NB: IN CASE OF LACK OF AVAILABILITY OF THIS ITEM THE OPLALIA F 15 LOW NOX MODEL WILL BE SHIPPED !!! Model: ErP efficiency class in heating/DHW: B Sanitary load profile: XL Combustion chamber: sealed with forced draft Sanitary Min/max rated power: kW 7.5 - 24.0 Heat input to the firebox kW 28.0 Type of regulation: Modulating Ignition type: Electronic Specific flow rate (∆T=25 K): l/min 14 Minimum ignition flow l/min 2.7 Minimum supply pressure bar 0.1 Electrical characteristics Supply voltage (V/Hz): 230/50 Dimensions: Dimensions (hxwxd): 627/348/240 mm ; 19.3kg Fume outlet diameter mm 80/80-60/100 LPG code - 10013754 LPG version To view further information on the product CLICK HERE and consult the technical data OPALIA The entire range of Opalia water heaters is characterized by extreme ease of use and reliable performance combined with a modern design and simplicity of use. The Opalia model is available in the open chamber and sealed chamber versions, 11 or 14 litres, all equipped with electronic ignition with safety lockout in the event of pilot flame failure. Characteristics: Modern design and compact dimensions: the water heaters can be easily installed in any room, even inside the kitchen cupboards. Maximum safety: the safety thermostat intervenes in the event of overheating of the domestic hot water; the ionisation flame control blocks the gas supply in the event of a burner flame failure; in the open chamber models, the fume anti-reflux safety device blocks the water heater in the event of a risk of fumes being released into the environment. Electronic control (only for sealed chamber models) : it is possible to optimally adapt the operation of the appliance to the conditions of use and the temperature of the hot water, guaranteeing maximum sanitary comfort and optimizing gas consumption. Any malfunctions are signaled on the LCD display. General characteristics Opalia F 11 E - A/2 and F 14 E - A/2 Sealed chamber instantaneous gas water heaters Electronic ignition board for: - check the required hot water temperature - allow the water heater to be switched on and off - check the sequence of the burner ignition cycle - check that there is no burner flame Flame modulation in relation to the temperature detected by the probe at the exchanger outlet Water heater status display and fault diagnostics Safety thermostat which blocks the water heater in the event of overheating at the exchanger outlet Modulating gas valve Flow sensor Copper lamellar heat exchanger Smoke pressure switch Standard antifreeze system (water heater ignition at 7 °C) All ready for Energy Labeling 1. ErP, Ecodesign and ELD. What do they mean and how do they differ? ErP and Ecodesign: The EU has issued new obligations for Energy Using Products (ErP). Known as the Ecodesign Directive, it prescribes minimum efficiency requirements and emission limits for heating and DHW production appliances up to 400 kW. ELD: In addition to the ErP Directive, the EU is also introducing a mandatory energy labeling for the same type of appliances up to 70 kW. The Energy Labeling Directive (ELD) requires that new products and systems for heating and DHW production are labeled with an indication of their energy efficiency class. 2. Which products are affected by the new directives? The Ecodesign directive addresses two product categories that are relevant to our installers and resellers. Category 1: Includes electric, gas and oil space heaters, combination boilers, heat pumps and cogenerators. Category 2 : includes electric, gas and oil-fired DHW production equipment, DHW heat pumps and solar systems. By combining these products and components, for example by adding a temperature control unit, the energy classification of the system can be increased, which will be calculated by the installer and indicated on the package label. 3. When will the new rules apply and how will they affect me? At the moment a transition phase is underway which lasts until 26 September 2015, the day on which the new rules come into force. Until then, neither manufacturers, retailers or installers have to comply with the new ecodesign or labeling provisions. Once the new rules come into force, only products that meet the new eco-design requirements and have an energy label can be sold on the market. 4. What does it mean for me today? Installers could play an even more important role than before. The new directives open up new opportunities for Hermann Saunier Duval's partners on the provision of ErP support services and tools. Unlike appliances, labels on heating and DHW systems can only offer a first orientation and will not necessarily provide the best solution for your customer, nor give any indication of the assumed energy cost when achieving a high energy rating. This is why customers will need your advice to understand the label and select the best product or system that best meets their needs. Hermann Saunier Duval provides its partners with a software tool to easily download all the product labels in the price list and to easily and intuitively calculate the system labels that must necessarily be provided to the end customer during the offer or be displayed in retailers' public exhibition areas. Access the Software 5. Why push condensing technology right away? Condensing products reach efficiency levels above 100% and allow gas savings of up to 30% per year. They are therefore environmentally friendly products and friends of savings. Condensing products are safe and extremely silent, efficient and easily adjustable with control units and thermostats, even wireless ones, always guaranteeing the right temperature and maximum comfort in the rooms. For the energy requalification of individual homes, the 2007 Budget Law was extended until 31 December 2015. The request for a 65% tax deduction concerns, for example, the replacement of a traditional boiler with a condensing boiler. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Sealed Chamber Gas Water Heater Savio SAVINO HE 16S Low NOx Methane Complete with Smoke Exhaust Kit Water heater Plus 16S Nominal heat input (Hi) kW 30.0 Maximum water flow rate (increase at 25 °C) kg/min 16.0 Appliance type C 13-33 Maximum water pressure (Pw) bar 10 Minimum water pressure (Pw) bar 0.2 Power supply 230V ~ 50Hz IPX4 electrical protection degree Ignition method Automatic impulse ignition controlled directly from the water opening Destination countries IT G 1/2 gas inlet fitting G 1/2 cold water inlet fitting G 1/2 hot water outlet fitting Diameter of the flue gas exhaust pipe mm Ø 60 x Ø 100 ErP DATA XL load profile Energy efficiency of water heating system (ηWH) % 80.5 Energy efficiency of water heating system A Daily gas consumption (corrected) kWh 24.845 Daily electricity consumption (corrected) kWh 0.061 Annual electricity consumption AEC (kWh) 14 NOx mg/kWh 47 Internal sound power level (LWA) dB 63 NOx class 6 Product code 10106.1000.0/0 LPG supply Measures HxWxD 667x345x186 SAVINO Low NOx emission gas wall mounted water heater Available in 12 kW, 14 kW and 16 kW versions with very compact dimensions Energy saving This product features advanced technologies called Strengthened Combustion and Forced Combustion. These two patents make it possible to make the best use of thermal energy with high operating efficiency. Ease of use Thanks to the digital control panel with large display, the user can communicate easily and conveniently with the boiler. Digital control to automatically keep the outlet water temperature constant This function continuously checks the outlet water temperature thanks to a sensor and transfers the data to a microprocessor. The latter adjusts the quantities of gas and water supplied to automatically keep the outlet water temperature constant based on the value set by the user and the actual inlet water temperature. Digital control to automatically keep the outlet water temperature constant This function continuously checks the outlet water temperature thanks to a sensor and transfers the data to a microprocessor. The latter adjusts the quantities of gas and water supplied to automatically keep the outlet water temperature constant based on the value set by the user and the actual inlet water temperature Set the temperature with one touch To set the required temperature, simply touch the digital display. The water temperature can be set between 35°C and 65°C, allowing different needs to be satisfied with maximum ease of use. Multiple security protection This product is equipped with various safety protections, including: • Protection of the self-monitoring system • Auto power off protection, • Overheating protection • Protection from accidental interruption of electricity • Fan failure protection • Protection from electrical overload • Protection against leakage current • Protection from excessive wind pressure • Protection from excessive temperatures • Timed protection “AI” Intelligent Artificial Memory Function When restarted, the gas water heater can operate with the last previously set temperature. No need to set the temperature again - a great practical application of the ergonomics idea. Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Product name GAS WATER HEATER VAILLANT ATMOMAG 14-0/1 XI LPG. Open Room WITH NATURAL DRAFT Technical features ErP energy class: Class A Nominal heat output: 24.4 kW DHW direct withdrawal range T = 25C: 2.5 - 14 l/min Chamber Open to natural draught Ignition: electronic Compact dimensions (HxDxL): 680/270/350 mm Power supply: LPG General characteristics ATMOMAG Instantaneous water heaters with electronic battery ignition. AtmoMAG XI are natural draft water heaters with electronic ignition powered by batteries. Saving safety without the aid of electricity. The Direct Start system allows for faster ignitions. The ionization flame detection ensures operational safety. The adoption of the OPTI MOD system for flame regulation allows the water temperature to be adapted to the changing seasons with a quick gesture. In the mini version, characteristics and functionality remain unchanged and the small dimensions become the reason of choice in some living situations. atmoMAG XI (hot water production) the atmospheric version with DHW flow rate of: 14 litres/minute Methane LPG atmoMAG XI mini (hot water production) the atmospheric version with DHW flow rate of: 11 litres/minute Methane LPG Characteristics : Compact size Manual range selector Automatic flame modulation LCD display Domestic hot water Power selectable on 10 levels Ionization flame control New hydraulic unit Exchanger with Supral protection ErP and ELD: what it means and how they differ ErP: The EU has issued new obligations for Energy Using Products (ErP). The new directive, known as the Ecodesign directive, prescribes minimum efficiency requirements and emission limits for appliances that produce heating and domestic hot water. The Eco design directive addresses two relevant product categories for installers and retailers in the sector: Category 1 includes space heaters; in particular: electrical, gas and diesel appliances such as boilers, heat pumps and cogenerators. Category 2 Includes appliances for the production of domestic hot water: electric, gas, diesel such as water heaters, heat pumps for DHW, solar systems up to 400 kW and boilers up to 2000 litres. ELD: In addition to the ErP directive, the EU has also introduced a mandatory energy labeling for the same type of appliances up to 70 kW and boilers up to 500 litres. The energy labeling directive is called ELD and requires that new products and systems for heating and domestic hot water production be labeled with an indication of their energy efficiency class. By combining the products and components, for example by adding a temperature control unit, it is possible to increase the energy classification of the system which will be calculated by the installer and indicated on the package label. Product Guarantee All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Overview GAS WATER HEATER BAXI mod. ACQUAPROJET 14I METHANE, Open Room WITH NATURAL DRAFT. Technical specifications Gas instantaneous water heaters Chamber Open to natural draught Nominal heat input kW 25.8 Nominal thermal power kW 22.7 Minimum thermal power kW 7.7 Minimum heat input kW 8.8 Operating water pressure 0.2-6 bar Water withdrawal range l/min 3-13 Maximum outlet water temperature C 65 Discharge pipe diam. 132mm Dimensions hxwxd mm 585x360x220 ; kg 10.5 METHANE version Features list ACQUAPROJET: the NEW instantaneous gas water heater Baxi offers a new instantaneous gas water heater, with Open Chamber and 2 Chamber models - Sealed Chamber water heaters of 11 and 13 l/min Open Chamber Models 11- 14 l/min Battery electronic ignition Electronic detection of flame presence Gas valve with modulation proportional to the water flow rate to keep the outlet temperature stable Minimum ignition flow 2.9 l/min Battery status LED indicators LPG conversion kit available as an option Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Sealed Chamber Gas Water Heater Savio SAVINO HE 14S Low NOx Methane Complete with Smoke Exhaust Kit Water heater Plus 14S Nominal heat input (Hi) kW 28.0 Maximum water flow rate (increase at 25 °C) kg/min 14.0 Appliance type C 13-33 Maximum water pressure (Pw) bar 10 Minimum water pressure (Pw) bar 0.2 Power supply 230V ~ 50Hz IPX4 electrical protection degree Ignition method Automatic impulse ignition controlled directly from the water opening Destination countries IT G 1/2 gas inlet fitting G 1/2 cold water inlet fitting G 1/2 hot water outlet fitting Diameter of the flue gas exhaust pipe mm Ø 60 x Ø 100 ErP DATA XL load profile Energy efficiency of the water heating system (ηWH) % 84.0 Energy efficiency of water heating system A Daily gas consumption (corrected) kWh 23.583 Daily electricity consumption (corrected) kWh 0.064 Annual electricity consumption AEC (kWh) 14 NOx mg/kWh 29 Internal sound power level (LWA) dB 61 NOx class 6 Product code 10104.1009.0/0 (LPG)/ 10114.1009.0/0 (MET) SAVINO Low NOx emission gas wall mounted water heater Available in 12 kW, 14 kW and 16 kW versions with very compact dimensions Energy saving This product features advanced technologies called Strengthened Combustion and Forced Combustion. These two patents make it possible to make the best use of thermal energy with high operating efficiency. Ease of use Thanks to the digital control panel with large display, the user can communicate easily and comfortably with the boiler. Digital control to automatically keep the outlet water temperature constant This function continuously checks the outlet water temperature thanks to a sensor and transfers the data to a microprocessor. The latter adjusts the quantities of gas and water supplied to automatically keep the outlet water temperature constant based on the value set by the user and the actual inlet water temperature. Digital control to automatically keep the outlet water temperature constant This function continuously checks the outlet water temperature thanks to a sensor and transfers the data to a microprocessor. The latter adjusts the quantities of gas and water supplied to automatically keep the outlet water temperature constant based on the value set by the user and the actual inlet water temperature Set the temperature with one touch To set the required temperature, simply touch the digital display. The water temperature can be set between 35°C and 65°C, allowing different needs to be satisfied with maximum ease of use. Multiple security protection This product is equipped with various safety protections, including: • Protection of the self-monitoring system • Auto power off protection, • Overheating protection • Protection from accidental interruption of electricity • Fan failure protection • Protection from electrical overload • Protection against leakage current • Protection from excessive wind pressure • Protection from excessive temperatures • Timed protection “AI” Intelligent Artificial Memory Function When restarted, the gas water heater can operate with the last previously set temperature. No need to set the temperature again - a great practical application of the ergonomics idea. Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

OFFER - Immergas Julius Open Chamber Water Heater 14 liters Methane 3.025675LPG DHW energy class A Maximum nominal heat input kW (kcal/h) 27.3 (23,446) Maximum useful thermal power kW (kcal/h) 24.4 (20,984) Minimum nominal heat input kW (kcal/h) 11.1 (9,588) Minimum useful thermal power kW (kcal/h) 9.8 (8,428) Specific flow rate in continuous service of domestic hot water (∆t 25 °C ) in mixing l/min 14.0 Power supply 2 x LR20 1.5V batteries Dimensions HxWxD 630x350x230 mm JULIUS ECO ULTRA COMPACT DESIGN The small overall dimensions (only 23 cm deep) allow it to be installed even in vlocali with limited spaces or inside the kitchen wall units. EXCELLENT TEMPERATURE CONTROL The modulating gas valve chokes the gas flow to the burner ensuring a consumption proportional to the quantity of domestic hot water requested by the user. ELECTRONIC BATTERY IGNITION It allows the devices to be installed even in environments without an electrical network. FIREPLACE SAFETY DEVICE In the event of insufficient chimney draft, it intervenes by switching off the water heater Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Open chamber water heater Junkers Minimaxx powecontrol 14 liters WR-14 2B LPG Installation: Outdoor White color Material: Metal Length/Depth (cm): 35 Width (cm): 22 Height (cm): 65.5 Batteries Required: Yes Power (kW): 23.6 Prod hot water (l/min): 4 - 14 Combustion type: Open chamber Placement: Mural Fuel type: LPG Ideal for: Less than 150 m2 / 2 bathrooms Usage: Domestic hot water Minimaxx Maximum power in minimum space Do you need more comfort when using hot water? Is the space you have to place the water heater limited? Junkers has the solution… MINIMAXX POWERCONTROL , an ionisation water heater with compact dimensions which, thanks to the electronic-automatic ignition of the pilot flame via batteries, reduces consumption with a lower environmental impact. MINIMAXX POWERCONTROL , like all the water heaters in the Junkers range, can be integrated with thermal solar systems, with forced circulation and natural circulation. Technical features Integration with natural circulation solar thermal systems for the production of domestic hot water thanks to the new Solar Kit Possibility of satisfying all comfort needs thanks to the completeness of the range, made up of products with flow rates up to 17l/min Maximum operational safety thanks to the IPX4D electronic insulation degree Installation flexibility thanks to its small size: the 11 liter model is the smallest instantaneous gas water heater available on the market Versatility of application thanks to operation even in the presence of minimum water pressures (0.1 bar). Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: IN CASE OF LACK OF AVAILABILITY OF THIS ITEM THE OPALIA F 15 LOW NOX MODEL WILL BE SHIPPED !!! Model: ErP efficiency class in heating/DHW: B Sanitary load profile: XL Combustion chamber: sealed with forced draft Sanitary Min/max rated power: kW 7.5 - 24.0 Heat input to the firebox kW 28.0 Type of regulation: Modulating Ignition type: Electronic Specific flow rate (∆T=25 K): l/min 14 Minimum ignition flow l/min 2.7 Minimum supply pressure bar 0.1 Electrical characteristics Supply voltage (V/Hz): 230/50 Dimensions: Dimensions (hxwxd): 627/348/240 mm ; 19.3kg Fume outlet diameter mm 80/80-60/100 METHANE version To view further information on the product CLICK HERE and consult the technical data OPALIA The entire range of Opalia water heaters is characterized by extreme ease of use and reliable performance combined with a modern design and simplicity of use. The Opalia model is available in the open chamber and sealed chamber versions, 11 or 14 litres, all equipped with electronic ignition with safety lockout in the event of pilot flame failure. Characteristics: Modern design and compact dimensions: the water heaters can be easily installed in any room, even inside the kitchen cupboards. Maximum safety: the safety thermostat intervenes in the event of overheating of the domestic hot water; the ionisation flame control blocks the gas supply in the event of a burner flame failure; in the open chamber models, the fume anti-reflux safety device blocks the water heater in the event of a risk of fumes being released into the environment. Electronic control (only for sealed chamber models) : it is possible to optimally adapt the operation of the appliance to the conditions of use and the temperature of the hot water, guaranteeing maximum sanitary comfort and optimizing gas consumption. Any malfunctions are signaled on the LCD display. General characteristics Opalia F 11 E - A/2 and F 14 E - A/2 Sealed chamber instantaneous gas water heaters Electronic ignition board for: - check the required hot water temperature - allow the water heater to be switched on and off - check the sequence of the burner ignition cycle - check that there is no burner flame Flame modulation in relation to the temperature detected by the probe at the exchanger outlet Water heater status display and fault diagnostics Safety thermostat which blocks the water heater in the event of overheating at the exchanger outlet Modulating gas valve Flow sensor Copper lamellar heat exchanger Smoke pressure switch Standard antifreeze system (water heater ignition at 7 °C) All ready for Energy Labeling 1. ErP, Ecodesign and ELD. What do they mean and how do they differ? ErP and Ecodesign: The EU has issued new obligations for Energy Using Products (ErP). Known as the Ecodesign Directive, it prescribes minimum efficiency requirements and emission limits for heating and DHW production appliances up to 400 kW. ELD: In addition to the ErP Directive, the EU is also introducing a mandatory energy labeling for the same type of appliances up to 70 kW. The Energy Labeling Directive (ELD) requires that new products and systems for heating and DHW production are labeled with an indication of their energy efficiency class. 2. Which products are affected by the new directives? The Ecodesign directive addresses two product categories that are relevant to our installers and resellers. Category 1: Includes electric, gas and oil space heaters, combination boilers, heat pumps and cogenerators. Category 2 : includes electric, gas and oil-fired DHW production equipment, DHW heat pumps and solar systems. By combining these products and components, for example by adding a temperature control unit, the energy classification of the system can be increased, which will be calculated by the installer and indicated on the package label. 3. When will the new rules apply and how will they affect me? At the moment a transition phase is underway which lasts until 26 September 2015, the day on which the new rules come into force. Until then, neither manufacturers, retailers or installers have to comply with the new ecodesign or labeling provisions. Once the new rules come into force, only products that meet the new eco-design requirements and have an energy label can be sold on the market. 4. What does it mean for me today? Installers could play an even more important role than before. The new directives open up new opportunities for Hermann Saunier Duval's partners on the provision of ErP support services and tools. Unlike appliances, labels on heating and DHW systems can only offer a first orientation and will not necessarily provide the best solution for your customer, nor give any indication of the assumed energy cost when achieving a high energy rating. This is why customers will need your advice to understand the label and select the best product or system that best meets their needs. Hermann Saunier Duval provides its partners with a software tool to easily download all the product labels in the price list and to easily and intuitively calculate the system labels that must necessarily be provided to the end customer during the offer or be displayed in retailers' public exhibition areas. Access the Software 5. Why push condensing technology right away? Condensing products reach efficiency levels above 100% and allow gas savings of up to 30% per year. They are therefore environmentally friendly products and friends of savings. Condensing products are safe and extremely silent, efficient and easily adjustable with control units and thermostats, even wireless ones, always guaranteeing the right temperature and maximum comfort in the rooms. For the energy requalification of individual homes, the 2007 Budget Law was extended until 31 December 2015. The request for a 65% tax deduction concerns, for example, the replacement of a traditional boiler with a condensing boiler. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Energy label specifications according to the European ErP directive   Sanitary Energy Efficiency : Class A Load profile: L Exercise features: Open chamber with natural draft Ignition - 1.5 battery Flame control - by ionization Nominal heat output: 24 kW Hot water production Δ T=25°C: 14 l/min Min/max pressure bar 0.3/10 Ø water and gas connections - 1/2” Dimensions (HxLxP): mm 620x380x224; 11.5 kgs The guarantee is the Official Beretta Italia one, and has a duration of 24 months Power supply: LPG General characteristics SOURCE 2 DGT Fonte 2 DGT, hot water in compact dimensions From Beretta's experience and technological research comes the new line of Fonte 2 DGT water heaters, designed to offer maximum sanitary comfort, maximum energy savings and greater simplicity of use. Thanks to its extremely compact dimensions, Fonte 2 DGT can also be placed in limited spaces and therefore represents the ideal solution to meet the installation needs of modern living contexts. The range, open ionization chamber with battery ignition, two water filters as standard and with codes for both methane and LPG, is made up of the Fonte 2 DGT versions with 11 and 14 litres/min models and Fonte 2 DGT FLEX with a from 11 litres/min. The FLEX versions also include the hoses and the sanitary tap. Source 2 DGT: high energy class and low consumption The Fonte 2 DGT line of water heaters is equipped with the special device known as the Economiser, specifically designed to combine maximum user comfort with significant energy and cost savings. The activation of the Economizer in fact allows to reduce gas consumption up to over 50%, limiting the maximum thermal power supplied, when the usage requirements are contained (low temperature difference or reduced sampling flow rates, such as for example during summertime). Furthermore, on all Fonte 2 DGT models, the Economizer can be adjusted progressively by the user, according to needs, achieving maximum savings in the low flame position. Finally, the appliances in the Fonte 2 DGT range are equipped with flame modulation which, by adapting gas consumption to individual withdrawal requests, allows the temperature of the water supplied to be kept almost constant, compatibly with the settings made and the power of the water heater. The Beretta Fonte 2 DGT water heater guarantees always very low gas consumption and respect for the environment. Beretta Fonte 2 DGT complies with the current ERP regulation placing itself in CLASS A for energy consumption. Functionality and ease of use The Fonte 2 DGT water heaters, with a linear and essential design, have an ergonomic dashboard which houses two knobs which allow you to manage all the functions of the appliance in a simple and intuitive way and a display which shows the temperature of the domestic hot water produced. The left knob, in addition to the on/off functions, activates the "Gas economiser" device, adjustable between the small flame and the large flame, allowing the user to make an interesting gas saving. The right knob allows you to set the temperature of the water supplied, by regulating the quantity of water at the outlet Characteristics: Instantaneous open chamber water heater with Natural Gas and LPG versions Abundant production of domestic hot water: 11 or 14 litres/min Digital display with indication of domestic hot water temperature Battery ignition and ionisation flame presence control Gas economizer with 8 regulation steps Modulating flame regulation system Simple and intuitive control panel Compact size and simple installation without removing the shell Assembly template supplied (gasket and hose holder for LPG versions) New easy access water connections on the same horizontal axis New latest generation water/gas group with integrated gas pressure regulator Double inlet water filter Safety microswitch to protect the batteries (2 x 1.5 Volt type D) in the OFF position Temperature selector FLEX versions with flexible fittings and standard tap Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Sealed Chamber Gas Water Heater Savio SAVINO HE 12S Low NOx LPG Complete with Smoke Exhaust Kit Water heater Plus 12S Nominal heat input (Hi) kW kW 24.00 Maximum water flow rate (increase at 25 °C) kg/min 12.0 Appliance type C 13-33 Maximum water pressure (Pw) bar 10 Minimum water pressure (Pw) bar 0.2 Power supply 230V ~ 50Hz IPX4 electrical protection degree Ignition method Automatic impulse ignition controlled directly from the water opening Destination countries IT G 1/2 gas inlet fitting G 1/2 cold water inlet fitting G 1/2 hot water outlet fitting Diameter of the flue gas exhaust pipe mm Ø 60 x Ø 100 ErP DATA Load profile M Energy efficiency of water heating system (ηWH) % 78 Energy efficiency of water heating system A Daily gas consumption (corrected) kWh 7,836 Daily electricity consumption (corrected) kWh 0.044 Annual electricity consumption AEC (kWh) 140 NOx mg/kWh 47 Internal sound power level (LWA) dB 61 NOx class 6 Product code 10102.1000.0/0 LPG supply Measures HxWxD 667x345x186 SAVINO Low NOx emission gas wall mounted water heater Available in 12 kW, 14 kW and 16 kW versions with very compact dimensions Energy saving This product features advanced technologies called Strengthened Combustion and Forced Combustion. These two patents make it possible to make the best use of thermal energy with high operating efficiency. Ease of use Thanks to the digital control panel with large display, the user can communicate easily and conveniently with the boiler. Digital control to automatically keep the outlet water temperature constant This function continuously checks the outlet water temperature thanks to a sensor and transfers the data to a microprocessor. The latter adjusts the quantities of gas and water supplied to automatically keep the outlet water temperature constant based on the value set by the user and the actual inlet water temperature. Digital control to automatically keep the outlet water temperature constant This function continuously checks the outlet water temperature thanks to a sensor and transfers the data to a microprocessor. The latter adjusts the quantities of gas and water supplied to automatically keep the outlet water temperature constant based on the value set by the user and the actual inlet water temperature Set the temperature with one touch To set the required temperature, simply touch the digital display. The water temperature can be set between 35°C and 65°C, allowing different needs to be satisfied with maximum ease of use. Multiple security protection This product is equipped with various safety protections, including: • Protection of the self-monitoring system • Auto power off protection, • Overheating protection • Protection from accidental interruption of electricity • Fan failure protection • Protection from electrical overload • Protection against leakage current • Protection from excessive wind pressure • Protection from excessive temperatures • Timed protection “AI” Intelligent Artificial Memory Function When restarted, the gas water heater can operate with the last previously set temperature. No need to set the temperature again - a great practical application of the ergonomics idea. Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Gas Water Heater Watertight Chamber Biasi mod. 14S complete with smoke exhaust kit Model: 14s water heater Electronic ignition - Flame modulation Technical features: Maximum useful power kW 24 Nominal heat input kW 28 Efficiency 84 % Natural gas consumption (G20) (kcal/mc) m3/h 3.0 Propane consumption (G31) (kcal/kg) kg/h 2.1 Maximum water flow 14 l/min Minimum water flow l/min 2.7 Minimum water pressure bar (kPa) 0.5 (50) Maximum sanitary pressure bar 10 Dimensions without packaging (HxLxP) mm 627-348-240 Power supply: methane Biasi water heater Scaldacqua is the gas water heater for the instantaneous production of domestic hot water. it is available in the open chamber versions, with useful power of 19.0 kW (11 litres) and 23.7 kW (14 litres) and in the sealed chamber version, with useful power of 22.5 kW (8 litres). The compact dimensions and linear aesthetics allow for easy installation of the Water Heater inside the home. In particular, Scaldaqua 14S, being of type C, watertight, is exempt from most of the limitations deriving from the ventilation of the rooms and can also be installed in narrow rooms without volume restrictions. Sealed chamber modulation: It is equipped with an electronic board for continuous modulation of the power supplied, according to the temperature set by the user; moreover, the power of the burner depends on the amount of water required. In these modes, the appliance only consumes the quantity of gas that is strictly necessary. Control panel: ON-OFF knob: in the ON position, the display shows the adjustment temperature of the hot water set with the temperature adjustment knob and if there is water drawn from the top left, the flame symbol lights up (burner on) . Temperature adjustment knob: the hot water temperature can be adjusted between 35 and 60 °C by turning the adjustment knob. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Energy class B L sampling profile Power supply 2x 1.5 V LR 20 Mechanical ignition Nominal heat input (min-max) 10.5 - 27 [kW] Nominal thermal power (min-max) 9 - 23 [kW] Water pressure (min-max) 0.2 - 10 [bar] Minimum operating temperature 5°C Air flow required for combustion 45.4 m3/h Minimum draft 12 Pa Characteristics Over-temperature thermostat Flame detection electrode Exhaust gas overheating detector Copper exchanger for greater durability Simple temperature setting, two knobs, one for regulating the water flow, the other for the gas level Led light that signals the need to change the batteries Excellent compatibility of water and gas connections for all installation conditions Dimensions Dimensions (HxLxW): 580x370x225mm

Read more less