Technical features Dimensions External Diameter: 18 mm Thickness : 1mm Roll length : 50m Minimum Coating Thickness: 1.5 mm Burst Pressure: 24.93 MPa Working Pressure : 6.23 MPa Water Content: 0.201 l/m SMISOL® Gas Resistant and non-permeable It is the copper pipe produced according to the EN 1057 standard covered during production with a special sheath with a full (non-star) section in polyvinyl chloride (PVC) in compliance with the UNI 10823 standard. The properties of SMISOL®Gas in terms of melting point, resistance to fire and pressure, impermeability to gas and absolute sealing of brazing and joints, become indispensable in the case of domestic distribution of combustible gas, where safety guarantees are essential and obligatorily provided for by the technical standards and by the provisions of the law. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR) , the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection During production, it is subjected to a patented treatment of passivation and stabilization of the internal wall . The SMISOL®Gas copper pipe has a carbon residue C < 0.06 mg/dm2 , much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤ 0.20 mg/dm2 External Protection Coating in stabilized polyvinyl resin, tested and guaranteed. The coating protects against external attacks from building materials (e.g. quick-setting concrete) and against damage caused by impacts during transport to the construction site. It allows use in the field of underground pipes , as indicated by the same UNI 10823 standard: "the coating is obtained through extrusion, without welding, in continuous, externally and internally smooth, with uniform nominal thickness, adhering to the external wall of the copper pipe for its entire surface to guarantee the absence of residual air pockets and prevent them from slipping off”. It is tested online in order to guarantee the electrical insulation resistance which, as required by the UNI 10823 standard, must be equal to or greater than 100 MΩm2, furthermore it satisfies the requirements of the UNI 7129 regarding the omission of the installation of the required dielectric joint for underground sections with a length not exceeding 3 m Coating Features Coating in special stabilized PVC resin. Full section (non-stellar) according to UNI 10823. Minimum thickness coating thickness: 1.5 mm (continuously checked with laser gauge). Sheath produced with top quality virgin granulate. Excellent resistance to external chemical agents. Ink marking every metre. Electrical insulation resistance: ≥ 100 MΩm2 (UNI 10823) Fields of Use Distribution of liquid and gaseous fuels with particular reference to underground installation In compliance with and within the limits established by the regulations Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 14 mm Thickness : 0.8mm Roll length : 50m Minimum Coating Thickness: 6 mm Burst Pressure: 25.65 MPa Working Pressure : 6.41 MPa Water Content: 0.1208 l/m SMISOL® 8 Versatile and professional SCT, with the expansion of its production range to 0.8 mm thickness , aims to offer the market a product with the best possible quality/price ratio; ensuring ease of installation and technical performance, as well as total compliance with current standards. SMISOL®8 contains a copper tube with a special internal passivation treatment, which perfectly complies with the EN 1057 standard and is CE marked as required by EU Regulation 305/2011 . Even the new dimensional range of SMISOL ® 8 has the UNI-IGQ Quality mark , which guarantees its compliance with current legislation. Offering SCT pipes with the UNI-IGQ brand means providing your customers with a further added value given by the certainty of an independent and recognized quality brand Field of Use Hot and cold drinking water Heating Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 22 mm Thickness : 1mm Roll length : 25m Minimum Coating Thickness: 1.5 mm Burst Pressure: 20.40 MPa Working Pressure: 5.10 MPa Water Content: 0.314 l/m SMISOL® Gas Resistant and non-permeable It is the copper pipe produced according to the EN 1057 standard covered during production with a special sheath with a full (non-star) section in polyvinyl chloride (PVC) in compliance with the UNI 10823 standard. The properties of SMISOL®Gas in terms of melting point, resistance to fire and pressure, impermeability to gas and absolute sealing of brazing and joints, become indispensable in the case of domestic distribution of combustible gas, where safety guarantees are essential and obligatorily provided for by the technical standards and by the provisions of the law. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR) , the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection During production, it is subjected to a patented treatment of passivation and stabilization of the internal wall . The SMISOL®Gas copper pipe has a carbon residue C < 0.06 mg/dm2 , much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤ 0.20 mg/dm2 External Protection Coating in stabilized polyvinyl resin, tested and guaranteed. The coating protects against external attacks from building materials (e.g. quick-setting concrete) and against damage caused by impacts during transport to the construction site. It allows use in the field of underground pipes , as indicated by the same UNI 10823 standard: "the coating is obtained through extrusion, without welding, in continuous, externally and internally smooth, with uniform nominal thickness, adhering to the external wall of the copper pipe for its entire surface to guarantee the absence of residual air pockets and prevent them from slipping off”. It is tested online in order to guarantee the electrical insulation resistance which, as required by the UNI 10823 standard, must be equal to or greater than 100 MΩm2, furthermore it satisfies the requirements of the UNI 7129 regarding the omission of the installation of the required dielectric joint for underground sections with a length not exceeding 3 m Coating Features Coating in special stabilized PVC resin. Full section (non-stellar) according to UNI 10823. Minimum thickness coating thickness: 1.5 mm (continuously checked with laser gauge). Sheath produced with top quality virgin granulate. Excellent resistance to external chemical agents. Ink marking every metre. Electrical insulation resistance: ≥ 100 MΩm2 (UNI 10823) Fields of Use Distribution of liquid and gaseous fuels with particular reference to underground installation In compliance with and within the limits established by the regulations Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 12 mm Thickness : 1mm Roll length : 50m Minimum Coating Thickness: 1.5 mm Burst Pressure: 37.40 MPa Working Pressure : 9.35 MPa Water Content: 0.079 l/m SMISOL® Gas Resistant and non-permeable It is the copper pipe produced according to the EN 1057 standard covered during production with a special sheath with a full (non-star) section in polyvinyl chloride (PVC) in compliance with the UNI 10823 standard. The properties of SMISOL®Gas in terms of melting point, resistance to fire and pressure, impermeability to gas and absolute sealing of brazing and joints, become indispensable in the case of domestic distribution of combustible gas, where safety guarantees are essential and obligatorily provided for by the technical standards and by the provisions of the law. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR) , the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection During production, it is subjected to a patented treatment of passivation and stabilization of the internal wall . The SMISOL®Gas copper pipe has a carbon residue C < 0.06 mg/dm2 , much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤ 0.20 mg/dm2 External Protection Coating in stabilized polyvinyl resin, tested and guaranteed. The coating protects against external attacks from building materials (e.g. quick-setting concrete) and against damage caused by impacts during transport to the construction site. It allows use in the field of underground pipes , as indicated by the same UNI 10823 standard: "the coating is obtained through extrusion, without welding, in continuous, externally and internally smooth, with uniform nominal thickness, adhering to the external wall of the copper pipe for its entire surface to guarantee the absence of residual air pockets and prevent them from slipping off”. It is tested online in order to guarantee the electrical insulation resistance which, as required by the UNI 10823 standard, must be equal to or greater than 100 MΩm2, furthermore it satisfies the requirements of the UNI 7129 regarding the omission of the installation of the required dielectric joint for underground sections with a length not exceeding 3 m Coating Features Coating in special stabilized PVC resin. Full section (non-stellar) according to UNI 10823. Minimum thickness coating thickness: 1.5 mm (continuously checked with laser gauge). Sheath produced with top quality virgin granulate. Excellent resistance to external chemical agents. Ink marking every metre. Electrical insulation resistance: ≥ 100 MΩm2 (UNI 10823) Fields of Use Distribution of liquid and gaseous fuels with particular reference to underground installation In compliance with and within the limits established by the regulations Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 22 mm Thickness : 1mm External diameter of the tube: 32 mm Roll length : 25 m Burst Pressure: 20.40 MPa Working Pressure: 5.10 MPa Water Content: 0.314 l/m SMISOL® Tekgas Practical and Safe SMISOL® Tekgas is the copper pipe produced according to the EN 1057 standard, coated during production with a special low-density closed-cell structure polyethylene sheath, manufactured in the sizes required by UNI 7129. Thanks to the particularity of the coating, co-extruded continuously on the copper pipe, and in the presence of spacers wound in a helical direction with respect to the axis of the pipe, it is particularly suitable for the transport of liquid and gaseous fuels. Spacers ensure that the sheath has an internal diameter that is 10 mm larger than the external diameter of the pipe. This geometric peculiarity allows the pipe to be used for crossing walls and floors without adding an additional metal sheath in full compliance with UNI 7129-1 which states in point 4.4.1.5: "When crossing perimeter and external walls, bricks blocks, perforated bricks and prefabricated panels, the gas supply pipe must not have joints, with the exception of the inlet and outlet joints and must be protected with a gas-tight through sheath. The sheath can be indifferently metal or polymeric material, the sheath must have an internal diameter greater than 10 mm compared to the external diameter of the pipe. This pipe can be laid concealed even in critical situations where the walls contain cavities (for example perforated bricks) this is always possible thanks to the polymeric sheath that continuously wraps the copper pipe, during installation it is sufficient to drown SMISOL® Tekgas in 15 mm of cement mortar to comply with the provisions of UNI 7129-1 point 4.5.5.5 and point 4.5.5.6. The helical shape of the spacers ensures that the interspace between the pipe and the sheath remains constant even in the 90° bends, avoiding crushing, in this way in the event of a leak, the danger of the formation of gas pockets is avoided. The in-line coating process ensures high malleability, superior to similar products on the market. In order to preserve this exclusive feature, the rolls of SMISOL®Tekgas have a very large winding diameter which, with the characteristics already described, make them a practical and particularly professional product at the same time. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR) , the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection During production, it is subjected to a patented treatment of passivation and stabilization of the internal wall . SMISOL®Tekgas copper pipe has a carbon residue C < 0.06 mg/dm2, much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤ 0.20 mg/dm2 External Protection The low-density closed-cell polyethylene coating protects the pipe from attacks exerted from the outside by building materials (e.g. quick-setting cement) and from damage caused by knocks during transport to the construction site. It complies with the reg. CEE/UE 2037/2000 and has a fire behavior of class BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84) Folding With reference to the bending methods using a special tube bender, it should be noted that the matrices and counter matrices to be used can differ significantly according to the brand and model used. For any information and clarification, you can contact us on the toll-free number or e-mail address listed on the cover Coating Features Covered in closed cell low density polyethylene. Helically wound spacers. Air gap: 5 mm min. Excellent resistance to external chemical agents. Ink marking every metre. Class 1 non-flammable Behavior in fire: BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84) Fields of Use Distribution of liquid and gaseous fuels with particular reference to masonry structures where the use of non-metallic sheath pipes is necessary In compliance with and within the limits established by the regulations Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 14 mm Thickness : 1mm Roll length : 50m Minimum Coating Thickness: 10 mm Burst Pressure: 32.06 MPa Working Pressure : 8.01 MPa Water Content: 0.113 l/m SMISOL® Frio Fears neither heat nor cold It is the copper pipe produced according to the EN 12735-1 standard (and ASTM B 68/M), and is pre-insulated in closed cell expanded polyethylene of regular dimensions and uniformly distributed (UNI EN 14114). It is distributed in rolls, having the dimensions of the pipe diameter in millimeters. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The thickness of the sheath is also sized in such a way as to satisfy the multiple needs of this application sector. In consideration of the particular specificity of the field of use, special attention is paid to the external protective film in polyethylene aimed at preventing the formation of condensation on the external wall of the product. Inner surface The internal surface of the copper tube is shiny, clean and dry , fundamental characteristics of a product normally available on the market for industrial use. This peculiarity allows to obtain an integrated system with the terminal elements of the system. The particular internal cleanliness of SMISOL® Frio is safeguarded by closing the ends of each roll with caps, directly during production. External Protection Covering in closed cell expanded polyethylene with an average value of the resistance factor to the diffusion of water vapor "µ" greater than 15000 . The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFC and HCFC, gases harmful to health and the environment and has a fire behavior class BL-s1-d0 according to EN 13501-1. Coating Features Thermal conductivity : λ ≤0.040 W/m°C. Average value of the resistance factor to the diffusion of water vapor "µ" greater than 15000. Average density of the coating: 33 kg/m3. Free from ammonia residues. Excellent resistance to external chemical agents. Non flammable class BL-s1-d0 according to EN 13501-1 Free from CFC and HCFC (Reg. CEE/UE 2037/2000) Directions For Design To avoid possible condensation phenomena on the pipe, it is necessary to check the environmental conditions in which the product is installed: relative humidity of the environment, temperature of the environment and of the fluid inside the pipe. In this regard, verification through the Psychrometric diagram is recommended Fields of Use Refrigeration. Transport of heat transfer liquids for multifunctional systems Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 12 mm Thickness : 1.0mm Roll length : 50m Minimum Coating Thickness: 6 mm Burst Pressure: 37.40 MPa Working Pressure : 9.35 MPa Water Content: 0.079 l/m SMISOL®One Versatile and professional It is the copper pipe produced according to the EN 1057 standard, pre-insulated during production with expanded polyethylene with a closed cell structure of regular and uniformly distributed dimensions. The insulating sheath is also externally protected by a special polyethylene film. Insulated according to Law 10/91 and relative implementation decree (DPR412/93), for the distribution of the heat transfer fluid inside heated rooms . The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The production process ensures the absolute adherence of the insulating sheath to the external wall of the copper pipe, so as to avoid the formation of cavities which have a negative effect on the thermal insulation capacity. The production process of the pipe, coated directly in line, guarantees the absolute malleability of the product and ease of installation. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR), the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection It has proven bacteriostatic properties , which make it the ideal material for water-sanitary networks, in order to prevent bacterial proliferation such as Legionellosis. SMISOL® One complies with DM174/04 (GU 166 of 17/07/04) which defines the conditions which materials in contact with drinking water must meet. During production, it is subjected to a patented passivation and stabilization treatment of the internal wall which makes it absolutely reliable in compliance with the potability parameters established by the European legislation on transported potable water (European Directive 98/83 and DL 31/ 01). It has a carbon residue C <0.06 mg/dm2, much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤0.20 mg/dm2 External Protection The insulating sheath is in closed-cell expanded PE in compliance with EEC/EU Reg. 2037/2000 (without the use of CFC and HCFC) with an external green polyethylene film and corrugated surface. The cladding has class BL-s1-d0 fire behavior according to EN 13501-1 Coating Features Thermal conductivity : λ ≤0.040 W/m°C. Average density of the coating: 30 kg/m3 Minimum thickness of the coating: 6 mm (9 mm for the diameter 22 x 1 mm) continuously controlled with laser gauge. Free from ammonia residues. Excellent resistance to external chemical agents Non flammable class BL-s1-d0 according to EN 13501-1 Free from CFC and HCFC (Reg. CEE/UE 2037/2000) Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 12 mm Thickness : 1mm Roll length : 50m Minimum Coating Thickness: 10 mm Burst Pressure: 37.40 MPa Working Pressure : 9.35 MPa Water Content: 0.079 l/m SMISOL® Frio Fears neither heat nor cold It is the copper pipe produced according to the EN 12735-1 standard (and ASTM B 68/M), and is pre-insulated in closed cell expanded polyethylene of regular dimensions and uniformly distributed (UNI EN 14114). It is distributed in rolls, having the dimensions of the pipe diameter in millimeters. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The thickness of the sheath is also sized in such a way as to satisfy the multiple needs of this application sector. In consideration of the particular specificity of the field of use, special attention is paid to the external protective film in polyethylene aimed at preventing the formation of condensation on the external wall of the product. Inner surface The internal surface of the copper tube is shiny, clean and dry , fundamental characteristics of a product normally available on the market for industrial use. This peculiarity allows to obtain an integrated system with the terminal elements of the system. The particular internal cleanliness of SMISOL® Frio is safeguarded by closing the ends of each roll with caps, directly during production. External Protection Covering in closed cell expanded polyethylene with an average value of the resistance factor to the diffusion of water vapor "µ" greater than 15000 . The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFC and HCFC, gases harmful to health and the environment and has a fire behavior class BL-s1-d0 according to EN 13501-1. Coating Features Thermal conductivity : λ ≤0.040 W/m°C. Average value of the resistance factor to the diffusion of water vapor "µ" greater than 15000. Average density of the coating: 33 kg/m3. Free from ammonia residues. Excellent resistance to external chemical agents. Non flammable class BL-s1-d0 according to EN 13501-1 Free from CFC and HCFC (Reg. CEE/UE 2037/2000) Directions For Design To avoid possible condensation phenomena on the pipe, it is necessary to check the environmental conditions in which the product is installed: relative humidity of the environment, temperature of the environment and of the fluid inside the pipe. In this regard, verification through the Psychrometric diagram is recommended Fields of Use Refrigeration. Transport of heat transfer liquids for multifunctional systems Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 12 mm Thickness : 1mm External diameter of the tube: 24 mm Roll length : 50m Burst Pressure: 37.40 MPa Working Pressure : 9.35 MPa Water Content: 0.079 l/m SMISOL® Tekgas Practical and Safe SMISOL® Tekgas is the copper pipe produced according to the EN 1057 standard, coated during production with a special low-density closed-cell structure polyethylene sheath, manufactured in the sizes required by UNI 7129. Thanks to the particularity of the coating, co-extruded continuously on the copper pipe, and in the presence of spacers wound in a helical direction with respect to the axis of the pipe, it is particularly suitable for the transport of liquid and gaseous fuels. Spacers ensure that the sheath has an internal diameter that is 10 mm larger than the external diameter of the pipe. This geometric peculiarity allows the pipe to be used for crossing walls and floors without adding an additional metal sheath in full compliance with UNI 7129-1 which states in point 4.4.1.5: "When crossing perimeter and external walls, bricks blocks, perforated bricks and prefabricated panels, the gas supply pipe must not have joints, with the exception of the inlet and outlet joints and must be protected with a gas-tight through sheath. The sheath can be indifferently metal or polymeric material, the sheath must have an internal diameter greater than 10 mm compared to the external diameter of the pipe. This pipe can be laid concealed even in critical situations where the walls contain cavities (for example perforated bricks) this is always possible thanks to the polymeric sheath that continuously wraps the copper pipe, during installation it is sufficient to drown SMISOL® Tekgas in 15 mm of cement mortar to comply with the provisions of UNI 7129-1 point 4.5.5.5 and point 4.5.5.6. The helical shape of the spacers ensures that the interspace between the pipe and the sheath remains constant even in the 90° bends, avoiding crushing, in this way in the event of a leak, the danger of the formation of gas pockets is avoided. The in-line coating process ensures high malleability, superior to similar products on the market. In order to preserve this exclusive feature, the rolls of SMISOL®Tekgas have a very large winding diameter which, with the characteristics already described, make them a practical and particularly professional product at the same time. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR) , the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection During production, it is subjected to a patented treatment of passivation and stabilization of the internal wall . SMISOL®Tekgas copper pipe has a carbon residue C < 0.06 mg/dm2, much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤ 0.20 mg/dm2 External Protection The low-density closed-cell polyethylene coating protects the pipe from attacks exerted from the outside by building materials (e.g. quick-setting cement) and from damage caused by knocks during transport to the construction site. It complies with the reg. CEE/UE 2037/2000 and has a fire behavior of class BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84) Folding With reference to the bending methods using a special tube bender, it should be noted that the matrices and counter matrices to be used can differ significantly according to the brand and model used. For any information and clarification, you can contact us on the toll-free number or e-mail address listed on the cover Coating Features Covered in closed cell low density polyethylene. Helically wound spacers. Air gap: 5 mm min. Excellent resistance to external chemical agents. Ink marking every metre. Class 1 non-flammable Behavior in fire: BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84) Fields of Use Distribution of liquid and gaseous fuels with particular reference to masonry structures where the use of non-metallic sheath pipes is necessary In compliance with and within the limits established by the regulations Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Dimensions External Diameter: 12 mm Thickness : 0.8mm Roll length : 50m Minimum Coating Thickness: 6 mm Burst Pressure: 29.92 MPa Working Pressure : 7.48 MPa Water Content: 0.0849 l/m SMISOL® 8 Versatile and professional SCT, with the expansion of its production range to 0.8 mm thickness , aims to offer the market a product with the best possible quality/price ratio; ensuring ease of installation and technical performance, as well as total compliance with current standards. SMISOL®8 contains a copper tube with a special internal passivation treatment, which perfectly complies with the EN 1057 standard and is CE marked as required by EU Regulation 305/2011 . Even the new dimensional range of SMISOL ® 8 has the UNI-IGQ Quality mark , which guarantees its compliance with current legislation. Offering SCT pipes with the UNI-IGQ brand means providing your customers with a further added value given by the certainty of an independent and recognized quality brand Field of Use Hot and cold drinking water Heating Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical Features Dimensions External Diameter: 10 mm Thickness: 1.0mm Roll Length: 50m Minimum Coating Thickness: 6 mm Burst Pressure : 44.88MPa Working Pressure : 11.22MPa Water content: 0.050 l/m SMISOL®One Versatile and professional It is the copper tube produced according to the EN 1057 standard, pre-insulated during production with expanded polyethylene with a closed cell structure of regular and uniformly distributed dimensions. The insulating sheath is also protected externally by a special polyethylene film. Insulated according to Law 10/91 and related implementing decree (DPR412/93), for the distribution of the heat transfer fluid inside heated environments . The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The production process ensures the absolute adhesion of the insulating sheath to the external wall of the copper tube, so as to avoid the formation of cavities that negatively affect the thermal insulation capacity. The production process of the tube, coated directly in line, guarantees the absolute malleability of the product and ease of installation. Furthermore, to protect the end consumer, in compliance with EU Regulation 305/2011 for construction products (CPR), the EN1057-compliant copper tubes produced by SCT are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ Quality mark Internal Protection It has proven bacteriostatic properties , which make it the ideal material for water-sanitary networks, in order to prevent bacterial proliferation such as Legionellosis. SMISOL® One complies with DM174/04 (GU 166 of 17/07/04) which defines the conditions to which materials in contact with drinking water must respond. It is subjected, during the production phase, to a patented passivation and stabilization treatment of the internal wall which makes it absolutely reliable in compliance with the drinkability parameters set by the European legislation on transported drinking water (European Directive 98/83 and DL 31/01). It has a carbon residue C <0.06 mg/dm2, much lower than that set by the EN 1057 standard, which establishes a carbon content C ≤0.20 mg/dm2 External Protection The insulating sheath is made of closed-cell expanded PE compliant with Reg. EEC/EU 2037/2000 (without the use of CFC and HCFC) with an external film in green polyethylene and corrugated on the surface. The coating has a fire behaviour of class BL-s1-d0 according to EN 13501-1 Coating Features Thermal conductivity: λ ≤0.040 W/m°C. Average coating density: 30 kg/m3 Min. coating thickness: 6 mm (9 mm for diameter 22 x 1 mm) continuously monitored with laser gauge. Free from ammonia residues. Excellent resistance to external chemical agents Non-flammable class BL-s1-d0 according to EN 13501-1 Free from CFCs and HCFCs (Reg. EEC/EU 2037/2000) Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical Features Dimensions External Diameter: 16 mm Thickness: 1mm Roll Length: 50m Minimum Coating Thickness: 10 mm Burst Pressure : 28.05MPa Working Pressure : 7.01MPa Water content: 0.154 l/m SMISOL® Frio Fears neither the Heat nor the Cold It is the copper tube produced according to the EN 12735-1 standard (and ASTM B 68/M), and is pre-insulated in closed-cell expanded polyethylene of regular and uniformly distributed dimensions (UNI EN 14114). It is distributed in rolls, having the dimensions of the diameter of the tube in millimetres. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The thickness of the sheath is also sized in such a way as to satisfy the multiple needs of this application sector. In consideration of the particular specificity of the field of use, special attention is paid to the external protective polyethylene film aimed at preventing the formation of condensation on the external wall of the product. Internal Surface The internal surface of the copper tube is shiny, clean and dry , fundamental characteristics of a product normally available on the market for industrial use. This peculiarity allows to obtain an integrated system with the terminal elements of the plant. The particular internal cleanliness of SMISOL® Frio is safeguarded by closing the ends of each roll with caps, directly during the production phase. External Protection Closed-cell expanded polyethylene coating with an average value of the water vapour diffusion resistance factor “µ” greater than 15000. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment and has a fire behaviour of class BL-s1-d0 according to EN 13501-1. Coating Features Thermal conductivity: λ ≤0.040 W/m°C. Average value of the water vapour diffusion resistance factor “µ” greater than 15000. Average coating density: 33 kg/m3. Free from ammonia residues. Excellent resistance to external chemical agents. Non-flammable class BL-s1-d0 according to EN 13501-1 Free from CFCs and HCFCs (Reg. EEC/EU 2037/2000) Design Guidelines To avoid possible condensation phenomena on the pipe, it is necessary to check the environmental conditions in which the product is installed: relative humidity of the environment, temperature of the environment and of the fluid inside the pipe. In this regard, it is recommended to check using the Psychrometric chart Fields of Use Refrigeration. Transport of heat transfer fluids for multifunctional systems Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less