaldaieMurali.it

    Latest Products Viewed

    Login

    Forgot your password?

    Don't have an account yet?
    Create account