BERETTA CIAO AT 25 CSI CONDENSING BOILER COMPLETE WITH LPG FUME EXHAUST KIT - NEW ErP Product code: 20113788 Characteristics: Energy efficiency in heating: B Energy efficiency Sanitary: A Sanitary load profile: XL Nominal heat input: 25 kW Electric Power: 129W Supply voltage/frequency: 230/50 Volt/Hz Electrical protection degree: X5D ip Dimensions HxWxD: 780 x 400 x 338 ; 40 Kg Gas version available: METHANE Warm-up exercise: Maximum pressure and temperatures: 3/90 bar/°C Heating temperature selection range: 40/80 °C Pump: pump head available for the system: 266 m/bar Expansion tank capacity: 8 l Healthcare exercise: Maximum pressure: 6 bars Minimum pressure: 0.15 bar Quantity of hot water with ∆t=25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min DHW temperature selection range: 37 - 60 °C NB. THE BOILER WILL BE SUPPLIED WITH METHANE, THE ADJUSTMENT NECESSARY FOR LPG OPERATION WILL BE CARRIED OUT FREE OF CHARGE BY THE BERETTA ASSISTANCE CENTER DURING THE FIRST IGNITION. Beretta HELLO AT Hi AT, ideal for replacement in systems with radiators. Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving. High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger. Management: The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. The Ciao AT technology makes use of the condensing exchanger which recovers the latent heat of the fumes, the same principle used by condensing boilers. The exchanger, located at the top left, is connected directly to the fan which pushes the fumes inside it, before they are definitively expelled. The difference in the temperature of the fumes between the ~140°C inlet and the ~65°C outlet of the condensing exchanger is indicative of the amount of heat recovered from them. The return from the system first passes through the condensing exchanger which recovers the heat from the fumes, and then passes through the primary exchanger, where it receives the remaining heat in order to reach the required flow temperature. The water then recovers part of the heat from the fumes, which would otherwise be expelled into the atmosphere, thus giving rise to less waste and consequently greater savings for the user. Outdoor installation: Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required. Up to 17 meters of Ø 60 ducting with the Ciao AT boiler: With Ciao AT it is possible to comfortably duct even the most "difficult" flues thanks to the approval for Ø 60mm flue systems which is added to the traditional Ø 80 mm ducting flue system. The main 60mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. TECHNICAL FEATURES: Specific for systems with radiators and radiators (at high temperature) Condensing post exchanger in aluminum alloy Possibility of outdoor installation with antifreeze heater kit (optional) IPX5D electrical protection degree Environmental Self-Regulation System (SARA) Low consumption circulator 6 m (EEI≤0.20) Hydraulic connections cover (optional) Condensate collection neutralizer drawer kit (optional) Template, hydraulic fittings, gas and sanitary taps (optional) For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: PRODUCT DISCONTINUED --> THE NEW MODEL EXCLUSIVE GREEN E 25 WILL BE SHIPPED Beretta EXCLUSIVE GREEN HE 25 boiler Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Heating nominal heat output: 21.44 kW Classification European Directive EEC 92/42: ★ ★ ★ ★ Sanitary comfort ★ ★ ★ (EN 13203) NOx emission class: 5 (UNI EN 677) Efficiency at rated power: 98.7% Efficiency at reduced load (30%): 109.6% Total electric power: 93W Electrical protection degree: iP X5D Expansion tank capacity: 9 lt Quantity of hot water with Δt=25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min Sanitary water temperature selection range: 35 - 60°C Dimensions (hxlxp) mm 845x453x358 ; 44kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control). EXCLUSIVE GREEN HE HI-EFFICIENCY ECOLOGICAL CONDENSING WALL-MOUNTS The new Exclusive Green E condensing boilers, equipped with the innovative Beretta front exchanger, in addition to implementing the requests of the ErP standards, improve all the peculiarities confirming themselves as top of the range. Seasonal efficiency up to 94%, very wide modulation range (up to 1:10), low consumption modulating circulator with the possibility of increasing the head up to 7m and reduced consumption are some of the main features. The new Exclusive Green E boilers also offer excellent reliability and technology and, thanks to their high performance, are an excellent solution in hybrid systems with solar thermal and heat pumps. The external probe that allows you to activate the climatic thermoregulation is standard as standard. Furthermore, by adding the optional BeSMART WiFi Comfort Control kit and the LINK MODE interface board kit, Exclusive Green E constitutes a class A+ system and home comfort can be governed by remotely via APP for smartphones and tablets. The boilers are equipped with a special high-head fan designed to be able to pipe flues with Ø 60 mm or Ø 50 mm flues. Front access condensing heat exchanger ( New ! ) The Exclusive Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. Modulation 1:10 The range offers a wide range of modulation to respond to real energy needs, while simultaneously offering a high reduction in consumption. Beretta realizes this system through a totally pneumatic and therefore safe and reliable model. The electronics in fact act only on the number of fan revolutions (inlet air flow rate) without intervening on the injection of the gas quantity which is automatically sucked in. Beretta therefore introduces a new double distribution mixer: a mechanical damper with a calibrated weight which opens or closes a part of the section of the venturi so as to divide the modulation range into two stages (smaller section with low air flow rates or larger section with high air flow rates). Beretta has also developed a specific silencer in the air intake to reduce any resonances generated by the new mixer. Warranty All products for sale on our site are new and packed. The guarantee yes

Read more less

Technical features Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Heating nominal heat input: 25 kW Sanitary nominal heat input: 30 kW Classification European Directive EEC 92/42: **** Quantity of hot water with Δt=25°C: 17 l/min IPX5D electrical protection degree Nox class: 5 Power supply: methane Characteristics The new Beretta boiler is made up of a new type of front access exchanger, made up of a single seamless aluminum tube, thus making the thermal resistance of aluminum higher than steel, allowing for uniform temperature distribution. In addition, this accurate serial circuit allows a large part to be prepared for the passage of water, reducing pressure drops and preventing the deposit of impurities, thus allowing excellent performance over time. In addition, with MYNUTE, it is equipped with a 50mm smoke outlet approval. For periodic cleaning, the boiler has an accurate system of guides which facilitates the assembly and disassembly of the drawer. Finally, for the management of the device there are two knobs, one for regulating the temperature and the other for domestic hot water, and a display that shows all the functions which is very simple to use. For filling the system, it has a filling cock and a visible filling hydrometer. FLEX modulating circulators: The MYNUTE RAIN boiler works with an electric motor of the circulator with an Energy Efficiency of 0.20, also having such a significant energy savings compared to traditional boilers. It is also possible to modify, if greater heating is required, the head of the circulator with a larger one (FLEX). Dimensions: (HxWxD): 797x553x274mm

Read more less

GAS BOILER BERETTA METEO 24 CAI AG METHANE OPEN CHAMBER -NEW ErP Technical features Product code: 20101258 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary energy efficiency profile XL Class B Characteristics of heating/DHW operation: Heating/DHW nominal heat output: 24 kW Quantity of hot water with Δt=25°C: 14 l/min Dimensions (hxwxd) mm 760 x 494 x 240 METHANE power supply Legend: C (heating + sanitary water), A (Open Room) I (electronic ignition, ionisation control). AG Antifreeze as standard down to -15°C WEATHER - ErP Meteo is a complete range of specific boilers for outdoors. The high technological content enhances the specific characteristics to the maximum: dimensions, standard remote control panel, resistance to external agents, innovative performance. The quality of the materials and the innovative design of the shell add elegance to these very small and high performance boilers. Extremely reliable and simple to use, the Meteo range boilers were created specifically for outdoor installations. The unique shell structure, IPX4D electrical protection and materials used for the shell provide maximum protection from external agents. The streamlined, modern aesthetic allows water to roll off. The installation is facilitated by reduced dimensions and supplied equipment. Designed for installations on balconies, Meteo, with a depth of only 24 cm, is the ideal answer to space problems; it is equipped as standard with fittings for connection to the system, gas and sanitary taps and a positioning template. The remote control panel, supplied as standard, allows total control of the boiler from inside the home. The main functions are simple and immediate, with many other user-customizable settings. The remote control panel also functions as a chronothermostat weekly and is set up for climate control via an external probe (optional). Characteristics: CAI boilers, ErP version, equipped with low consumption circulator (EEI0.20) modifiable up to 7m head MIX combustion (Air/Gas): constant efficiency (mod. CSI) Built with specific materials for outdoor use REC 05 remote control panel as standard ø 60 fume exhaust adapter with standard air intake (mod. CSI) Standard antifreeze up to -15 °C IPX4D electrical protection degree Arrangement for climatic thermoregulation Plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. FOR CONVERSION TO LPG, CONTACT YOUR LOCAL AUTHORIZED ASSISTANCE CENTER IN ADVANCE Beretta MYNUTE X 30C Low NOx condensing boiler complete with flue gas exhaust kit 20163565 LPG - NEW Boiler code 20163565 Seasonal heating energy efficiency class A Sanitary ware energy efficiency class A Declared load profile XL NOx emission class 6 WARM-UP EXERCISE Heating thermal capacity (max-min) kW 25.00-4.90 Maximum pressure-temperature bar-°C 3 - 90 Membrane expansion vessel capacity 9 l HEALTH EXERCISE Nominal ACS heat output (max-min) kW 30.00-4.90 ACS energy efficiency ηwh % 85 DHW production at ∆T= 25°C / 30°C / 35°C l/min 17.2/14.3/12.3 LINKS Heating inlet - outlet Ø 3/4” Sanitary inlet - outlet Ø 1/2” Gas inlet Ø 3/4” DIMENSIONS, WEIGHT Boiler dimensions (HxDxL) mm 740x420x275; 35 Kg MYNUTE X BERETTA PRESENTS MYNUTE X, THE NEW RANGE OF CONDENSING BOILERS, WITH MANY INNOVATIVE AND ADVANTAGEOUS FEATURES From the stainless steel primary exchanger to the modern electronic interface, there are numerous new elements that distinguish MYNUTE X in the Beretta offer. The new condensing range, with its 5 models from 20 to 35 kW, with “combined” and “heating only” versions, meets every need for residential comfort. High efficiency, low consumption and ease of installation make MYNUTE X the winning choice, both for new homes and for the replacement market. With MYNUTE X, the novelty of the project merges with the tradition of excellence of Beretta, matured in almost half a century of experience in the domestic comfort sector. Its aesthetics, in line with the Beretta style of the latest generation products, easily integrates into any living context, thanks also to its compactness and installation flexibility. NEW DIGITAL INTERFACE MYNUTE X is equipped with a modern and user-friendly control panel, elegantly covered by a door that allows you to glimpse the light of its “green gem”, the LED light bar that indicates its current operating status. Through a modern backlit LCD display, which communicates with the user through icons and scrolling texts (multilingual), it is possible to access the functions of MYNUTE X. Through 7 silk-screened operating keys, it is possible to navigate the panel in a simple and intuitive way, accessing the settings and parameterizations of the boiler and the system. MYNUTE X FUNCTIONS MANAGEMENT OF UP TO 2 HYDRAULIC CIRCUITS, HIGH AND/OR LOW TEMPERATURE, THROUGH SPECIFIC PREHEATING ACCESSORIES PREHEATING ACTIVATION TO REDUCE WAITING TIMES FOR HOT WATER CLOCK FUNCTION WEEKLY PROGRAMMING INTEGRATED IN THE DISPLAY POSSIBILITY OF CONNECTION WITH HOT WATER BOILER (R MODELS) Technology and advantages NEW STAINLESS STEEL PRIMARY EXCHANGER THE NEW MYNUTE X EXCHANGER IS MADE OF STAINLESS STEEL, WITH A SMOOTH PIPE WITH A HIGH SECTION TO OFFER THE BEST EFFICIENCY AND CLEANLINESS OVER TIME. AISI 304 L stainless steel, in addition to its high resistance to the corrosive action of acid condensation, reduces the internal formation of oxides and other electrochemical phenomena typical in installations on old systems. The single wound coil geometry (hydraulic circuit in series) offers a constant flow rate in all sections of the exchanger and intrinsically limits clogging phenomena. Front access facilitates periodic maintenance and cleaning operations of the combustion chamber. INTEGRATED CLAPET MYNUTE X is C10 approved * (formerly 3CEp approved), integrating the non-return valve (clapet) as standard on all models, making it “ready to install” in the case of installations in pressurized collective flues, for which the non-return valve is a mandatory device. The non-return valve is a specific device that allows combustion fumes to flow through the ducts in one direction only, i.e. from the burner to the flue outlet. Its function is therefore to prevent the fumes from returning to the combustion chamber, compromising the correct functioning of the boiler. This eventuality could occur for various reasons, for example in the case of overpressure in the duct of a collective flue system. The non-return valve is generally supplied as a specific optional kit, to be installed at the flue outlet of a boiler in the case of C10 type collective flues. In MYNUTE X the non-return valve is positioned inside the boiler (see detail), which translates into quick installation and reduced costs. HYBRID READY MYNUTE X is a HYBRID READY solution. The boiler is part of the HYBRID READY product range, which constitutes the new hybrid technology system conceived and developed in the Beretta Research Laboratories. This system, created to meet current and future needs for the integration and management of different energy sources (Gas/Electricity/Renewables), also includes the most innovative methods of energy storage and distribution. Characteristics INNOVATIVE STAINLESS STEEL CONDENSING EXCHANGER WITH FRONT ACCESS WIDE MODULATION RANGE (UP TO 1:8) LOW CONSUMPTION MODULATING CIRCULATOR (EEI ≤ 0.20), 6 m EQUIPPED WITH STANDARD SMOKE CLAPE (NON-RETURN VALVE) AND C(10) APPROVED.* LOW POLLUTING EMISSIONS: CLASS 6 (UNI EN 15502) MYNUTE X IS HYBRID READY: IT IS DESIGNED TO BE INTEGRATED INTO BERETTA MULTI-ENERGY SYSTEMS THROUGH THE REC 10H HYBRID AND THE CONNECT HYBRID, AVAILABLE AS ACCESSORIES INSTALLATION FLEXIBILITY: INDOOR, OUTDOOR** AND BUILT-IN INSTALLATION*** (IN A PARTIALLY PROTECTED PLACE) CLICK-FIT FLUE CONNECTION: FAST AND SAFE, WITHOUT THE NEED FOR AN EXTERNAL COLLAR ANTIFREEZE RESISTANCE KIT, HYDRAULIC CONNECTIONS AND EXTERNAL PROBE AVAILABLE AS ACCESSORIES ELECTRICAL PROTECTION DEGREE IPX5D “DOUBLE T” TEMPLATE SUPPLIED, COMPATIBLE WITH HYBRID CONNECTS FOR MANAGING UP TO TWO SYSTEM AREAS FOR GAS CONVERSION CONTACT THE AUTHORISED BERETTA TECHNICAL ASSISTANCE CENTERS COMPATIBLE WITH BeSMART WIFI COMFORT CONTROL AS A THERMOSTAT (OTBUS COMMUNICATION), ALLOWING THE MOST ADVANCED FUNCTIONS POSSIBILITY OF PIPETING FLUES WITH THE SPECIFIC PP FLUE PIPE Ø60 AND Ø50 Product Warranty The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Heating nominal heat input: 30 kW Heating nominal heat output: 29.13 kW Classification European Directive EEC 92/42: ★ ★ ★ ★ Sanitary comfort ★ ★ ★ Expansion vessel capacity: 10 l Quantity of hot water with Δt=25°C: 17.2 l/min Minimum domestic water flow rate: 2 l/min Sanitary water temperature selection range: 35 - 60°C Total electric power: 125W Electrical protection degree: IP X5D NOx emission class: 5 Power supply: methane Characteristics Modulation 1:10 Low consumption modulating circulator (Class A) Patented condensing exchanger (Patent Pending) in aluminum with high flow rate Thermoregulation with standard external probe Standard hydraulic fitting cover For gas conversion, contact authorized Beretta Technical Assistance Centres Dimensions Dimensions (HxWxD): 845x453x358 mm Weight: 42Kg

Read more less

Beretta EXCLUSIVE GREEN E 25 CSI condensing boiler complete with flue kit cod. 20104060 Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Heating nominal heat output: 21.44 kW Classification European Directive EEC 92/42: ★ ★ ★ ★ Sanitary comfort ★ ★ ★ (EN 13203) NOx emission class: 5 (UNI EN 677) Efficiency at rated power: 98.7% Efficiency at reduced load (30%): 109.6% Total electric power: 93W Electrical protection degree: iP X5D Expansion tank capacity: 9 lt Quantity of hot water with Δt=25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min Sanitary water temperature selection range: 35 - 60°C Dimensions (hxlxp) mm 845x453x358 ; 44kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionization control). EXCLUSIVE GREEN E HI-EFFICIENCY ECOLOGICAL CONDENSING WALL-MOUNTS The new Exclusive Green E condensing boilers , equipped with the innovative Beretta front exchanger, in addition to implementing the requests of the ErP standards, improve all the peculiarities confirming themselves as top of the range. Seasonal efficiency up to 94%, very wide modulation range (up to 1:10), low consumption modulating circulator with the possibility of increasing the head up to 7m and reduced consumption are some of the main features. The new Exclusive Green E boilers also offer excellent reliability and technology and, thanks to their high performance, are an excellent solution in hybrid systems with solar thermal and heat pumps. The external probe that allows you to activate the climatic thermoregulation is standard as standard. Furthermore, by adding the optional BeSMART WiFi Comfort Control kit and the LINK MODE interface board kit, Exclusive Green E constitutes a class A+ system and home comfort can be governed by remotely via APP for smartphones and tablets. The boilers are equipped with a special high-head fan designed to be able to pipe flues with Ø 60 mm or Ø 50 mm flues. Front access condensing heat exchanger ( New ! ) The Exclusive Green E boiler is equipped with the new Beretta condensing exchanger with front access . An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. Modulation 1:10 The range offers a wide range of modulation to respond to real energy needs, while simultaneously offering a high reduction in consumption. Beretta realizes this system through a totally pneumatic and therefore safe and reliable model. The electronics in fact act only on the number of fan revolutions (inlet air flow rate) without intervening on the injection of the gas quantity which is automatically sucked in. Beretta therefore introduces a new double distribution mixer: a mechanical damper with a calibrated weight which opens or closes a part of the section of the venturi so as to divide the modulation range into two stages (smaller section with low air flow rates or larger section with high air flow rates). Beretta has also developed a specific silencer in the air intake to reduce any resonances generated by the new mixer. Up to 19 m of ducting with Exclusive Green E 25 With Exclusive Green E it is possible to duct even the most "difficult" flues with ease thanks to the approval for Ø 50mm flues which is added to the traditional Ø 80 mm and Ø 60 mm ducting flues. The main 50mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. Flex modulating circulator, optimized performance, low consumption ( New ! ) Exclusive Green E uses a low energy consumption synchronous modulating circulator with an Energy Efficiency Index of less than 0.20, which means significantly reduced electricity consumption. The new circulator is set as standard to modulate proportionally to the power supplied by the boiler, thus contributing to a further reduction in electricity consumption. Alternatively, it can modulate with a constant ΔT logic in order to maximize the phenomenon of condensation in the exchanger. If necessary on the heating system, it is also possible to modify the maximum head which is normally set on the 6 m curve, opting for the 4 m, 5 m or 6 m curve without having to replace the circulator, from this characteristic comes the name "Flex". Smart management The control panel is the boiler management device. Simple and intuitive, it allows you to adjust the parameters and activate the numerous functions. A large liquid crystal display shows all important information. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The simple pressure of a key allows you to choose the season and, when the boiler asks for it, the Easy Filling function is activated by pressing a key. The panel integrates the Clima Facile function: thermoregulation and external probe as standard. Compatible with BE Smart ( New ! ) The BeSMART WiFi Comfort Control Panel, optional compatible with Exclusive Green E, is the remote boiler management device with modulating chronothermostat functions. With the WiFi Box accessory, included in the BeSMART WiFi Comfort Control, it is also possible to manage comfort remotely using Smartphones and Tablets. The BeSMART WiFi control is very simple to install and intuitive to use and allows you to adjust the parameters and activate the many functions on the boiler. A large liquid crystal display shows all important information. Using the buttons on the control, the temperature of the heating water and domestic hot water is set easily and intuitively and the heating time programming is carried out. Exclusive Green E and the optional BeSMART WiFi Comfort Control Kits and LINK MODE interface card form a class A+ system. Characteristics: Exclusive Green E* with the BeSMART WiFi Comfort Control (optional) or with the REC 07 Remote Control (optional) forms a class A+ system Compatible with the BeSMART WiFi Comfort Control for remote control via iOS or Android APP from Smartphone or Tablet Very high modulation (up to 1:10) New high-flow aluminum condensing exchanger with front access Low polluting emissions: class 5 (UNI EN 483) Low consumption modulating circulator (EEI≤0.20) 6 m head adjustable up to 7 m Thermoregulation with standard external probe Standard hydraulic fitting cover Possibility of intubating flues with the special flue in PP ø 60 (up to 23m) and ø 50 (up to 19m)** Template, plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres *except model 35E **model 25E Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Energy label specifications according to the European ErP directive Class B heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal heat input: 25 kW Classification European Directive EEC 92/42: **** Quantity of hot water with Δt=25°C: 14 l/min Dimensions (hxlxp) mm 780 x 400 x 336 METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control) Exclusive services: Mynute Sinthesi - ErP Mynute Sinthesi by Beretta is a wall-mounted condensing boiler for high temperature single-family systems. Continuous electronic modulation of the gas antifreeze device as standard (up to 0°C). Environmental Self-Regulation System (SARA). Mynute Sinthesi keeps all the peculiarities of the Mynute range unchanged but evolves towards new needs. The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this makes it possible to obtain very high performance in terms of efficiency and therefore significant energy savings. Mynute Sinthesi therefore represents the ideal solution both in the first installation and in the replacement. Characteristics: ErP boilers with 6 m low consumption circulator (EEI≤0.20) Specific for high temperature systems Condensing post exchanger in aluminum alloy IPX5D electrical protection degree Environmental Self-Regulation System (SARA) Hydraulic connections cover (optional) Template, plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.

Read more less

GAS BOILER BERETTA MYNUTE S 24 CAI METHANE OPEN CHAMBER - NEW ErP Product name BERETTA MYNUTE S 24 CAI CNG BOILER Technical features Product code: 20095667 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary energy efficiency profile XL Class B Characteristics of heating/DHW operation: Heating/DHW nominal heat output: 24 kW Quantity of hot water with Δt=25°C: 14 l/min Dimensions (hxwxd) mm 740 x 400 x 336 METHANE power supply Legend: C (heating + sanitary water), A (Open Room) I (electronic ignition, ionization control). MYNUTE S - ErP The benchmark for standard wall mounted boilers. The innovation: Designed to facilitate replacement The new Mynute S, a point of reference in the range of Beretta Clima standard wall-mounted boilers, is specifically designed to make installation particularly easy, especially when replacing with other products. The models in the Mynute S range comply with Legislative Decree 311/06. The reliable: Technology at the service of quality The new Mynute S offers highly reliable combustion and electronics and boasts the high degree of electrical protection IPX5D. The range is therefore characterized by safety and solidity thanks to the components with which it is made which belong to a high quality standard. The boiler features the most innovative safety devices: control systems that monitor the presence of the flame, on the correct evacuation of fumes, on temperatures and pressures. The anti-blocking cycles of the circulator and the board anti-freeze system allow the appliance to last longer over time. The new Mynute S also boasts the Survivor Function which allows it to continue to function in the event of a failure of the sanitary NTC probe. The elegant: A modern style that integrates with any environment The new Mynute S is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to perform all the functions necessary for using the boiler. Characteristics: CAI boilers, ErP version, equipped with low consumption circulator (EEI20) Specifically designed to facilitate the replacement of pre-existing wall-mounted boilers 9 liter expansion vessel Simple and intuitive digital display Arrangement for climatic thermoregulation (optional external probe) Can be interfaced with the REC 08 Remote Control Panel (optional) IPX5D electrical protection degree Plumbing fittings, gas and sanitary taps (optional) For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

GAS BOILER BERETTA MYNUTE S 28 CAI LPG OPEN CHAMBER - NEW ErP Technical features Product code: 20102088 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary energy efficiency profile XL Class B Characteristics of heating/DHW operation: Heating/DHW nominal heat output: 28 kW Quantity of hot water with Δt=25°C: 16 l/min Dimensions (hxwxd) mm 740 x 452 x 336 METHANE power supply Legend: C (heating + sanitary water), A (Open Room) I (electronic ignition, ionization control). MYNUTE S - ErP The benchmark for standard wall mounted boilers. The innovation: Designed to facilitate replacement The new Mynute S, a point of reference in the range of Beretta Clima standard wall-mounted boilers, is specifically designed to make installation particularly easy, especially when replacing with other products. The models in the Mynute S range comply with Legislative Decree 311/06. The reliable: Technology at the service of quality The new Mynute S offers highly reliable combustion and electronics and boasts the high degree of electrical protection IPX5D. The range is therefore characterized by safety and solidity thanks to the components with which it is made which belong to a high quality standard. The boiler features the most innovative safety devices: control systems that monitor the presence of the flame, on the correct evacuation of fumes, on temperatures and pressures. The anti-blocking cycles of the circulator and the board anti-freeze system allow the appliance to last longer over time. The new Mynute S also boasts the Survivor Function which allows it to continue to function in the event of a failure of the sanitary NTC probe. The elegant: A modern style that integrates with any environment The new Mynute S is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to perform all the functions necessary for using the boiler. Characteristics: CAI boilers, ErP version, equipped with low consumption circulator (EEI20) Specifically designed to facilitate the replacement of pre-existing wall-mounted boilers 9 liter expansion vessel Simple and intuitive digital display Arrangement for climatic thermoregulation (optional external probe) Can be interfaced with the REC 08 Remote Control Panel (optional) IPX5D electrical protection degree Plumbing fittings, gas and sanitary taps (optional) For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee The warranty on this item is 24 months from the date of purchase.

Read more less

GAS BOILER BERETTA MYNUTE S 28 CAI LPG OPEN CHAMBER - NEW ErP Technical features Product code: 20102088 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary energy efficiency profile XL Class B Characteristics of heating/DHW operation: Heating/DHW nominal heat output: 28 kW Quantity of hot water with Δt=25°C: 16 l/min Dimensions (hxwxd) mm 740 x 452 x 336 METHANE power supply Legend: C (heating + sanitary water), A (Open Room) I (electronic ignition, ionization control). MYNUTE S - ErP The benchmark for standard wall mounted boilers. The innovation: Designed to facilitate replacement The new Mynute S, a point of reference in the range of Beretta Clima standard wall-mounted boilers, is specifically designed to make installation particularly easy, especially when replacing with other products. The models in the Mynute S range comply with Legislative Decree 311/06. The reliable: Technology at the service of quality The new Mynute S offers highly reliable combustion and electronics and boasts the high degree of electrical protection IPX5D. The range is therefore characterized by safety and solidity thanks to the components with which it is made which belong to a high quality standard. The boiler features the most innovative safety devices: control systems that monitor the presence of the flame, on the correct evacuation of fumes, on temperatures and pressures. The anti-blocking cycles of the circulator and the board anti-freeze system allow the appliance to last longer over time. The new Mynute S also boasts the Survivor Function which allows it to continue to function in the event of failure of the sanitary NTC probe. The elegant: A modern style that integrates with any environment The new Mynute S is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to perform all the functions necessary for using the boiler. Characteristics: CAI boilers, ErP version, equipped with low consumption circulator (EEI20) Specifically designed to facilitate the replacement of pre-existing wall-mounted boilers 9 liter expansion vessel Simple and intuitive digital display Arrangement for climatic thermoregulation (optional external probe) Can be interfaced with the REC 08 Remote Control Panel (optional) IPX5D electrical protection degree Plumbing fittings, gas and sanitary taps (optional) For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee The warranty on this item is 24 months from the date of purchase.

Read more less

BERETTA METEO 28 CAI AG METHANE BOILER - NEW ErP 2015 Cod. 20101259, OPEN ROOM WITH NATURAL DRAFT: CAI boilers specific for outdoor use, ErP version, equipped with low consumption circulator (EEI0,20). Technical specifications Product code: 20101259 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitaryware energy efficiencyprofilXL Class B Characteristics of heating/sanitary exercises: Heating/DHW nominal heat output: 28 kW Quantity of hot water with t=25øC: 16 l/min Dimensions (hxwxd) mmÿ760 x 553ÿx 240 METHANE power supply Legend:ÿ C (heating + sanitary water),ÿ A (Open Room) I (electronic ignition, controls ionization). AGÿAntifreeze fine series -15øC Features list ErP WEATHER ÿMeteoÿ is a complete range of specific boilers for outdoor use. The high technological contents enhance the specific characteristics to the maximum: dimensions, standard remote control panel, resistance to external agents, innovative performance. The quality of the materials and the innovative design of the shell add elegance to these extremely small and high performance boilers. Extremely reliable and simple to use, the boilers in the Metesonnate range are specifically designed for outdoor installations. The exclusive shell structure, the IPX4D electrical protection and the materials used for the coat provide maximum protection from external agents. The streamlined, modern aesthetic allows water to roll off. Installation is facilitated by reduced dimensions and supplied equipment. Designed for installations on balconies, Meteo, with a depth of only 24 cm, is the ideal answer to space problems; equipped as standard with fittings for connection to the system, gas taps and sanitary fixtures with positioning template. The remote control panel, supplied as standard, allows total control of the boiler from inside the home. The main functions are simple and immediate, with many other settingsÿcustomizable by the user. The remote control panel also functions as a chronothermostat weekly and prearranged for climate control via an external probe (optional). Characteristics: CAI boilers, ErP version, equipped with low consumption circulator (EEI0,20)ÿadjustable up to 7m headÿ MIX combustion (Air/Gas): constant performance (mod. CSI)ÿ Built with specific materials for outdoor useÿ Remote control panel REC 05ÿ as standard Exhaust adapter ÷ 60 with standard air intake (mod. CSI)ÿ Standard antigelfine -15øCÿ Electrical protection degrees IPX4Dÿ Arrangement for climatic thermoregulationÿ Plumbing fittings, gas taps and sanitary fittingsÿ For gas conversion, contact authorized Beretta Technical Assistance Centres Beretta or ERP. The concrete commitment to a sustainable future The acronym ÿErP, acronym of Energy related Products?ÿ (Products connected to the use of energy), identifies Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015, the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and the production of domestic hot water with a lower rated thermal power equal to 70 kW can be placed on the market with an ÿenergy labelÿthat highlights theÿefficiency class*. Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility of identifying it facilitates the level of efficiency of a product by being able to carry out a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data reported for climatic bands. In addition to the product labels, the European regulation has provided for the creation of a "system label" in the case of manufacturing plants with various appliances, components and related controls. This second type of labelling, thanks to the virtuous synergy between the various elements, will make it possible to create systems capable of achieving levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to less than 400kW, will prevent inefficient products from being placed on the market. Also for DHW tanks there will be an obligation to respect minimum heat loss limits. For primary water tanks, these will be subject to compliance with an energy classification based on heat loss. For sanitary accumulations, up to 500 liters there will be the obligation of labelling, from 500 to 2000 liters they will be bound to respect the energy classification. For heat pumps for heating and for mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. In order to be placed on the market, gas-fired water heaters with solar heat pumps, in addition to energy labelling, will also have to comply with a series of requirements in terms of efficiency. Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.

Read more less