Technical features NB: In the absence of the product, the new VMI 30 model will be shipped ErP energy class (Heating and DHW): class A Sanitary load profile - XL For heating and domestic hot water production Forced draft sealed chamber Nominal thermal power in sanitary kW 30 DHW nominal heat input kW 30.6 Performance stars (according to Dir. 92/42CEE) - **** Consumption at nominal power Natural gas m3 /h 3.2 Expansion vessel capacity 10 l Maximum water content in the system l 180 Storage tank setting temperature °C 35 - 65 Boiler nominal volume l 20 Minimum water flow l/min 1.5 Hot water withdrawal capacity (ΔT = 30K) l/10min 180 Domestic hot water comfort stars (prEN 13203) - *** Dimensions (hxpxl) mm 720x553x440; 57kg Power supply V/Hz 230/50 Total electric power W 100 Sound power dBA 50 IP degree of protection IP X4 D NOx class - 5 Version: CNG (0010019530) To view more product information CLICK HERE General characteristics Vaillant condensing boiler  With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year.    ecoTEC PLUS with boiler   Little space and a large family? ecoTEC plus with built-in wall-mounted boiler is the boiler designed to satisfy a high demand for hot water when spaces do not allow for the installation of external boilers.   The VMW ecoTEC plus with actoSTOR CL 20 S integrable storage tank are available in power ratings of: 30 and 34 kW. This stratification boiler is a real hot water reserve that can be installed very easily and quickly directly between the wall and the boiler. An exceptional solution that ensures the quantity of water needed is always available and without sudden changes in temperature. The boiler system with storage tank is very simple to assemble: first install the actoSTOR CL wall-mounted storage tank and the related pipes supplied for domestic water, then hang the ecoTEC plus VMW wall-mounted boiler on the storage tank. The dimensions are very small 70cm high, 44cm wide and 55cm deep. The stratification storage tank guarantees the same performance as a storage tank with a 60-litre coil but with considerably reduced spaces. The combination with ecoTEC plus allows you to exclude the storage tank functionality by making the boiler work instantaneously; this allows a considerable saving on gas consumption. New electronics and a very high efficiency pump make ecoTEC plus the wall-mounted condensing boiler that consumes less on the European market. ecoTEC plus is compatible with all Vaillant components and accessories already on the market. The new design is simple and intuitive.   Characteristics: Boiler ready for 2015 regulations ErP: class A Boiler with integrable storage tank Power modulation 1:8 10l expansion vessel High efficiency modulating pump (class A) Primary heat exchanger in steel High efficiency in the production of hot water up to 199 liters in the first 10' High DHW comfort Compact stratification storage **** Heating efficiency ELGA combustion system Ecodesign Directive (ErP) 2015 How to be ready for new EU legislation   What will happen from 26 September 2015? From this date it will no longer be possible to produce traditional forced draft boilers. Instead, it will be possible to continue producing condensing boilers and traditional open chamber boilers equipped with high-efficiency pumps and compliant with the new ErP requirements such as emission, noise and efficiency levels. In particular, the installation of traditional open chamber boilers will only be possible to replace old boilers installed in multi-family buildings which discharge the fumes into branched collective flues (CCR). Products placed on the market before 09/26/2015 that do not comply with the requirements of the new directive, such as traditional forced draft boilers and boilers not equipped with a high efficiency pump, can still be purchased, sold and installed.   ErP and ELD: what do they mean and how are they different?  ErP : The EU has issued new obligations for Energy Using Products (ErP). The new directive, known as the Ecodesign directive, prescribes minimum efficiency requirements and emission limits for appliances that produce heating and domestic hot water. The Ecodesign directive is aimed at two categories of products relevant to installers and resellers in the sector: - Category 1 Includes space heating appliances: electric, gas, oil, combined boilers, heat pumps and cogenerators up to 400 kW. - Category 2 Includes appliances for the production of domestic hot water: electric, gas, diesel, heat pumps for DHW, solar systems up to 400 kW and boilers up to 2000 litres.  ELD: in addition to the ErP directive, the EU has also introduced mandatory energy labeling for the same type of appliances up to 70 kW and boilers up to 500 litres. The energy labeling directive is called ELD and requires that new products and systems for heating and the production of domestic hot water are labeled with an indication of their energy efficiency class. By combining the products and components, for example by adding a temperature control unit, the energy classification of the system can be increased, which will be calculated by the installer and indicated on the package label.  Let's take a look at the new labels...        When and how will the new rules apply? On 26 September 2015 the new rules will come into effect. Until then, neither manufacturers, retailers or installers have to comply with the new Ecodesign or labeling provisions. Once the new rules come into effect, manufacturers will only be able to manufacture products that comply with the new Ecodesign requirements, and will be required to supply an energy label with the products     Why push condensing technology right away?   For the energy requalification of individual homes, the 2007 Budget Law was extended until 31 December 2015. The request for a 65% tax deduction concerns, for example, the replacement of a traditional boiler with a condensing boiler.     What will Vaillant support be?   7 year guarantee   The 7-year guarantee on new boilers is another excellent reason to offer Vaillant to your customers. In addition, know that by replacing a Vaillant boiler over 15 years old with a new generation one, the warranty extension will be provided free of charge by the Vaillant Official Technical Assistance Center against a maintenance contract. Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.

Read more less

Biasi ac condensing boiler complete with LPG Low NOx ErP Fume Exhaust Kit - NEW Model BASIC COND 30S DHW nominal heat input kW (kcal/h) 31.0 (26655) Nominal heat input * heating kW (kcal/h) 26.0 (22356) Maximum useful power in heating 60/80° kW (kcal/h) 25.4 (1840) Useful power in domestic hot water 60/80° kW (kcal/h) ) 30.3 (26053) Efficiency at 100% load (50/30 °C) % 107.3 Sanitary flow rate ?t =25°K l/min 17.6 NOx class 6 LPG code 10304.2029.0 Dimensions HxWxD mm 703x400x325 BASIC COND Basica Cond Basica Cond completes the BIASI range with premixed condensing: perfect for radiator systems and suitable for radiant systems with mixing groups. Basica is the compact condensing boiler that ensures high efficiency, low consumption and respect for the environment. Available for heating and domestic hot water production, in power ratings of 25 and 30 kW. Main features Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion - Total premix burner, stainless steel (Class NOx 6) - Modulation 1:5 CNG and also LPG - Sanitary plate heat exchanger in stainless steel - 8 liter expansion vessel - High efficiency pump with low energy consumption - Can be installed in a partially protected place - Integration with BIASI solar systems, using a solar kit - Analog pressure reading - Arrangement for remote control and external probe High circulation single coil primary heat exchanger Biasi introduces on the market the new stainless steel heat exchanger for condensing boilers: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single strip of stainless steel to produce the coil, including inlet/outlet fittings, the following benefits are achieved: - The accumulation of dirt and debris is avoided - The water flow rate is constant, guaranteeing a higher average life of the product - Reduction of load losses with optimized circuit. The ease of cleaning and the sturdiness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. Included in delivery Boiler support bracket and paper template Boiler power cable Condensate collection siphon Quick instruction to the user. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history The display operates in the following modes: INFO – information available on the operating status and error history FREE programming – programmable parameters for generator/system adjustment and User SET INSTALLER programming - generator parameters ASSISTANCE programming - Authorized Assistance Center parameters commands The Basica Cond Range has the choice of 2 class V remote controls (they allow deduction at 65), in the Base and Top version with weekly chronothermostat functions with up to 4 programmable periods with independent temperatures, in addition to the remote control of all the information of the boiler display. Product Guarantee: All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Riello FAMILY CX 30 KIS condensing boiler complete with Low NOx methane fume exhaust kit - NEW ErP technical data Energy class A XL load profile NOx class 6 Warm-up exercise characteristics Nominal heat input kW 25 Nominal thermal power (80°/60°) kW 24.33 Maximum pressure bar 3 Features exercise in sanitary Nominal heat input kW 30.00 Nominal thermal power (*) kW 31.50 Maximum pressure bar 8 Electrical data Supply voltage V-Hz 230-50 IP X5D degree of protection Dimensions WxDxH mm 470x350x740 New Family The new Family is the Riello solution for the most demanding user. The primary exchanger, entirely made of stainless steel, guarantees maximum efficiency and reliability over time and the new optimized sanitary exchanger ensures exceptional comfort and the best class of merit (class A). The new Family is available with powers of 25, 30 and 35 kW, in instantaneous combined and heating only versions. – ACC self-adaptive electronic combustion control – Range Rated Approval – Possibility of integration in hybrid systems – New panel with color display and intelligent system filling function – 10 liter expansion tank – Low consumption modulating circulator – Modulation ratio 1:8 – Standard flue gas flange with dedicated flue system – Clapet valve and SRD device as standard – Standard thermoregulation in combination with the external probe, available as an accessory – Possibility of recessed installation (model 25 KIS) and outdoors in partially protected places (IPX5D) – Ease of installation and wide choice of accessories - Primary heat exchanger in stainless steel - High performance sanitary exchanger - Self-adaptive electronic combustion control - Class 6 NOx Combined and heating only models, MTN and LPG compatible Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview VAILLANT ecoTEC PLUS CONDENSING BOILER VMW 306/5-5 + vSMART WiFi COMPLETE WITH FUME KIT - NEW ErP 2015 METHANE Cod. 0020222965 Technical specifications For heating and domestic hot waterÿ Forced draft sealed chamber Nominal heat input in sanitarywarekW 30 ErP energy class (Heating and DHW): class A Stars of yield (according to Dir. 92/42CEE) - **** Domestic hot water production (T = 30K) 14.3 lt Domestic hot water comfort stars (prEN 13203) - *** Expansion tank capacity 10 l Massimcontenutd?Ó?water in plantl 180 Dimensions (hxpxl) mm 720 x 338 x 440 Total electric power/pump (max speed) W 80/35 NOx class - 5 Adjustable in wi-fi from smartphone ThermostatvSMART as standard Version:ÿMETHANEÿ Features list Vaillant condensing boilerÿ With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. Tuttquestentril 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for energy-using equipment, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes in the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation even at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS ecoTEC plus the excellence of wall-mounted condensing boilers minimum consumption, maximum efficiency and versatility TheÿecoTEC plus series, wall-mounted condensing boiler of the latest generation, conceived to guarantee maximum energy savings and maximum comfort and designed to satisfyÿthe requirements of European regulationsÿconcerning energy efficiency which will enter into force inÿSeptember 2015. In addition, all the new products and systems for heating and water production hot water heaters must be labeled with an indication of their energy efficiency class. TheÿecoTEC plusÿlabeling signals theÿclass A. ecoTEC plusÿreaches this result easily because, in addition to the typical elements of Vaillant boilers, it has new completely innovative components: the combustion management system (ELGA), which, skilfully mixing air and gas, results in a reduction in gas consumption, new electronics and the very high efficiency to ensure considerable savings in electricity. For example, the electricity consumption of the boiler in stand-by is less than 2Watt (less than half of a working radio). ecoTEC plusÿguarantees maximum comfort: the boiler supplies immediately available hot water without sudden changes in temperature. Thanks to its small dimensions (70 cm high, 44 cm wide and 35 cm deep)ÿecoTEC plusÿ can be easily installed on any wall. Today it is possible to install it outdoors where the climate is mild even in winter. ecoTEC plusÿhas, in fact, also an anti-gel device which allows it to resist up to temperatures that reach -5°C. The newÿsimple and intuitive design, thanks to the display with clear text and backlighting, makes the boiler functional, allowing the user easy setting and simple control. ecoTEC plus compatible with all Vaillant components and accessories already on the market. Features:ÿ Boiler ready for 2015 regulations ErP: class A Preheat DHWÿ *** DHW comfortÿ Antigel-5øC as standard **** Efficiency in heating Modulation 1:8ÿ Modulating pump (Class A) Primary heat exchanger Vasexpansion 10 lÿ ELGA combustion system transfer kit from methane propan supplied WiFi programming from smartphone tablet wherever you are with vSMART and App vSMART VaillantÿvSMARTÿ the advanced WiFi thermoregulation system that allows you to configure the comfort of your home at any time with a simple click on your smartphone tablet. The benefits of vSMART are not limited to convenience. Using andvSMART you drastically reduce the start/stop cycles of the boiler thus allowing you to save on gas and electricity and to extend the life of your appliance. vSMARTÿtransforms your smartphone tablet into a remote control system for your heating. Wherever you are and whatever you are doing, you will be able to control and adjust the comfort of your home in extremely intuitive mod-rapid using your WiFi network. Download the free ÿvSMARTÿapp from the tuStore. To download the App, simply enter the tuStore, search for vSMART and start the download. The Vaillant vSMART App is available for iOS and Android systems. vSMARTÿ Designed to ensure comfort and extreme ease of use. You can install it on the wall by connecting it to the electricity supply and place it where you prefer using common AA + batteries. Elegant and essential, it integrates perfectly into any environment. One device to save energy for others. With vSMART you can - Control heating and domestic hot water via App.ÿ - Have 30 pre-configured and customizable standard profiles available.ÿ - Monitor energy efficiency at all times.ÿ - Control the heating systems of several homes (e.g. two flats, two houses).ÿ - Check the historical data of temperature, mode and hours of operation.ÿ - Regulate the temperature based on climate data collected from the internet.ÿ - Quickly set the function or Away from Home? or Antifreeze? for greater savings.ÿ - Take advantage of the self-learning function that recognizes your programming over time to make your life even easier. The new EU legislation Starting from 26 September 2015 it is no longer possible to produce traditional forced draft boilers. Instead, it will be possible to continue producing condensing boilers and traditional open chamber boilers equipped with high efficiency pumps and compliant with the new ErP requirements such as emission levels, noise levels and efficiency. In particular, the installation of traditional open chamber boilers will only be possible in replacement of old boilers installed in multi-family buildings which discharge fumes into branched collective flues (CCR). Products placed on the market before 26/09/2015 that do not comply with the requirements of the new directive, such as traditional forced draft boilers and boilers not equipped with a high efficiency pump, can still be purchased, sold and installed. ErP and ELD: what they mean and how they differ ErP: The EU has issued new obligations for Energy Using Products (ErP). The new directive, known as the Ecodesign directive, prescribes minimum efficiency requirements and emission limits for appliances that produce heating and domestic hot water. The Ecodesign directive addresses two relevant product categories for installers and retailers in the sector: -ÿCategory 1ÿIncludes space heating appliances: electric, gas, oil, combined boilers, heat pumps and cogenerators up to 400 kW. -ÿCategory 2ÿIncludes appliances for the production of domestic hot water: electric, gas, diesel, heat pumps for DHW, solar systems up to 400 kW and boilers up to 2000 litres. ELD:ÿIn addition to the ErP directive, the EU has also introduced mandatory energy labeling for the same types of appliances up to 70 kW and boilers up to 500 litres. The energy labeling directive is called ELD and requires that new products and systems for heating and domestic hot water production are labeled with an indication of their energy efficiency class. By combining products and components, for example by adding a temperature control unit, the energy classification of the system can be increased, which will be calculated by the installer and indicated on the package label. 7 year guarantee The 7-year guarantee on new boilers is another excellent reason to offer Vaillant to your customers. In addition, know that by replacing a Vaillant boiler over 15 years old with a new generation one, the warranty extension will be provided free of charge by the Official Vaillant Technical Assistance Center against a maintenance contract. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS BORN WITH METHANE. THEREFORE, THE STANDARD TRANSFORMATION KIT WILL BE SUPPLIED. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Technical features Product code: 3301022 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal thermal power kW 28 Annual energy consumption in heating 50 gj Annual electricity consumption 42 kWh Seasonal space heating energy efficiency % 94 Water heating energy efficiency % 82 Sound power level inside 51 dB DHW flow rate ∆T 25 °C (l/min) 17.4 Dimensions 24 kW mm (HxWxD) 745 x 400 x 315 Indoor installation and partially protected places Power supply: LPG Functionality: Wi-Fi optional XtraTech™ stainless steel primary exchanger AUTO, Comfort functions Indoor installation and partially protected places XtraTech™ is the new exclusive* Ariston stainless steel heat exchanger, the heart of the ONE condensing boilers, developed to guarantee reliability and performance over time. Increased passage sections: +142% compared to the previous exchanger. Higher prevalence, lower risk of clogging, better performance. Every day, as if it were the first. Every single component has been designed to guarantee performance and durability over time: Ariston guarantee, shown in each component. Every single component has been rigorously tested and controlled on the production line. 100% of the boilers are tested again before being shipped to our customers. The best materials have been selected, to work for a long time even in the most critical situations Always connected with Ariston NET Wherever you are, always within reach of your Smartphone. Managing the comfort of your home has never been easier! Wherever you are, you can control the climate in your home using your smartphone. Use only the energy it needs. Easy to manage weekly time programming, directly from the app. Also, choose the savings "leaflet" for a real reduction in bill costs! Technical support always ON. Thanks to the innovative remote control system, the app warns your customer in case of malfunctions. By signing a maintenance contract, the Assistance Center will be able to intervene in the event of breakdowns, even remotely. Customer serenity is at the heart of Ariston NET. Absolute efficiency: Thermoregulation in class A+ The ONE condensing boilers achieve very high seasonal performance and thanks to the thermoregulation they reach class A+! Alteas and Genus ONE are also equipped with the innovative IGNITION system, which makes combustion always perfect thanks to the electronic control. Gas transformation? No problem, from the technical menu in one touch. Total Comfort: Innovative functions to meet your needs ONE is equipped with an innovative set of smart functions to guarantee comfort every day with minimum waste of energy. Auto function: Patented function that allows you to automatically optimize the operation of the boiler, eliminating continuous switching on and off, reducing the stress on the components to a minimum. Comfort function: Hot water without any waiting! Lots of water with minimum energy consumption. Integrated Programming: Weekly hourly programming integrated into Alteas and Genus ONE products. Care function: Automatic reminder of routine maintenance. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE PRODUCT IS NEW AND 100% WORKING, BUT IT HAS DENT ON THE SIDE, THE DISPLAY IS SCRATCHED AND A SLIGHT CRACK (SEE PHOTO NEXT TO THE MAIN IMAGE) Technical features Energy class in heating: A Energy class in sanitary: A Load profile: XL Heating performance: Thermal input (min./max): 4.3/31.1 kW Useful power (min./max.): 3.9/30.0 kW Useful thermal efficiency: 98.0 % Idle efficiency (60/80°C): 91.1 / 82% Max/min useful heating power (80°C-60°C): 27.4/3.9 kW Performance stars (dir. 92/42/EEC): **** Healthcare performance: Thermal input (min./max): 4.3/33.3 kW DHW thermal power (max/min): 24.9/2.4 kW Heating circuit: Expansion vessel pre-charge pressure: 1 bar Maximum heating pressure: 3 bar Expansion tank capacity: 8 L Min/max heating temperature (high temperature range): 35 / 82 °C Min/max heating temperature (low temperature range): 20 / 45 °C Healthcare Circuit: Min/max domestic hot water temperature: 36 / 90 °C Specific flow rate in sanitary mode (10 min. with ∆T=30°C: 14.5 l/min Instantaneous quantity of hot water ∆T=25°C: 17.4 l/min Instantaneous quantity of hot water ∆T=35°C: 12.5 l/min Sanitary comfort stars (EN13203): *** Minimum withdrawal of hot water: 2 l/min Max/min domestic water pressure: 7.0 / 0.2 bar Electrical data: Protection index IPX5D Class 6 NOx Energy efficiency index of the circulator: EEI ≤ 0.23 Minimum ambient temperature of use: >0°C Total absorbed electric power: 80 W Power supply: METHANE (G20/G30) Dimensions: (HxWxD): 745x400x385mm; Weight: 29.7kg Pigma is the new CHAFFOTEAUX boiler, which is part of the Advance Range, resulting in the category leader with a completely renewed design, using the innovative SpinTech exchanger, electronic combustion control, integrated Chaffolink connectivity and Expert Control and external probe as standard, guaranteeing extremely high performance with extremely low fuel consumption. Can be installed in partially protected places. SpinTech features: Exchanger that works with a stainless steel monospiral New single coil primary heat exchanger in stainless steel Passage sections increased by 142% compared to the previous version 1 m more head Seasonal yield at 94% Class A+ thanks to the standard thermoregulation accessories Performance certified by the TÜV RHEINLAND Group. Give Comfort: Modulation ratio 1:7 Optimized internal silencer SRA function Gas transformation with kit included as standard Ready for Chaffolink connectivity Advantages: Installation in partially protected places Smoke outlets 80, 60, 50 mm Intuitive electrical connections Up to 20% energy savings in combination with Expert Control and the SRA function Up to 30% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. Reduced polluting emissions, NOx class 6.

Read more less

Technical features Product code: 3310616 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating nominal heat input max/min (Hi): 28/3.0 kW DHW nominal heat input max/min (Hi): 30.0/3.5 kW Performance Stars **** Expansion tank capacity 8 l Instantaneous quantity of hot water (∆T=25 K): l/min 17.2 Domestic water pressure max/min bar 7.0/0.2 Electrical characteristics Supply voltage/frequency: V/Hz 230/50 IP X5D degree of protection Dimensions Weight: 32.3kg General characteristics AIM ADVANCE Mira Advance is the condensing boiler born for the future with a powerful soul, Spin Tech, the new exchanger with a completely renewed design that offers high performance, to improve domestic comfort and adapt to every need. Maximum Performance: New single coil primary heat exchanger in stainless steel. Passage sections increased by 142% compared to the previous version. 1 m more head. Seasonal yield at 94%. Class A+ reachable with thermoregulation. Maximum Comfort Modulation ratio 1:10. Electronic combustion control E-Burning System. SRA function. Gas transformation from the technical menu without the need for a kit. Ready for Chaffolink connectivity. Ease of Installation Installation in partially protected places. Smoke outlets 80, 60, 50 mm. Intuitive electrical connections. Energy saving and respect for the environment Up to 25% energy savings in combination with Expert Control and the SRA function. Up to 35% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015 , the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

SAVIO actaDENS 30 S condensing boiler complete with low NOx methane fume exhaust kit - News Code 10304.2029.0 Acta Dens model Performance DHW nominal heat input kW (kcal/h) 31.0 (26655) Nominal heat input * heating kW (kcal/h) ) 26.0 (22356) Maximum useful power in heating 60/80° kW (kcal/h) 25.4 (21840) Useful power in DHW 60/80° kW (kcal/h) 30.3 (26053) Efficiency at 100% load (50/30 °C) % 107.3 Sanitary flow rate ∆t =25°K l/min 17.6 8 liter expansion tank NOx class 6 Dimensions Dimensions HxWxD mm 703x400x325 actaDENS Acta Dens completes the Savio range with premixed condensing: perfect for radiator systems and suitable for radiant systems with mixing groups. ActaDens is the compact condensing boiler that ensures high yields, low consumption and respect for the environment. Available for heating and domestic hot water production, in power ratings of 25 and 30 kW. Main features Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion Total premix burner, stainless steel (Nox class 6) Modulation 1:5 CNG and also LPG Sanitary plate heat exchanger in stainless steel 8 liter expansion vessel High efficiency pump with low energy consumption Can be installed in a partially protected place Integration with SAVIO solar systems, using a solar kit Analog pressure reading Arrangement for remote control and external probe High circulation single coil primary heat exchanger Savio introduces the new stainless steel heat exchanger for condensing boilers to the market: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. Using a single stainless steel strip to produce the coil, including inlet / outlet connections, the following advantages are obtained: The accumulation of dirt and debris is avoided The water flow is uniformly distributed and guarantees a homogeneous heat exchange Reduction of pressure drops with optimized circuit. The ease of cleaning and the robustness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. Control panel: Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history The display operates in the following modes: INFO – information available on the operating status and error history FREE programming – programmable parameters for generator/system adjustment and User SET INSTALLER programming - generator parameters ASSISTANCE programming - Authorized Assistance Center parameters Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Riello Residence Condens 30 kis condensing boiler complete with LPG Low NOx flue gas kit class A - NEW Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Heating/DHW operating characteristics Heating nominal heat input kW 20 Nominal thermal power (80°-60°) heat kW 19.5 Maximum heating pressure bar 3 DHW nominal heat input kW 25 Nominal thermal power* sanitary kW 26.3 Hot water production with t+25 °cl/min 15.1 NOx class 5 Dimensions HxWxD mm 740x420x350 Electrical data Total electric power (pmax heating) W 75 Supply voltage V - Hz 230 - 50 IP X5D degree of protection Power supply: LPG (It self-adapts without using external kits) RESIDENCE CONDENS RIELLO PRESENTS RESIDENCE THE NEW RANGE OF CONDENSING BOILERS NEW EXCHANGER Wrapped stainless steel primary exchanger. Efficiency and reliability in the heart of the Residence. DOMESTIC COMFORT FUNCTION Domestic water pre-heating with Touch&Go function for activation upon request directly from the drawing tap. ACTIVE COMBUSTION CONTROL Advanced electronic combustion control system which constantly monitors combustion to obtain constantly optimized consumption and emissions. DIGITAL USER INTERFACE Simple and intuitive backlit LCD display. Ease of setting thanks to the silk-screened keys dedicated to the individual user functions. MODULATING CIRCULATOR High efficiency circulator with flow rate modulation and regulation logic that can be set between different modes according to the type of system. HIGH EFFICIENCY The high efficiency of the primary exchanger, the modulating circulator and the continuous control of the combustion parameters guarantee very low consumption even after years of operation. QUICK INSTALLATION Speed ​​and ease of installation thanks to the compact dimensions, accessibility of the components and external electrical connections. UNIQUE VERSION METHANE - LPG Dedicated codes are no longer necessary in the case of LPG because Residence is able to automatically adapt its operation to the type of fuel with rapid setting from the display. FLEXIBLE INSTALLATION The characteristics of Residence and its compact dimensions make it the ideal solution for both indoor and recessed installation (model 25 KIS only) or outdoors in a partially protected place. RESIDENCE, HEART OF STEEL The new RESIDENCE exchanger is made of stainless steel, with a smooth tube with a large section to guarantee the best efficiency and cleanliness over time. NEW PRIMARY EXCHANGER IN STAINLESS STEEL The single coil geometry (hydraulic circuit in series) guarantees constant flow in all sections of the exchanger and intrinsically prevents clogging. Front access facilitates periodic maintenance and cleaning of the combustion chamber. SELF-ADAPTING ELECTRONIC COMBUSTION CONTROL The new Residence is equipped with the intelligent ACC combustion control system, which guarantees that the process always takes place in an optimal manner in any condition, thanks to the modulating gas valve and the ionization electrode. Thanks to the ACC, Residence is able to automatically adapt to the fuel (methane or LPG) without resorting to specific codes or accessory conversion kits. Residence also reacts to the variation of the fuel title and to the pressure drops on the flue gas side. The ACC system detects the excess air value and intervenes by modulating the mixture. The ACC system also simplifies installation. During ignition, it does not require calibration and it is sufficient to select the type of combustible gas used by the boiler via the interface, if different from the default one (methane). Since the system keeps the value of the CO2 produced constant, even the smoke control during the ignition phase is no longer necessary for the correct functioning of the product. Controlling combustion also means guaranteeing constant emissions, which are always well below the limits set by the law. In fact, if the process takes place in an optimal manner, the gases produced will also have the best theoretical composition with respect to the other conditions. MANY NEEDS, ONE SOLUTION RESIDENCE IS ALWAYS THE IDEAL CHOICE THANKS TO THE TECHNICAL SOLUTIONS AND THE COMPACT DIMENSIONS, IT CAN BE USED IN ANY INSTALLATION SITUATION INTERIOR Inside the home, thanks to an elegant aesthetic that allows it to be inserted pleasantly into any environment. OUTDOOR Outdoors in a partially protected place, thanks to the IPX5D degree of protection and the accessory antifreeze heater kit RECESSED Inside a built-in box thanks to its compact dimensions (model 25 KIS only). NEW DIGITAL CONTROL Setting your own comfort for domestic hot water, air and heating is immediate thanks to the buttons with symbols dedicated to the individual functions Domestic hot water temperature setting Operating status 0FF - SUMMER - WINTER Unlock and restore alarms Information and parameters menu Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Hermann Saunier Duval THEMA CONDENS 30 kW condensing boiler complete with low NOx flue gas kit - Methane Model: Efficiency class Heating efficiency class A Sanitary efficiency class - A Sanitary load profile - XL Heating Rated power Pmin/max - 80/60°C kW 6.6 / 26.7 Efficiency Pmax % 109.2 Sanitary Rated power min/max - 60°C 6.1 / 30.6 kW Specific flow rate (DT = 30K) (EN13203) l/min 18 generals Supply gas - methane Max absorbed electric power (W) Nox class - 5 Electrical protection IPX - 5D Dimensions mm (HxLxP) 740x418x344 THEMA Condens Wall-mounted condensing boiler with pre-heating and Aquaspeed® technology. The Thema Condens range features combined methane and propane models, all equipped with a primary heat exchanger in anti-corrosion stainless steel and an 8-litre expansion tank (heating side), perfect for single-family homes. The Thema Condens range is enriched with two models: IS and AP dedicated to multi-family solutions for both single and multiple ducting. Thema Condens IS is available in two versions of 26 and 30 kW with natural gas supply and convertible to propane . The AP version, on the other hand, is only available in the 26kW methane power size. The IS version features a dedicated flue kit consisting of a flue non-return valve, 80/125 mm adapter with 87° bend and rigid section for connection directly to a single flue. In the HP version Thema Condens has a safety pressure switch and a fan with increased head which allows reaching vertical ducts up to 30 meters with self-adaptation of the required length via the system electronics. Vertical ducting with DN 50, both rigid and flexible, is also possible, which solves the problems in old flues and in those where the available space is minimal. Primary heat exchanger in anti-corrosion stainless steel Sanitary comfort ★★★ thanks to the exclusive Aquaspeed® technology Continuous domestic hot water (DHW) production up to 18 l/min Pre-heating function and DHW plate exchanger in stainless steel Solar Easy: predisposition for solar integration Warranty extension up to 5 years Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

SIME BRAVA ONE 30 HE METHANE condensing BOILER COMPLETE WITH FUME EXHAUST KIT For heating and domestic hot water production DHW thermal power kW 4.8÷28.0 Heating thermal power (50-30°C) kW 4.8÷28.0 Efficiency class (EEC 92/42): **** Continuous DHW flow rate Δt 30°c: 12.9 l/min Heating energy efficiency class: A Dimensions (h x w x d): 700 x 400 x 250 mm; 28.4kg METHANE version GOOD ONE Premixed condensing boiler Wide modulation range Stainless steel coil exchanger Extremely compact dimensions Three-piece cloak DHW management with dedicated probe Retroactive combustion control with electronic gas valve Can be installed outdoors and recessed using accessories (see page 78) 2 versions with 24.0 and 28.0 kW domestic hot water production Integrated climatic regulation Incredible dimensions for its potential The particularly compact dimensions are the most evident feature of the new Brava Slim and Brava One: 70 cm x 40 cm x 25 cm for almost all models, up to 35 kW of power. A unique result on the market! For example, comparing the condensing versions with previous models, there is an average decrease in volume of over 30% You will sleep soundly With Brava Slim and Brava One, Sime adopts the brass hydraulic group on all the boilers in the range. Brass, synonymous with quality, reliability and long life, guarantees peaceful sleep. The new hydraulic group also introduces the order of connections according to the DIN standard, adopted by the majority of European manufacturers, a further guarantee of maximum installation flexibility of Brava Slim and Brava one. For every action the perfect reaction Boiler manufacturers have always been concerned with developing the most efficient and ecological combustion. The passage of time often nullifies these efforts, lowering the quality of the combustion due to uncontrollable physical drifts. An active control of the combustion allows maintain the system within predefined efficiency, safety and emissions limits. The system is based on two fundamental components: the ignition electrode and the control electronics. The electrode, immersed in the flame, acts as a combustion control sensor providing feedback to the electronics that regulates combustion continuously. Advantages: Simple commissioning, high reliability and low maintenance over time Maximum safety in the event of poor exhaust gas evacuation or recirculation of unburnt gases (not detectable by traditional systems) Better control of combustion drifts caused by machining tolerances, oxidation and insulation losses No mechanical settings: electronic calibration of the gas valve Increased reliability by eliminating the air pressure switch in traditional combustion boilers Easier natural gas/LPG changeover via a simple parameter in condensing boilers and safe operation in the event of using the wrong gas Versatile and adaptable to any environment The extremely compact dimensions of Brava Slim and Brava One offer maximum assembly flexibility: all condensing and sealed chamber models from 25 to 35 kW are suitable for outdoor or recessed installation using simple accessories. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENZIONE , LA CALDAIA VERRA' FORNITA A METANO , PER LA TRASFORMAZIONE A GPL CONTATTARE IL CENTRO ASSISTENZA DI ZONA Caratteristiche tecniche Modello : Family 30 KIS Codice prodotto : 20187644 Alimentazione : Gpl Efficienza energetica Classe di efficienza energetica riscaldamento : A Classe di efficienza energetica sanitario : A Riscaldamento Portata termica nominale : 25,00 kW Potenza termica nominale (80°/60°) : 24,33 kW Potenza termica nominale (50°/30°) : 26,50 kW Sanitario Portata termica nominale : 25,00 kW Potenza termica nominale : 31.50 kW Rendimento di combustione : 97,6%  Performance Pressione massima : 3 bar Vaso d’espansione a membrana : 10 litri Dimensioni e peso Dimensioni (LxHxP) : 470x740x350 mm Peso : 40,0 Kg Caldaia a condensazione Riello Family La sintesi perfetta di performance e sostenibilità La nuova Family è la soluzione Riello per l'utente più esigente. Lo scambiatore primario, interamente realizzato in acciaio inox e con accessibilità frontale alla camera di combustione, garantisce la massima efficienza ed affidabilità nel tempo ed il nuovo scambiatore sanitario ottimizzato assicura un comfort eccezionale e la migliore classe di merito Hibrid Ready FAMILY nasce hybrid ready, in grado cioè di gestire direttamente, senza necessità di accessori aggiuntivi, i componenti di un sistema multi-energia, in modo efficiente ed efficace. Controllo di sistema Il pannello di controllo della nuova gamma FAMILY, attraverso il suo display a colori, semplice e intuitivo, integra ora anche la funzione di gestione diretta di un sistema multi-energia, senza la necessità di controlli esterni accessori. Scambiatore in acciaio inox Scambiatore primario in acciaio inox, con geometria a spira unica avvolta. Massima efficienza e affidabilità. Basse emissioni FAMILY è certificata Classe 6 di NOx, la migliore prevista dagli standard europei Alta efficienza Massimo comfort e minimi consumi, in riscaldamento ed in sanitario. Stabilità dell'acqua calda sanitaria Nuovo scambiatore sanitario a piastre ottimizzato, per performance al top della categoria in termini di efficienza, stabilità della temperatura e tempi di attesa. Installazione semplice e veloce Con FAMILY l’installazione e l’accesso ai componenti sono semplificati per ridurre al minimo tempo e fatica. ACC Combustion FAMILY è caratterizzata dal sistema di controllo di combustione elettronico evoluto, che monitora costantemente la combustione per ottenere consumi ed emissioni sempre ottimizzate. Pannello di controllo con nuova funzione ibrida Con la nuova gamma FAMILY, gestire un sistema ibrido è semplice e intuitivo. Il display di FAMILY, caratterizzato da un’estetica moderna ed elegante, si arricchisce infatti della funzione di gestione di sistema multi-energia. L’intelligenza del sistema ibrido, REC 10CH, integrata nell’elettronica della nuova FAMILY, offre la possibilità di gestire le sorgenti termiche a disposizione attraverso l’interfaccia utente, senza necessità di un pannello di controllo accessorio. Garanzia prodotto :  Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.

Read more less