RIELLO START IN CONDENS 25 KIS LPG CONDENSING BOILER COMPLETE WITH FUME KIT + BUILT-IN UNIT - NEW ErP Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Heating rated heat output: 19.5 kW Sanitary nominal heat input: 25 kW Sanitary nominal thermal power: 25 kW Energy efficiency (92/42/EEC) **** Useful efficiency Pn (50°/30°): 104.2% Profit return 30% (47th return): 108.9% Sealed chamber, forced draught Quantity of hot water with Δt 25°C: 14.3 l/min Dimensions (hxwxd) mm 792 x 405 x 248 ; 30 Kgs Electrical protection degree: IP X5D NOx class: 5 It can be installed flush-mounted using the special built-in unit Power supply: LPG General characteristics START IN CONDENS Yield **** Low polluting emissions Aluminum condenser, with premix burner Recessed Start IN Condens is the new Riello condensing wall-mounted proposal for small and medium-sized domestic users. The new compact aluminum condensing exchanger guarantees efficiency and reduction of polluting emissions. It can be installed flush-mounted using the special kit. It is available in version 25 (with 25 kW of DHW power and 20 kW in heating) and 29 (with 29 kW of DHW power and 25 kW in heating). Characteristics: Low consumption circulator (IEE≤0.20) "Winter with Pre-heating" function: allows the DHW exchanger to be kept at temperature, reducing waiting times during withdrawal (can be activated by the user) Remote control panel in combination with the external probe (optional) Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: MODEL OUT OF PRODUCTION, IN CASE OF UNAVAILABILITY WE WILL SEND THE NEW THEMATEK CODENSING MODEL WHICH YOU FIND AT THE FOLLOWING LINK: https://www.climaconvenienza.it/it/caldaia-hermann-saunier-duval-thematek-condensing- 25-kw-condensing-complete-with-methane-flue-kit/ HERMANN SAUNIER DUVAL SEMIATEK 4 CONDENSING BOILER 25 kW COMPLETE WITH KIT FOR METHANE FUME EXHAUST - NEW ERP Model: ErP efficiency class in heating/DHW: A Sanitary load profile: XL Type: Heating and domestic hot water Combustion chamber: sealed Heating Nominal power P min/max heating 80/60 °C: kW 5.3/19.1 Partial load efficiency 30% 40/30 °C %: 108.5 Sanitary Rated power min/max (60 °C): kW 5/25.2 Specific flow rate (∆T=25 K): l/min 14 Continuous flow rate (∆T=30 K): l/min 12 Min/max DHW temperature: 35/60 °C Electrical characteristics Total absorbed electric power: W 105 Supply voltage/frequency: V/Hz 230/50 Dimensions: Dimensions (h x w x d): 740 x 418 x 300 mm METHANE version SEMIATEK 4 CONDENSING The condensing boilers of the Semiatek 4 Condensing range are characterized by a simple and linear design. The range includes two combined models of 25 and 30 kW. Characteristics: Energy classification **** (92/42/EEC) with yields up to 109.2% Continuous domestic hot water (DHW) production up to 18 l/min Solar Easy: prepared for integration with solar systems Low NOx emissions - class 5 (EN 483) Total premix burner and primary exchanger in anti-corrosion Aluminium-Silicon alloy Automatic high efficiency circulator on 2 speeds Heating system antifreeze function Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

SAVIO INOXDENS HE 25S* Condensing Boiler Complete With Methane Fume Exhaust Kit - NEW ErP Model: INOXdens HE 25S ErP specifications Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 21.0/26.0 kW Heating/DHW maximum useful power 60°/80°C: 20.3/25.1 kW Heating/DHW maximum useful power 30°/50°C: 22.4/22.4 kW Yield name 60°/80°C: 96.6% Yield at 30% load: 107.6% Energy Efficiency ★★★★ NOx class 6 Weighted NOx: 45 mg/kWh Minimum/maximum heating temperature: 25/80°C Minimum/maximum heating pressure 3.0/0.3 bar Expansion tank capacity 7.0 l (total) Minimum/maximum domestic hot water temperature 35/60°C Maximum flow rate (ΔT=25 K)/(ΔT=35 K): 14.4/10.3 l/min Specific sanitary flow rate (ΔT=30 K): 12 l/min Voltage / Power at nominal heat input V~/ W 230/99 Degree of protection IPX5D Dimensions HxWxD 700x400x290; 31 Kgs Power supply: methane INOXDENS The perfect compact boiler for underfloor systems and radiator systems The adjustable maximum useful power parameter in heating meets the needs of modern construction without compromising the comfort required in the production of domestic hot water. In fact, this function makes it possible to limit the maximum useful power in heating, independently of the useful DHW power. INOXDENS HE is the new Savio range of wall-mounted condensing boilers: excellent performance thanks to the new heat exchanger and ease of use thanks to the digital control panel with large display. Available in the versions for heating and domestic hot water production and for heating only INOXDENS HE presents a complete range of powers, 20 and 30 kW combi models and 16 KW SV models, in the same extremely compact dimensions (700 x 400 x 290 mm). INOXDENS HE has its strong point in the innovative heat exchanger designed to provide high yields that last over time digital control panel, designed to communicate with the user in an easy and comfortable way. Like the entire Savio condensing range, INOXDENS HE allows you to obtain maximum savings from climatic thermoregulation, based on the system in which the boiler is installed. High yields (★★★★ compliant with yield directive 92/42 EEC and Legislative Decree 311/06) Sanitary comfort (★★★ EN 13203) Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion Total premix burner, built in stainless steel (Class NOx 6) Modulation 1:5 CNG and also LPG Sanitary plate heat exchanger in stainless steel 7 liter expansion tank High efficiency pump with low energy consumption Maximum power adjustable according to the system Degree of protection IPX5D Can be installed in a partially protected place Integration with Savio solar systems, using a solar kit Digital control panel with backlit display Analog pressure reading Arrangement for remote control and external probe. High regulation single coil primary heat exchanger Savio introduces the new stainless steel heat exchanger for condensing boilers to the market: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single strip of stainless steel to produce the coil, including inlet/outlet fittings, the following benefits are achieved: Accumulation of dirt and debris is avoided The water flow is uniformly distributed and guarantees a homogeneous heat exchange The water flow is constant for a longer life of the product Reduction of pressure drops with optimized circuit Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Model: rinNOVA COND PLUS E 25S Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating / DHW nominal heat input kW 21.0 / 26.0 Heating / DHW maximum useful output 60°/80°C * 20.3 / 15.1 Energy yield n° **** NOx class 6 Expansion vessel capacity 7.0 l (total) Maximum range (ΔT=25K) / (ΔT=35K) 14.5 / 10.3 Degree of protection IPX5D Dimensions HxWxD 700x400x290; 33 kgs General characteristics renew COND PLUS RinNova Cond Plus is the new BIASI range of wall-mounted condensing boilers: excellent performance thanks to the new heat exchanger and ease of use thanks to the digital control panel with display. Available in versions for heating and domestic hot water production and for heating only RinNova Cond Plus presents a complete range of powers, 20 and 30 kW combi models and 16 KW SV models, in the same extremely compact dimensions (700 x 400 x 290 mm) . RinNova Cond Plus has its strong point in the innovative heat exchanger designed to provide high yields that last over time digital control panel, designed to communicate with the user in an easy and comfortable way. Like the entire BIASI condensing range, RinNova Cond Plus allows you to obtain maximum savings from climatic thermoregulation, based on the system in which the boiler is installed Characteristics: High yields (★★★★ compliant with yield directive 92/42 EEC and Legislative Decree 311/06) Sanitary comfort (★★★ EN 13203) Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion Total premix burner, built in stainless steel (Class NOx 6) Modulation 1:5 CNG and also LPG Sanitary plate heat exchanger in stainless steel 7 liter expansion vessel High efficiency pump with low energy consumption Maximum power adjustable according to the system • IPX5D degree of protection Can be installed in a partially protected place Integration with BIASI solar systems, using a solar kit Digital control panel with backlit display Analog pressure reading Arrangement for remote control and external probe. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display and fill guide View annual maintenance expiry The display operates according to the modes: 1. INFO. Info mode displays the following information: External temperature (in case of external probe connected) K value (in case of external probe connected) Sanitary / heating temperatures chosen by the user Smoke temperatures. 2. PROGRAMMING. The programming mode allows you to change the boiler parameters. - In chimney sweep mode it is possible to test the boiler and adjust the gas valve. Thermoregulation By connecting the external probe and the remote control (optional) directly to the boiler, climatic regulation can be used. RinNova Cond Plus will adapt the system water temperature to the external climatic conditions, ensuring that the desired room temperature is reached without waste and optimizing consumption. By using the climatic regulation, the regulation efficiency is also raised, giving greater value to your home. High regulation single coil primary heat exchanger Biasi introduces on the market the new stainless steel heat exchanger for condensing boilers: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single strip of stainless steel to produce the coil, including inlet/outlet fittings, the following benefits are achieved: Accumulation of dirt and debris is avoided The water flow is uniformly distributed and guarantees a homogeneous heat exchange The water flow is constant for a longer life of the product Reduction of pressure drops with optimized circuit. The ease of cleaning and the robustness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015 , the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

BERETTA MYNUTE RAIN GREEN E 25 CSI CONDENSING BOILER COMPLETE WITH METHANE FUME EXHAUST KIT - NEW ErP Code: 20096642 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Sanitary nominal heat input: 25 kW Classification European Directive EEC 92/42: **** Quantity of hot water with Δt=25°C: 14 l/min Dimensions (hxwxd) mm 797 x 553 x 274 METHANE power supply Legend: E (ErP) C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control) Exclusive services: and Beretta offers 5 or 10 years of peace of mind thanks to the Kasko warranty extension formulas. Mynute Rain Green E - ErP The new Mynute Green E range is designed following the ecodesign indications provided for by the European ErP Directive and is made up of two combined models and a heating only model. The combined versions have a thermal capacity of 20-25 kW and 25-30 kW, values ​​which refer respectively to heating and DHW; similarly, the heating only version has a thermal capacity of 25-30 kW. The range offers as standard the new front access condensing exchanger with improved efficiency (94% seasonal efficiency), the low consumption modulating circulator, the predisposition for the clapet kit (optional) to be used for pressurized flues and the high pressure fan. prevalence to be able to carry out the ducting of flues with Ø 60 or Ø 50 exhausts. Mynute Green E: high energy efficiency, low gas consumption and low emissions. The entry into force of the European Directive ErP (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Compulsory labeling provides greater transparency on the characteristics of the products which can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2 ) by 20%, increasing by 20 % use of renewable energies and reduce energy consumption by 20% in EU countries. The new Beretta condenser exchanger with front access The Mynute Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. With the new Beretta condensing exchanger, boiler performance improves up to an average seasonal efficiency of 94%. Flex modulating circulators: optimized performance, low consumption Mynute Green E uses a synchronous modulating circulator with low energy consumption, as required by the European ErP Directive. Thanks to this new technology, the electric motor of the circulator offers an Energy Effi ciency Index of less than 0.20, which means significantly reduced electricity consumption. The new circulator works proportionally to the power supplied by the boiler, thus contributing to a further reduction in electricity consumption. In case of need on the heating system, it is possible to change the head without having to replace the standard circulator with a high head one, the name “Flex” derives from this feature. Up to 49 meters of ducting With Mynute Green E it is possible to comfortably intubate even the most "difficult" flues thanks to the approval for flue Ø 50mm. The main 50mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. The simplicity of comfort The management, simple and intuitive, favors the understanding and use of all the functions. There are two control selectors for setting the adjustment functions: heating temperature selection knob and domestic hot water knob. Boiler status indications are shown on the display. The filling of the system is carried out simply thanks to the practical filling cock and the visible control hydrometer. Characteristics: MYNUTE RAIN GREEN E + external probe + REC 08 remote control forms a class A+ system Antifreeze kit available up to -10°C (optional) ErP boilers with low consumption modulating circulator (EEI0.20) modifiable up to 7m head Low polluting emissions: class 5 (UNI EN 483) New high-flow aluminum condensing exchanger with front access Standard thermoregulation (optional external probe) Arrangement for connection to the REC 08 remote control panel (optional) Possibility of intubating flues with the special flue ø 60 in PP and ø 50 in PP (only ErP boilers) IPX5D electrical protection degree Template, plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: in the absence of the product, the new VMW 26 CS model will be shipped VAILLANT ecoTEC PLUS condensing BOILER VMW 256/5-5+ Technical features: For heating and domestic hot water production Forced draft sealed chamber Heating efficiency class A Sanitary efficiency class A Sanitary load profile XL Nominal thermal power in DHW 25.0 kW Efficiency at 30% 110.0 Performance stars (Dir. 92/42CEE) **** NOx class 5 Path : p » span Words: 712 Degree of protection IP X4 D Expansion tank capacity 10 l Domestic hot water production (ΔT = 30K) 11.9 l/min Power supply V/Hz 230/50 Dimensions HxWxD: 720-338-440 mm; 36 kgs Power supply: methane or LPG Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year.  ecoTEC PLUS VMW+ The most efficient and versatile combi condensing boiler there is. ecoTEC plus. Wall-mounted condensing boilers capable of always guaranteeing maximum efficiency and maximum comfort. This is German quality. ecoTEC plus has always been the most popular Vaillant boiler. Today it guarantees even lower consumption, a further increase in efficiency and versatility and the certainty of immediate sanitary comfort without jolts.  The best of Vaillant technology to satisfy every need Every component and every function of ecoTEC plus has been designed to combine efficiency and reduced consumption in favor of greater respect for the environment. ecoTEC plus self-adapts to your needs by always choosing the most economical solution, mixing the right amount of gas and air; all this with an electrical consumption of less than 2 Watts (less than half of a radio in operation). The combined version satisfies all comfort needs, guaranteeing both constant hot water without sudden changes in temperature and a comfortable climate. Sanitary comfort, in particular, is managed by the efficient Aqua Comfort pre-heating system which, thanks to 4 probes, controls, verifies and guarantees the immediate delivery of hot water always at the same temperature. Lots of hot water, immediately, without sudden changes is the real comfort offered by ecoTEC plus. From today it can also be installed outdoors where the climate is mild even in winter. In fact, the boiler has a standard antifreeze device which allows it to resist down to -5°C. To have heating and domestic hot water in a single solution The VMW ecoTEC plus condensing wall-mounted boilers combine the production of domestic hot water with the heating function. Unlike all the other boilers, the Vaillant ELGA system is installed inside, which expands the modulation range, but above all electronically regulates and monitors combustion to always ensure the lowest gas consumption, guaranteeing maximum efficiency. The boiler adjusts itself automatically and continuously, as if it were assisted every 30 seconds. In addition to a new, simpler and more intuitive design, the new electronics together with a very high efficiency pump make ecoTEC plus VMW+ the wall-mounted condensing boiler that consumes less on the European market. the ecoTEC plus VMW+ boiler is compatible with all Vaillant components and accessories already on the market. The dimensions are reduced 70cm high, 44cm wide and 35cm deep (identical to the previous version), the weight has been optimized making installation easier. and with vSMART... and go to Class A+ (Optional). All models of the ecoTEC plus VMW+ range have an efficiency etas = 94%. For this reason, if combined with a class VI thermoregulation (such as vSMART), they reach a system efficiency of 98% and therefore the ErP energy class in heating A+. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ARISTON GENUS PREMIUM EVO CONDENSING BOILER IN 25 EU COMPLETE WITH LPG - ErP FUME KIT Technical features Product code: 3300736 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 22/2.5 Max/min heating thermal power (80°C-60°C) kW 21.5/2.4 Efficiency at nominal heat input (60/80°C) % 97.8 Efficiency at nominal heat input (30/50°C) % 106.2 Efficiency at 30% at 30°C % 109 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Min operating temperature* °C -15 Specific flow rate in DHW (10 min. with ∆T=30°C) litres/min 12.2 Quantity of hot water ∆T=25°C litres/min 14.6 Quantity of hot water ∆T=35°C litres/min 10.4 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 78 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 1140/590/240 Extremely small dimensions to adapt to any space problem. METHANE power supply Standard: Sensys system manager with integrated time programming General characteristics Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. EVO: energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the energy certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston satisfies all the indications envisaged for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energy. Genus Premium Evo IN Genus Premium Evo In is the wall-mounted condensing boiler expressly designed for built-in installation. Small dimensions and reduced weight, its implementation is extremely simple. This without giving up the safety that distinguishes Ariston, i.e. exceptional resistance to cold (up to -15°C) and electrical protection from water and dust that reaches the highest levels (IPX5D classification). High efficiency product with low consumption thanks to the 1:10 modulation ratio and the high efficiency circulator with continuous modulation Characteristics: Built-in condensing boiler with auto function and info top Sensys system manager with integrated time programming Continuous modulation high efficiency circulator Modulation ratio 1:10 Universal built-in unit in electro-galvanized sheet metal (to be ordered with separate code) Possibility of outdoor installation thanks to all weather protection systems. Prepared for integration in system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort External probe integrated in the boiler Semi-automatic filling Circular anti-freeze, anti-limescale and anti-blocking protection Increased sanitary exchanger Cold water inlet and heating return filters Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons Acoustic comfort Acoustic comfort is further guaranteed by the introduction of the new silencer. For the Genus Premium Evo EXT thanks also to the high modulation ratio 1:10, the continuously modulating pump and the presence of side sound-absorbing panels. High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.  

Read more less

ATTENTION FOR THE GAS TRANSFORMATION, CONTACT THE AUTHORIZED AREA SERVICE CENTER IN ADVANCE BERETTA MYNUTE RAIN GREEN AND 25 CSI BOX CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ERP Code: 20096647 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Sanitary nominal heat input: 25 kW Classification European Directive EEC 92/42: **** Quantity of hot water with Δt=25°C: 14 l/min Dimensions (hxlxp) mm 1223 x 654 x 255 + 26 Net weight of boiler + box kg 39+20 METHANE power supply C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control) Exclusive services: Beretta offers 5 or 10 years of peace of mind thanks to the Kasko warranty extension formulas. Standard: BeSMART Remote Control Panel and external probe in the BOX version (class A+) General characteristics 1) Mynute Rain Green E BOX - ErP The new Mynute Rain Green E outdoor range (down to -10°C with special kits), offers three models suitable for "wall" installation and a specific version for "recessed" installation. Designed following the ecodesign indications provided for by the European ErP Directive, it is made up of combined and heating only models. The boilers have a higher power in DHW operation thus offering greater comfort. Mynute Rain Green E is equipped with the new front access condensing exchanger which allows high yields (94% seasonal yield) and with the new low consumption modulating circulator which can be configured according to the type of system. Mynute Rain Green E is compatible with the optional BeSMART WiFi Comfort Control Kit which allows remote comfort control from smartphones and tablets using special free APPs and together they form a class A+ system. Mynute Rain Green E is compatible with the new Ø 50 mm flue with which it is possible to carry out ducting up to 49 m (25 CSI and 25 RSI versions). 2) Mynute Green E: high energy efficiency, reduced gas consumption and low emissions. The entry into force of the European Directive ErP (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Compulsory labeling provides greater transparency on the characteristics of the products which can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2 ) by 20%, increasing by 20 % use of renewable energies and reduce energy consumption by 20% in EU countries. 3) The new Beretta condenser exchanger with front access The Mynute Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. With the new Beretta condensing exchanger, boiler performance improves up to an average seasonal efficiency of 94%. 4) Flex modulating circulators: optimized performance, low consumption Mynute Green E uses a synchronous modulating circulator with low energy consumption, as required by the European ErP Directive. Thanks to this new technology, the electric motor of the circulator offers an Energy Effi ciency Index of less than 0.20, which means significantly reduced electricity consumption. The new circulator works proportionally to the power supplied by the boiler, thus contributing to a further reduction in electricity consumption. In case of need on the heating system, it is possible to change the head without having to replace the standard circulator with a high head one, the name “Flex” derives from this feature. Up to 49 meters of ducting With Mynute Green E it is possible to comfortably intubate even the most "difficult" flues thanks to the approval for flue Ø 50mm. The main 50mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. The simplicity of comfort The management, simple and intuitive, favors the understanding and use of all the functions. There are two control selectors for setting the adjustment functions: heating temperature selection knob and domestic hot water knob. Boiler status indications are shown on the display. The filling of the system is carried out simply thanks to the practical filling cock and the visible control hydrometer. [ 1 ] Digital display [ 2 ] Selector on/off/summer/winter/reset/heating temperature/activation of the Clima Amico system [ 3 ] Domestic hot water temperature selector/preheating activation [ 4 ] Hydrometer Characteristics: Class A+ system without the addition of options Specific for use in built-in BOX Low consumption modulating circulator (6 m head) Low polluting emissions: class 5 (UNI EN 483) New condensing exchanger in aluminum with high flow rate and front access Thermoregulation with standard external probe REC 08 remote control panel as standard Antifreeze kit available up to -10°C (optional) Possibility of intubating flues with the special flue ø 60 in PP and ø 50 in PP IPX5D electrical protection degree Plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview CHAFFOTEAUX URBIA GREEN Ebus2 25 EU CONDENSING BOILER Cod. 3310407, COMPLETE WITH FUME EXHAUST KIT - NEW ErP: Wall-mounted condensing boilers with 4 liter mini-accumulator. Technical specifications Product code: 3310407 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Rated heat output max/min (Hi) Qn:ÿ22/2,5ÿkW Useful heating power80§ C/ 60§ C max/minÿ21,5/2,4ÿkW Useful heating power50§ C/ 30§ C max/minÿ23,4/2,6ÿkW Sanitary nominal thermal power max/min (60/80§C) PCI:ÿ25/ 5.5 kW Efficiency at nominal heat input:ÿ97.8% Efficiency 30% of nominal heat input:ÿ109.1% Energy efficiency stars: (dir 92/42/EEC) **** Capacity of the expansion vessel: 8 lt Maximum system water capacity: 100/300 litres Sanitary comfort stars(EN13203): *** Port. specific in healthcare (10 min. with T= 30øC): 13.2 l/min Hot water flow rate at T 25§ C: 14.6 l/min Degrees of protection for the electrical system:ÿIPX5D Nox class: 5 Dimensions hxwxd: mmÿ745 x 440 x 375ÿ; 42kg METHANE power supply Features list URBIA GREEN Ebus2 EU Urbia Green is the ideal solution for all homes where the best performance is required. It is a concentration of advantages in terms of sanitary comfort with reduced dimensions and consumption. Thanks to condensing technology and integration with solar systems, it maximizes energy savings and the 4-litre sanitary reserve satisfies the needs of the most demanding users. Sanitary comforts Mini-accumulintegrated in 316L stainless steel of 4 liters. Domestic hot water performance ***, maximum level not foreseen by the EN 13203 standard. Flow rate from 14.6 to 19.3 l/min with T = 25§C. DHW production controlled by a modulating turbine to respond to needs without waiting times and at a constant temperature, even when extractions are very low. DHW programmer to control the tank heating time slots Eco-Delta System: DHW load system with 4 liter reserve to further improve the comfort of DHW production and new ecological functions which allow you to save energy in DHW mode. Heating comfort Efficiencyfinal 108% with energy savingsfinal 35%. 4-star combustion efficiency according to the EN 92/42 standard. SRA function, automatic boiler regulation system according to heating requirements. Modulation wide range, from 10% to 100% of the maximum power. Reduced polluting emissions, NOx class 5. Pressure sensor of the heating circuit with visualization on LCD display. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the room and/or outside temperature. Arrangement for integration into a heating system via the newÿEbus2 communication protocolÿ(boilers, solar, system management modules, modulating thermoregulation accessories). Multifunction LCD display with display: history, self-diagnosis, operating temperature. Filling taps integrated in the boiler. Convenience of installation use Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier start-up: automatic purge function and directly accessible combustion adjustment. Save energy and respect the environment Final 25% energy savings in combination with Expert Control and the SRA function. Final 35% energy savings combine and Expert Control, the SRA function, the external probe and the radiant floor. 40% reduction in CO2 emissions**. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview BIASI INOVIA COND E 25S METHANE CONDENSING BOILER - NEW ErP, SEALED CHAMBER COMPLETE WITH FUME EXHAUST KIT: Wall mounted condensing boilers. The premixed range is simple on the outside and technological on the inside. The sites displaying the Biasi web sales authorized brand have been authorized by BSG Caldaie a Gas SpA for the sale of Biasi products. These companies therefore release the conventional guarantee. Technical specifications o Model: Inovia Cond E 25S Energy label specifications according to the European ErP directive o Class A heating energy efficiency o Sanitary energy efficiency Class A o Withdrawal profile: XL Characteristics of heating/DHW operation: o DHW useful thermal power: 24.4 kW o Useful thermal power for heating: 19.5 kW o Nominal kW heat input(*): 25 kW o Efficiency at 100% load: 106.2% o Sanitary flow rate t =25°K: 15.9 l/min o High yields (in compliance with yield directive 92/42 CEE and Legislative Decree 311/06) o Sanitary comfort (EN 13203) o Total premix burner, built in stainless steel (Class NOx 5) o Sanitary plate heat exchanger in stainless steel o High efficiency pump with low energy consumption o IPX5D degree of protection o Dimensions hxwxd: mm 700 x 400 x 290; 32kg o METHANE power supply Main features Inovia Cond E Premixed condensing boilers Inovia Cond E represents the new premixed BIASI condensing boiler. Inovia Cond E is equipped with innovative aesthetics and a new interface that is immediate and easy to use, it is equipped with new functions that make it an integral part of a system and which facilitate its installation and maintenance. Inovia Cond E offers all the advantages of condensing technology: great performance, high efficiency, energy saving and respect for the environment thanks to reduced polluting emissions such as NOx and CO. Installed in low temperature systems, they allow savings of up to 30%. Characteristics: o • High yields (in compliance with yield directive 92/42 EEC and Legislative Decree 311/06) or • Sanitary comfort (EN 13203) o • Primary condensing exchanger in stainless steel with plastic coating to offer maximum resistance to corrosion o • Total premix burner, built in stainless steel (Class NOx 5) or • Sanitary plate heat exchanger in stainless steel or • High efficiency pump with low energy consumption or • IPX5D degree of protection or • Can be installed in a partially protected place or • Integration with BIASI solar systems, using a solar kit o • Innovative digital control panel with graphic interface and keys or • Digital pressure reading by pressure transducer or • Arrangement for remote control and external probe or • Possibility of remotely managing a zone valve in the case of multi-zone systems. Control panel: o Summer/winter/off selector o Heating temperature regulator o DHW temperature regulator o Digital pressure reading o Domestic hot water and heating temperature visualization from the display o Visualization of fault diagnostics, block status and fault history o Recommended filling view and filling guide o View months left until annual maintenance is due o External temperature display (with external probe connected) and signaling of external probe connected and K value set o Display of flame modulation o Visualization of the BIASI SOLCONTROL solar control unit connected to Inovia Cond E, active solar pump and solar integration o DHW comfort function selectable by means of a dedicated and programmable key o Direct access to the INFO menu dedicated to the user. Fiscal detraction As a condensing boiler, Inovia Cond E allows you to take advantage of the tax deduction according to current legislation. d Thermoregulation By connecting the external probe (optional) directly to the boiler, climatic regulation can be used. Inovia Cond E will adapt the system water temperature to the external climatic conditions, ensuring that the desired room temperature is reached without waste and optimizing consumption. The boiler is equipped with a complete set of curves which can be accessed by entering programming. The curve is simply chosen from the control panel. Solar management Inovia Cond E integrates solar management directly into the product. Thanks to the integrated solar management it is possible to connect the SOLCONTROL control unit and view the status of the pump and the relative solar integration. Zone management Inovia Cond E features the zone management card as standard which allows you to manage a zone valve using the BIASI remote control. In the case of a system with several high temperature zones, one zone can be managed by remote control and the other zones can be managed by chronothermostats. This allows you to select two thermoregulation curves, one in the boiler and the other in the remote control. All the zones controlled by chronothermostats will be managed by the thermoregulation curve set in the boiler, the zone controlled by the remote control will be managed by the thermoregulation curve set therein. In the case of multi-zone systems at high and low temperatures, it is recommended to use the BIASI MULTIzone system manager. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the Eco-Design Directive (ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: or generators with a capacity of less than 400 kW or water heaters with a capacity of less than 400 kW, or kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows them to compare the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: o product energy label; o product data sheet; o system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; o technical data sheet of the system with the parts relating to the product or the system already completed. o Dealer liability First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: o all appliances and/or systems are equipped with the respective labels and make sure that they are clearly visible; o all devices and/or systems are always accompanied by the mandatory technical data sheets; o any type of advertising, promotional or technical material in which energy data or price indications are shown, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

FERROLI BLUEHELIX K 50 25 Kw CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Characteristics: Seasonal space heating energy efficiency class A Water heating energy efficiency class A Declared load profile XL Heat Capacity (PCI) Min / Max Heating: 5.8 / 25.0 Thermal power 80°C-60°C: 5.7 / 24.5 Useful thermal efficiency 80°C-60°C Pmax % / Pmin %: 98.0 / 97.8 Emission class Nox class 5 Boiler capacity 50 litres Domestic hot water production Δt 30°C l/10 min 175 Sanitary Manufacturing (EN 13203) ★★★ Heating working pressure Max bar 3 DHW working pressure Max bar 9 Empty weight kg 50 Dimensions HxWxD: 800 x 600 x 420 Power supply: METHANE Certified operation also with LPG using a special kit to be requested from the Authorized Assistance Centre CHARACTERISTICS Boiler body with the new patented primary exchanger in thick AISI 316 TI stainless steel Production of domestic hot water with 50-litre stainless steel domestic hot water storage tank Total premix burner in stainless steel Electronic flame modulation both in heating and DHW Digital control panel Can be combined with the modulating remote timer control Low consumption modulating heating pump (Erp Ready - Class A) Refined design and compact size Casing painted in white by anaphoresis with epoxy powders 3-star certified comfort in sanitary manufacturing according to EN 13203 Sliding temperature operation via optional external probe Digital flame control with three re-ignition attempts in case of operation due to lack of flame detection (methane model) Arrangement for recirculation attachments Standard by-pass Place of installation: also for outdoors in a partially protected place up to - 5 ° C as standard TANGIBLE FACTS max consumption standard non-modulating circulator: 0.085 kW max consumption new high efficiency circulator: 0.04 kW Degree days 2500 (average climate zone E) Energy cost: €0.19/kWh * Hypothetical annual expenditure at max standard circulator speed: €40.375 Hypothetical annual expenditure at max speed of high efficiency circulator: €11.4 Therefore, with the replacement of standard boilers with Bluehelix K 50, in line with the new ERP regulations, electricity savings of around 30% can be estimated. In reality, the savings will be even greater, since these are modulating circulators, which at minimum power can reach consumption of up to just 3 W. The low-consumption circulator installed in the Bluehelix K 50 has a variable flow rate, with ΔT control. The advantages o ered are many, including: System start-up from cold: faster start-up with full control of the thermal load on the components Long-lasting maintenance of the temperature equilibrium conditions, once the set point has been reached Better operation in limit conditions (e.g. at minimum power), reduction of on-oFF states Reactivity to variations in the thermal load, an appreciable quality in multi-zone systems ..ROBUST Others are the merits attributable to the circulator chosen for Bluehelix K 50: The PWM signal (pulse width modulation) to the circulator allows extremely rapid intervention times to complete an advanced and complete electronic platform. This results in a drastic reduction of the ON-OFF events of the burner and the circulator. Electronic control of the drive torque at start up with consequent reduction of the risk of blocking. The routine anti-seize cycle is in any case carried out every 24 hours of inactivity. Self-protection function in case of overheating Less noise All this translates into greater longevity not only of the circulator, but also of the components subject to wear and tear from frequent on-off cycles. COMFORT AND SAFETY The designers have thought of a series of functions capable of guaranteeing the quality of the domestic water, the best delivery of power to the heating system combined with a longer life for the appliance. SLIDING TEMPERATURE OPERATION With the installation of the “external probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. ANTI-LEGIONELLA FUNCTION In order to keep the storage cylinder in suitable hygienic-sanitary conditions, the product electronics are able to keep it at a temperature of 65°C at programmable time intervals from one to seven days. ANTI-BLOCK FUNCTION In order to avoid blockage and consequent damage to the heating circulator and the three-way diverter valve, after a set period of inactivity, the boiler electronics activate operation for a few seconds. ANTIFREEZE FUNCTION In the event that the temperature in the boiler drops to 5°C, the burner automatically turns on and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. ECONOMY/COMFORT FUNCTION By activating the appropriate key, heating/temperature maintenance can be excluded by the user (Economy). This makes it possible to reduce fuel consumption during periods of non-use of domestic water Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less