ATTENTION THE BOILER IS BORN WITH METHANE. SO THE TRANSFORMATION KIT IS REQUIRED. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE VAILLANT ecoTEC PRO CONDENSING VMW 286/5-3+ COMPLETE WITH FUME EXHAUST KIT -ErP Technical features For heating and domestic hot water production Forced draft sealed chamber Nominal thermal power 24.0 kW ErP energy class (Heating and DHW): Class A DHW nominal heat input 28.6 kW Nominal heat input in heating mode 24.5 kW Water content in the generator 2.2 l Expansion vessel capacity 10 l Domestic hot water production (ΔT = 30K) 13.4 lt Dimensions (hxpxl) mm 720 x 338 x 440 ; 36kg Version: LPG (WITH SPECIAL TRANSFORMATION KIT) General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. EcoTEC PRO The wall mounted boiler that offers the right balance between performance and comfort. The ecoTEC pro VMW (heating and DHW production) are available in power ratings of 19 and 24 kW. ecoTEC pro was born as the natural evolution of Vaillant's consolidated technology and experience in condensing technology. ecoTEC pro has been designed to offer the right balance between performance and comfort both in heating and in the production of domestic hot water. Its simplicity of regulation makes it the ideal boiler for all users. ecoTEC pro is equipped with an extremely simple interface with plain text and backlit display. The small dimensions of ecoTEC pro VMW 70cm high, 44cm wide and 35cm deep (identical to the previous version) allow installation in any environment. A new high-efficiency pump and new electronics allow ecoTEC pro to consume very little electricity, guaranteeing considerable savings throughout the year. Instant DHW production Intuitive user interface Simplicity of management ****Efficiency in heating Modulation 1:5 Modulating pump (Class A) Steel primary exchanger 10 l expansion vessel transfer kit from methane to propane or propane air code 0020160884 Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Open Chamber Boiler Beretta CIAO LX 24 CAI Low NOx LPG 20151437 - NEW Technical features Model: CIAO LX 24 CAI gpl Code: 20151437 Heating/DHW nominal heat input: 26.70 kW Heating/DHW nominal thermal power: 24.06 kW Efficiency at nominal power: 90.1 Efficiency at reduced load (30%): 89.2% NOx class 6 Maximum working pressure heating bar 3 Maximum absorbed electrical power W 47 Quantity of hot water deltaT 25C° 13.8 l/min Dimensions HxWxD 740x400x340 HELLO LX Beretta has renewed the Ciao open flue boiler; the previous model Ciao S CAI now becomes Ciao LX CAI and is placed in Class NOX 6 . Aesthetically it looks like the previous one but its technology is now completely different. The Ciao LX CAI is the entry-level model for approaching Beretta boiler technology; the CAI model has an open chamber and natural draft. The adjectives that identify it are: high quality standard, sturdiness, reliability and economy in purchasing and running. The innovative Double Exchanger is very compact and is of the plate type with the possibility of preheating . It also uses a low consumption Synchronous Circulator (EEI=0.20) with anti-block cycle system and 3-way valve; it is equipped with a smoke control thermostat and by-pass on the heating circuit. Beretta Ciao has a simple, modern and elegant line; the front panel, the real brain of the boiler, is equipped with many functions. Ciao LX CAI is designed to be installed outdoors in partially protected places, thanks to the dedicated accessories and board antifreeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit together with the siphon antifreeze heater kit (optional to be requested separately from the Beretta Technical Assistance Centre). A convenient liquid crystal digital display for viewing the temperature and diagnostic codes, the on/off/summer/winter/reset/heating temperature/ Amico Climate System selector, the domestic hot water temperature selector/pre-heating activation, the Hydrometer. The wall water fittings, the sanitary taps and the gas tap are not included in the package. GUARANTEED SAVINGS AND HIGH COMFORT Gas consumption is always very low . This new version complies with the new standards on combustion gas emissions (NOx 6) e the ErP Directive 2015 ; the boiler benefits from Energy Classes C in Heating and B in Sanitary . It all starts with savings, starting from the purchase price up to consumption management. Maximum comfort with minimum cost. TECHNICAL FEATURES Class B/C NOx class 6 - ErP version, equipped with 6 m low consumption circulator Double exchanger: primary and sanitary plate with the possibility of preheating 8 liter expansion vessel Arrangement for climatic thermoregulation (optional external probe to be purchased through CAT) IPX5D electrical protection degree Optional plumbing fittings, gas and sanitary taps 3-way valve with anti-block cycle system Smoke control thermostat By-pass on the heating circuit Electronic board with self-diagnostic function and antifreeze protection Simple and intuitive digital display Selector on/off/summer/winter/reset/heating temperature/activation of the Clima Amico system Domestic hot water temperature selector/pre-heating activation Hydrometer Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Riello Open Chamber boiler mod. START 24 KI Low NOx - NEW ErP CODE 20151434 Product code: 20151434 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary energy efficiency profile XL Class B Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 26.7 kW Heating/DHW nominal heat output: 24 kW Energy efficiency (92/42/EEC) **** Useful efficiency Pn max - Pn min (80°-60°): 90.1-86.4% Profit return 30% (47th return): 89.2% Open chamber with natural draft NOx class: 6 Min/max heating operating pressure: 0.25-3 bar Max absorbed electric power: 47 W Expansion vessel: 8 litres Min/max pressure in DHW: 0.15-8 bar Quantity of hot water with Δt 25°C: 13.8 l/min Quantity of hot water at Δt 30°C: 11.5 l/min Quantity of hot water at Δt 35°C: 9.9 l/min Sanitary water temperature selection range: 37-60°C Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 740 x 400 x 332 ; 30 Kgs Electrical protection degree: IP X5D Power supply: METHANE Standard natural gas operation with possibility of conversion to LPG (G31), this modification is the responsibility of the installer or the technical assistance service START 24 KI LN (LOW NOx) Start LN is characterized by a modern design despite its essentiality and is ideal for heating and the production of domestic hot water in small and medium-sized domestic users. Start LN is available in power ratings of 24 and 28 kW with low NOx emissions <56 mg/kWh. Characteristics: Double exchanger: domestic hot water production with plate exchanger for greater resistance to the formation of limescale CTR system for more rapid achievement of the desired comfort and a reduction in consumption and temperature changes in the heating bodies 8 liter expansion vessel Low consumption circulator (IEE≤0.20) Antifreeze function which protects the heating and DHW circuits down to 0°C Standard thermoregulation on the boiler board in combination with the external probe (optional) Can be interfaced with the Remote Control Panel Hydraulic connections available as an accessory kit Standard natural gas operation with possibility of conversion to LPG (G31), this modification is the responsibility of the installer or the technical assistance service Electrical protection degree IP X5D Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: THE CURVE AND THE PIPE FOR THE COAXIAL KIT MUST BE PURCHASED SEPARATELY Momiji 24 kW Rinnai Condensing Boiler Complete with FUme Exhaust Kit with Integrated Wi-Fi Chronothermostat Code REB-KAI2024FF Heating energy class A XL load profile Nominal thermal power kW 20 EN677 efficiency on PCI (80-60°C) % 96.1 Nominal power modulation (80-60°C) Heating kW 6.7 - 19.5 NOx class 6 Maximum electric power absorbed in heating W 97 Electrical power in stand-by W < 3 Supply voltage V/Hz 230 / 50 Degree of protection IPX5D Domestic hot water delivery (ΔT=35°C) l/min 9.6 Domestic hot water delivery (ΔT=25°C) l/min 13.5 Dimensions (H x W x D) (mm)660x440x285 MOMIJGI The warm embrace of autumn MOMIJI are the red maple trees typical of the Orient, whose leaves color autumn red, a season that the Japanese experience as "comfort". Thanks to the mild climate and temperatures that are once again welcoming (no longer the torrid heat of summer, not yet the freezing climate of winter), taking time out is even more pleasant. Enjoying your home, as well as the foliage, gives well-being. Momiji best interprets the combination of traditional systems and condensing technology. In fact, while integrating perfectly with different systems, it is designed to optimize the condensation technology on radiator systems, responding concretely to the needs for savings and eco-sustainability of this type of heating, extremely widespread but often unable to fully exploit the advantages of condensation. The heating is smart Momiji offers the standard Wi-Fi chronothermostat (which can also be installed in a room other than that of the generator) to manage and control the boiler anytime, anywhere, in complete freedom. Consumption reports, weekly programming, modification of settings and management of multiple boilers (such as one's own and that of elderly parents, or the house in the mountains) from the same "My Rinnai" APP, available for Android and iOS smartphones. All this and much more to offer you totally smart management. The integrated climatic probe is a standard of Rinnai heat generators: the internal positioning allows you, who use it and you who install it, to avoid masonry work and electrical connections. Thanks to this sensor, you can forget about regulating the temperature in your home and let the generator take care of everything, intelligently adapting its operation according to the weather, more or less cold. So while the boiler operates in climatic regulation with sliding temperature, you can enjoy a perfect balance between comfort and savings, and no worries. Momiji Comfort has never been easier Easy, everywhere Like the Rinnai Infinity water heaters, the Momiji boilers are also specifically designed to facilitate the installer's work. The device is small, light and compact. It is ready to use and does not need to be configured. The flue system is split Ø80/80 and, thanks to the high prevalence of the fan, it is possible to reach up to 30 equivalent linear metres. Thermal exchange Momiji has a copper heat exchange, with a large passage section: this facilitates integration into existing radiator systems and simplifies cleaning operations. This range of boilers is the perfect solution for often imperfect traditional systems. Can also be installed outdoors Momiji is IPX5D certified and has the standard antifreeze kit up to -20°C. Thanks to these characteristics, it can also be installed outdoors without the need for additional protection Integrated condensate neutraliser The Momiji series features the condensate siphon integrated inside the generator, already added with granulate and immediately ready for use. This allows you to simplify installation, always, even when replacing a traditional high temperature generator. The integrated neutralizer, in fact, allows you to eliminate the acidity of the condensate (acidic pH water produced by the normal operation of the heat generator, corrosive for the pipes) without having to face the costs of purchasing and maintaining an external accessory that performs this function otherwise essential. Product Warranty: The warranty on this item is 24 months from the date of purchase.

Read more less

UNICAL X 24 C condensing boiler Low NOx 6 Complete with methane flue exhaust kit in stainless steel - ErP Technical data according to dir. ErP C24 Minimum/nominal useful power in condensing kW 5 ÷ 25.2 Seasonal heating energy efficiency ambient ηs % 91 Seasonal EFFICIENCY CLASS for heating Useful heat output in high temp. (Tr 60°C / tm 80°C) P4 kW 23.2 Efficiency at nominal thermal power in high temperature regime (Tr 60°C / Tm 80°C) η4 % 87.0 Useful power at 30% of rated thermal power in low temperature regime (Tr 30°C) P1 kW 7.7 Efficiency at 30% of nominal thermal power in low temperature regime (Tr 30°C) η1 % 96.1 Emissions of nitrogen oxides ref. PCS NO x mg/kWh 22 Declared load profile XL Sanitary seasonal EFFICIENCY CLASS Produc. DHW cont. Dt 25 K (mixed) l/min 13.2 Expansion vessel capacity l 10 Max condensate production kg/h 3.86 Heating circuit pressure (min/max) 0.5 / 3.0 bar DHW circuit pressure (min/max) bar 0.5 / 6.0 IP degree of protection X5D NO class x 6 Dimensions (HxWxD) mm 700x420x345 Net weight kg 34 x X like INOX, like the exchanger which is the engine of this wall-mounted condensing boiler. X is available in the instantaneous combined version (13.2 l/min), it runs on both methane and LPG (conversion kit supplied). Characteristics: Premix Low NOx burner (Class 6) IPX5D (also for outdoors) Compact dimensions and compatible with other Unical models (ideal for replacements) Template and unified connections (Unical KONm / KONe ) Minimum thermal power regulation in heating function Electronic antifreeze for operation down to -15 Management of 2 zones with differentiated priorities (high and low temperature) Electronics with HWS "Hot Water Speed" function to eliminate the delay in DHW production and automatic "air vent" function Layout conceived with large spaces for easy maintenance Wide choice of accessories including: - both modulating and on/off control thermostats - external probe for managing both the boiler and one or two high/low temperature zones STAINLESS STEEL EXCHANGER MONOSPIRAL WITH OVAL SECTION WITHOUT WELDING GREATER COMBUSTION VOLUME LESS EMISSIONS / HIGHER PERFORMANCE OPTIMIZED PRESSURE DROP REDUCTION OF DEPOSITS LESS NOISE LONGER DURATION OVER TIME FRONT ACCESS FOR EASY MAINTENANCE Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Technical features Model : Luna Duo-Tec E 24 + Magician Nominal heat input 24 kW DHW nominal heat input: 24.7 kW Nominal heating heat input: 20.6 kW Heating energy efficiency class: A DHW energy efficiency class: A Load profile : XL Auxiliary electricity consumption: 0.013 ~ 0.030 kW Rated Electric Power: 85W Minimum operating temperature: -5°C Expansion vessel capacity: 8 lire Heating circuit water temperature adjustment: 25° ~ 80° C Sanitary water temperature adjustment: 35° ~ 60° C Specific flow rate according to EN 13203-1 : 11.5 l/min Sanitary water production ∆T 25 : 13.8 l/min DHW circuit minimum water flow rate: 2 l/min Heating circuit water pressure: 0.5 ~ 8 bar Sound power level : 49 dB(A) Degree of Protection : IPX5D Maximum length Ø 60/100 concentric exhaust-intake pipe: 10 m Maximum length of Ø 80 split exhaust-intake pipe: 80 m Maximum flue gas temperature: 80° C Power supply: CNG / LPG Dimensions and weight Dimensions (HxWxD): 763x450x345 mm Weight : 38.5Kg Features Baxi Magician Model: Baxi Magician Maximum cable length for the Baxi Mago bus: 50 m Maximum cable resistance: 2 x 5 ohms Operating conditions : 0°C ~ 60°C Temperature control area : 10° ~ 30° C Dimensions (WxHxD): 120x90x27 mm Baxi Luna Duo-Tec boiler + Mago as standard The ideal condensation both for new buildings and for the replacement of an old generator Aesthetics can change, not performance The already well-known Baxi boilers are presented today with a renewed aesthetic , increasingly modern and attentive to new design trends, which allows them to be inserted in any living context The control panel has also been completely renewed and is equipped with a new backlit LCD display that is even clearer and simpler to use thanks to dedicated and independent keys The boilers, even more beautiful and modern thanks to the restyling , still keep intact the characteristics that have always distinguished the Duo-tec range Reliability Robustness, durability and reliable performance Efficiency and savings . The reduction of the on/off cycles translates into significant benefits in terms of energy savings and lower emissions Completeness of the range Models for heating only, with instantaneous DHW production, and also the compact version with the possibility of outdoor installation . The range has been further enriched with the new models equipped as standard with the Baxi Mago modulating chronothermostat with integrated WI-FI The ideal boiler for new builds and for replacement The Duo-tec E range of gas-fired condensing boilers has been specifically designed in compliance with the requirements of the Ecodesign and Labeling Directives, to make it particularly suitable both for new builds and for replacing an old generator . The energy class, identified by a letter, expresses a range of efficiency values ​​within which the one expressed by the product in question resides. The label was created for the final consumer, so that, through real and comparable data, he can make informed choices by targeting high-efficiency products Comfort management with Baxi Mago The Luna Duo-tec E 24/33 Mago and Duo-tec Compact E 24 Mago boilers are equipped AS STANDARD with the Baxi Mago, the modulating chronothermostat with integrated WI-FI designed to simplify the lives of installers, service centers and end users, as allows you to manage domestic comfort directly from an App , via the Wi-Fi connection. By downloading the dedicated App on your smartphone or tablet, it will be possible to connect to the Baxi Mago to control the temperature, manage programming, view the consumption graph, read any error messages, set the holiday mode, etc. An innovative tool with a unique design, which combines extreme practicality with a modern, captivating aesthetic with a strong appeal. The Duo-tec E range is compatible with the Baxi Mago available as an accessory , for remote boiler control Baxi Mago simplifies your life • Beautiful to look at and easy to use thanks to the comfortable rotary knob and the backlit color screen with large, easy-to-read numbers. Baxi Mago is now also available in the wireless version (wireless) therefore for its installation it is not necessary to drill the wall • Allows automatic and fast programming based on the user's schedule and habits • Allows management from different smartphones and tablets , so that every member of the family can interact • Follows your programs by creating five different daily scenarios linked to multiple temperature requirements ("daytime", "nighttime", "evening", "away from home" scenario, etc.) • It saves you money and you can consult energy consumption graphs with weekly, monthly or yearly trends Digital control panel The Duo-tec E range of boilers is equipped with a new digital control panel with backlit LCD display that is even clearer and simpler to use thanks to dedicated and independent keys for regulating the temperature of the domestic hot water and heating. The display allows you to view all the information and set the operating parameters in an intuitive and immediate way Exchanger preheating function The boilers of the Duo-tec E range are equipped with the exchanger pre-heating function which guarantees the immediate production of domestic hot water at the set comfort temperature. In fact, the sanitary water passing through the plates of the preheated exchanger is already supplied at the desired temperature without waiting times . The function can be easily activated/deactivated by a specific boiler parameter Fully modulating pump with de-aeration The circulation pump can operate at maximum speed, minimum speed or in "automatic" mode: in the latter case, the speed (min./max) will be selected so that the delivery/return ∆T in heating remains constant at 20 °C thus ensuring a significant reduction in pump consumption and, given the lower mechanical stresses (compared to a pump that always runs at maximum speed), also in maintenance costs Efficiency and savings Wide modulation range • Greater efficiency given by less switching on and off: with a high modulation ratio, the reduction of continuous switching on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions • Adjustment of the thermal power produced to the dissipated power thus avoiding excessive overheating/cooling of the premises GAC Gas Adaptive Control It is an innovative system which, thanks to a new control electronics and a new electronic gas valve, guarantees automatic control of combustion to constantly maintain maximum efficiency values Advantages • No manual intervention - reduced measuring, calibration or nozzle changing • With this system, the boiler self-adapts to the quality of the gas and the length of the flue gas pipes, keeping efficiency constant • The boiler also constantly regulates itself to maintain the maximum efficiency values, favoring a reduction in gas consumption and generating less pollution thanks to the continuous control of emissions Guidelines in case of replacement of a conventional boiler with a new condensing one There are two main problems that can be encountered: • FLUES AND FUME EXHAUST DUCT • CONDENSATE DRAIN To remedy the above it is recommended: the use of a Ø50 mm exhaust pipe Baxi has in fact developed a system that allows easy ducting in existing flues (for 24kW models). For condensing boilers, the novelty is brought about by the low temperatures of the fumes which allow the use of specific plastic materials; however, in the presence of existing 316 stainless steel flues, installed correctly and with gaskets suitable for receiving damp fumes, there are no problems and they can easily be reconnected to the new boilers while it is absolutely not compliant with the use of aluminum flues or smoke pipes . In fact, aluminum is a metal that is not resistant to the acid condensates present in the fumes Each Ø50 mm diameter bend decreases the length of the drain by 4m the use of the condensate drain pump Baxi has designed this kit to collect the condensate produced by condensing boilers for domestic use: the pump allows the creation of condensate drainage systems in the absence of natural drainage near the boiler. The operation of condensing boilers determines the formation of condensate, due to the principle of condensation. This water therefore needs to be disposed of through special drains. If there is no adequate slope and therefore it is not possible to dispose of the condensate by gravity, it is necessary to install a pump that conveys it towards the drains. The pumps used are also equipped with special non-return valves to avoid bacterial contamination due to any stagnation and return of the waste water. The use of these devices also makes it possible to respect the aesthetics of the buildings by avoiding the use of annoying pipes. Main Features Luna Duo-Tec E • Modern and elegant design for the whole range • Baxi Mago STANDARD: Dedicated app for smartphones and tablets for remote control of the boiler (for Luna Duo-tec E 24/33 Mago models); accessory on request for all the other models • Wide modulation range up to 1:7 (1:6 mod. 1.12) greater efficiency and silence • GAC (gas adaptive control): automatic combustion control • Digital control panel with large backlit LCD display • Arrangement for combination with the Baxi integrated solar system • Connection to rigid and flexible Ø50 mm exhaust pipe: solution for restoring flues - for mod. 24 kW total length 40 meters (intake+exhaust) Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

BERETTA WALL-MOUNTED BOILER Open chamber MYNUTE 24 CAI LX Low Nox 24 kw CNG cod. 20151436 Mynute LOW NOX Nominal heat input kW 25.80 Nominal thermal power (80 - 60 °C) kW 24.05 Reduced thermal power (80 - 60 °C) kW 11.28 Reduced heat input kW 12.5 Electric power Watt 115 Supply voltage / frequency Volt/Hz 230 / 50 Electrical protection degree IP X5D Useful efficiency at Pn max ((80 - 60 °C) % 93.2 Useful efficiency at 30% of Pn (47 °C return) % 91.8 POLLUTANT EMISSIONS (G20) NOx according to UNI EN 483 class 5 HEATING EXERCISE Maximum pressure and temperatures bar/°C 3 / 90 Heating temperature selection range °C 40 / 80 Pump: pump head available for the system mbar 275 at a flow rate of 1000 litres/h Expansion vessel capacity 9 litres HEALTHCARE EXERCISE Maximum pressure 6 bar Minimum pressure bar 0.15 Quantity of hot water with ∆t=25°C litres/min 14 Minimum domestic water flow rate litres/min 2 DHW temperature selection range °C 37 - 60 CONNECTIONS Heating inlet - outlet Ø 3/4” DHW inlet - outlet Ø 1/2” Gas inlet Ø 3/4” COAXIAL FUME EXHAUST AND AIR INTAKE PIPES Diameter mm 60 - 100 Maximum length 2.5 m Loss for inserting a 90° / 45° bend m 1.5 / 1 SEPARATE FUME EXHAUST AND AIR INTAKE PIPES Diameter mm 80 + 80 Maximum length m 14 + 14 Loss for inserting a 90° / 45° bend m 1.7 / 1.2 DIMENSIONS, WEIGHT, GAS Boiler size (HxLxP) mm 780x400x338 Weight kg 35 Wall mounted boiler Beretta MYNUTE 24 CAI LX natural draft open instant combined methane Heating capacity 24kW and DHW (l/min-?t 25°C) 14, with low Nox emissions, specifically designed to facilitate the replacement of pre-existing wall boilers, Simple and intuitive digital display. Technical features: New boilers with low NOx emissions Low consumption circulator (EEI?0.20) as standard Specifically designed to facilitate the replacement of pre-existing wall-mounted boilers 9 liter expansion tank Simple and intuitive digital display Predisposition for climatic thermoregulation (optional external probe)Predisposition for connection to the BeSMART Comfort control (code 20143539) IPX5D electrical protection degree Plumbing fittings, gas and sanitary taps (optional) The ecological burner To reach high standards Mynute Low NOx is equipped with a special atmospheric burner, cooled and equipped with nozzles in number superior, which allows the specification premixing of gas and air. In this how combustion occurs a temperatures lower than usual in a traditional burner. The burner consists of a surface on the which develops the high flame few millimeters, also called "microflame". The tube that passes through the burner with the return water from the system heating promotes cooling of the burner surface. Product Warranty The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Baxi Luna Classic 24 kW low NOx condensing boiler complete with methane or LPG fume exhaust kit - New optional Wi-Fi Technical features Sanitary nominal thermal power kW 24.7 Heating rated thermal power kW 20.6 Useful thermal power at thermal power nom. and high temp. regime* P4 kW 20 XL load profile Seasonal space heating energy efficiency class A Water heating energy efficiency class A Seasonal space heating energy efficiency ?s % 94 Minimum operating temperature °C -5 Heating expansion vessel capacity l 7 Sanitary water production ?T 25°C (1) l/min 13.8 Dimensions (hxwxd) mm 700 x 395 x 285; 28.5 Degree of protection IPX5D CLASSIC MOON The new Luna Classic is the ideal product for apartments or small houses. Its compact dimensions (700x395x285 mm) ne allow installation in confined spaces such as kitchen wall units or in the laundry room. Excellent value for money, simple and intuitive management. The heart of the Luna Classic is the new electronic platform: this revolutionary system replaces the functions of the historical Luna models, raising the quality of the product to a new level. Great attention has been paid to meeting the needs of the end user. System customization and optimization are possible without compromising ease of use. The Luna Classic range includes 2 models for heating and the instantaneous production of domestic hot water, Luna Classic 24 and Luna Classic 28 User Interface Luna Classic Control Panel Renewed interface with: Backlit menu with icons; Simple settings to adjust the heating and domestic hot water temperature via two dedicated knobs; 4 buttons with dedicated functions: menu, confirm, back and reset. 2 functions for perfect water temperature Domestic hot water management can be enhanced and improved by activating two dedicated functions: relaxation function It is a pre-heating function which keeps the domestic hot water at the desired temperature for a pre-set period of time, or for 30 minutes after selecting the chosen temperature. Boost function Activates the boiler at maximum power for faster delivery of hot water. Baxi MaGO Luna Classic can be connected directly to the Baxi Mago, the modulating chronothermostat with integrated wi-fi that allows you to manage home comfort directly from an App. By downloading the dedicated App onto your smartphone, it will be possible to connect to one or more homes to control the temperature, manage the programming, display the consumption graph, read any messages error, set vacation mode, etc. The combination of the boiler with the Baxi Mago A+ kit increases its energy efficiency, raising it to class A+ Specifications: Operation with a mixture composed of up to 20% hydrogen New single coil stainless steel heat exchanger, featuring sections with large water passages for greater seasonal thermal efficiency Seasonal energy efficiency of 94% thanks to the advanced technology applied Renewed interface with backlit display Easy replacement of conventional boilers thanks to central flue gas outlet Modulation range 1:5 greater efficiency and silence Ø80 double exhaust STANDARD Connection to Ø50 mm rigid and flexible waste pipe: solutions for the rehabilitation of flues total length (exhaust + intake) 40 meters Connection to pressurized collective flues Boilers running on methane that can be converted to LPG and propane by means of a specific regulation (conversion kit not necessary) Compact dimensions: 700x395x285 mm Class A+ for Luna Classic 24/28 models with Baxi Mago and external probe (as accessories) New hydraulic group that guarantees maximum levels of performance and durability over time Optimal insulation for silent operation Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

VAILLANT ecoTEC PRO CONDENSING VMW 286/5-3+ COMPLETE WITH FUME EXHAUST KIT -ErP NOx 5 Technical features For heating and domestic hot water production Forced draft sealed chamber Nominal thermal power 24.0 kW ErP energy class (Heating and DHW): Class A DHW nominal heat input 28.6 kW Nominal heat input in heating mode 24.5 kW Water content in the generator 2.2 l Expansion vessel capacity 10 l Domestic hot water production (ΔT = 30K) 13.4 lt Dimensions (hxpxl) mm 720 x 338 x 440 ; 36kg Version: CNG General characteristics Vaillant condensing boiler EcoTEC PRO The wall mounted boiler that offers the right balance between performance and comfort. The ecoTEC pro VMW (heating and DHW production) are available in power ratings of 19 and 24 kW. ecoTEC pro was born as the natural evolution of Vaillant's consolidated technology and experience in condensing technology. ecoTEC pro has been designed to offer the right balance between performance and comfort both in heating and in the production of domestic hot water. Its simplicity of regulation makes it the ideal boiler for all users. ecoTEC pro is equipped with an extremely simple interface with plain text and backlit display. The small dimensions of ecoTEC pro VMW 70cm high, 44cm wide and 35cm deep (identical to the previous version) allow installation in any environment. A new high-efficiency pump and new electronics allow ecoTEC pro to consume very little electricity, guaranteeing considerable savings throughout the year. Instant DHW production Intuitive user interface Simplicity of management ****Efficiency in heating Modulation 1:5 Modulating pump (Class A) Steel primary exchanger 10 l expansion vessel transfer kit from methane to propane or propane air code 0020160884 Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

CHAFFOTEAUX CX GREEN 24 EU CONDENSING GAS BOILER COMPLETE WITH LPG FUME KIT Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL LPG supply Characteristics of heating/DHW operation: Nominal heat input in heating max/min (Hi): 23.5/4.5 kW Max/min DHW nominal heat input (Hi): 23.5/4.5 kW Max/min heating thermal power (80°C-60°C): 23/4.4 kW Efficiency at nominal heat input: 97.7 / 88% Efficiency at 30% of the nominal heat input: 104.3 / 94% Expansion vessel capacity: 8 l Min/max heating temperature (high temperature range) °C 35/82 Min/max heating temperature (low temperature range) °C 25/45 DHW temperature min/max °C 36/60 Instantaneous quantity of hot water ΔT=25°C l/m 13.9 Instantaneous quantity of hot water ΔT=35°C l/m 9.9 Minimum withdrawal of hot water l/m <2 Electrical data: Supply voltage/frequency V/Hz 230/50 Total absorbed electric power W 34 Electrical protection degree IP X5D CX GREEN EU   The compact condensing boiler with aluminum alloy condensing exchanger and with all the necessary requirements to achieve the required standards in terms of energy saving. Operation only methane. Sanitary comfort Sanitary heat exchanger in stainless steel. Domestic water performance: stars **. Flow rate 13.1 litres/minute with ΔT = 25ºC. (24kW) Heating comfort Efficiency up to 108% with energy savings up to 35%. 4-star combustion efficiency in compliance with the EN92/42 standard. Modulation range from 25% to 100% of maximum power. Condensing exchanger in aluminum alloy. Reduced polluting emissions, NOx class 5. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Arrangement for integration into a heating system via the Ebus2 communication protocol (boilers, solar, system management modules and modulating thermoregulation accessories). Possibility of managing single-temperature and multi-temperature zones only via Expert Control. Self-diagnosis system by code. LCD display. Comfort of use and installation Possibility of connection with external probe. Compatible with Expert Control, modulating accessories and on/ff. Easier starting: automatic purge function and directly accessible combustion regulation. Energy saving and respect for the environment Up to 20% energy savings in combination with chronothermostat and external probe. 40% reduction in CO 2 emissions **. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE PRODUCT IS MADE TO ORDER. IT WILL BE SHIPPED WITHIN 10 BUSINESS DAYS FROM THE DATE OF PURCHASE. ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Technical features ErP energy efficiency class (heating and DHW): A Load profile: XL DHW nominal heat input kW 24.7 Heating nominal heat input kW 20.6 Sanitary nominal thermal power kW 24 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.6% Efficiency at 100% Pn (50-30°C): 105.4% Expansion/pre-charge vessel capacity l/bar 7.5/0.8 Sanitary water temperature adjustment °C 35-60 Boiler capacity 40 l Boiler expansion vessel capacity/pre-charge l/bar 2/3.5 Sanitary water production ∆T 25°C l/min 13.8 Sanitary water production at discharge ∆T 30°C l/30' 385 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions (hxlxp): 950x600x466 mm ; 65.5 kgs Power supply: CNG or LPG Cloud Platinum+ Wall mounted gas condensing boilers for heating and DHW production with storage Total modulation pump The Luna Platinum+ range is renewed with the introduction of a high efficiency electronic pump with permanent magnet motor. The new fully modulated pump allows, compared to using a pump Traditional modulating: Lower electricity consumption Better performance Greater durability Plant deaeration New electronic "system deaeration" function to facilitate the removal of air during initial ignition. Efficiency and savings The objective of a heat generator is to supply the energy necessary to the rooms to maintain conditions of maximum comfort inside them: this means supplying the rooms, through the system, with the same amount of heat that the building loses . In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. Wide modulation range Reduction of on-off cycles The graph shown above highlights the reduction in on/off cycles which distinguishes the new Platinum+ boilers with modulation up to 1:10 compared to a condensing boiler with lower modulation. The reduction of the on/offs determines an improvement in the efficiency of the boiler and consequently a considerable saving for the end user. Standard condensing boilers, on the other hand, with a limited modulation range work at a minimum power level above 6 kW; this allows it to avoid the on/off cycles for only 3% of the period of operation in heating, compromising the performance of the boiler and the life of the components. GAC: Gas Adaptive Control The electronics and the gas valve with stepper motor that the new Platinum+ boilers are equipped with guarantee automatic combustion control which is based on: on the flame signal GAC via the flame signal The system continuously measures the flame signal during boiler operation and adjusts the gas flow rate in order to keep the combustion quality constant and all this without requiring any additional component inside the combustion chamber. Installers and end users enjoy the following benefits of the GAC: The automatic combustion control favors a reduction in installation times as no manual adjustment of the gas valve or nozzle change is required: in fact, it is sufficient to manually modify some parameters of the electronic board for operation with LPG The boiler self-adapts to the quality of the gas and the length of the flue gas outlets: this means that there are no manual adjustments to make High modulation field 1:10: high efficiency and savings, since such a wide modulation field determines a greater adaptability of the boiler to the thermal dispersions of the building to obtain a higher efficiency and greater durability of the components. The reduction of the on/off cycles, in addition to the greater efficiency, guarantees less noise produced by the boiler Unlike traditional condensing boilers, the boiler always works adjusted to maximum efficiency values ​​favoring a reduction in gas consumption and consequently a lower environmental impact thanks to the control of CO/CO emissions Power sets The term Power set identifies the heating power regulation process according to the project data. The thermal capacity of the boiler, through the Power set device, is adjusted according to the energy requirement: just act on the control panel to adjust some parameters Full soundproofing C structure Silence is the relative or absolute absence of sound or noise. The noise level of the Luna Platinum+ boiler is comparable to a normal conversation Digital pressure gauge The electronic pressure transducer in the hydraulic unit allows you to check the pressure directly on the display. Double alarm level in the event of low pressure: a "warning" level in the event of low pressure in the boiler; a "block" level in the event of a lack of pressure Intubation solution For the rehabilitation of flues Baxi has developed a system that allows easy ducting into existing flues thanks to a Ø50 mm exhaust pipe (for 24kW models). Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. FOR CONVERTING TO LPG, CONTACT THE AUTHORIZED ASSISTANCE SERVICE IN ADVANCE JUNKERS BOSCH CERAPUR BUILT-IN CONDENSING BOILER ZWB 24-1 EI 24 kW INCLUDING FUME KIT - NEW ErP ErP energy class (Heating and DHW) For heating and domestic hot water production Nominal heat input in DHW kW 24.49 Nominal heat output (heating) 40/30 °C: 25.7 kW Nominal heat output (heating) 80/60 °C: 24.0 kW Minimum heat input (sanitary): 7.4 kW Sanitary flow rate ΔT = 30 K: 11.5 l/min NOx class: 5 Voltage v(AC): 230 HZ frequency: 50 Absorbed electric power: 140 W IP Protection Degree: X5D Dimensions: 243 x 533 x 775; 47 kgs Standard: Controllable from home - Management of the boiler directly from inside the home, using the TF 25 remote control , supplied as standard Junkers Bosch With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. CerapurRecessed CERAPUR INCASSO is designed for concealed installations and encloses maximum comfort in just 250 mm of depth. Ideal for solving space problems, it does not alter the aesthetic beauty of homes. In fact, CERAPUR INCASSO integrates perfectly into the façade thanks also to the possibility of painting the "shell" with the same color as the wall. Boiler for concealed installations - Space saving inside the home and no aesthetic impact on the outside thanks to the installation in the niche in the wall Controllable from inside the house - Management of the boiler directly from inside the house, using the TF 25 remote control, supplied as standard Robust and reliable - Robustness and reliability of the boiler are guaranteed thanks to the aluminum alloy construction of the primary exchanger Electrical insulation - The boiler has an IPX5D degree of electrical insulation Characteristics: Wall-mounted condensing boilers for outdoor use with DHW production that can be combined with solar thermal systems for DHW using the Solar Kit. C13, C33, C63, C83, B33 type certifications obtained. Suitable for use with Ø 60 mm drains. Class 5 emissions required by UNI EN 297, UNI EN 483 and UNI EN 15502 standards. External installation indicated in a special niche, dedicated to the built-in Guscio (acc. 978). Automatic antifreeze function up to an external temperature of -15 °C, both on the DHW and heating sides. Fully automatic filling function for the heating circuit. Continuous power modulation (DHW and heating). Patented high efficiency silicon-aluminum alloy primary heat exchanger. Oversized sanitary plate heat exchanger for condensing also in DHW. Heating side expansion vessel of 6 litres. Circulator in Energy Class A. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less