Check out our large selection of tubing and insulation to fit your plumbing and thermal system needs. Find high-quality pipes for drinking water, heating and air conditioning, along with insulation materials to reduce heat losses.
Pipes and Insulation
SCTubes Multilayer Copper Pipe Scubes Insulated Layer For Heating 25 Meters 32 X 3 Mm Coated With Copper Core
Technical features Dimensions External Diameter: 32 mm Thickness : 3mm Roll length : 25m Coating Thickness : 9 mm Operating pressure : 23 bar Water Content: 0.531 l/m Minimum Bending Radius with Bending Machine: 128 mm Minimum Manual Bending Radius: 192 mm Technical characteristics of the tube Internal Contact Material: Copper Cu-DHP (Cu:99.9% min. P: 0.015 ÷ 0.040%) according to DM 174/04 (Regulation concerning materials in contact with drinking water) Inner surface roughness: 1.5 μm Outer layer : PE-RT Maximum Operating Temperature: 95 °C continuously Breaking load: R. min. ≥ 220 Mpa (N/mm2 ) Percent elongation: (A5 min.) : 40% Technical Characteristics Of Insulation Insulating material : Closed-cell expanded cross-linked polyethylene (PE-X). Thermal conductivity of the insulation (λ) : 0.039 W/mK Average density of the insulation : 30 kg/m3 Resistance to water vapor diffusion (μ) : > 9000 Behavior in fire : Class 1 (DM 26/06/84) Resistance to chemical agents : Very Good (ASTM 543-56 T) Acoustic absorption : ~60% (DIN 4109 300-2500Hz) SMISOL® Strato To give you more we put our soul into it A noble, safe, performing, tested, hygienic, bacteriostatic core, a copper core. Strato represents the evolution of pipes for the transport of drinking water and for heating radiators. A product that combines the lightness and ease of installation of traditional multilayer with the unique performance of copper pipes in terms of resistance to pressure and high temperatures, hygiene and bacteriostatic properties, low pressure drops and reduced internal roughness . Strato is manufactured according to the UNI 11342 standard: "Seamless copper and polyethylene composite pipes for fluid adduction", it is obtained through the co-extrusion of a specific reduced thickness copper pipe with an indissoluble polyethylene layer. It is then externally insulated with an insulating covering in closed cell expanded polyethylene in compliance with Law 10/91, implementing decree DPR 412/93 and subsequent updates. The quality of the raw material used and the characteristics of the coating make the product particularly suitable for the distribution of drinking water (in compliance with DM 174/04) and for heating systems with high temperature radiators. Ease of installation and bending, absence of memory effect , lightness, excellent quality/price ratio , wide choice of fittings to combine, reliability and safety, make Strato the truly innovative solution among the latest generation pipes for plumbing and sanitary uses. Fields of Use Drinking water distribution Radiator heating Chilled water distribution In compliance with and within the limits established by the regulations Advantages Resistance to pressure and high temperatures : Strato is not afraid of sudden increases in pressure, since its metallic nature gives it very high mechanical resistance Hygiene and bacteriostatic : It is totally hygienic and fights bacterial proliferation. It complies with DM 174/04: drinking water comes into contact only with the copper surface, guaranteeing the absence of odors and flavors Absence of welds: The copper tube contained inside is obtained through a continuous drawing process, unlike traditional multilayers which involve the longitudinal union of the aluminum layer through different technologies Total impermeability and 100% barrier to oxygen: Its metal core makes it impermeable to gases: there is no risk of leaks and/or contamination from inside to outside and vice versa. In heating systems, the presence of oxygen which can attack boilers, pump impellers or other metal parts is avoided Flexibility and workability: Strato can be bent by hand even with reduced bending radii and does not undergo any memory effect, maintaining the acquired shape Low linear thermal expansion coefficient: Unlike plastic pipes, thermal expansion is extremely limited, thus guaranteeing dimensional stability even when the temperature of the fluid transported varies Low pressure drops: Strato has an extremely low internal roughness (1.5μm compared to 7μm of traditional multilayers). This means lower load losses and a lower tendency to suffer limescale deposits Junction Technology Strato is compatible with all fittings produced according to the EN 1254-8 standard normally used with multilayer pipes. The peculiarity of Strato is that of offering an "open" solution and therefore not being bound to any specific connection. Different combinations are available, compatible with the most important brands of fittings on the market, including full bore ones. The latter solution makes it possible to adopt smaller pipe sections, with savings both in terms of pipe cost and masonry work. Different types of mechanical fittings can be used (press, quick fit, tighten) Installation Cut to Size : Cutting, calibration and deburring can be performed with accessories commonly on the market. Bending : The Strato tube can be easily bent by hand or with a normal copper tube bender. Junction : Different types of mechanical fittings (press fit, quick fit, compression) available on the market can be used. Coating Features Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€440,00
-
SCTubes Multilayer Copper Pipe Scubes Insulated Layer For Heating 50 Meters 16 X 2 Mm Coated With Copper Core
Technical Features Dimensions External Diameter: 16 mm Thickness: 2mm Roll Length: 50m Coating Thickness : 6mm Operating Pressure: 32 bar Water content: 0.113 l/m Minimum Bending Radius with Bending Machine: 64 mm Minimum Manual Bending Radius: 96 mm Technical Features of the Tube Internal Contact Material: Cu-DHP Copper (Cu:99.9% min. P: 0.015 ÷ 0.040%) according to DM 174/04 (Regulation concerning materials in contact with drinking water) Inner surface roughness: 1.5 μm Outer layer: PE-RT Maximum Operating Temperature: 95°C continuous Unit load at break: R. min. ≥ 220 Mpa (N/mm2) Percentage elongation: (A5 min.) : 40% Technical Characteristics of Insulation Insulating material: Closed-cell expanded cross-linked polyethylene (PE-X) Thermal conductivity of the insulation (λ): 0.039 W/mK Average density of insulation: 30 kg/m3 Resistance to water vapour diffusion (μ): > 9000 Fire behaviour: Class 1 (DM 26/06/84) Chemical Resistance : Very Good (ASTM 543-56 T) Sound absorption: ~60% (DIN 4109 300-2500Hz) SMISOL® Layer To give you more we put our heart and soul into it A noble, safe, high-performance, tested, hygienic, bacteriostatic soul, a Copper soul. Strato represents the evolution of pipes for the transport of drinking water and for radiator heating. A product that combines the lightness and ease of installation of traditional multilayer with the unique performance of copper pipes in terms of resistance to pressure and high temperatures, hygiene and bacteriostaticity, low pressure drops and reduced internal roughness . Strato is manufactured according to the UNI 11342 standard: "Seamless composite copper and polyethylene pipes for fluid supply", obtained through the coextrusion of a specific reduced thickness copper pipe with an indissoluble polyethylene layer. It is then insulated externally with an insulating coating of closed-cell expanded polyethylene compliant with Law 10/91, implementing decree DPR 412/93 and subsequent updates. The quality of the raw material used and the characteristics of the coating make the product particularly suitable for the distribution of drinking water (in compliance with DM 174/04) and for high-temperature radiator heating systems. Ease of installation and bending, absence of memory effect , lightness, excellent quality/price ratio , wide choice of fittings to match, reliability and safety, make Strato the truly innovative solution among the latest generation of pipes for hydrothermal sanitary uses. Fields of Use Drinking water distribution Radiator heating Chilled water distribution In compliance with and within the limits set by the regulations Advantages Resistance to pressure and high temperatures: Strato does not fear sudden increases in pressure, since its metallic nature gives it very high mechanical resistance. Hygiene and bacteriostaticity: It is totally hygienic and fights bacterial proliferation. It complies with DM 174/04: drinking water comes into contact only with the copper surface, guaranteeing the absence of odors and flavors No welding: The copper tube contained inside is obtained through a continuous drawing process, unlike traditional multilayers which involve the longitudinal union of the aluminium layer through different technologies. Total impermeability and 100% oxygen barrier: Its metal core makes it impermeable to gases: there is no risk of leaks and/or contamination from the inside to the outside and vice versa. In heating systems, the presence of oxygen that can attack boilers, pump impellers or other metal parts is avoided Flexibility and workability: Strato can be bent by hand even with small bending radii and does not undergo any memory effect, maintaining the acquired shape. Low linear thermal expansion coefficient: Unlike plastic pipes, thermal expansion is extremely limited, thus ensuring dimensional stability even when the temperature of the transported fluid varies Low pressure drops: Strato has an extremely low internal roughness (1.5μm compared to 7μm of traditional multilayers). This means lower pressure drops and a lower tendency to suffer from limescale encrustations. Joining Technology Strato is compatible with all fittings produced according to the EN 1254-8 standard normally used with multilayer pipes. The peculiarity of Strato is that it offers an “open” solution and therefore is not tied to any specific fitting. Different combinations are available, compatible with the most important brands of fittings on the market, including those with full bore. This last solution allows the use of smaller pipe sections, with a saving both in terms of the cost of the pipe and of masonry work. Different types of mechanical fittings can be used (press-fit, quick-fit, tightening) Installation Cutting to Size : Cutting, calibrating and deburring can be performed with commonly available accessories. Bending : Strato tube can be easily bent by hand or with a standard copper tube bender. Joint : Different types of mechanical fittings (press-fit, quick-fit, compression) available on the market can be used. Coating Features Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.
€200,00
-
SCTubes Multilayer Copper Pipe Scubes Insulated Layer For Heating 50 Meters 20 X 2 Mm Coated With Copper Core
Technical features Dimensions External Diameter: 20 mm Thickness : 2mm Roll length : 50m Coating Thickness : 6 mm Operating Pressure : 25 bar Water Content: 0.201 l/m Minimum Bending Radius with Bending Machine: 80 mm Minimum Manual Bending Radius: 120 mm Technical characteristics of the tube Internal Contact Material: Copper Cu-DHP (Cu:99.9% min. P: 0.015 ÷ 0.040%) according to DM 174/04 (Regulation concerning materials in contact with drinking water) Inner surface roughness: 1.5 μm Outer layer : PE-RT Maximum Operating Temperature: 95 °C continuously Breaking load: R. min. ≥ 220 Mpa (N/mm2 ) Percent elongation: (A5 min.) : 40% Technical Characteristics Of Insulation Insulating material : Closed-cell expanded cross-linked polyethylene (PE-X). Thermal conductivity of the insulation (λ) : 0.039 W/mK Average density of the insulation : 30 kg/m3 Resistance to water vapor diffusion (μ) : > 9000 Behavior in fire : Class 1 (DM 26/06/84) Resistance to chemical agents : Very Good (ASTM 543-56 T) Acoustic absorption : ~60% (DIN 4109 300-2500Hz) SMISOL® Strato To give you more we put our soul into it A noble, safe, performing, tested, hygienic, bacteriostatic core, a copper core. Strato represents the evolution of pipes for the transport of drinking water and for heating radiators. A product that combines the lightness and ease of installation of traditional multilayer with the unique performance of copper pipes in terms of resistance to pressure and high temperatures, hygiene and bacteriostatic properties, low pressure drops and reduced internal roughness . Strato is manufactured according to the UNI 11342 standard: "Seamless copper and polyethylene composite pipes for fluid adduction", it is obtained through the co-extrusion of a specific reduced thickness copper pipe with an indissoluble polyethylene layer. It is then externally insulated with an insulating covering in closed cell expanded polyethylene in compliance with Law 10/91, implementing decree DPR 412/93 and subsequent updates. The quality of the raw material used and the characteristics of the coating make the product particularly suitable for the distribution of drinking water (in compliance with DM 174/04) and for heating systems with high temperature radiators. Ease of installation and bending, absence of memory effect , lightness, excellent quality/price ratio , wide choice of fittings to combine, reliability and safety, make Strato the truly innovative solution among the latest generation pipes for plumbing and sanitary uses. Fields of Use Drinking water distribution Radiator heating Chilled water distribution In compliance with and within the limits established by the regulations Advantages Resistance to pressure and high temperatures : Strato is not afraid of sudden increases in pressure, since its metallic nature gives it very high mechanical resistance Hygiene and bacteriostatic : It is totally hygienic and fights bacterial proliferation. It complies with DM 174/04: drinking water comes into contact only with the copper surface, guaranteeing the absence of odors and flavors Absence of welds: The copper tube contained inside is obtained through a continuous drawing process, unlike traditional multilayers which involve the longitudinal union of the aluminum layer through different technologies Total impermeability and 100% barrier to oxygen: Its metal core makes it impermeable to gases: there is no risk of leaks and/or contamination from inside to outside and vice versa. In heating systems, the presence of oxygen which can attack boilers, pump impellers or other metal parts is avoided Flexibility and workability: Strato can be bent by hand even with reduced bending radii and does not undergo any memory effect, maintaining the acquired shape Low linear thermal expansion coefficient: Unlike plastic pipes, thermal expansion is extremely limited, thus guaranteeing dimensional stability even when the temperature of the fluid transported varies Low pressure drops: Strato has an extremely low internal roughness (1.5μm compared to 7μm of traditional multilayers). This means lower load losses and a lower tendency to suffer limescale deposits Junction Technology Strato is compatible with all fittings produced according to the EN 1254-8 standard normally used with multilayer pipes. The peculiarity of Strato is that of offering an "open" solution and therefore not being bound to any specific connection. Different combinations are available, compatible with the most important brands of fittings on the market, including full bore ones. The latter solution makes it possible to adopt smaller pipe sections, with savings both in terms of pipe cost and masonry work. Different types of mechanical fittings can be used (press, quick fit, tighten) Installation Cut to Size : Cutting, calibration and deburring can be performed with accessories commonly on the market. Bending : The Strato tube can be easily bent by hand or with a normal copper tube bender. Junction : Different types of mechanical fittings (press fit, quick fit, compression) available on the market can be used. Coating Features Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€355,00
-
SCTubes Multilayer Copper Pipe Scubes Insulated Layer For Heating 25 Meters 26 X 3 Mm Coated With Copper Core
Technical features Dimensions External Diameter: 26 mm Thickness : 3mm Roll length : 25m Coating Thickness : 9 mm Operating Pressure : 25 bar Water Content: 0.314 l/m Minimum Bending Radius with Bending Machine: 104 mm Minimum Manual Bending Radius: 156 mm Technical characteristics of the tube Internal Contact Material: Copper Cu-DHP (Cu:99.9% min. P: 0.015 ÷ 0.040%) according to DM 174/04 (Regulation concerning materials in contact with drinking water) Inner surface roughness: 1.5 μm Outer layer : PE-RT Maximum Operating Temperature: 95 °C continuously Breaking load: R. min. ≥ 220 Mpa (N/mm2 ) Percent elongation: (A5 min.) : 40% Technical Characteristics Of Insulation Insulating material : Closed-cell expanded cross-linked polyethylene (PE-X). Thermal conductivity of the insulation (λ) : 0.039 W/mK Average density of the insulation : 30 kg/m3 Resistance to water vapor diffusion (μ) : > 9000 Behavior in fire : Class 1 (DM 26/06/84) Resistance to chemical agents : Very Good (ASTM 543-56 T) Acoustic absorption : ~60% (DIN 4109 300-2500Hz) SMISOL® Strato To give you more we put our soul into it A noble, safe, performing, tested, hygienic, bacteriostatic core, a copper core. Strato represents the evolution of pipes for the transport of drinking water and for heating radiators. A product that combines the lightness and ease of installation of traditional multilayer with the unique performance of copper pipes in terms of resistance to pressure and high temperatures, hygiene and bacteriostatic properties, low pressure drops and reduced internal roughness . Strato is manufactured according to the UNI 11342 standard: "Seamless copper and polyethylene composite pipes for fluid adduction", it is obtained through the co-extrusion of a specific reduced thickness copper pipe with an indissoluble polyethylene layer. It is then externally insulated with an insulating covering in closed cell expanded polyethylene in compliance with Law 10/91, implementing decree DPR 412/93 and subsequent updates. The quality of the raw material used and the characteristics of the coating make the product particularly suitable for the distribution of drinking water (in compliance with DM 174/04) and for heating systems with high temperature radiators. Ease of installation and bending, absence of memory effect , lightness, excellent quality/price ratio , wide choice of fittings to combine, reliability and safety, make Strato the truly innovative solution among the latest generation pipes for plumbing and sanitary uses. Fields of Use Drinking water distribution Radiator heating Chilled water distribution In compliance with and within the limits established by the regulations Advantages Resistance to pressure and high temperatures : Strato is not afraid of sudden increases in pressure, since its metallic nature gives it very high mechanical resistance Hygiene and bacteriostatic : It is totally hygienic and fights bacterial proliferation. It complies with DM 174/04: drinking water comes into contact only with the copper surface, guaranteeing the absence of odors and flavors Absence of welds: The copper tube contained inside is obtained through a continuous drawing process, unlike traditional multilayers which involve the longitudinal union of the aluminum layer through different technologies Total impermeability and 100% barrier to oxygen: Its metal core makes it impermeable to gases: there is no risk of leaks and/or contamination from inside to outside and vice versa. In heating systems, the presence of oxygen which can attack boilers, pump impellers or other metal parts is avoided Flexibility and workability: Strato can be bent by hand even with reduced bending radii and does not undergo any memory effect, maintaining the acquired shape Low linear thermal expansion coefficient: Unlike plastic pipes, thermal expansion is extremely limited, thus guaranteeing dimensional stability even when the temperature of the fluid transported varies Low pressure drops: Strato has an extremely low internal roughness (1.5μm compared to 7μm of traditional multilayers). This means lower load losses and a lower tendency to suffer limescale deposits Junction Technology Strato is compatible with all fittings produced according to the EN 1254-8 standard normally used with multilayer pipes. The peculiarity of Strato is that of offering an "open" solution and therefore not being bound to any specific connection. Different combinations are available, compatible with the most important brands of fittings on the market, including full bore ones. The latter solution makes it possible to adopt smaller pipe sections, with savings both in terms of pipe cost and masonry work. Different types of mechanical fittings can be used (press, quick fit, tighten) Installation Cut to Size : Cutting, calibration and deburring can be performed with accessories commonly on the market. Bending : The Strato tube can be easily bent by hand or with a normal copper tube bender. Junction : Different types of mechanical fittings (press fit, quick fit, compression) available on the market can be used. Coating Features Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€325,00
-
SCTubes Multilayer Copper Pipe Scubes Insulated Layer For Heating 50 Meters 14 X 2 Mm Coated With Copper Core
Technical features Dimensions External Diameter: 14 mm Thickness : 2mm Roll length : 50m Coating Thickness : 6 mm Operating Pressure : 35 bar Water Content: 0.079 l/m Minimum Bending Radius with Bending Machine: 56 mm Minimum Manual Bending Radius: 84 mm Technical characteristics of the tube Internal Contact Material: Copper Cu-DHP (Cu:99.9% min. P: 0.015 ÷ 0.040%) according to DM 174/04 (Regulation concerning materials in contact with drinking water) Inner surface roughness: 1.5 μm Outer layer : PE-RT Maximum Operating Temperature: 95 °C continuously Breaking load: R. min. ≥ 220 Mpa (N/mm2 ) Percent elongation: (A5 min.) : 40% Technical Characteristics Of Insulation Insulating material : Closed-cell expanded cross-linked polyethylene (PE-X). Thermal conductivity of the insulation (λ) : 0.039 W/mK Average density of the insulation : 30 kg/m3 Resistance to water vapor diffusion (μ) : > 9000 Behavior in fire : Class 1 (DM 26/06/84) Resistance to chemical agents : Very Good (ASTM 543-56 T) Acoustic absorption : ~60% (DIN 4109 300-2500Hz) SMISOL® Strato To give you more we put our soul into it A noble, safe, performing, tested, hygienic, bacteriostatic core, a copper core. Strato represents the evolution of pipes for the transport of drinking water and for heating radiators. A product that combines the lightness and ease of installation of traditional multilayer with the unique performance of copper pipes in terms of resistance to pressure and high temperatures, hygiene and bacteriostatic properties, low pressure drops and reduced internal roughness . Strato is manufactured according to the UNI 11342 standard: "Seamless copper and polyethylene composite pipes for fluid adduction", it is obtained through the co-extrusion of a specific reduced thickness copper pipe with an indissoluble polyethylene layer. It is then externally insulated with an insulating covering in closed cell expanded polyethylene in compliance with Law 10/91, implementing decree DPR 412/93 and subsequent updates. The quality of the raw material used and the characteristics of the coating make the product particularly suitable for the distribution of drinking water (in compliance with DM 174/04) and for heating systems with high temperature radiators. Ease of installation and bending, absence of memory effect , lightness, excellent quality/price ratio , wide choice of fittings to combine, reliability and safety, make Strato the truly innovative solution among the latest generation pipes for plumbing and sanitary uses. Fields of Use Drinking water distribution Radiator heating Chilled water distribution In compliance with and within the limits established by the regulations Advantages Resistance to pressure and high temperatures : Strato is not afraid of sudden increases in pressure, since its metallic nature gives it very high mechanical resistance Hygiene and bacteriostatic : It is totally hygienic and fights bacterial proliferation. It complies with DM 174/04: drinking water comes into contact only with the copper surface, guaranteeing the absence of odors and flavors Absence of welds: The copper tube contained inside is obtained through a continuous drawing process, unlike traditional multilayers which involve the longitudinal union of the aluminum layer through different technologies Total impermeability and 100% barrier to oxygen: Its metal core makes it impermeable to gases: there is no risk of leaks and/or contamination from inside to outside and vice versa. In heating systems, the presence of oxygen which can attack boilers, pump impellers or other metal parts is avoided Flexibility and workability: Strato can be bent by hand even with reduced bending radii and does not undergo any memory effect, maintaining the acquired shape Low linear thermal expansion coefficient: Unlike plastic pipes, thermal expansion is extremely limited, thus guaranteeing dimensional stability even when the temperature of the fluid transported varies Low pressure drops: Strato has an extremely low internal roughness (1.5μm compared to 7μm of traditional multilayers). This means lower load losses and a lower tendency to suffer limescale deposits Junction Technology Strato is compatible with all fittings produced according to the EN 1254-8 standard normally used with multilayer pipes. The peculiarity of Strato is that of offering an "open" solution and therefore not being bound to any specific connection. Different combinations are available, compatible with the most important brands of fittings on the market, including full bore ones. The latter solution makes it possible to adopt smaller pipe sections, with savings both in terms of pipe cost and masonry work. Different types of mechanical fittings can be used (press, quick fit, tighten) Installation Cut to Size : Cutting, calibration and deburring can be performed with accessories commonly on the market. Bending : The Strato tube can be easily bent by hand or with a normal copper tube bender. Junction : Different types of mechanical fittings (press fit, quick fit, compression) available on the market can be used. Coating Features Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€170,00
-
SCTubes Copper Pipe Smisol One Sctubes For Heating 50 Meters 12x1 Mm Coated In Expanded Polyethylene
Technical features Dimensions External Diameter: 12 mm Thickness : 1.0mm Roll length : 50m Minimum Coating Thickness: 6 mm Burst Pressure: 37.40 MPa Working Pressure : 9.35 MPa Water Content: 0.079 l/m SMISOL®One Versatile and professional It is the copper pipe produced according to the EN 1057 standard, pre-insulated during production with expanded polyethylene with a closed cell structure of regular and uniformly distributed dimensions. The insulating sheath is also externally protected by a special polyethylene film. Insulated according to Law 10/91 and relative implementation decree (DPR412/93), for the distribution of the heat transfer fluid inside heated rooms . The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The production process ensures the absolute adherence of the insulating sheath to the external wall of the copper pipe, so as to avoid the formation of cavities which have a negative effect on the thermal insulation capacity. The production process of the pipe, coated directly in line, guarantees the absolute malleability of the product and ease of installation. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR), the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection It has proven bacteriostatic properties , which make it the ideal material for water-sanitary networks, in order to prevent bacterial proliferation such as Legionellosis. SMISOL® One complies with DM174/04 (GU 166 of 17/07/04) which defines the conditions which materials in contact with drinking water must meet. During production, it is subjected to a patented passivation and stabilization treatment of the internal wall which makes it absolutely reliable in compliance with the potability parameters established by the European legislation on transported potable water (European Directive 98/83 and DL 31/ 01). It has a carbon residue C <0.06 mg/dm2, much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤0.20 mg/dm2 External Protection The insulating sheath is in closed-cell expanded PE in compliance with EEC/EU Reg. 2037/2000 (without the use of CFC and HCFC) with an external green polyethylene film and corrugated surface. The cladding has class BL-s1-d0 fire behavior according to EN 13501-1 Coating Features Thermal conductivity : λ ≤0.040 W/m°C. Average density of the coating: 30 kg/m3 Minimum thickness of the coating: 6 mm (9 mm for the diameter 22 x 1 mm) continuously controlled with laser gauge. Free from ammonia residues. Excellent resistance to external chemical agents Non flammable class BL-s1-d0 according to EN 13501-1 Free from CFC and HCFC (Reg. CEE/UE 2037/2000) Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€305,00
-
SCTubes Smisol Frio Copper Pipe Smisol Frio For Chilled Water 50 Meters 12 X 1 Mm Coated In Polyethylene
Technical features Dimensions External Diameter: 12 mm Thickness : 1mm Roll length : 50m Minimum Coating Thickness: 10 mm Burst Pressure: 37.40 MPa Working Pressure : 9.35 MPa Water Content: 0.079 l/m SMISOL® Frio Fears neither heat nor cold It is the copper pipe produced according to the EN 12735-1 standard (and ASTM B 68/M), and is pre-insulated in closed cell expanded polyethylene of regular dimensions and uniformly distributed (UNI EN 14114). It is distributed in rolls, having the dimensions of the pipe diameter in millimeters. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The thickness of the sheath is also sized in such a way as to satisfy the multiple needs of this application sector. In consideration of the particular specificity of the field of use, special attention is paid to the external protective film in polyethylene aimed at preventing the formation of condensation on the external wall of the product. Inner surface The internal surface of the copper tube is shiny, clean and dry , fundamental characteristics of a product normally available on the market for industrial use. This peculiarity allows to obtain an integrated system with the terminal elements of the system. The particular internal cleanliness of SMISOL® Frio is safeguarded by closing the ends of each roll with caps, directly during production. External Protection Covering in closed cell expanded polyethylene with an average value of the resistance factor to the diffusion of water vapor "µ" greater than 15000 . The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which imposes the use of expanded insulating sheaths without the use of CFC and HCFC, gases harmful to health and the environment and has a fire behavior class BL-s1-d0 according to EN 13501-1. Coating Features Thermal conductivity : λ ≤0.040 W/m°C. Average value of the resistance factor to the diffusion of water vapor "µ" greater than 15000. Average density of the coating: 33 kg/m3. Free from ammonia residues. Excellent resistance to external chemical agents. Non flammable class BL-s1-d0 according to EN 13501-1 Free from CFC and HCFC (Reg. CEE/UE 2037/2000) Directions For Design To avoid possible condensation phenomena on the pipe, it is necessary to check the environmental conditions in which the product is installed: relative humidity of the environment, temperature of the environment and of the fluid inside the pipe. In this regard, verification through the Psychrometric diagram is recommended Fields of Use Refrigeration. Transport of heat transfer liquids for multifunctional systems Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€410,00
-
SCTubes Smisol Tekgas Copper Pipe Smisol Tekgas For Distribution Of Liquid And Gaseous Fuels 50 Meters 12 X 1 Mm Coated In High Density Polyethylene
Technical features Dimensions External Diameter: 12 mm Thickness : 1mm External diameter of the tube: 24 mm Roll length : 50m Burst Pressure: 37.40 MPa Working Pressure : 9.35 MPa Water Content: 0.079 l/m SMISOL® Tekgas Practical and Safe SMISOL® Tekgas is the copper pipe produced according to the EN 1057 standard, coated during production with a special low-density closed-cell structure polyethylene sheath, manufactured in the sizes required by UNI 7129. Thanks to the particularity of the coating, co-extruded continuously on the copper pipe, and in the presence of spacers wound in a helical direction with respect to the axis of the pipe, it is particularly suitable for the transport of liquid and gaseous fuels. Spacers ensure that the sheath has an internal diameter that is 10 mm larger than the external diameter of the pipe. This geometric peculiarity allows the pipe to be used for crossing walls and floors without adding an additional metal sheath in full compliance with UNI 7129-1 which states in point 4.4.1.5: "When crossing perimeter and external walls, bricks blocks, perforated bricks and prefabricated panels, the gas supply pipe must not have joints, with the exception of the inlet and outlet joints and must be protected with a gas-tight through sheath. The sheath can be indifferently metal or polymeric material, the sheath must have an internal diameter greater than 10 mm compared to the external diameter of the pipe. This pipe can be laid concealed even in critical situations where the walls contain cavities (for example perforated bricks) this is always possible thanks to the polymeric sheath that continuously wraps the copper pipe, during installation it is sufficient to drown SMISOL® Tekgas in 15 mm of cement mortar to comply with the provisions of UNI 7129-1 point 4.5.5.5 and point 4.5.5.6. The helical shape of the spacers ensures that the interspace between the pipe and the sheath remains constant even in the 90° bends, avoiding crushing, in this way in the event of a leak, the danger of the formation of gas pockets is avoided. The in-line coating process ensures high malleability, superior to similar products on the market. In order to preserve this exclusive feature, the rolls of SMISOL®Tekgas have a very large winding diameter which, with the characteristics already described, make them a practical and particularly professional product at the same time. Furthermore, to protect the final consumer, in compliance with EU Regulation 305/2011 for construction products (CPR) , the copper pipes manufactured by SCT according to EN1057 are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ quality mark Internal Protection During production, it is subjected to a patented treatment of passivation and stabilization of the internal wall . SMISOL®Tekgas copper pipe has a carbon residue C < 0.06 mg/dm2, much lower than that required by the EN 1057 standard, which establishes a carbon content C ≤ 0.20 mg/dm2 External Protection The low-density closed-cell polyethylene coating protects the pipe from attacks exerted from the outside by building materials (e.g. quick-setting cement) and from damage caused by knocks during transport to the construction site. It complies with the reg. CEE/UE 2037/2000 and has a fire behavior of class BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84) Folding With reference to the bending methods using a special tube bender, it should be noted that the matrices and counter matrices to be used can differ significantly according to the brand and model used. For any information and clarification, you can contact us on the toll-free number or e-mail address listed on the cover Coating Features Covered in closed cell low density polyethylene. Helically wound spacers. Air gap: 5 mm min. Excellent resistance to external chemical agents. Ink marking every metre. Class 1 non-flammable Behavior in fire: BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84) Fields of Use Distribution of liquid and gaseous fuels with particular reference to masonry structures where the use of non-metallic sheath pipes is necessary In compliance with and within the limits established by the regulations Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€350,00
-
SCTubes Copper Pipe Smisol 8 Scubes For Heating 50 Meters 12 X 0.8 Mm Coated In Expanded Polyethylene
Technical features Dimensions External Diameter: 12 mm Thickness : 0.8mm Roll length : 50m Minimum Coating Thickness: 6 mm Burst Pressure: 29.92 MPa Working Pressure : 7.48 MPa Water Content: 0.0849 l/m SMISOL® 8 Versatile and professional SCT, with the expansion of its production range to 0.8 mm thickness , aims to offer the market a product with the best possible quality/price ratio; ensuring ease of installation and technical performance, as well as total compliance with current standards. SMISOL®8 contains a copper tube with a special internal passivation treatment, which perfectly complies with the EN 1057 standard and is CE marked as required by EU Regulation 305/2011 . Even the new dimensional range of SMISOL ® 8 has the UNI-IGQ Quality mark , which guarantees its compliance with current legislation. Offering SCT pipes with the UNI-IGQ brand means providing your customers with a further added value given by the certainty of an independent and recognized quality brand Field of Use Hot and cold drinking water Heating Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€270,00
-
SCTubes Copper Pipe Smisol One Sctubes For Heating 50 Meters 10x1 Mm Coated In Expanded Polyethylene
Technical Features Dimensions External Diameter: 10 mm Thickness: 1.0mm Roll Length: 50m Minimum Coating Thickness: 6 mm Burst Pressure : 44.88MPa Working Pressure : 11.22MPa Water content: 0.050 l/m SMISOL®One Versatile and professional It is the copper tube produced according to the EN 1057 standard, pre-insulated during production with expanded polyethylene with a closed cell structure of regular and uniformly distributed dimensions. The insulating sheath is also protected externally by a special polyethylene film. Insulated according to Law 10/91 and related implementing decree (DPR412/93), for the distribution of the heat transfer fluid inside heated environments . The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The production process ensures the absolute adhesion of the insulating sheath to the external wall of the copper tube, so as to avoid the formation of cavities that negatively affect the thermal insulation capacity. The production process of the tube, coated directly in line, guarantees the absolute malleability of the product and ease of installation. Furthermore, to protect the end consumer, in compliance with EU Regulation 305/2011 for construction products (CPR), the EN1057-compliant copper tubes produced by SCT are marked with the CE mark . A further guarantee of compliance with current legislation is given by obtaining the UNI-IGQ Quality mark Internal Protection It has proven bacteriostatic properties , which make it the ideal material for water-sanitary networks, in order to prevent bacterial proliferation such as Legionellosis. SMISOL® One complies with DM174/04 (GU 166 of 17/07/04) which defines the conditions to which materials in contact with drinking water must respond. It is subjected, during the production phase, to a patented passivation and stabilization treatment of the internal wall which makes it absolutely reliable in compliance with the drinkability parameters set by the European legislation on transported drinking water (European Directive 98/83 and DL 31/01). It has a carbon residue C <0.06 mg/dm2, much lower than that set by the EN 1057 standard, which establishes a carbon content C ≤0.20 mg/dm2 External Protection The insulating sheath is made of closed-cell expanded PE compliant with Reg. EEC/EU 2037/2000 (without the use of CFC and HCFC) with an external film in green polyethylene and corrugated on the surface. The coating has a fire behaviour of class BL-s1-d0 according to EN 13501-1 Coating Features Thermal conductivity: λ ≤0.040 W/m°C. Average coating density: 30 kg/m3 Min. coating thickness: 6 mm (9 mm for diameter 22 x 1 mm) continuously monitored with laser gauge. Free from ammonia residues. Excellent resistance to external chemical agents Non-flammable class BL-s1-d0 according to EN 13501-1 Free from CFCs and HCFCs (Reg. EEC/EU 2037/2000) Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.
€270,00
-
SCTubes Smisol Frio Copper Pipe Smisol Frio For Chilled Water 50 Meters 16 X 1 Mm Coated In Polyethylene
Technical Features Dimensions External Diameter: 16 mm Thickness: 1mm Roll Length: 50m Minimum Coating Thickness: 10 mm Burst Pressure : 28.05MPa Working Pressure : 7.01MPa Water content: 0.154 l/m SMISOL® Frio Fears neither the Heat nor the Cold It is the copper tube produced according to the EN 12735-1 standard (and ASTM B 68/M), and is pre-insulated in closed-cell expanded polyethylene of regular and uniformly distributed dimensions (UNI EN 14114). It is distributed in rolls, having the dimensions of the diameter of the tube in millimetres. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The thickness of the sheath is also sized in such a way as to satisfy the multiple needs of this application sector. In consideration of the particular specificity of the field of use, special attention is paid to the external protective polyethylene film aimed at preventing the formation of condensation on the external wall of the product. Internal Surface The internal surface of the copper tube is shiny, clean and dry , fundamental characteristics of a product normally available on the market for industrial use. This peculiarity allows to obtain an integrated system with the terminal elements of the plant. The particular internal cleanliness of SMISOL® Frio is safeguarded by closing the ends of each roll with caps, directly during the production phase. External Protection Closed-cell expanded polyethylene coating with an average value of the water vapour diffusion resistance factor “µ” greater than 15000. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment and has a fire behaviour of class BL-s1-d0 according to EN 13501-1. Coating Features Thermal conductivity: λ ≤0.040 W/m°C. Average value of the water vapour diffusion resistance factor “µ” greater than 15000. Average coating density: 33 kg/m3. Free from ammonia residues. Excellent resistance to external chemical agents. Non-flammable class BL-s1-d0 according to EN 13501-1 Free from CFCs and HCFCs (Reg. EEC/EU 2037/2000) Design Guidelines To avoid possible condensation phenomena on the pipe, it is necessary to check the environmental conditions in which the product is installed: relative humidity of the environment, temperature of the environment and of the fluid inside the pipe. In this regard, it is recommended to check using the Psychrometric chart Fields of Use Refrigeration. Transport of heat transfer fluids for multifunctional systems Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.
€545,00
SCTubes Copper Tube Smisol Clim Platinum For Air Conditioning 50 Meters Thickness 0.8 Mm With Diameter 1/4 - 3/8 - 1/2 1/4"
Technical Features Dimensions External Diameter: 6.35mm (1/4") - 9.52mm (3/8") - 12.70mm (1/2) Thickness: 0.8mm Roll Length: 50m From : External Diameter Sp : Thickness Minimum Coating Thickness Minimum Coating Thickness 1/4 : 6 mm Minimum Coating Thickness 3/8 : 8 mm Minimum Coating Thickness 1/2 : 10 mm Burst Pressure Burst Pressure 1/4 : 56.54MPa Burst Pressure 3/8 : 37.71 MPa Burst Pressure 1/2 : 28.27MPa Operating Pressure Working Pressure 1/4 : 14.14MPa Working Pressure 3/8 : 9.43MPa Working Pressure 1/2 : 7.07 MPa Water Content Water content 1/4 : 0.018 l/m Water content 3/8 : 0.049 l/m Water content 1/2 : 0.097 l/m SMISOL®Clim Platinum The climate specialist It is the copper tube produced according to the EN 12735-1 standard, and is pre-insulated in closed-cell expanded polyethylene of regular and uniformly distributed dimensions (UNI EN 14114). It is distributed in rolls. The diameter of the copper tube, as required by the EN 12735-1 standard, is expressed in inches. The insulating sheath is produced in full compliance with the European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment. The thickness of the sheath is also sized in such a way as to satisfy the multiple needs of this application sector. In consideration of the particular specificity of the field of use, special attention is paid to the external protective polyethylene film aimed at preventing the formation of condensation on the external wall of the product. SMISOL®Clim Platinum also stands out for its particularly low eccentricity values, a very important feature for the flaring operation. Internal Surface The internal surface of the copper tube is shiny, clean and dry , fundamental characteristics of a product normally available on the market for industrial use. This peculiarity allows to obtain an integrated system with the terminal elements of the system. The particular internal cleanliness of SMISOL®Clim Platinum is safeguarded by closing the ends of each roll with caps, directly during the production phase. Coating Features Thermal conductivity: l≤ 0.040 W/m°C Average value of the water vapour diffusion resistance factor “μ” > 15,000 Average coating density: 30 kg/m 3 Free from ammonia residues Excellent resistance to external chemical agents Non-flammable class 1 (DM 26/06/84) Fire behaviour: BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84) Free from CFCs and HCFCs (Reg. EEC/EU 2037/2000) Pigmentation of the outer film “Silver grey” Increased resistance to UV rays Halogen-free flame retardant Fields of Use Conditioning Transport of refrigerant gases. (R32, R410A, R407,...) In compliance with and within the limits set by the regulations. External Protection Closed-cell expanded polyethylene coating with an average value of the water vapor diffusion resistance factor “μ” greater than 15,000 . The insulating sheath is produced in full compliance with European Regulation EEC/EU 2037/2000 which requires the use of expanded insulating sheaths without the use of CFCs and HCFCs, gases harmful to health and the environment and has a fire behavior of class BLs1d0 (EN 13501-1) and class 1 (DM 26/06/84). The external polyethylene film contains a darker pigment than the traditional white in order to counteract the crystallization process of the PE. Furthermore, the normal anti-UV additives have an antagonistic effect on the flame retardant necessary for the product. In order to avoid this inconvenience, the SMISOL®Clim Platinum sheath contains an ecological halogen-free flame retardant that does not counteract the anti-UV action. Tests carried out according to the ASTM G-155 standard (accelerated aging) demonstrate that SMISOL®Clim Platinum is suitable for areas with strong annual solar radiation . At the end of the exposure test, the sample did not show any symptoms of degradation. Accelerated Aging Test The test involves a duration of 4,000 hours of exposure in a weatherometer with a CI65 Xenon lamp, which is equivalent in Kly to approximately 3 years of continuous exposure in Northern Italy or 2 years in Southern Italy. Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.
€140,00 - €275,00
