Technical features Product code: 3301113 Energy class in heating: A; Energy class in sanitary: A; Profile: XL; Forced draft sealed chamber; Dimensions (HxWxD) 745x400x315 mm; Weight: 32.7kg; Energy data: Nominal heat flow in heating (max/min): 22.0/2.5 kw; Nominal heat input in DHW (max/min): 26.0/2.5 kw; Thermal power (max/min) from 80° C- 60° C: 21,5/2,3 kw; Thermal power (max/min) from 50° C- 30° C: 23.6/2.6 kW; DHW thermal power (max/min): 24.9/2.4 kW Combustion efficiency (flue gas) 97.4% Efficiency at nominal heat input from 60/80° C: 97.7% Efficiency at nominal heat input from 30/50° C: 107.4% Performance Stars: 4**** Expansion tank pressure: 1 bar; Max pressure: 3 bar; Expansion tank capacity 8 l; High temperature range (min.max): 35/82 °C; Low temperature range (min/max): 20/45 °C; Exercise performance in healthcare: Min/max domestic hot water temperature: 36/60 °C Specific flow rate (10 min. with ?T=30°C): 12.8 litres/min; Quantity of hot water ?T=25°C: 15.4 litres/min; Quantity of hot water ?T=35°C: 11.0 litres/min; Comfort performance stars (EN13203) ??? Supply voltage/frequency V/Hz 230 / 50 Minimum ambient temperature of use: >0°C; Absorption: 80W; Electrical protection: IP X5D; Drain: 80, 60, 50 mm; Power supply: LPG/METHANE (G20, NG); General characteristics New generation Ariston condensing boiler, it is the perfect mix of innovation and maximum comfort at your fingertips, in fact by connecting the appliance (also thanks to the Cube S NET, the room thermostat with integrated connectivity) to your smartphone or tablet via the appropriate downloadable app for both IOS or Android, the efficiency of the boiler connected to your smartphone give the maximum desired comfort. Installation in partially protected places or with suitable boiler covers is recommended due to the need for outdoor installation to better protect the appliance. Equipped with a large Dsplay with backlit touch interface to view correct operation and regulation or in the event of boiler malfunction for rapid intervention by authorized personnel. To always have domestic hot water ready, the Genus One Net boiler works with a high-efficiency circulator with continuous modulation (ratio 1:10) so as to respond quickly to the user's needs. Finally, the boiler is extremely silent, guaranteeing minimum acoustic disturbance, guaranteeing fewer cycles on and off the boiler and a new silencer and sound-absorbing panels that allow minimum noise. Advantages: Prepared for integration into system configuration Through the new Bus Bridgenet® communication protocol; Arrangement for multi-zone and multi-temperature thermoregulation; Arrangement for solar system management; Functions: Car and comfort function; Isothermal primary heat exchanger in stainless steel; Increased DHW exchanger; Ignition system; electronic combustion control; Gas transformation from the technical menu; Cold water inlet and heating return filters;

Read more less

General characteristics Energy label specifications according to the European ErP directive   Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 31/7.0 Nominal heat input in DHW max/min kW 34.5/7.0 Max/min heating thermal power (80°C-60°C) kW 30.3/6.7 Efficiency at nominal heat input (60/80°C) % 97.7 Efficiency at nominal heat input (30/50°C) % 106.5 Efficiency at 30% at 30°C % 108.7 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Specific flow rate in DHW (10 min. with ∆T=30°C) litres/min 22.1 Quantity of hot water ∆T=25°C litres/min 19.3 Quantity of hot water ∆T=35°C litres/min 13.8 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 120 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 900/600/460 METHANE power supply Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water.   Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies...  Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers.  EVO: energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the Energy Certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston satisfies all the indications envisaged for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energy.   Class B Premium Evo Clas B Premium EVO , with integrated 40-litre double stratification storage tank, has been designed for intelligent management of domestic water. The new Clas B Premium EVO boilers, equipped with the new ABC System storage system, rationalize energy consumption and ensure cost savings on bills. The new system, a great technological intuition by Ariston, makes it possible to immediately obtain large quantities of hot water without waiting for the water in the boilers to heat up completely, thus avoiding useless waste of energy. Clas B Premium EVO is available in the heating and domestic hot water production version in 2 powers: 24 and 35 kW (sealed chamber).   Characteristics: Backlit multifunction LCD screen Continuous modulation high-efficiency circulator for optimizing consumption and maximizing performance. Modulation ratio 1:4 Acoustic comfort guaranteed thanks to the dedicated silencer Stratified boilers in duplex stainless steel Arrangement for integration with system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort Isothermal primary heat exchanger in stainless steel Oversized DHW exchanger and 2-litre DHW expansion vessel Heating expansion vessel 10 lt Cold water inlet and heating return filters   Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology   Ecodesign directive: from 2015 only new condensing boilers    After very long negotiations , the Ecodesign regulation was approved which introduces a new energy labeling on the minimum efficiency standards for boilers. In particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for domestic hot water production appliances. Hence the obligation to install only condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimney as occurs in traditional boilers. The recovered heat is transferred to the heating system, allowing to reach an efficiency of 106% against 92% of the traditional boiler and 84/85% of an old traditional generator. The installation obligation concerns boiler manufacturers who will no longer be able to place non-condensing ones on the market starting from 26 September 2015 . This means that starting from this date, anyone wishing to install a boiler in their own home will only have to install condensing models. Only a particular type of non-condensing boiler will continue to be produced which is technically called "open chamber" to be installed when it is not possible to replace an old boiler with a condensing boiler due to problems related to the collective flue of some multi-family buildings . What is Energy Labeling?       Products for heating water and the environment represent around 30% of internal energy consumption in Europe. Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations such as Italy were deactivated. As of 26 September 2015, ErP regulation and energy labeling will be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and water storage tanks hot)¹.   How to read energy labels    There are different labels, based on the type and functions of the product (water heating or space heating only or both, and in this case the label must show both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

General characteristics Energy label specifications according to the European ErP directive   Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 28/3.0 Max/min heating thermal power (80°C-60°C) kW 27.1/2.9 Efficiency at nominal heat input (60/80°C) % 97.7 Efficiency at nominal heat input (30/50°C) % 106.2 Efficiency at 30% at 30°C % 108.8 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Specific flow rate in DHW (10 min. with ∆T=30°C) litres/min 14.1 Quantity of hot water ∆T=25°C litres/min 16.8 Quantity of hot water ∆T=35°C litres/min 12 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 81 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 770/400/385 CNG or LPG power supply Kit for conversion from methane to propane supplied Ariston condensing boilers   1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water.   Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies...  Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers.  EVO: energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the Energy Certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston satisfies all the indications envisaged for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energy.   Genus Premium Evo The Genus Premium Evo wall-mounted boiler is the maximum expression of the Ariston range. Thanks to the condensing technology, by recovering the energy of the exhaust fumes, it generates an increase in the calorific value which makes it possible to eliminate waste (of energy) and to obtain higher thermal efficiency than conventional boilers. Genus Premium Evo offers even greater performance thanks to the innovative technology that allows it to self-regulate according to variations in the external and internal temperature of the room, allowing energy savings of up to 35% compared to an older generation boiler. It is available in the heating and domestic hot water production version in 3 powers: 24-30-35 kW (sealed chamber).   Characteristics: Can be installed in partially protected places Large backlit dot matrix screen Continuous modulation high-efficiency circulator: for optimizing consumption and maximizing performance. Modulation ratio 1:10 - Automatic power regulation according to the heating request. Acoustic comfort guaranteed by the lower number of boiler on and off cycles, new silencer and sound-absorbing panels Prepared for integration in system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort Isothermal primary heat exchanger in stainless steel Increased sanitary exchanger Cold water inlet and heating return filters  Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons  Acoustic comfort Acoustic comfort is further guaranteed by the introduction of the new silencer. For the Clas Premium Evo thanks also to the high modulation ratio of 1:10, the continuously modulating pump and the presence of side sound-absorbing panels.  High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology   Ecodesign directive: from 2015 only new condensing boilers    After very long negotiations , the Ecodesign regulation was approved which introduces a new energy labeling on the minimum efficiency standards for boilers. In particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for domestic hot water production appliances. Hence the obligation to install only condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimney as occurs in traditional boilers. The recovered heat is transferred to the heating system, allowing to reach an efficiency of 106% against 92% of the traditional boiler and 84/85% of an old traditional generator. The installation obligation concerns boiler manufacturers who will no longer be able to place non-condensing ones on the market starting from 26 September 2015 . This means that starting from this date, anyone wishing to install a boiler in their own home will only have to install condensing models. Only a particular type of non-condensing boiler will continue to be produced which is technically called "open chamber" to be installed when it is not possible to replace an old boiler with a condensing boiler due to problems related to the collective flue of some multi-family buildings . What is Energy Labeling?       Products for heating water and the environment represent around 30% of internal energy consumption in Europe. Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations such as Italy were deactivated. As of 26 September 2015, ErP regulation and energy labeling will be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and water storage tanks hot)¹.   How to read energy labels    There are different labels, based on the type and functions of the product (water heating or space heating only or both, and in this case the label must show both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Attention ! in case of unavailability we will supply the new model START 25 KIS General characteristics Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Heating rated heat output: 19.5 kW Sanitary nominal heat input: 25 kW Sanitary nominal thermal power: 25 kW Energy efficiency (92/42/EEC) **** Useful efficiency Pn (50°/30°): 104.2% Profit return 30% (47th return): 108.9% Sealed chamber, forced draught Quantity of hot water with Δt 25°C: 14.3 l/min Dimensions (hxwxd) mm 792 x 405 x 248 ; 30 Kgs Electrical protection degree: IP X5D NOx class: 5 Power supply: METHANE Technical features START CONDENS Yield **** Low polluting emissions Aluminum condenser, with premix burner Combined models for indoor, outdoor, built-in, with stainless steel storage tank Start Condens is the new Riello condensing wall-mounted proposal for small and medium-sized domestic users. The new compact aluminum condensing exchanger guarantees efficiency and reduction of polluting emissions. It can also be installed outdoors in a partially protected place. It is available in version 25 (with 25 kW of DHW power and 20 kW in heating) and 29 (with 29 kW of DHW power and 25 kW in heating). Characteristics: Low consumption circulator (IEE≤0.20) "Winter with Pre-heating" function: allows the DHW exchanger to be kept at temperature, reducing waiting times during withdrawal (can be activated by the user) Standard thermoregulation on the card in combination with the external probe (optional) Assembly template, hydraulic fittings, power supply cable supplied Natural gas operation as standard with the possibility of conversion to LPG (G31) and propane air (accessories), this modification is the responsibility of the installer or the technical assistance service. Possibility of outdoor installation in partially protected places, using special accessory kits. Yield **** Low polluting emissions Aluminum condenser, with premix burner Combined models and heating only for indoors, outdoors in partially protected places ErP: Energy related Products The new European regulations for heat generators ErP is the acronym of “ Energy related Products ” (products connected to the use of energy) and is the abbreviation that identifies the European Directive ErP 2009/125/EC, defined by the EEC with the intention of reducing the energy consumption of products through eco-compatible design ("eco-design "). The field of action of this European Directive is extremely broad as up to now it has involved products such as light bulbs, air conditioners, washing machines, fans, etc. Following the publication in September 2013 of a series of implementing regulations, starting from 26 September 2015 it will also apply to heating products and the production of domestic hot water. From the same date, other regulations will also become effective which will implement the energy labeling of the same product families. The transitional period between the publication of the regulations and their activation throughout the territory of the European Community was necessary to allow the full implementation of the contents by companies and market players. The energy labeling of products for heating and domestic hot water production The regulations issued require that all products intended for heating and/or for the production of domestic hot water, with a nominal thermal power lower than or equal to 70 kW, are placed on the market with an energy label that highlights their efficiency class. Note: the regulation provides for the mandatory presence of the energy label for the release of the product from the factories to the market. All products previously introduced, for example present in distribution warehouses, can be regularly marketed even if they do not have an energy label. Various energy labels have been provided based on the use of the generator used: for heating from A++ to G; for the production of domestic hot water from A to G.   A new way to guide the consumer The purpose of energy labels is to allow the consumer to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pump products, as has been done for air conditioners, the efficiency figure is reported for the average climatic range. In addition to the product energy labels, the European regulations have also provided for the creation of a system label in the event that a plant is created in which various appliances, components and controls operate. This labelling, thanks to the combinations of the data of the various elements used in the plant, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual generators. The European regulation states that the system label must be made available by whoever supplies and/or puts the system into operation (sellers-installers); however, this option is also granted to builders. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ARISTON GENUS PREMIUM NET 35 EU SMART Wi-Fi CONDENSING BOILER COMPLETE WITH METHANE FUME KIT - NEW ErP Product code: 3300906 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 31/3.5 Max/min heating thermal power (80°C-60°C) kW 30.1/3.4 Efficiency at nominal heat input (60/80°C) % 97.7 Efficiency at nominal heat input (30/50°C) % 106.5 Efficiency at 30% at 30°C % 108.7 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Specific flow rate in sanitary mode (10 min. with ∆T=30°C) litres/min 16.0 Quantity of hot water ∆T=25°C litres/min 19.3 Quantity of hot water ∆T=35°C litres/min 13.8 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 77 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 770/400/385 Genus Premium NET The top-of-the-range condensing boiler, complete with connectivity service. The Genus Premium NET wall-mounted boiler, in addition to being the maximum expression of the Ariston range, is already ready for use of the connectivity service. Thanks to the condensing technology, by recovering the energy of the exhaust fumes, it generates an increase in the calorific value which makes it possible to eliminate waste (of energy) and to obtain higher thermal efficiency than conventional boilers. Genus Premium Evo offers even greater performance thanks to the innovative technology that allows it to self-regulate according to variations in the external and internal temperature of the room, allowing energy savings of up to 35% compared to an older generation boiler. It is available in the heating and domestic hot water production version in 2 powers: 24-35 kW. Characteristics: Can be installed in partially protected places Large backlit dot matrix screen Continuous modulation high efficiency circulator Modulation ratio 1:10 Acoustic comfort guaranteed by the lower number of boiler on and off cycles, new silencer and sound-absorbing panels Prepared for integration in system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort Isothermal primary heat exchanger in stainless steel Increased sanitary exchanger Cold water inlet and heating return filters 60mm split exhaust + COMFORT: The system manager constantly monitors the room temperature even if you are away from home. No more surprises when you return! + SAVINGS: It is possible to synchronize the temperature in your home with the rhythms of your life, avoiding useless ignitions of the boiler. Lower consumption in the bill, less stress for your system! + RELIABILITY: Your trusted TAC will assist you constantly by monitoring the performance and correct functioning of your system. Serenity will always be by your side THREE SIMPLE STEPS TO GET THE MAXIMUM BENEFITS FROM THE INNOVATIVE PACKAGE 1. RECEIVE THE BOILER COMPLETE WITH THE CONNECTIVITY KIT DIRECTLY AT HOME 2. DOWNLOAD THE FREE APP TO MANAGE THE SYSTEM EVEN AWAY FROM HOME 3. CHOOSE THE TRUSTED CAT FOR CONSTANT ASSISTANCE AND TO ENSURE OPTIMAL PERFORMANCE AT ALL TIMES* Comfort and savings within reach of your smartphone, one more reason to switch to AristonNet! Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. EVO: energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the energy certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston satisfies all the indications envisaged for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energy. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Vaillant ecoTEC Exclusive VM 296/7-5+ Condensing Boiler Natural Gas Heating Only with ErP Ready Fume Exhaust Kit Technical features CNG item code: 0010017088 Heating Efficiency Class: A Nominal Thermal Power (80/60°C): 29.7 kW Nominal Thermal Power (60/40°C): 30.6 kW Nominal Thermal Power (50/30°C): 32.0 kW Nominal Thermal Power (40/30°C): 32.1 kW Nominal Thermal Power in Sanitary: 28 kW Nominal heat capacity in sanitary water: 28.6 kW Nominal heat input in heating: 30.3 kW Nominal efficiency (80/60°C) : 98% Efficiency at 30% : 108.5% Performance Stars : **** Inlet Gas Pressure: 37 mbar Consumption at Nominal Power : 3 m 3 /h Class : NOx 5 Nominal flow rate in Heating (ΔT=20K) : 1075 l/h Inbound Adjustment Temperature: 35-75 °C Water Content in the Generator : 2,2 l Power supply (V/Hz): 230/50 Total Electric Power: 81 W Stand-By Electric Power: <2 Gas connection: 20 mm Smoke Exhaust Fitting: 60/100 mm Sound Power : 50 dB(A) Degrees of Protection : IP X4 D Dimensions and weight Boiler dimensions (HxPxL): 720x338x440 Boiler weight: 35 Kg ecoTEC Exclusive VM+ All the comfort you are looking for with maximum efficiency and reliability The ecoTEC exclusive WM + wall-mounted condensing boiler has been designed to guarantee minimum harmful emissions into the environment, guaranteeing maximum performance for domestic comfort . This model of indoor boiler allows a lower consumption of gas and electricity thanks to the high quality components mounted inside such as the high efficiency pump which allows a wide modulation range. Furthermore, the ecoTEC exclusive adjusts itself automatically to provide the best comfort by making the most of the principle of condensation. The boiler internally mounts a gateway which, in combination with the multiMATIC 700 control unit (accessory that can be ordered separately, not included in the supply, mandatory for connectivity), can be interfaced with the home router with a LAN cable or a Wi-Fi transmission dongle ( can be ordered separately); through a free app developed by Vaillant it will be possible to regulate the boiler comfortably from a smartphone . This boiler model is for the production of heating only , but if combined with a Vaillant boiler it can also supply domestic hot water. ecoTEC Exlusive is the Green iQ branded condensing boiler. The boiler reaches 94% (Etas) of energy efficiency in heating thanks to the performance of the ExtraCondens exchanger which has an additional section capable of increasing DHW production efficiency by 10%. The boiler is fitted with the VR920 device which, combined with the multiMATIC 700, allows you to connect the boiler to the home WiFi network and, using an App (iOS and Android), to control it even from outside the home. It self-adapts to any type of gas and consists of 82% recyclable material effect of the made in Germany conception. The boiler has already received the Reddot Design Award. Advantages Comfort Very low noise Hot water production up to 17 l/min Unparalleled sanitary and environmental comfort savings Energy class A+ with multiMATIC 700 Excellent energy/efficiency ratio Gas self-adaptation/regulation Up to 10% annual savings compared to normal condensation Safety Environmentally friendly: 82% recyclable boiler and components Strict controls to ensure the high quality standards of Green iQ Simplicity Built-in connectivity Free app for remote management from smartphone, tablet or PC Easy and intuitive programming Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

BUILT-IN UNIT EXCLUDED! Technical Features ErP energy efficiency class (heating and DHW): A Load profile: XL Nominal heat output 24.7 kW Nominal thermal power 24 kW Energy efficiency (92/42/EEC) **** Nominal efficiency 80/60°C % 97.7 Yield at 30% % 108.8 Heating circuit water temperature regulation °C 25-80 Sanitary water temperature regulation °C 35-60 Sanitary water production ∆T 25°C l/min 13.8 Minimum flow rate of sanitary water: 2 l/min Minimum operating temperature: -15°C Expansion vessel capacity/pre-charge l/bar: 8/0.8 NOx class (EN 483): 5 Dimensions (hxwxd) - with case: mm 1170 x 600 x 245 Dimensions (hxwxd) - boiler mm 770 x 470 x 238; 32.5 kg Power supply: LPG Luna Duo-Tec IN+ The efficiency of compact built-in comfort Baxi has always offered the ideal system solution for any type of home: for this reason the Duo-tec+ range is expanding with built-in and outdoor installation models. Luna Duo-tec IN+ is the built-in condensing boiler, specifically designed to make it suitable for replacing an old built-in generator but also for new installations. The extremely compact size of the boiler makes it suitable for installation in small/medium-sized apartments, and in general in all housing units where efficient space management is an important objective (for example in technical rooms or in the presence of containment boxes) Outdoor recessed installation Luna Duo-tec IN+ is the built-in condensing boiler, specifically designed to make it suitable for replacing an old built-in generator but also for new installations. The extremely compact size of the boiler makes it easy to install in small/medium-sized apartments, and in general in all housing units where efficient space management is an important objective (for example in technical rooms or in the presence of containment boxes). Inside the packaging there are the bracket and installation fittings for inserting the boiler into the containment box Characteristics: Wide modulation range up to 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control Automatic plant loading system Minimum operating temperature: -15°C Remote digital control panel with LCD display Predisposition for combination with the Baxi integrated solar system High efficiency circulation pump with total modulation Ultra-compact dimensions: 770x470x238 mm (boiler) STANDARD installation kit (gas tap / gas inlet / telescopic fittings) Anti-freeze function and IPX5D protection degree Digital control panel The Duo-tec+ boiler range is equipped with a digital control panel with a backlit LCD display, easy to use thanks to dedicated and independent keys to adjust the temperature of the domestic hot water and heating. The display allows you to view all the information and set the operating parameters clearly and immediately. Adaptive Gas Control The innovative automatic combustion control system GAC ( Gas Adaptive Control ) guarantees a wide modulation range of up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adapt the thermal power produced to the actual power dissipated by the building, avoiding excessive overheating/cooling of the building. Antifreeze function The boilers have been designed to allow the boiler to operate down to -15°C. Furthermore, the anti-freeze function provides for the automatic ignition of the burner, avoiding freezing phenomena. Wide modulation range 1:7 greater efficiency given by fewer on-off cycles: with a high modulation ratio, the reduction of continuous on/off cycles leads to a significant reduction in consumption (8-10%) and an equal reduction in polluting emissions adjustment of the thermal power produced to the dissipated power, thus avoiding excessive overheating/cooling of the rooms Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE PRODUCT IS MADE TO ORDER NB The boiler will be supplied with methane. For operation with LPG or propane air, contact the local authorized assistance center in advance. Technical features Model : LUNA STYLE 1.12 Code: A7754010 Heating nominal heat input: 12.4 kW Power supply: methane Specifications Energy efficiency according to the European ErP directive Heating Energy Efficiency Class: A Seasonal space heating energy efficiency ŋs: 94 % Useful efficiency at 30% thermal power. name and low temperature regime. **ŋ1: 99.4 Useful efficiency (pci) at 30% - return temperature 30°C: 110.3% Useful efficiency (pci) intermediate - average temperature 70°C: 98.4% Dimensions and weight Dimensions (hxwxd): 763x450x334 mm Net weight: 31.5kg Description Backlit color control panel, icons for parameter display, clear descriptions via large text display, adjustment knob and menu selection keys Wide modulation range 1:10 (1:6 mod. 1.12) greater efficiency and silence GAC (gas adaptive control): automatic combustion control Power set: heating power adjustment according to project data Hydraulic group in brass Connection to pressurized collective flues Natural gas boilers convertible to LPG and propane air (conversion kit not required) Antifreeze function and IPX5D degree of protection Operation with a mixture composed of up to 20% hydrogen Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Biasi c low NOx outdoor condensing boiler complete with flue gas exhaust kit - New NB: PRODUCT AVAILABLE IN 6-8 WEEKS Heating / DHW nominal heat input kW 21.0 / 26.0 Yield name 60°/80°C * % 96.6 NOx class n° 6 Minimum / maximum heating pressure bar 3.0 / 0.3 Expansion tank capacity (total / useful) l 7.0 / 3.5 Maximum flow rate (ΔT=25 K) / (ΔT=35 K) l/min 14.4 / 10.3 Voltage / Power at nominal heat input V~/ W 230/99 Degree of protection n° IPX5D Height x Width x Depth mm 946x509x287; 30.7 kW Performance Stars **** ARTICA PLUS Artica Plus is the new BIASI range of wall-mounted condensing boilers for outdoor use : excellent performance thanks to the new heat exchanger and ease of use thanks to the digital control panel with display. In the version for heating and domestic hot water production Artica Plus is available in two powers, 20 and 30 kW, in the same extremely compact dimensions (946 x 509 x 287 mm). Artica Plus has its strong point in the innovative heat exchanger designed to provide high yields that last over time. Digital control panel, designed to communicate with the user easily and conveniently thanks to the remote control plus supplied as standard. Like the entire BIASI condensing range, Artica Plus allows you to obtain maximum savings from climatic thermoregulation, based on the system in which the boiler is installed. Main features High yields (★★★★ compliant with yield directive 92/42 EEC and Legislative Decree 311/06) Sanitary comfort (★★★ EN 13203) Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion Total premix burner, built in stainless steel (Class NOx 6) Modulation 1:5 CNG and also LPG Sanitary plate heat exchanger in stainless steel 7 l expansion tank for mod. 25S and 10 l for mod. 35S Maximum power adjustable according to the system High efficiency pump with low energy consumption Degree of protection IPX5D Can be installed in a partially protected place Closing the covers by means of magnets makes system loading operations and access to the gas cock immediate Digital control panel with backlit display Analog reading of the pressure on the machine, digital on the remote Automatic filling via remote Remote control plus as standard Standard external probe. High circulation single coil primary heat exchanger Biasi introduces on the market the new stainless steel heat exchanger for condensing boilers: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single strip of stainless steel to produce the coil, including inlet/outlet fittings, the following benefits are achieved: Accumulation of dirt and debris is avoided The water flow is uniformly distributed and guarantees a homogeneous heat exchange The water flow is constant for a longer life of the product Reduction of pressure drops with optimized circuit. The ease of cleaning and the robustness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display and fill guide View annual maintenance expiry The display operates according to the modes: 1. INFO. Info mode displays the following information: - External temperature (in case of external probe connected) - K value (in case of external probe connected) - Sanitary / heating temperatures chosen by the user - Smoke temperatures 2. PROGRAMMING. The programming mode allows you to change the boiler parameters. - In chimney sweep mode it is possible to test the boiler and adjust the gas valve. Thermoregulation By connecting the external probe (standard) and the remote control plus (standard) directly to the boiler, climatic regulation can be used. Artica Plus will adapt the system water temperature to the external climatic conditions, ensuring that the desired room temperature is reached without waste and optimizing consumption. By using the climatic regulation, the regulation efficiency is also raised, giving greater value to your home. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical Features Model : Full Condens EKOMB 22 Nominal Thermal Power: 22 kW Power supply: Methane Heating Seasonal efficiency: 93% Energy efficiency class: A Rated power : 5.4 ~ 17.8 kW Maximum power consumption: 80 W Domestic Hot Water Efficiency in ACS production: 84% Energy efficiency class: A (XL) Nominal heat input: 5.6 ~ 22.1 kW Seasonal efficiency: 89.2% Continuous service withdrawal (ΔT = 30°C): 10 l/min Continuous service withdrawal (ΔT = 25°C): 12 l/min Minimum withdrawal: 1.5 l/min Maximum power consumption: 55 W Electrical Data Emission class: NOx 5 Power absorbed by the circulator: 25 W Minimum power consumption: 2 W Dimensions and Weight Dimensions (LxHxD): 770x517x590 mm Weight: 30 Kg Simply Peace of Mind Guarantee To guarantee you maximum peace of mind, DAIKIN has designed “SEMPLICEMENTE SERENI”, an extension of the warranty up to the 5th year of your product's life, which includes the subscription to a Scheduled Maintenance Plan with specialized Daikin technicians. Daikin Full Condens Boiler Condensing boiler gas double condensing for heating and domestic hot water Why choose a condensing boiler? Daikin condensing boilers are a good solution for those who want to replace an existing boiler with a more efficient alternative, saving on costs. Our portfolio includes boilers for every need, from the wall-mounted D2C and Full condens and Full Condens TOP boilers, to the boiler with built-in GCU heat storage tank, to the floor-standing A2 diesel boiler. The new condensing boilers offer the advantages of condensation not only in heating but also in the production of domestic hot water. The heart of the condensing boilers is the innovative double-circuit aluminum exchanger: the mains water is heated directly in the boiler body, causing the combustion fumes to condense. Domestic hot water is produced with up to 20% greater efficiency than traditional condensing boilers. The higher the efficiency, the lower the consumption and the higher the savings! Comfort Daikin condensing boilers offer maximum comfort. They work optimally and reliably continuously, all year round, even in extreme weather conditions. For the production of domestic hot water, there are both Combi models, for instantaneous production, and models for combination with domestic hot water tanks or Daikin Sanicube thermal buffer tanks. A solution for every need! Energy efficiency Condensing technology This is a technology that exploits the latent heat present in the combustion gas and allows for high efficiencies to be achieved. The Benefits of the Simply Peace of Mind Guarantee Labor at no additional cost Free original spare parts Daikin Repair Warranty no extra costs for requests for intervention in the event of a fault under warranty The advantages of condensation in heating and domestic hot water production › Minimum operating costs thanks to the double circuit exchanger for condensation even in the production of domestic hot water › Easy, quick and space-saving installation thanks to the optional pre-assembled B-pack unit, containing all the auxiliary components Ease of installation and maintenance All components are accessible from the front and maintenance is reduced thanks to the adaptive gas combustion system Lambda Gx, a fully electronic gas-air combination. The Lambda Gx system is compatible with wall and floor units. Minimal maintenance Thanks to the innovative double-circuit aluminum exchanger, neither the plate exchanger nor the 3-way valve used by traditional condensing boilers are required for the production of domestic hot water. A smaller number of components translates into greater reliability and less and faster maintenance. Simplicity is its strength! Furthermore, having its own completely independent separate circuit, the production of domestic hot water is not interrupted in the event of failures in the heating circuit Simple, reliable and efficient Copper pipe dedicated to domestic hot water service Copper pipe dedicated to heating service Air-fume heat exchanger in aluminum in which copper pipes are drowned Condensation during ACS service point efficiency up to 101.7% and 20% more efficient than a traditional condensing boiler on an annual basis. Better performance, lower consumption and greater savings Absence of 3-way valve and plate exchanger greater reliability and less maintenance. Everything that is not there cannot break ACS service independent from the heating circuit hot water always available, even for example in the event of a water circulator breakdown Circulator active only during heating It consumes only 55W of electricity during the production of domestic hot water and extends the life of the water circulator Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

Biasi BASICA COND 25s condensing boiler complete with LPG Low NOx ErP Fume Exhaust Kit - NEW Model BASICA COND 25S DHW nominal heat input kW (kcal/h) 26.0 (22356) Nominal heat input * heating kW (kcal/h) 21.0 Maximum useful power in heating 60/80° kW (kcal/h) 20.5 (17627) Useful power in domestic hot water 60/80° kW (kcal/h) ) 25.4 (21840) Efficiency at 100% load (50/30 °C) % 106.8 Sanitary flow rate ∆t =25°K l/min 14.7 NOx class 6 GPL code10302.2043.0 Dimensions HxWxD mm 700x400x325 BASIC COND Basica Cond Basica Cond completes the BIASI range with premixed condensing: perfect for radiator systems and suitable for radiant systems with mixing groups. Basica is the compact condensing boiler that ensures high efficiency, low consumption and respect for the environment. Available for heating and domestic hot water production, in power ratings of 25 and 30 kW. Main features Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion - Total premix burner, stainless steel (Class NOx 6) - Modulation 1:5 CNG and also LPG - Sanitary plate heat exchanger in stainless steel - 8 liter expansion tank - High efficiency pump with low energy consumption - Can be installed in a partially protected place - Integration with BIASI solar systems, using a solar kit - Analog pressure reading - Arrangement for remote control and external probe High circulation single coil primary heat exchanger Biasi introduces on the market the new stainless steel heat exchanger for condensing boilers: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single strip of stainless steel to produce the coil, including inlet/outlet fittings, the following benefits are achieved: - The accumulation of dirt and debris is avoided - The water flow rate is constant, guaranteeing a higher average life of the product - Reduction of load losses with optimized circuit. The ease of cleaning and the sturdiness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. Included in delivery Boiler support bracket and paper template Boiler power cable Condensate collection siphon Quick instruction to the user. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history The display operates in the following modes : INFO – information available on the operating status and error history FREE programming – programmable parameters for generator/system adjustment and User SET INSTALLER programming - generator parameters ASSISTANCE programming - Authorized Assistance Center parameters commands The Basica Cond Range has the choice of 2 class V remote controls (they allow deduction at 65), in the Base and Top version with weekly chronothermostat functions with up to 4 programmable periods with independent temperatures, in addition to the remote control of all the information of the boiler display. Product Guarantee: All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

CHAFFOTEAUX INOA GREEN Ebus2 24 EU CONDENSING BOILER Product code: 3310477 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Nominal heat input in heating max/min (Hi): 23.5/4.5 kW Max/min DHW nominal heat input (Hi): 23.5/4.5 kW Max/min heating thermal power (80°C-60°C): 23/4.4 kW DHW max/min thermal power: 22.9/4.4 kW Efficiency at nominal heat input: 97.7% Efficiency at 30% of the nominal heat input: 106.2% Energy efficiency stars: (dir 92/42/EEC) **** Expansion vessel capacity: 8 l Sanitary comfort stars (EN13203): ** Port. specific in healthcare (10 min. with ΔT= 30°C): 10.3 l/min Hot water flow rate at ∆T 25º C: 13.9 l/min Electrical system protection degree: IPX5D Extremely compact dimensions hxwxd: mm 745x400x315 ; 24kg METHANE power supply INOA GREEN Ebus2 EU The new compact condensing boiler with aluminum alloy condensing exchanger and with all the necessary requirements to achieve the required standards in terms of energy saving. Operation only methane. Sanitary comfort Sanitary heat exchanger in stainless steel. Domestic water performance: stars **. Flow rate 13.1 litres/minute with ΔT = 25ºC. (24kW) Heating comfort Efficiency up to 108% with energy savings up to 35%. 4-star combustion efficiency in compliance with the EN92/42 standard. Modulation range from 25% to 100% of maximum power. Condensing exchanger in aluminum alloy. Reduced polluting emissions, NOx class 5. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Arrangement for integration into a heating system via Ebus 2 communication protocol (boilers, solar, system management modules and modulating thermoregulation accessories). Possibility of managing single-temperature and multi-temperature zones only via Expert Control. Self-diagnosis system by code. LCD display. Comfort of use and installation Possibility of connection with external probe. Compatible with Expert Control, modulating accessories and on/ff. Easier starting: automatic purge function and directly accessible combustion regulation. Energy saving and respect for the environment Up to 20% energy savings in combination with chronothermostat and external probe. 40% reduction in CO 2 emissions **. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months

Read more less