THE BOILER WILL BE SUPPLIED WITH METHANE WITH THE LPG CONVERSION KIT INCLUDED, WHICH MUST BE INSTALLED BY THE SERVICE CENTER DURING FIRST IGNITION. IN CASE OF UNAVAILABILITY OF THE ITEM, THE NEW LOW NOX AVANT BLUE MODEL WILL BE SHIPPED BAXI LUNA3 AVANT+ 240 Fi LPG CONDENSING GAS BOILER COMPLETE WITH FUME EXHAUST KIT -ErP ______________________________________________________ Technical features ErP energy efficiency class (heating and DHW): A - B Load profile: XL Heating/DHW nominal heat input kW 24.8 Heating/DHW nominal heat output kW 24 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 96.8% Efficiency at 100% Pn (50-30°C): 101.6% Minimum operating temperature °C -5 Expansion/pre-charge vessel capacity l/bar 8/0.8 Sanitary water temperature adjustment °C 35-65 Sanitary water production ∆T 25°C l/min 13.7 Minimum domestic water flow rate I/min 2 Degree of protection: IPX5D Electric power W 122 Dimensions (hxwxd): 763x450x345 mm ; 43.5 kgs Power supply: LPG ____________________________________________________________________ Luna3 Avant+ Wall mounted condensing boiler ideal for replacement in high temperature systems Baxi introduces the new Luna3 Avant+ 240 Fi condensing boiler which re-proposes the best characteristics of the Luna3 range of conventional boilers (sanitary performance, reliability and installation versatility) combined with the advantages and performance of a condensing boiler. Luna3 Avant+, in fact, is equipped with an aluminum alloy condensing post-exchanger (recovery) which recovers the latent heat of condensation, which in traditional boilers is instead dispersed with the exhaust gases. The exchanger-recovery, positioned inside the boiler at the top right, is directly connected to the fan which pushes the fumes inside, where they condense in contact with the system return water, before being expelled. Characteristics: High efficiency circulation pump Arrangement for combination with the Baxi integrated solar system Same settings as a traditional boiler (the analyzer is not necessary to adjust the gas valve) Operation on methane (possibility of operation on LPG with conversion kit) Control panel with multifunction LCD display STANDARD climate control (with optional external probe) Aluminum alloy condensing post-exchanger _________________________________________________________________ Product Warranty: The warranty on this item is 24 months from the date of purchase.

Read more less

Baxi AVANT BLUE 24 Fi condensing boiler Low NOx 6 complete with flue kit cod. 7733702 LPG - NEW Baxi brand Model Avant Blue 24 FI Product Code 7733702 Power 24 kW Energy class A Condensation type Heating/DHW nominal heat input kW 24.8 Sanitary nominal thermal power kW 24 Emissions of nitrogen oxides NOx mg/kWh 18 Sanitary water production ∆T 25°C l/min 13.7 Minimum domestic water flow rate l/min 2 LPG supply Combustion Chamber Sealed chamber/Forced draft Degree of protection IPX5D Dimensions (LxHxP) - Weight 450x763x345 mm Weight; 43.5 kgs AVANTBLUE Baxi Avant Blue FI 7724370 NOx6 24 kW ErP natural gas, the condensing boiler with energy class A Low NOx emissions: class 6 according to EN 15502 Modulating fan Aluminum alloy condensing post-exchanger Sturdy and reliable: brass hydraulic unit with turbine sanitary sensor for optimal comfort and large passage copper exchanger Arrangement for combination with the Baxi integrated solar system Same settings as a traditional boiler (the analyzer is not necessary to adjust the gas valve) Control panel with multifunction LCD display hydraulic system Brass hydraulic unit with electric three-way diverter valve and turbine sanitary sensor Steel burner Copper water/fume exchanger Sanitary heat exchanger in stainless steel Aluminum alloy condensing post-exchanger High efficiency circulation pump Pump anti-blocking system and 3-way valve (which intervenes every 24 hours) Pump post-circulation Automatic by-pass Built-in condensate drain siphon Thermoregulation system Climatic adjustment (external probe available as an option) Heating circuit temperature adjustment DHW circuit temperature adjustment Remote control and climatic regulator available as an accessory, both in wired and wireless versions Control system Safety thermostat against overheating of the water/fumes exchanger Hydraulic pressure switch which blocks the boiler in case of water shortage Safety air pressure switch for checking correct smoke evacuation Temperature control using NTC probes. Pressure indicator Electronic thermometer Total antifreeze protection Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

GAS BOILER SAUNIER DUVAL THEMAFAST 4 CONDENSING WI-FI 26 25 kW METHANE COMPLETE WITH FUME EXHAUST KIT - NEW ERP Model: ErP efficiency class: A+ Sanitary load profile: XL Type: Heating and domestic hot water Combustion chamber: sealed Domestic hot water production technology: AquaspeedFAST® Heating Nominal power P min/max heating 80/60 °C: kW 5.1/24.5 Partial load efficiency 30% 40/30 °C %: 108.4 Sanitary Rated power min/max (60 °C): kW 5.1/25.5 Specific flow rate (∆T=25 K): l/min 15 Continuous flow rate (∆T=30 K): l/min 12 Min/max DHW temperature: 38/60 °C Electrical characteristics Total absorbed electric power: W 137 Supply voltage/frequency: V/Hz 230/50 Dimensions: Dimensions (hxwxd): 740 x 418 x 344 mm Methane or LPG supply (Transformation through the Assistance Centre) THEMAFAST 4 CONDENSING Complimentary MiGO Wi-Fi Modulating Climatic Control Unit ThemaFast 4 Condensing boilers can count on the exclusive Aquaspeed FAST® system for the production of domestic hot water combined with condensing technology which ensures immediate and continuous availability of domestic hot water for superior comfort by eliminating unnecessary waiting times. The range includes 3 models of 25.30 kW and 35 kW. Characteristics: Energy classification 4 stars ****(92/42/EEC) with yields up to 109.2%; Sanitary comfort 3 stars ***(EN 13203-1), thanks to the exclusive Aquaspeed FAST® technology with sanitary stainless steel plate heat exchanger and integrated micro-accumulator which allows immediate delivery of hot water thanks to the available reserve. Control panel with backlit digital display, easy to use: the user can easily select the desired functions and temperatures. Solar Easy: all models in the ThemaFast 4 Condensing range are compatible with all solar systems thanks to a series of solar kits. The small dimensions make all ThemaFast 4 Condensing models perfect both for replacement and for installation in newly built systems. Continuous domestic hot water (DHW) production up to 20 l/min Low NOx emissions - class 5 (EN 483) Total premix burner and primary heat exchanger in anti-corrosion stainless steel High efficiency and modulating circulator Heating system antifreeze function Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview BIASI INOVIA COND E 25S LPG CONDENSING BOILER - NEW ErP, SEALED CHAMBER COMPLETE WITH FUME EXHAUST KIT: Wall mounted condensing boilers. The premixed range is simple on the outside and technological on the inside. The sites displaying the Biasi web sales authorized brand have been authorized by BSG Caldaie a Gas SpA for the sale of Biasi products. These companies therefore release the conventional guarantee. Technical specifications o Model: Inovia Cond E 25S Energy label specifications according to the European ErP directive o Class A heating energy efficiency o Sanitary energy efficiency Class A o Withdrawal profile: XL Characteristics of heating/DHW operation: o DHW useful thermal power: 24.4 kW o Useful thermal power for heating: 19.5 kW o Nominal kW heat input(*): 25 kW o Efficiency at 100% load: 106.2% o Sanitary flow rate t =25°K: 15.9 l/min o High yields (in compliance with yield directive 92/42 CEE and Legislative Decree 311/06) o Sanitary comfort (EN 13203) o Total premix burner, built in stainless steel (Class NOx 5) o Sanitary plate heat exchanger in stainless steel o High efficiency pump with low energy consumption o IPX5D degree of protection o Dimensions hxwxd: mm 700 x 400 x 290; 32kg o LPG power supply Main features Inovia Cond E Premixed condensing boilers Inovia Cond E represents the new premixed BIASI condensing boiler. Inovia Cond E is equipped with innovative aesthetics and a new interface that is immediate and easy to use, it is equipped with new functions that make it an integral part of a system and which facilitate its installation and maintenance. Inovia Cond E offers all the advantages of condensing technology: great performance, high efficiency, energy saving and respect for the environment thanks to reduced polluting emissions such as NOx and CO. Installed in low temperature systems, they allow savings of up to 30%. Characteristics: o • High yields (in compliance with yield directive 92/42 EEC and Legislative Decree 311/06) or • Sanitary comfort (EN 13203) o • Primary condensing exchanger in stainless steel with plastic coating to offer maximum resistance to corrosion o • Total premix burner, built in stainless steel (Class NOx 5) or • Sanitary plate heat exchanger in stainless steel or • High efficiency pump with low energy consumption or • IPX5D degree of protection or • Can be installed in a partially protected place or • Integration with BIASI solar systems, using a solar kit o • Innovative digital control panel with graphic interface and buttons or • Digital pressure reading by pressure transducer or • Arrangement for remote control and external probe or • Possibility of remotely managing a zone valve in the case of multi-zone systems. Control panel: o Summer/winter/off selector o Heating temperature regulator o DHW temperature regulator o Digital pressure reading o Domestic hot water and heating temperature visualization from the display o Visualization of fault diagnostics, block status and fault history o Recommended filling view and filling guide o View months left until annual maintenance is due o External temperature display (with external probe connected) and signaling of external probe connected and K value set o Display of flame modulation o Visualization of the BIASI SOLCONTROL solar control unit connected to Inovia Cond E, active solar pump and solar integration o DHW comfort function selectable by means of a dedicated and programmable key o Direct access to the INFO menu dedicated to the user. Fiscal detraction As a condensing boiler, Inovia Cond E allows you to take advantage of the tax deduction according to current legislation. d Thermoregulation By connecting the external probe (optional) directly to the boiler, climatic regulation can be used. Inovia Cond E will adapt the system water temperature to the external climatic conditions, ensuring that the desired room temperature is reached without waste and optimizing consumption. The boiler is equipped with a complete set of curves which can be accessed by entering programming. The curve is simply chosen from the control panel. Solar management Inovia Cond E integrates solar management directly into the product. Thanks to the integrated solar management it is possible to connect the SOLCONTROL control unit and view the status of the pump and the relative solar integration. Zone management Inovia Cond E features the zone management card as standard which allows you to manage a zone valve using the BIASI remote control. In the case of a system with several high temperature zones, one zone can be managed by remote control and the other zones can be managed by chronothermostats. This allows you to select two thermoregulation curves, one in the boiler and the other in the remote control. All the zones controlled by chronothermostats will be managed by the thermoregulation curve set in the boiler, the zone controlled by the remote control will be managed by the thermoregulation curve set therein. In the case of multi-zone systems at high and low temperatures, it is recommended to use the BIASI MULTIzone system manager. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the Eco-Design Directive (ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: or generators with a capacity of less than 400 kW or water heaters with a capacity of less than 400 kW, or kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows them to compare the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: o product energy label; o product data sheet; o system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; o technical data sheet of the system with the parts relating to the product or the system already completed. o Dealer liability First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: o all appliances and/or systems are equipped with the respective labels and make sure that they are clearly visible; o all devices and/or systems are always accompanied by the mandatory technical data sheets; o any type of advertising, promotional or technical material in which energy data or price indications are shown, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

SAUNIER DUVAL DUOTWIN CONDENSING 25-100 WITH ACCUMULATION 100 l COMPLETE WITH SMOKE KIT - NEW ERP Model: ErP efficiency class in heating/DHW: A Sanitary load profile: XL Type: Heating and domestic hot water Combustion chamber: sealed Domestic hot water production technology: Shift-Load Heating Nominal power P min/max heating 80/60 °C: kW 3.4/27 Partial load efficiency 30% 40/30 °C %: 108 Sanitary Rated power min/max (60 °C): kW 3/25 Specific flow rate (∆T=25 K): l/min 14.4 Continuous flow rate (∆T=30 K): l/min 24.4 Min/max DHW temperature: 35/65 °C Electrical characteristics Total absorbed electric power: W 105 Supply voltage/frequency: V/Hz 230/50 Dimensions: Dimensions (h x w x d): 1320 x 600 x 698 mm CNG code (G20) - 10014619 METHANE version DUOTWIN CONDENSING DuoTwin Condensing is extremely efficient from every point of view and, thanks to the "Shift-Load" system, guarantees a great availability of DHW. A 25 kW model is available with an integrated 100-litre boiler. Characteristics: Energy classification 4 stars ★★★★ (92/42/EEC) with efficiency up to 108%; Sanitary comfort 3 stars ★★★ (EN 13203-1), thanks to the "Shift-Load" technology for the production of stratified DHW, with high efficiency oversized sanitary exchanger with 20 stainless steel plates and 100 liter storage tank. Efficiency at 360°: thanks to the wide 1:8 modulation, the burner can modulate from 25 to 3 kw thus avoiding useless and inefficient On/Off cycles, keeping the efficiency values ​​constant over time at 108%. Even from an electrical point of view, consumption in stand-by is minimal: 2.3 Watts. The insulation of the boiler allows very low heat losses: 1.38 kwh/24h. Continuous domestic hot water production (DHW) up to 14.4 l/min (DT 25 K) Low NOx emissions - class 5 (EN 483) Total premix burner with high modulation and primary heat exchanger in anti-corrosion stainless steel High efficiency and modulating circulators (main and sanitary). antifreeze function Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ARISTON CLAS PREMIUM EVO 35 EU BOILER COMPLETE WITH LPG/METHANE FUME EXHAUST KIT Product code: 3300699 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 31/7.0 Max/min heating thermal power (80°C-60°C) kW 30.2/6.8 Efficiency at nominal heat input (60/80°C) % 97.6 Efficiency at nominal heat input (30/50°C) % 106.4 Efficiency at 30% at 30°C % 10.9 Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Specific flow rate in DHW (10 min. with ?T=30°C) litres/min 16 Quantity of hot water ?T=25°C litres/min 19.3 Quantity of hot water ?T=35°C litres/min 13.8 Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 77 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 770/400/385 CNG or LPG power supply Kit for conversion from methane to propane supplied Wall mounted condensing boiler with auto function The Clas Premium Evo wall-mounted boiler, a new solution for domestic comfort that integrates the range of condensing boilers, the innovative technology capable of reusing the energy of exhaust fumes, increasing thermal efficiency and eliminating waste.Clas Premium Evo it stands out for its innovative and captivating design and for its small size that makes it suitable for any type of furniture. It is available in the heating and domestic hot water production version in 2 powers: 24-30 kW (sealed chamber). Characteristics: Backlit multifunction LCD screen Modulation ratio 1:4 Guaranteed acoustic comfort thanks to the new silencer Oversized modulating circulator Isothermal primary heat exchanger in stainless steel o Increased DHW exchanger Possibility to see all the detailed information on operation, performance and services, always available on the LCD screen. Product characterized by high energy performance, reduction of consumption and polluting emissions. Cold water inlet and heating return filters Arrangement for integration with system configuration through the new bridgnet® bus communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management 60mm split exhaust Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons Acoustic comfort Acoustic comfort is further guaranteed by the introduction of the new silencer. For the Clas Premium Evo thanks also to the high modulation ratio of 1:10, the continuously modulating pump and the presence of side sound-absorbing panels. High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features ErP energy efficiency class (heating and DHW): A Load profile: XL DHW nominal heat input kW 24.7 Heating nominal heat input kW 20.6 Sanitary nominal thermal power kW 24 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.7% Efficiency at 100% Pn (50-30°C): 105.4% Expansion/pre-charge vessel capacity l/bar 8/0.8 Sanitary water temperature adjustment °C 35-60 Sanitary water production ∆T 25°C l/min 13.8 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions (h x w x d): 760 x 450 x 345 mm ; 38.5 kgs Power supply: CNG or LPG *Operation on LPG through adjustment by the Authorized Assistance Centre Moon Platinum+ Wall mounted condensing gas boilers for heating only and instant DHW production. Ecodesign and Labeling - From Baxi research comes a complete range of condensing boilers with high technological content designed in compliance with the requirements of the Ecodesign and Labeling directives, to ensure maximum domestic comfort. Latest generation electronics, high efficiency and compact design make the Platinum+ range the ideal solution for both new installations and replacement. THINK raises system efficiency - The Platinum+ range of boilers is designed with the Think technology platform - intelligence within, an exclusive system that makes them "think" intelligently! With this authentic "the brain inside the box", the Baxi proposal confirms itself as the intelligent choice for making the boiler communicate in a simple and flexible way with all the main heating technologies, creating increasingly complex and energy-efficient design solutions. Furthermore, the Think platform makes the boiler very easy to use, in line with the Baxi design tradition aimed at totally user-friendly management of the appliance. Even the least experienced user can thus interact with the new control panel and program his own domestic comfort with the utmost simplicity. With the range of condensing boilers with the Think platform, Baxi comfort is easy and smart. The combination of the Platinum+ boiler for heating and DHW production and THINK controls for intelligent management of the system allows efficiency to be raised to class A+. The Platinum+ range is equipped AS STANDARD with a removable control panel for remote management (wired or wireless) of the boiler, equipped with a large multifunction text display with modulating thermoregulation control unit functions. GAC - The innovative automatic combustion control system GAC (Gas Adaptive Control) guarantees a wide modulation range up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adapt the thermal power produced to the effective power dissipated by the building avoiding excessive overheating/cooling of the building. Efficiency and savings - The objective of a heat generator is to supply the energy necessary to the rooms to maintain maximum comfort conditions inside: this means supplying the rooms, through the system, with the same amount of heat the building disperses. In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. Total modulation pump The Luna Platinum+ range is renewed with the introduction of a high efficiency electronic pump with permanent magnet motor. The new fully modulated pump allows, compared to using a pump traditional modulating: Lower electricity consumption Better performance Greater durability Plant deaeration New electronic "system deaeration" function to facilitate the removal of air during initial ignition. Efficiency and savings The objective of a heat generator is to supply the energy necessary to the rooms to maintain conditions of maximum comfort inside them: this means supplying the rooms, through the system, with the same amount of heat that the building loses . In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. The graph shown above highlights the reduction in on/off cycles which distinguishes the new Platinum+ boilers with modulation up to 1:10 compared to a condensing boiler with lower modulation. The reduction of the on/offs determines an improvement in the efficiency of the boiler and consequently a considerable saving for the end user. Standard condensing boilers, on the other hand, with a limited modulation range work at a minimum power level above 6 kW; this allows it to avoid the on/off cycles for only 3% of the period of operation in heating, compromising the performance of the boiler and the life of the components. GAC : Gas Adaptive Control The electronics and the gas valve with stepper motor that the new Platinum+ boilers are equipped with guarantee automatic combustion control which is based on: on the flame signal The system continuously measures the flame signal during boiler operation and adjusts the gas flow rate so as to maintain the quality of combustion constant and all this without requiring any additional component inside the combustion chamber. Installers and end users enjoy the following benefits of the GAC: The automatic combustion control favors a reduction in installation times as no manual adjustment of the gas valve or nozzle change is required: in fact, it is sufficient to manually modify some parameters of the electronic board for operation with LPG The boiler self-adapts to the quality of the gas and the length of the flue gas outlets: this means that there are no manual adjustments to make High modulation field 1:10: high efficiency and savings, since such a wide modulation field determines a greater adaptability of the boiler to the thermal dispersions of the building to obtain a higher efficiency and greater durability of the components. The reduction of the on/off cycles, in addition to the greater efficiency, guarantees less noise produced by the boiler Unlike traditional condensing boilers, the boiler always works adjusted to maximum efficiency values ​​favoring a reduction in gas consumption and consequently a lower environmental impact thanks to the control of CO/CO2 emissions Power sets The term Power set identifies the heating power regulation process according to the project data. The thermal capacity of the boiler, through the Power set device, is adjusted according to the energy requirement: just act on the control panel to adjust some parameters. Full soundproofing C structure Silence is the relative or absolute absence of sound or noise. The noise level of the Luna Platinum+ boiler is comparable to a normal conversation. Digital pressure gauge The electronic pressure transducer in the hydraulic unit allows you to check the pressure directly on the display. Double alarm level in the event of low pressure: a "warning" level in the event of low pressure in the boiler; a "block" level in the event of a lack of pressure. Intubation solution For the rehabilitation of flues Baxi has developed a system that allows easy ducting in existing flues thanks to a Ø50 mm exhaust pipe (for 24kW models) Characteristics: wide modulation range 1:10 greater efficiency and silence GAC (gas adaptive control): automatic combustion control high-efficiency circulation pump with total modulation removable and backlit control panel in wireless and wired version for wall installation, with large text display, adjustment knob and menu selection keys power set: heating power adjustment according to project data integrated electronic management for coupling to a solar system Ø50 mm exhaust pipe: solution for restoring flues - mod. 24 kW STANDARD installation kit (gas cock / DHW inlet / telescopic fittings) antifreeze function and IPX5D degree of protection Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: IN THE ABSENCE OF THE PRODUCT THE FOLLOWING MODEL VMI 35 WILL BE SHIPPED VAILLANT ecoTEC PLUS CONDENSING BOILER VMI 346/5-5 with boiler COMPLETE WITH FUME KIT - ErP METHANE Technical features ErP energy class (Heating and DHW): class A Sanitary load profile - XL For heating and domestic hot water production Forced draft sealed chamber Nominal thermal power in sanitary kW 34 DHW nominal heat input kW 34 Performance stars (according to Dir. 92/42CEE) - **** Consumption at nominal power Natural gas m3 /h 3.7 Expansion vessel capacity 10 l Maximum water content in the system l 180 Storage tank setting temperature °C 35 - 65 Boiler nominal volume l 20 Minimum water flow l/min 1.5 Hot water withdrawal capacity (ΔT = 30K) l/10min 199 Domestic hot water comfort stars (prEN 13203) - *** Dimensions (hxpxl) mm 720x567x440; 59.5kg Power supply V/Hz 230/50 Total electric power W 115 Sound power dBA 49 IP degree of protection IP X4 D NOx class - 5 Version: CNG (0010019531) To view more product information CLICK HERE General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS with boiler Little space and a large family? ecoTEC plus with built-in wall-mounted boiler is the boiler designed to satisfy a high demand for hot water when spaces do not allow for the installation of external boilers. The VMW ecoTEC plus with actoSTOR CL 20 S integrable storage tank are available in power ratings of: 30 and 34 kW. This stratification boiler is a real hot water reserve that can be installed very easily and quickly directly between the wall and the boiler. An exceptional solution that ensures the quantity of water needed is always available and without sudden changes in temperature. The boiler system with storage tank is very simple to assemble: first install the actoSTOR CL wall-mounted storage tank and the related pipes supplied for domestic water, then hang the ecoTEC plus VMW wall-mounted boiler on the storage tank. The dimensions are very small 70cm high, 44cm wide and 55cm deep. The stratification storage tank guarantees the same performance as a storage tank with a 60-litre coil but with considerably reduced spaces. The combination with ecoTEC plus allows you to exclude the storage tank functionality by making the boiler work instantaneously; this allows a considerable saving on gas consumption. New electronics and a very high efficiency pump make ecoTEC plus the wall-mounted condensing boiler that consumes less on the European market. ecoTEC plus is compatible with all Vaillant components and accessories already on the market. The new design is simple and intuitive. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview CHAFFOTEAUX URBIA GREEN Ebus2 25 EU CONDENSING BOILER Cod. 3310407, COMPLETE WITH FUME EXHAUST KIT - NEW ErP: Wall-mounted condensing boilers with 4 liter mini-accumulator. Technical specifications Product code: 3310407 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Rated heat output max/min (Hi) Qn:ÿ22/2,5ÿkW Useful heating power80§ C/ 60§ C max/minÿ21,5/2,4ÿkW Useful heating power50§ C/ 30§ C max/minÿ23,4/2,6ÿkW Sanitary nominal thermal power max/min (60/80§C) PCI:ÿ25/ 5.5 kW Efficiency at nominal heat input:ÿ97.8% Efficiency 30% of nominal heat input:ÿ109.1% Energy efficiency stars: (dir 92/42/CEE) **** Capacity of the expansion vessel: 8 lt Maximum system water capacity: 100/300 litres Sanitary comfort stars(EN13203): *** Port. specific in healthcare (10 min. with T= 30øC): 13.2 l/min Hot water flow rate at T 25§ C: 14.6 l/min Degrees of protection for the electrical system:ÿIPX5D Nox class: 5 Dimensions hxwxd: mmÿ745 x 440 x 375ÿ; 42kg LPG fuel supply Features list URBIA GREEN Ebus2 EU Urbia Green is the ideal solution for all homes where the best performance is required. It is a concentration of advantages in terms of sanitary comfort with reduced dimensions and consumption. Thanks to condensing technology and integration with solar systems, it maximizes energy savings and the 4-litre sanitary reserve satisfies the needs of the most demanding users. Sanitary comforts Mini-accumulintegrated in 316L stainless steel of 4 liters. Domestic hot water performance ***, maximum level unexpected by the EN 13203 standard. Flow rate from 14.6 to 19.3 l/min with T = 25§C. DHW production controlled by a modulating turbine to respond to needs without waiting times and at a constant temperature, even when extractions are very low. DHW programmer to control the tank heating time slots Eco-Delta System: DHW load system with 4 liter reserve to further improve the comfort of DHW production and new ecological functions which allow you to save energy in DHW mode. Heating comfort Efficiencyfinal 108% with energy savingsfinal 35%. 4-star combustion efficiency according to the EN 92/42 standard. SRA function, automatic boiler regulation system according to heating requirements. Modulation wide range, from 10% to 100% of the maximum power. Reduced polluting emissions, NOx class 5. Pressure sensor of the heating circuit with visualization on LCD display. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the room and/or outside temperature. Arrangement for integration into a heating system via the newÿEbus2 communication protocolÿ(boilers, solar, system management modules, modulating thermoregulation accessories). Multifunction LCD display with display: history, self-diagnosis, operating temperature. Filling taps integrated in the boiler. Convenience of installation use Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier start-up: automatic purge function and directly accessible combustion adjustment. Save energy and respect the environment Final 25% energy savings in combination with Expert Control and the SRA function. Final 35% energy savings combine and Expert Control, the SRA function, the external probe and the radiant floor. 40% reduction in CO2 emissions**. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION CNG/LPG ADJUSTMENT THROUGH A SIMPLE PARAMETER. FOR FURTHER INFORMATION, CONTACT THE AREA AUTHORIZED SERVICE CENTER IN ADVANCE Sime VERA 30 HE condensing boiler Low NOx flue gas kit methane - New ErP Vera 30 HE model Heating energy efficiency class A Sanitary energy efficiency class A XL load profile Performance Nominal / minimum heat output (80-60°C) kW 23.7 / 4.5 Nominal heat input in heating kW 24 DHW nominal heat input kW 30 Useful efficiency 30% of the load (40-30°C) % 108.5 Heating sound power dB (A) 58 Electrical protection degree IP X5D Heating expansion vessel capacity l 9 Dimensions HxWxD 700x400x250 NOx class 6 VERA HE THE BOILER FOR EVERY TYPE OF SYSTEM Vera HE is the range of premixed wall-mounted condensing boilers that adapt to different system solutions. Thanks to the high head of the circulator, it is perfect for managing radiant floor systems without the use of booster pumps. The compact dimensions make it suitable for replacing existing fixtures and for outdoor or recessed installation using simple accessories. Vera HE features a new single-tube primary exchanger in stainless steel which boasts larger water passage sections compared to market standards, thus offering low pressure drops to the hydraulic system. The single-tube geometry guarantees higher water speeds, preventing deposits and encrustations and furthermore facilitating the cleaning of the exchanger. ACTIVE COMBUSTION CONTROL Vera HE is the range of premixed wall-mounted condensing boilers that adapt to different system solutions. Thanks to the high head of the circulator, it is perfect for managing radiant floor systems without the use of booster pumps. The compact dimensions make it suitable for replacing existing fixtures and for outdoor or recessed installation using simple accessories. Vera HE features a new single-tube primary exchanger in stainless steel which boasts larger water passage sections compared to market standards, thus offering low pressure drops to the hydraulic system. The single-tube geometry guarantees higher water speeds, preventing deposits and encrustations and furthermore facilitating the cleaning of the exchanger. The advanced control electronics check the combustion parameters at all times thanks to the flame sensor electrode and adjust the gas valve accordingly so as to always obtain the right air-gas ratio. The main advantages are: Simple commissioning, high reliability and low maintenance over time Compensation of combustion drifts caused by ageing, oxidation and insulation losses Ease of methane/LPG gas change using a simple parameter Guarantee of minimum polluting emissions guaranteed over time. Characteristics: Exchanger with oversized sections New heat exchanger with oversized water passage sections High head circulator Also suitable for radiant systems Active combustion control With electronic gas valve Three-piece shell For easier maintenance Can be installed externally or recessed Using special accessories or kits Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION IN THE ABSENCE OF THIS PRODUCT, THE MODEL PIGMA ADVANCE EXT 25 WILL BE SUPPLIED Overview CHAFFOTEAUX PIGMA GREEN EXT Ebus2 25 EU CONDENSING BOILER Cod. 3310443, COMPLETE WITH FUME KIT - NEW ErP 2015: Condensing technology with minimum bulk and maximum installation versatility make Pigma Green Ext Ebus2 EU the best choice where living spaces are you don't want to give up comfort and savings. Technical specifications Product code: 3310443 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Nominal heat input in heating max/min (Hi) Qn: 22/5.5 kW Useful heat output 80/60øC in heating/sanitary max/min:ÿ21.5/5.4kW Nominal heat input in sanitary(60/80øC) max/min:ÿ26/5,5 kW Efficiency at nominal heat input:ÿ97.5% Efficiency 30% of nominal heat input:ÿ109% Sanitary comfort performance starsEN13203: *** Energy efficiency stars: (dir 92/42/CEE) **** Capacity of the expansion vessel: 8 lt Port. specific in healthcare (10 min. with T= 30øC): 12.2 l/min Minimum withdrawal:ÿ<2ÿl/min Total absorbed electric power: 76 W Degrees of protection for the electrical system: IPÿX5D Dimensions hxwxd: mmÿ766x505x240ÿ; 32kg METHANE power supply or Features list PIGMA GREEN EXT Ebus2 EU Condensing technology with minimum bulk maximum installation versatility makes Pigma Green Ext Ebus2 EU the best choice where living spaces are precious and you don't want to give up comfort and savings. Resistant to corrosion, wind and frost, it can be installed anywhere and conveniently control all functions via the standard Expert Control system manager. Pigma Green Ext Ebus2 can be perfectly integrated with solar thermal systems and modules for the management of multi-zone systems, even with different temperatures, to make any design solution simple. Sanitary comfort Increased plate heat exchanger in stainless steel. 3-star sanitary comfort, the maximum unexpected by the EN 13203 standard. 12 l/min (T= 30°C) domestic hot water flow rate, measured in compliance with standard EN 625. Sanitary circuit managed by four probes and a flowmeter, to eliminate waiting times and have a constant temperature, even in the case of small withdrawals. Perfectly integrable with thermal solar systems, forced and natural circulation Daily and weekly hourly programming of the DHW exchanger pre-heating periods directly from the Expert Control system manager. Heating comfort ÿRendimentfinal 109% with energy savingsfinal 35%. 4-star combustion efficiency according to the EN 92/42 standard. Automatic regulation system, which can be activated directly from the Remote Control, to obtain the best heating operating regime in all environmental conditions. Useful thermal power up to 23.5 kW. Modulation ratio 1:5. Reduced polluting emissions, NOx class 5. Heating circuit pressure sensor with display on Expert Control. Modulating circulatorÿ to improve acoustic comfort and reduce electricity consumption. Differentiated climatic thermoregulation of 3 circuits, according to the ambient and external temperature. Operation management and programming through the Expert Control system manager: operating modes and temperatures, self-diagnosis, daily and weekly programming, adjustment information and history of the latest faults. Convenience of installation use Semi-automatic fillings that can be activated from the Expert Control system manager. Expert Control system manager and external probe as standard. Adjustment of operating parameters directly to Expert Control system manager. Arranged for the control of 3-circuit system management modules at different temperatures. Prepared for the management and integration of thermal solar systems (standard solar probe). Electrical protection degrees IPX5D and operation guaranteed up to -15øC **. Commissioning made easier: automatic de-aeration function and combustion regulation with direct access. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

RIELLO START CONDENS 25 KIS LPG CONDENSING BOILER COMPLETE WITH FUME KIT - NEW ErP General characteristics Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Heating rated heat output: 19.5 kW Sanitary nominal heat input: 25 kW Sanitary nominal thermal power: 25 kW Energy efficiency (92/42/EEC) **** Useful efficiency Pn (50°/30°): 104.2% Profit return 30% (47th return): 108.9% Sealed chamber, forced draught Quantity of hot water with Δt 25°C: 14.3 l/min Dimensions (hxwxd) mm 792 x 405 x 248 ; 30 Kgs Electrical protection degree: IP X5D NOx class: 5 Power supply: LPG Technical features START CONDENS Yield **** Low polluting emissions Aluminum condenser, with premix burner Combined models for indoor, outdoor, built-in, with stainless steel storage tank Start Condens is the new Riello condensing wall-mounted proposal for small and medium-sized domestic users. The new compact aluminum condensing exchanger guarantees efficiency and reduction of polluting emissions. It can also be installed outdoors in a partially protected place. It is available in version 25 (with 25 kW of DHW power and 20 kW in heating) and 29 (with 29 kW of DHW power and 25 kW in heating). Characteristics: Low consumption circulator (IEE≤0.20) "Winter with Pre-heating" function: allows the DHW exchanger to be kept at temperature, reducing waiting times during withdrawal (can be activated by the user) Standard thermoregulation on the card in combination with the external probe (optional) Assembly template, hydraulic fittings, power supply cable supplied Natural gas operation as standard with the possibility of conversion to LPG (G31) and propane air (accessories), this modification is the responsibility of the installer or the technical assistance service. Possibility of outdoor installation in partially protected places, using special accessory kits. Yield **** Low polluting emissions Aluminum condenser, with premix burner Combined models and heating only for indoors, outdoors in partially protected places ErP: Energy related Products The new European regulations for heat generators ErP is the acronym of “ Energy related Products ” (products connected to the use of energy) and is the abbreviation that identifies the European Directive ErP 2009/125/EC, defined by the EEC with the intention of reducing the energy consumption of products through eco-compatible design ("eco-design "). The field of action of this European Directive is extremely broad as up to now it has involved products such as light bulbs, air conditioners, washing machines, fans, etc. Following the publication in September 2013 of a series of implementing regulations, starting from 26 September 2015 it will also apply to heating products and the production of domestic hot water. From the same date, other regulations will also become effective which will implement the energy labeling of the same product families. The transitional period between the publication of the regulations and their activation throughout the territory of the European Community was necessary to allow the full implementation of the contents by companies and market players.   The energy labeling of products for heating and domestic hot water production The regulations issued require that all products intended for heating and/or for the production of domestic hot water, with a nominal thermal power lower than or equal to 70 kW, are placed on the market with an energy label that highlights their efficiency class. Note: the regulation provides for the mandatory presence of the energy label for the release of the product from the factories to the market. All products previously introduced, for example present in distribution warehouses, can be regularly marketed even if they do not have an energy label. Various energy labels have been provided based on the use of the generator used: for heating from A++ to G; for the production of domestic hot water from A to G.   A new way to guide the consumer The purpose of energy labels is to allow the consumer to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pump products, as has been done for air conditioners, the efficiency figure is reported for the average climatic range. In addition to the product energy labels, the European regulations have also provided for the creation of a system label in the event that a plant is created in which various appliances, components and controls operate. This labelling, thanks to the combinations of the data of the various elements used in the plant, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual generators. The European regulation states that the system label must be made available by whoever supplies and/or puts the system into operation (sellers-installers); however, this option is also granted to builders. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less