General characteristics Energy label specifications according to the European ErP directive   Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 28/3.0 Max/min heating thermal power (80°C-60°C) kW 27.1/2.9 Efficiency at nominal heat input (60/80°C) % 97.7 Efficiency at nominal heat input (30/50°C) % 106.2 Efficiency at 30% at 30°C % 108.8 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Specific flow rate in DHW (10 min. with ∆T=30°C) litres/min 14.1 Quantity of hot water ∆T=25°C litres/min 16.8 Quantity of hot water ∆T=35°C litres/min 12 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 81 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 770/400/385 CNG or LPG power supply Kit for conversion from methane to propane supplied Ariston condensing boilers   1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water.   Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies...  Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers.  EVO: energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the Energy Certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston satisfies all the indications envisaged for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energy.   Genus Premium Evo The Genus Premium Evo wall-mounted boiler is the maximum expression of the Ariston range. Thanks to the condensing technology, by recovering the energy of the exhaust fumes, it generates an increase in the calorific value which makes it possible to eliminate waste (of energy) and to obtain higher thermal efficiency than conventional boilers. Genus Premium Evo offers even greater performance thanks to the innovative technology that allows it to self-regulate according to variations in the external and internal temperature of the room, allowing energy savings of up to 35% compared to an older generation boiler. It is available in the heating and domestic hot water production version in 3 powers: 24-30-35 kW (sealed chamber).   Characteristics: Can be installed in partially protected places Large backlit dot matrix screen Continuous modulation high-efficiency circulator: for optimizing consumption and maximizing performance. Modulation ratio 1:10 - Automatic power regulation according to the heating request. Acoustic comfort guaranteed by the lower number of boiler on and off cycles, new silencer and sound-absorbing panels Prepared for integration in system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort Isothermal primary heat exchanger in stainless steel Increased sanitary exchanger Cold water inlet and heating return filters  Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons  Acoustic comfort Acoustic comfort is further guaranteed by the introduction of the new silencer. For the Clas Premium Evo thanks also to the high modulation ratio of 1:10, the continuously modulating pump and the presence of side sound-absorbing panels.  High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology   Ecodesign directive: from 2015 only new condensing boilers    After very long negotiations , the Ecodesign regulation was approved which introduces a new energy labeling on the minimum efficiency standards for boilers. In particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for domestic hot water production appliances. Hence the obligation to install only condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimney as occurs in traditional boilers. The recovered heat is transferred to the heating system, allowing to reach an efficiency of 106% against 92% of the traditional boiler and 84/85% of an old traditional generator. The installation obligation concerns boiler manufacturers who will no longer be able to place non-condensing ones on the market starting from 26 September 2015 . This means that starting from this date, anyone wishing to install a boiler in their own home will only have to install condensing models. Only a particular type of non-condensing boiler will continue to be produced which is technically called "open chamber" to be installed when it is not possible to replace an old boiler with a condensing boiler due to problems related to the collective flue of some multi-family buildings . What is Energy Labeling?       Products for heating water and the environment represent around 30% of internal energy consumption in Europe. Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations such as Italy were deactivated. As of 26 September 2015, ErP regulation and energy labeling will be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and water storage tanks hot)¹.   How to read energy labels    There are different labels, based on the type and functions of the product (water heating or space heating only or both, and in this case the label must show both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Vaillant ecoTEC Exclusive VM 296/7-5+ Condensing Boiler Natural Gas Heating Only with ErP Ready Fume Exhaust Kit Technical features CNG item code: 0010017088 Heating Efficiency Class: A Nominal Thermal Power (80/60°C): 29.7 kW Nominal Thermal Power (60/40°C): 30.6 kW Nominal Thermal Power (50/30°C): 32.0 kW Nominal Thermal Power (40/30°C): 32.1 kW Nominal Thermal Power in Sanitary: 28 kW Nominal heat capacity in sanitary water: 28.6 kW Nominal heat input in heating: 30.3 kW Nominal efficiency (80/60°C) : 98% Efficiency at 30% : 108.5% Performance Stars : **** Inlet Gas Pressure: 37 mbar Consumption at Nominal Power : 3 m 3 /h Class : NOx 5 Nominal flow rate in Heating (ΔT=20K) : 1075 l/h Inbound Adjustment Temperature: 35-75 °C Water Content in the Generator : 2,2 l Power supply (V/Hz): 230/50 Total Electric Power: 81 W Stand-By Electric Power: <2 Gas connection: 20 mm Smoke Exhaust Fitting: 60/100 mm Sound Power : 50 dB(A) Degrees of Protection : IP X4 D Dimensions and weight Boiler dimensions (HxPxL): 720x338x440 Boiler weight: 35 Kg ecoTEC Exclusive VM+ All the comfort you are looking for with maximum efficiency and reliability The ecoTEC exclusive WM + wall-mounted condensing boiler has been designed to guarantee minimum harmful emissions into the environment, guaranteeing maximum performance for domestic comfort . This model of indoor boiler allows a lower consumption of gas and electricity thanks to the high quality components mounted inside such as the high efficiency pump which allows a wide modulation range. Furthermore, the ecoTEC exclusive adjusts itself automatically to provide the best comfort by making the most of the principle of condensation. The boiler internally mounts a gateway which, in combination with the multiMATIC 700 control unit (accessory that can be ordered separately, not included in the supply, mandatory for connectivity), can be interfaced with the home router with a LAN cable or a Wi-Fi transmission dongle ( can be ordered separately); through a free app developed by Vaillant it will be possible to regulate the boiler comfortably from a smartphone . This boiler model is for the production of heating only , but if combined with a Vaillant boiler it can also supply domestic hot water. ecoTEC Exlusive is the Green iQ branded condensing boiler. The boiler reaches 94% (Etas) of energy efficiency in heating thanks to the performance of the ExtraCondens exchanger which has an additional section capable of increasing DHW production efficiency by 10%. The boiler is fitted with the VR920 device which, combined with the multiMATIC 700, allows you to connect the boiler to the home WiFi network and, using an App (iOS and Android), to control it even from outside the home. It self-adapts to any type of gas and consists of 82% recyclable material effect of the made in Germany conception. The boiler has already received the Reddot Design Award. Advantages Comfort Very low noise Hot water production up to 17 l/min Unparalleled sanitary and environmental comfort savings Energy class A+ with multiMATIC 700 Excellent energy/efficiency ratio Gas self-adaptation/regulation Up to 10% annual savings compared to normal condensation Safety Environmentally friendly: 82% recyclable boiler and components Strict controls to ensure the high quality standards of Green iQ Simplicity Built-in connectivity Free app for remote management from smartphone, tablet or PC Easy and intuitive programming Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

IN THE ABSENCE OF THE PRODUCT THE NEW CARES S 30 MODEL WILL BE SHIPPED CARES PREMIUM 30 EU ErP METHANE condensing BOILER COMPLETE WITH FUME EXHAUST KIT Product code: 3300760 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Nominal heat input in heating: Kw 28 Nominal heat input in sanitary max: Kw 28 Useful thermal power in heating: max: Kw 28.4 Efficiency at nominal heat input (60/80°C): 97.8% Efficiency at nominal heat input (30/50°C): 104% Efficiency at 30% at 30°C: 108% Max/min heating temperature (high temperatures): 82/35°C Max/min heating temperature (low temp.): 45/25°C Max/min DHW temperature: 60/36 °C Sanitary water production (DT=25°C): lt./min. 16.3 Specific flow rate (first 10' with DT=30°C): lt./min. 11.6 Total absorbed electric power W 82 Degrees of protection of the electrical system IP X5D Dimensions (HxWxD) mm 745 x 400 x 319 Power supply: METHANE ARISTON CARES PREMIUM 30 EU CONDENSING BOILER - NEW ErP Technical features Product code: 3300760 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Nominal heat input in heating: Kw 28 Nominal heat input in sanitary max: Kw 28 Useful thermal power in heating: max: Kw 28.4 Efficiency at nominal heat input (60/80°C): 97.8% Efficiency at nominal heat input (30/50°C): 104% Efficiency at 30% at 30°C: 108% Max/min heating temperature (high temperatures): 82/35°C Max/min heating temperature (low temp.): 45/25°C Max/min DHW temperature: 60/36 °C Sanitary water production (DT=25°C): lt./min. 16.3 Specific flow rate (first 10' with DT=30°C): lt./min. 11.6 Total absorbed electric power W 82 Degrees of protection of the electrical system IP X5D Dimensions (HxWxD) mm 745 x 400 x 319 Power supply: METHANE CARES PREMIUM EU The CARES Premium wall-mounted boiler combines condensing technology with practical installation and compact dimensions. Cares Premium is available in the heating and domestic hot water production versions with powers of 24 and 30 kW Characteristics: LCD displays Continuous modulation high efficiency circulator Modulation ratio 1:4 Arrangement for integration with system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation (with Sensys) Arrangement for solar system management Aluminum alloy primary exchanger Sanitary plate heat exchanger Self-diagnosis system by code Cold water inlet and heating return filters Anti-freeze, anti-limescale and anti-blocking circulator protection Operation only with METHANE gas Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

CAUTION Methane, LPG and propane air operation without the need for a kit. The transformation takes place thanks to the combustion control by selecting the type of gas from the technical menu. For info, contact the local authorized assistance center in advance ARISTON condensing BOILER ALTEAS ONE NET 30 KW EU LPG COMPLETE WITH FUME EXHAUST KIT - ErP Technical features Product code: 3301059 Energy label specifications according to the European ErP directive Class A heating energy efficiency (A+ achieved thanks to thermoregulation) Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal thermal power kW 28 Annual energy consumption in heating 48 gj Annual electricity consumption 49 kWh Seasonal space heating energy efficiency % 94 Water heating energy efficiency % 85 Sound power level inside 51 dB DHW flow rate ∆T 25 °C (l/min) 17.2 Dimensions 24 kW mm (HxWxD) 745 x 400 x 315 Indoor installation and partially protected places Power supply: methane or LPG Functionality: Connectivity integrated in the boiler HI-Comfort functions AUTO, Comfort, CARE Thermoregulation including CUBE thermostat + external probe Large display, touch interface XtraTech stainless steel heat exchanger New XTRATECH heat exchanger : Maximum quality. XtraTech is the new Ariston exclusive stainless steel heat exchanger, the heart of the ONE condensing boilers, developed to guarantee reliability and performance over time. Increased passage sections: +142% compared to the previous exchanger. Higher prevalence, lower risk of clogging, better performance. Every day, as if it were the first. Every single component has been designed to guarantee performance and durability over time: Ariston guarantee, shown in each component. Every single component has been rigorously tested and controlled on the production line. 100% of the boilers are tested again before being shipped to our customers. The best materials have been selected, to work for a long time even in the most critical situations. Excellent results, over time. Always connected with Ariston NET Wherever you are, always within reach of your Smartphone. Managing the comfort of your home has never been easier! Wherever you are, you can control the climate in your home using your smartphone. Use only the energy it needs. Easy to manage weekly time programming, directly from the app. Also, choose the savings "leaflet" for a real reduction in bill costs! Technical support always ON. Thanks to the innovative remote control system, the app warns your customer in case of malfunctions. By signing a maintenance contract, the Assistance Center will be able to intervene in the event of breakdowns, even remotely. Customer serenity is at the heart of Ariston NET. Absolute efficiency: Thermoregulation in class A+ The ONE condensing boilers achieve very high seasonal performance and thanks to the thermoregulation they reach class A+! Alteas and Genus ONE are also equipped with the innovative IGNITION system, which makes combustion always perfect thanks to the electronic control. Gas transformation? No problem, from the technical menu in one touch. Total Comfort : Innovative functions to satisfy your need ONE is equipped with an innovative set of smart functions to guarantee comfort every day with minimum waste of energy. Auto function: Patented function that allows you to automatically optimize the operation of the boiler, eliminating continuous switching on and off, reducing the stress on the components to a minimum. Comfort function: Hot water without any waiting! Lots of water with minimum energy consumption. Integrated Programming: Weekly hourly programming integrated into Alteas and Genus ONE products. Care function: Automatic reminder of routine maintenance. ALTEAS ONE NET Top of the range condensing boiler, Italian design and integrated connectivity. It represents the perfect combination of excellent performance and innovative design. The front panel in tempered glass, the HI-tech display and integrated connectivity make Alteas the perfect boiler for exclusive furnishing solutions. The efficiency of the boiler combines with the advantages of the Ariston NET service to control your system remotely, keep consumption under control and have peace of mind thanks to a technician who is always by your side. All via a simple free smartphone app! New XtraTech heat exchanger in exclusive Ariston stainless steel, with high head Exchanger passage sections +142% compared to the previous version Tempered and scratch resistant glass panel Large display, touch interface Ignition system, electronic combustion control Gas transformation from the technical menu Class A+ in heating, thanks to the Cube thermostat and external probe included as standard Modulation ratio 1:10 Ariston NET connectivity included in the boiler BusBridgeNet® communication protocol AUTO function, Comfort New CARE function, automatic reminder of routine maintenance Internal sound absorbing panels Installation in partially protected places Fumes discharge 80, 60, 50 m Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

RIELLO FAMILY EXTERNA CONDENS 3.0 KIS METHANE CONDENSING BOILER COMPLETE WITH FUME KIT - NEW ErP Technical features Product code: 20102940 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Furnace thermal power (heating) min-max: 3.2÷25 kW Useful thermal power (sanitary) min-max: 3.2÷30 kW Energy efficiency (92/42/EEC) **** Useful efficiency at Pn* (50°C-30°C): 106.8% Profit return 30% (47th return): 107.9% Sealed chamber, forced draught Quantity of hot water with Δt 25°C: 17.2 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 1002 x 475 x 311 ; 50 Kgs Electrical protection degree: IP X5D NOx class: 5 Power supply: METHANE Family Remote Control, supplied as standard FAMILY EXTERNAL CONDENS Yield **** Low polluting emissions Aluminum condenser, with premix burner Models for combined instantaneous and storage heating For outdoor installations in the open Family Externa Condens is an outdoor wall-mounted boiler that can be installed totally in the open. The new primary heat exchanger completely made of aluminum with front access to the combustion chamber ensures better efficiency and durability. It is available with powers from 3.2 to 30 kW. Characteristics: Modulation ratio 1:10 (minimum power 3.2 kW) which allows the boiler to respond to all heat requests Modulating circulator, low consumption (IEE≤0.20) 3 Stars in sanitary comfort according to EN 13203 Family Remote Control, supplied as standard, allows management of all boiler functions directly from inside the home Antifreeze up to -15°C Remote alarm system that allows remote signaling of the boiler lockout status Special Family functions: Wellness key, Memory key, Touch&Go function, Intelligent system filling Standard external probe. The FAMILY Remote Control kit (remote control panel) is the tool that allows you to manage the boiler remotely. The panel monitors the boiler, storage tank and room temperatures, monitors and supervises the operating regimes, the activation times and signals any anomalies. The remote control panel can be configured as: Chronothermostat (factory confi guration): it will work according to the standard heating program or according to the personalized one. In this configuration the control panel tries to keep the room at two temperature levels (comfort and reduced), passing from one to the other at times established by the user. Thermostat: heating is activated when the temperature detected by the room probe (contained in the control panel) is lower than the one set, regardless of the memorized heating program. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

OFFER VALID UNTIL STOCKS LAST! For LPG operation, carry out the adjustment through the local assistance centre Technical features Model : Thema Condens 30 IS HIT Product code : 0010034553 Power supply: methane/LPG Energy efficiency Heating energy efficiency class: A Sanitary energy efficiency class: A ACS profile : XL Heating Capacity at the hearth 80°/60°C : 6.4 ~ 25.6 kW Sanitary Capacity at the hearth 60°C : 6.4 ~ 31.0 kW Continuous flow rate (∆T = 25K) : 18 l/min Dimensions Dimensions (LxHxP): 418x740x344 mm Product Guarantee : All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS BORN WITH METHANE. THEREFORE, THE STANDARD TRANSFORMATION KIT WILL BE SUPPLIED. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE ARISTON CONDENSING BOILER CLAS ONE L 30 kW LPG COMPLETE WITH FUME EXHAUST KIT Wi-Fi OPTIONAL Technical features Product code: 3301024 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal heat input max/min heating kW 28 / 4.3 Nominal DHW max/min heat input kW 30 / 4.3 Useful heat output max/min heating kW 27.4 / 3.9 Efficiency at nominal heat input (60/80°C) 97.9% Efficiency at nominal heat input (30/50°C) 107.3% Efficiency at 30% (30°C) 109.6% Heating max/min temperature (high temperature) °C 83/35 Heating max/min temperature (low temperature) °C 46/20 Max/min domestic hot water temperature °C 61 / 36 quantity of hot water (deltaT 25°C) 16.4 l/min Quantity of hot water (deltaT 35°C) 11.7 l/min Specific flow rate (first 10' with deltaT 30°C) 14.5 l/min Minimum operating temperature (-5°C with antifreeze kit)** °C > 0° Total absorbed electrical power 78 W Degree of protection of the electrical system IP X5D Dimensions 24 kW mm (HxWxD) 745 x 400 x 315 Power supply: LPG Functionality: Wi-Fi optional XtraTech™ stainless steel primary exchanger AUTO, Comfort functions Indoor installation and partially protected places ONE Series, the new generation of condensing boilers New XTRATECH™ exchanger: Maximum quality. XtraTech™ is the new exclusive* Ariston stainless steel heat exchanger, the heart of the ONE condensing boilers, developed to guarantee reliability and performance over time. Increased passage sections: +142% compared to the previous exchanger. Higher prevalence, lower risk of clogging, better performance. Every day, as if it were the first. Every single component has been designed to guarantee performance and durability over time: Ariston guarantee, shown in each component. Every single component has been rigorously tested and controlled on the production line. 100% of the boilers are tested again before being shipped to our customers. The best materials have been selected, to work for a long time even in the most critical situations. Excellent results, over time Always connected with Ariston NET Wherever you are, always within reach of your Smartphone. Managing the comfort of your home has never been easier! Wherever you are, you can control the climate in your home using your smartphone. Use only the energy it needs. Easy to manage weekly time programming, directly from the app. Also, choose the savings "leaflet" for a real reduction in bill costs! Technical support always ON. Thanks to the innovative remote control system, the app warns your customer in case of malfunctions. By signing a maintenance contract, the Assistance Center will be able to intervene in the event of breakdowns, even remotely. Customer serenity is at the heart of Ariston NET. Absolute efficiency: Thermoregulation in class A+ The ONE condensing boilers achieve very high seasonal performance and thanks to the thermoregulation they reach class A+ ! Alteas and Genus ONE are also equipped with the innovative IGNITION system, which makes combustion always perfect thanks to the electronic control. Gas transformation? No problem, from the technical menu in one touch. Total Comfort: Innovative functions to meet your needs ONE is equipped with an innovative set of smart functions to guarantee comfort every day with minimum waste of energy. Auto function: Patented function that allows you to automatically optimize the operation of the boiler, eliminating continuous switching on and off, reducing the stress on the components to a minimum. Comfort function: Hot water without any waiting! Lots of water with minimum energy consumption. Integrated Programming: Weekly hourly programming integrated into Alteas and Genus ONE products. Care function: Automatic reminder of routine maintenance. NEW CLASS ONE L Clas ONE 30 L is the ideal condensing boiler for replacement, especially on large old systems. Advantages compared to the Clas ONE 30: 10-litre oversized expansion tank, 7-metre oversized high-efficiency circulator, 20-plate DHW exchanger, bypass with rigid spring. New XtraTech™ exchanger in exclusive* Ariston stainless steel, with high head Exchanger passage sections +142% compared to the previous version LCD display Class A+ in heating reachable with thermoregulation Modulation ratio 1:7 Prepared for Ariston NET connectivity BusBridgeNet® communication protocol AUTO function, Comfort Optimized internal silencer Sanitary heat exchanger increased 20 plates Expansion vessel increased real 10 l By-pass with rigid spring High efficiency circulator increased 7 m Installation in partially protected places Smoke outlet 80, 60, 50 mm Ecodesign directive: from 2015 only new condensing boilers After very long negotiations , the Ecodesign regulation was approved which introduces a new energy labeling on the minimum efficiency standards for boilers. In particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for domestic hot water production appliances. Hence the obligation to install only condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimney as occurs in traditional boilers. The recovered heat is transferred to the heating system, allowing to reach an efficiency of 106% against 92% of the traditional boiler and 84/85% of an old traditional generator. The installation obligation concerns boiler manufacturers who will no longer be able to place non-condensing ones on the market starting from 26 September 2015 . This means that starting from this date, anyone wishing to install a boiler in their own home will only have to install condensing models. Only a particular type of non-condensing boiler will continue to be produced which is technically called "open chamber" to be installed when it is not possible to replace an old boiler with a condensing boiler due to problems related to the collective flue of some multi-family buildings . What is Energy Labeling? Products for heating water and the environment represent around 30% of internal energy consumption in Europe. Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations such as Italy were deactivated. As of 26 September 2015, ErP regulation and energy labeling will be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and water storage tanks hot. How to read energy labels There are different labels, based on the type and functions of the product (water heating or space heating only or both, and in this case the label must show both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

CAUTION Natural gas, LPG and propane air operation without the need for a kit. The transformation takes place thanks to the combustion control by selecting the type of gas from the technical menu. For info, contact the local authorized assistance center in advance ARISTON condensing BOILER ALTEAS ONE NET 30 KW EU METHANE COMPLETE WITH FUME EXHAUST KIT - ErP Technical features Product code: 3301059 Energy label specifications according to the European ErP directive Class A heating energy efficiency (A+ achieved thanks to thermoregulation) Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal thermal power kW 28 Annual energy consumption in heating 48 gj Annual electricity consumption 49 kWh Seasonal space heating energy efficiency % 94 Water heating energy efficiency % 85 Sound power level inside 51 dB DHW flow rate ∆T 25 °C (l/min) 17.2 Dimensions 24 kW mm (HxWxD) 745 x 400 x 315 Indoor installation and partially protected places Power supply: methane or LPG Functionality: Connectivity integrated in the boiler HI-Comfort functions AUTO, Comfort, CARE Thermoregulation including CUBE thermostat + external probe Large display, touch interface XtraTech stainless steel heat exchanger New XTRATECH heat exchanger : Maximum quality. XtraTech is the new Ariston exclusive stainless steel heat exchanger, the heart of the ONE condensing boilers, developed to ensure reliability and performance over time. Increased passage sections: +142% compared to the previous exchanger. Higher prevalence, lower risk of clogging, better performance. Every day, as if it were the first. Every single component has been designed to guarantee performance and durability over time: Ariston guarantee, shown in each component. Every single component has been rigorously tested and controlled on the production line. 100% of the boilers are tested again before being shipped to our customers. The best materials have been selected, to work for a long time even in the most critical situations. Excellent results, over time. Always connected with Ariston NET Wherever you are, always within reach of your Smartphone. Managing the comfort of your home has never been easier! Wherever you are, you can control the climate in your home using your smartphone. Use only the energy it needs. Easy to manage weekly time programming, directly from the app. Also, choose the savings "leaflet" for a real reduction in bill costs! Technical support always ON. Thanks to the innovative remote control system, the app warns your customer in case of malfunctions. By signing a maintenance contract, the Assistance Center will be able to intervene in the event of breakdowns, even remotely. Customer serenity is at the heart of Ariston NET. Absolute efficiency: Thermoregulation in class A+ The ONE condensing boilers achieve very high seasonal performance and thanks to the thermoregulation they reach class A+! Alteas and Genus ONE are also equipped with the innovative IGNITION system, which makes combustion always perfect thanks to the electronic control. Gas transformation? No problem, from the technical menu in one touch. Total Comfort : Innovative functions to satisfy your need ONE is equipped with an innovative set of smart functions to guarantee comfort every day with minimum waste of energy. Auto function: Patented function that allows you to automatically optimize the operation of the boiler, eliminating continuous switching on and off, reducing the stress on the components to a minimum. Comfort function: Hot water without any waiting! Lots of water with minimum energy consumption. Integrated Programming: Weekly hourly programming integrated into Alteas and Genus ONE products. Care function: Automatic reminder of routine maintenance. ALTEAS ONE NET Top of the range condensing boiler, Italian design and integrated connectivity. It represents the perfect combination of excellent performance and innovative design. The front panel in tempered glass, the HI-tech display and integrated connectivity make Alteas the perfect boiler for exclusive furnishing solutions. The efficiency of the boiler combines with the advantages of the Ariston NET service to control your system remotely, keep consumption under control and have peace of mind thanks to a technician who is always by your side. All via a simple free smartphone app! New XtraTech heat exchanger in exclusive Ariston stainless steel, with high head Exchanger passage sections +142% compared to the previous version Tempered and scratch resistant glass panel Large display, touch interface Ignition system, electronic combustion control Gas transformation from the technical menu Class A+ in heating, thanks to the Cube thermostat and external probe included as standard Modulation ratio 1:10 Ariston NET connectivity included in the boiler BusBridgeNet® communication protocol AUTO function, Comfort New CARE function, automatic reminder of routine maintenance Internal sound absorbing panels Installation in partially protected places Fumes discharge 80, 60, 50 m Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! The boiler will be supplied with methane, for the conversion to LPG and propane air, contact the area Thermotechnical Assistance. Technical features Model : Cerapur Modul Solar ZBS 30/210-3 SOE Product code : 7738100533 Installation : Indoor / outdoor Positioning : Standing / on the ground Power supply: methane Energy efficiency Heating energy efficiency class: A Water heating energy efficiency class: A Declared load profile : XL Seasonal space heating energy efficiency : 92% Performance Nominal heat input : 6.5 ~ 30 .0 kW Nominal heat output 40°/30° : 7.1 ~ 30.6 kW Rated heat output: 6.4~29.4kW Specific flow rate (∆T = 30 K) : 26.2 l/min Boiler capacity: 204 litres Useful efficiency 40°/30° : 103 ~ 109 % Useful efficiency 80°/60° : 98,5 % Heating expansion vessel capacity: 12 litres DHW expansion vessel capacity: 8 litres Solar expansion vessel capacity: 16 litres Fan residual head : 80 Pa NOx class : 6 Electrical protection degree : X4D Dimensions and weight Dimensions (LxWxH): 600x600x1860 mm Weight : 171Kg Floor-standing condensing boiler with integrated Cerapur Modul Solar stratified solar tank Compact solar system The solar system is really very compact, in fact, in about 0.4 m², there are all the components necessary for the construction of a solar thermal system for the production of domestic hot water (DHW). Collectors are excluded. Maximum sanitary comfort The boiler has been awarded, by the European Standard EN13203-1/2, the "3-star sanitary comfort", i.e. the maximum score obtainable by appliances for the production of domestic hot water. Robust and reliable boiler Robustness and reliability of the boiler are a guarantee, thanks to the primary exchangers made with a resistant Al-Si aluminum alloy. Guaranteed energy savings Savings in energy consumption are guaranteed up to an extra 10%, thanks to the intelligent stratification function of the 204-litre storage tank, with integrated exchanger. Characteristics Primary exchanger made with Al-Si aluminum alloy Compact solar system: in about 0.4 m² all the components necessary for the construction of a solar thermal system for DHW production, collectors excluded 3-star sanitary comfort: the maximum obtainable according to EN13203-1/2 thanks to the 200-litre stratified boiler Savings in energy consumption up to an extra 10% thanks to the intelligent management of the 200-litre stratified storage tank (with integrated solar exchanger) Connectivity via MB LAN2 module as an accessory Can be installed in any context thanks to the possibility of using fume exhaust systems with a diameter of up to 60 mm External installation, in a partially protected place, in compliance with current legislation Methane version convertible to LPG and Propane Air by means of the appropriate regulation, contact the Thermotechnical Assistance Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Seasonal heating efficiency % 94   Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 25/30 kW Nominal heating thermal power: 24.48 kW Efficiency at nominal power: 97.9% Efficiency at reduced load (30%): 103.5% Max electric power heating Watt 89 Electrical protection degree IP X5D Expansion vessel capacity 8 litres Quantity of hot water with Δt=25°C: 17 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 780x400x365 ; 38kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control Mynute Green E - ErP System energy class A+ (in combination with external probe and Rec 08 remote panel) Heating energy class A Energy class of the sanitary A New condensing exchanger Modulation 1:5 Flex low consumption circulator (IEE≤0.20) Ducting with flue Ø 50 mm   The new Mynute Green E range is designed following the ecodesign indications provided for by the European ErP Directive and is made up of two combined models and a heating only model. The combined versions have a thermal capacity of 20-25 kW and 25-30 kW, values ​​which refer respectively to heating and DHW; similarly, the heating only version has a thermal capacity of 25-30 kW. The range offers as standard the new front access condensing exchanger with improved efficiency (94% seasonal efficiency), the low consumption modulating circulator, the predisposition for the clapet kit (optional) to be used for pressurized flues and the high pressure fan. prevalence to be able to carry out the ducting of flues with Ø 60 or Ø 50 exhausts. Mynute Green E: high energy efficiency, low gas consumption and low emissions. The entry into force of the European Directive ErP (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Compulsory labeling provides greater transparency on the characteristics of the products which can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2 ) by 20%, increasing by 20 % use of renewable energies and reduce energy consumption by 20% in EU countries. The new Beretta condenser exchanger with front access The Mynute Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. With the new Beretta condensing exchanger, boiler performance improves up to an average seasonal efficiency of 94%. Mynute Green E, the elegant The new Mynute Green E is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to easily select all the functions necessary for using and setting the boiler. Flex modulating circulators: optimized performance, low consumption Mynute Green E uses a synchronous modulating circulator with low energy consumption, as required by the European ErP Directive. Thanks to this new technology, the electric motor of the circulator offers an Energy Effi ciency Index of less than 0.20, which means significantly reduced electricity consumption. The new circulator works proportionally to the power supplied by the boiler, thus contributing to a further reduction in electricity consumption. In case of need on the heating system, it is possible to change the head without having to replace the standard circulator with a high head one, the name “Flex” derives from this feature. Up to 49 meters of ducting With Mynute Green E it is possible to comfortably intubate even the most "difficult" flues thanks to the approval for flue Ø 50mm. The main 50mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. Characteristics: MYNUTE GREEN E + external probe + REC 08 remote control forms a class A+ system Designed according to the ecodesign indications provided for by the European ErP Directive Energy Class > heating (class A) > DHW profile XL (class A) Seasonal heating efficiency 94% Low polluting emissions: class 5 (UNI EN 483) New high-flow aluminum condensing exchanger with front access Standard thermoregulation (optional external probe) ErP boilers with low consumption modulating circulator (EEI0.20) modifiable up to 7m head Hydraulic connections cover (optional) Possibility of intubating flues with the special flue ø 60 in PP and ø 50 in PP (only ErP boilers) Template, plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres     Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Riello condensing boiler Family 30 KIS Low NOx complete with methane or LPG fume exhaust kit class A - NEW Energy class in heating A Energy class in sanitary A XL load profile Heating Nominal heat input kW 25.0 Nominal thermal power (80°-60°) kW 24.4 Expansion vessel L 10 Sanitary Nominal heat input kW 30 Nominal thermal power** kW 31.5 Maximum pressure bar 8 Hot water production with T+25 °C l/min 18.1 NOx class 6 Dimensions Dimensions (H***xLxP) mm 822x470x275; 39 kgs Methane or LPG power supply: the boiler is self-adapting without the need for conversion kits Riello presents the New Family New stainless steel heat exchanger Riello has always designed its products with care and dedication. Continuous improvement leads today to the evolution of the Family condensing range, starting from its primary element: the exchanger. The new Family exchanger is made of stainless steel, with a smooth tube with a large section to guarantee the best efficiency and cleanliness over time. Access remains from the front, to facilitate maintenance operations. Riello has also optimized the DHW exchanger by adopting the most advanced fluid-thermodynamic analysis and simulation techniques to obtain the best performance and maximum comfort for the user in terms of waiting times and temperature stability during sampling, compared to a boiler traditional MAXIMUM POSSIBLE LOAD PROFILE IN RELATION TO THE TYPE AND POWER OF THE GENERATOR, UP TO XXL IN THE CASE OF 35 KW FAMILY. SANITARY ENERGY EFFICIENCY CLASS A, THE MAXIMUM VALUE CURRENTLY PROVIDED BY EU REGULATION 811/2013 FOR COMBINED GENERATORS (TRADITIONAL BOILER CLASS B). REDUCTION OF GAS CONSUMPTION COMPARED WITH A TRA ADTIONAL BOILER BY APPROXIMATELY 10%, ACCORDING TO EN13203-2. ALMOST NULL WAITING TIME FOR HOT WATER (< 1 SECOND) WITH DOMESTIC HOT WATER PRE-HEATING FUNCTION ACTIVE (TRADITIONAL BOILER ABOUT 40 SECONDS). Emissions always under control The new Family is equipped with the intelligent ACC combustion control system, which guarantees that the process always takes place in an optimal manner in any condition, thanks to the modulating gas valve and the ionization electrode. Thanks to the ACC, the Family is able to automatically adapt to the fuel (methane or LPG) without resorting to specific codes or accessory conversion kits. Family also reacts to the variation of the fuel title and to the pressure drops on the flue gas side. The ACC system detects the excess air value and intervenes by modulating the air/gas mixture to always keep it within the optimal parameters. The ACC system also simplifies installation. In the ignition phase, it does not require calibration and it is sufficient to select the type of combustible gas used by the boiler via the interface, if different from the default one (methane). Since the system keeps the value of the CO2 produced constant, even the smoke control during the ignition phase is no longer necessary for the correct functioning of the product. Controlling combustion also means guaranteeing constant emissions, which are always well below the limits set by the law. In fact, if the process takes place in an optimal manner, the gases produced will also have the best theoretical composition with respect to the other conditions. Control panel and functions Even clearer, more intuitive and easier to use, it integrates elegantly into the aesthetics of the machine. The large backlit display, the raised keys and the interface enriched with explanatory texts and icons help the user and the installer in navigation. Through the panel it is possible to view the operating status, carry out the programming and access the regulation of the boiler and system. The Family display is equipped with the new "Color Bar" which informs the user at a glance on the operating status of the boiler. In the event of anomalies, it is possible to immediately understand if a problem is critical and whether to request the intervention of technical assistance. GREEN Regular operation. The system is satisfying domestic hot water/heating requests or carrying out other automatic operations. A scrolling text at the bottom describes the function active at that moment. RED Presence of blocking anomalies that require an intervention by the Technical Assistance. An error triangle on the display gives access to the details of the anomaly. YELLOW Presence of anomalies that can potentially be solved by the user which allow even partial operation of the product. An error triangle on the display gives access to the details of the anomaly. GRAY The system is ready to serve any requests. No operation in progress and anomaly detected. RiCloud - Comfort at your fingertips The RiCLOUD intelligent remote control allows you to manage the comfort of your home in a simple and intuitive way, even when you are away from home. Through the dedicated app it is in fact possible to check the status of the heating system, but also to program the switching on and off, temperature and operating times of the boiler directly from your smartphone or tablet. It is possible to manage up to 8 different zones, each controlled by its own RiCLOUD. RiCLOUD can also be installed in total wireless mode using a radio frequency receiver, available as an accessory, thus avoiding any electrical or masonry intervention. Many needs, one solution INTERIOR Inside the home, thanks to an elegant aesthetic that allows it to be inserted pleasantly into any environment . OUTDOOR Outdoors in a partially protected place, thanks to the IPX5D degree of protection and the standard antifreeze function down to -0 °C , without additional heaters. BUILT- IN Inside a built-in box or wall unit, thanks to its compact dimensions (25 kW model). Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Product code: 3310616 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating nominal heat input max/min (Hi): 28/3.0 kW DHW nominal heat input max/min (Hi): 30.0/3.5 kW Performance Stars **** Expansion tank capacity 8 l Instantaneous quantity of hot water (∆T=25 K): l/min 17.2 Domestic water pressure max/min bar 7.0/0.2 Electrical characteristics Supply voltage/frequency: V/Hz 230/50 IP X5D degree of protection Dimensions Weight: 32.3kg General characteristics AIM ADVANCE Mira Advance is the condensing boiler born for the future with a powerful soul, Spin Tech, the new exchanger with a completely renewed design that offers high performance, to improve domestic comfort and adapt to every need. Maximum Performance: New single coil primary heat exchanger in stainless steel. Passage sections increased by 142% compared to the previous version. 1 m more head. Seasonal yield at 94%. Class A+ reachable with thermoregulation. Maximum Comfort Modulation ratio 1:10. Electronic combustion control E-Burning System. SRA function. Gas transformation from the technical menu without the need for a kit. Ready for Chaffolink connectivity. Ease of Installation Installation in partially protected places. Smoke outlets 80, 60, 50 mm. Intuitive electrical connections. Energy saving and respect for the environment Up to 25% energy savings in combination with Expert Control and the SRA function. Up to 35% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015 , the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less