ATTENTION THE PRODUCT IS NEW AND CHECKED BY OUR TECHNICIANS, IT HAS TRANSPORT DEFECTS: DEMORS AND DENTS ON THE MAIN PANEL WORN PACKAGING (FOR MORE DETAILS VIEW THE PHOTOS NEXT TO THE MAIN IMAGE). Beretta Idrabagno LX 11 lt LPG Gas Water Heater Complete with Low NOx Smoke Kit METHANE Code: 20143031 GPL Code: 20143032 Energy label specifications according to European ErP directive Energy efficiency of health care: Class A Load profile: M Health energy efficiency (ηwh) % 75.4 Daily gas consumption (Qfuel) kW/h 8,109 Annual gas consumption (AFC) GJ 6 Daily electricity consumption (Qelec) kWh 0.065 Annual electricity consumption (AEC) kWh 14 Sound power level indoors (LWA) dB(A) 51 Nitrogen oxide emissions (Nox) mg/kWh 33 Characteristics Type - sealed chamber Draught - forced draft Ignition - ion (electric) Flame control - ionization Flame modulation - electronic Hot water flow rate Δt=30°C litres/min 9.5 Nominal heat output (G20-G30-G31) kW 22.20 Nominal thermal power (G20-G30-G31) kW 19.89 Waterfall Sanitary water temperature selection range °C 36 - 65 Minimum / nominal / maximum pressure bar 0.2 / 2 / 10 Water connections Ø 1/2" Gas Nominal methane supply pressure (G20) mbar 20 Nominal supply pressure LPG (G30/G31) mbar 28-30 Gas connection Ø 3/4" 3/4" 3/4” Fume temperature (max-min) G20 / G30 / G31 °C 120-71 / 121-64 / 124-60 Electrical values Power consumption W 41 Supply voltage V/Hz 230/50 Electrical protection degree - IPX4D Dimensions and weight Dimensions (H×W×D) mm 642×340×237 Net weight 19 kg IDRABAGNO LX: INNOVATION IS AT HOME The new line of LOW NOx indoor water heaters From Beretta's technological research comes IDRABAGNO Lx, the new line of instantaneous water heaters with very low emissions , completely renewed in design, both aesthetic and functional, able to offer maximum sanitary comfort in compliance with recent European regulations on NOx. The wide range of IDRABAGNO Lx, consisting of 3 sealed chamber models of 11, 13 and 17 lt, with both methane and LPG codes, thanks to the new, elegant and linear aesthetics and compact dimensions, integrates perfectly into any living context, representing the ideal solution to meet every need for the production of domestic hot water. Ideal for installation inside the home, the new water heaters, in the 11 and 13 litre versions, can also be installed outside , in a partially protected place, with the addition of the antifreeze kit (available as an accessory) up to a temperature of -10°C for the 11 and 13 litre models, and -7°C for the 17 litre model. The new IDRABAGNO Lx line is able to satisfy the most demanding requirements in terms of low emissions that will come into force from September 2018 as required by Regulation (EU) 814/2013 which requires nitrogen oxide emissions equal to or lower than 56 mg/kWh. Thanks to the innovative Idrabagno Lx burner, of the hyperstoichiometric type, the flame is fed by an air-gas mixture in excess of that required for combustion, resulting in a very low flame temperature. This feature, combined with the cooling of the burner through the water in the water heater circuit, results in a significant reduction in the polluting values ​​of carbon monoxide and nitrogen produced by combustion, such as to fully satisfy the new limits imposed by international regulations. The high thermal capacity, together with the wide flame modulation (up to 45% of the nominal capacity) complete the profile of the new burner in terms of performance, offering the user maximum sanitary comfort. Lots of new features Simple and intuitive interface with icon language Large backlit display and 4 control buttons Special functions and self-diagnostics on display Latest generation burner Water-cooled hyperstoichiometric burner Wide flame modulation High thermal capacity, maximum sanitary comfort Product Warranty All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENZIONE IL PRODOTTO È NUOVO E CONTROLLATO DAI NOSTRI TECNICI, PRESENTA DIFETTI DA TRASPORTO: AMMACCATURA SUL LATERALE DESTRO IMBALLO USURATO (PER MAGGIORI DETTAGLI VISUALIZZA LE FOTO ACCANTO ALL'IMMAGINE PRINCIPALE). Scaldabagno a Gas Beretta Idrabagno LX 11 lt Gpl Completo di Kit Fumi Low NOx - New ErP Codice METANO: 20143031 Codice GPL: 20143032 Specifiche etichetta energetica secondo direttiva Europea ErP Efficienza energetica sanitario: Classe A Profilo di carico: M Efficienza energetica sanitario (ηwh) % 75,4  Consumo giornaliero di gas (Qfuel) kW/h 8,109  Consumo annuo di gas (AFC) GJ 6  Consumo giornaliero di energia elettrica (Qelec) kWh 0,065  Consumo annuo di energia elettrica (AEC) kWh 14  Livello della potenza sonora all'interno (LWA) dB(A) 51 Emissioni di ossidi di Azoto (Nox) mg/kWh 33  Caratteristiche Tipologia - camera stagna  Tiraggio - tiraggio forzato  Accensione - iono (elettrica) Controllo di fiamma - a ionizzazione Modulazione di fiamma - elettronica  Portata acqua calda Δt=30°C litri/min 9,5  Portata termica nominale (G20-G30-G31) kW 22,20  Potenza termica nominale (G20-G30-G31) kW 19,89  Acqua Campo di selezione temperatura acqua sanitario °C 36 - 65  Pressione minima / nominale / massima bar 0,2 / 2 / 10  Attacchi acqua Ø 1/2"  Gas Pressione nominale di alimentazione a metano (G20) mbar 20  Pressione nominale di alimentazione GPL (G30/G31) mbar 28-30 Attacco gas Ø 3/4" 3/4" 3/4” Temperatura fumi (max-min) G20 / G30 / G31 °C 120-71 / 121-64 / 124-60 Valori elettrici Potenza assorbita W 41  Tensione di alimentazione V/Hz 230/50 Grado di protezione elettrica - IPX4D Dimensioni e peso Dimensioni (H×L×P) mm 642×340×237 Peso netto kg 19  IDRABAGNO LX: L’INNOVAZIONE È DI CASA   La nuova linea di scaldabagni LOW NOx da interno Dalla ricerca tecnologica di Beretta nasce IDRABAGNO Lx, la nuova linea di scaldabagni istantanei a bassissime emissioni, completamente rinnovata nel design, sia estetico che funzionale, in grado di offrire il massimo comfort sanitario nel rispetto delle recenti normative Europee in tema di NOx.L’ampia gamma di IDRABAGNO Lx, costituita da 3 modelli a camera stagna di 11, 13 e 17 lt, con codici sia a metano che a GPL, grazie alla nuova estetica, elegante e lineare, e alle dimensioni compatte, si integra perfettamente in ogni contesto abitativo, rappresentando la soluzione ideale per rispondere ad ogni esigenza di produzione di acqua calda sanitaria ad uso domestico.Ideali per l’installazione all’interno dell’abitazione, i nuovi scaldabagni, nelle versioni 11 e 13 lt, possono essere installati anche all’esterno, in luogo parzialmente protetto, con l’aggiunta del kit antigelo (disponibile come accessorio) fino ad una temperatura di -10°C per i modelli 11 e 13 litri, e -7°C per il modello 17 lt. La nuova linea IDRABAGNO Lx è in grado di soddisfare i più esigenti requisiti in termini di basse emissioni che entreranno in vigore da settembre 2018 come previsto dal Regolamento (UE) 814/2013 che richiede emissioni di ossidi di azoto uguali o inferiori a 56 mg/kWh. Grazie all’innovativo bruciatore di Idrabagno Lx, di tipo iperstechiometrico, la fiamma viene alimentata da una miscela aria-gas in eccesso rispetto a quella necessaria per la combustione, ottenendo come effetto una temperatura di fiamma molto bassa.Da questa caratteristica, in combinazione col raffreddamento del bruciatore attraverso l’acqua del circuito dello scaldabagno, deriva un abbassamento sensibile dei valori inquinanti di ossido di carbonio e di azoto prodotti dalla combustione, tali da soddisfare a pieni voti i nuovi limiti imposti dalla normativa internazionale.L’elevata portata termica, unitamente all’ampia modulazione di fiamma (fino al 45% della portata nominale) completano il profilo del nuovo bruciatore in termini di performance, offrendo all’utente il massimo comfort sanitario. Tante nuove funzioni Interfaccia semplice e intuitiva con liguaggio a icone Ampio display retroilluminato e 4 tasti comando Funzioni speciali e autodiagnostica a display Bruciatore di ultima generazione Bruciatore iperstechiometrico raffreddato ad acqua Ampia modulazione di fiamma Elevata portata termica, massimo comfort sanitario Garanzia ProdottoTutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.

Read more less

Technical features Energy label specifications according to the European ErP directive   Sanitary Energy Efficiency : Class A Load profile: M Exercise features: Open chamber with natural draft Ignition - 1.5 battery Flame control - by ionization Rated thermal power: 19kW Hot water production Δ T=25°C: 11 l/min Min/max pressure bar 0.3/10 Ø water and gas connections - 1/2” Dimensions (HxLxP): mm 580 x 310 x 215; 9.5 kgs The guarantee is the Official Beretta Italia one, and has a duration of 24 months Power supply: METHANE General characteristics SOURCE 2 DGT Fonte 2 DGT, hot water in compact dimensions From Beretta's experience and technological research comes the new line of Fonte 2 DGT water heaters, designed to offer maximum sanitary comfort, maximum energy savings and greater simplicity of use. Thanks to its extremely compact dimensions, Fonte 2 DGT can also be placed in limited spaces and therefore represents the ideal solution to meet the installation needs of modern living contexts. The range, open ionization chamber with battery ignition, two water filters as standard and with codes for both methane and LPG, is made up of the Fonte 2 DGT versions with 11 and 14 litres/min models and Fonte 2 DGT FLEX with a from 11 litres/min. The FLEX versions also include the hoses and the sanitary tap. Source 2 DGT: high energy class and low consumption The Fonte 2 DGT line of water heaters is equipped with the special device known as the Economiser, specifically designed to combine maximum user comfort with significant energy and cost savings. The activation of the Economizer in fact allows to reduce the gas consumption up to over 50%, limiting the maximum thermal power supplied, when the usage requirements are contained (low temperature difference or reduced sampling flow rates, such as for example during summertime). Furthermore, on all Fonte 2 DGT models, the Economizer can be adjusted progressively by the user, according to needs, achieving maximum savings in the low flame position. Finally, the appliances in the Fonte 2 DGT range are equipped with flame modulation which, by adapting gas consumption to individual withdrawal requests, allows the temperature of the water supplied to be kept almost constant, compatibly with the settings made and the power of the water heater. The Beretta Fonte 2 DGT water heater guarantees always very low gas consumption and respect for the environment. Beretta Fonte 2 DGT complies with the current ERP regulation placing itself in CLASS A for energy consumption. Functionality and ease of use The Fonte 2 DGT water heaters, with a linear and essential design, have an ergonomic dashboard which houses two knobs which allow you to manage all the functions of the appliance in a simple and intuitive way and a display which shows the temperature of the domestic hot water produced. The left knob, in addition to the on/off functions, activates the "Gas economizer" device, which can be adjusted between the small flame and the large flame, allowing the user to make interesting gas savings. The right knob allows you to set the temperature of the water supplied, by regulating the quantity of water at the outlet Characteristics: Instantaneous open chamber water heater with Natural Gas and LPG versions Abundant production of domestic hot water: 11 or 14 litres/min Digital display with indication of domestic hot water temperature Battery ignition and ionisation flame presence control Gas economizer with 8 regulation steps Modulating flame regulation system Simple and intuitive control panel Compact size and simple installation without removing the shell Assembly template supplied (gasket and hose holder for LPG versions) New easy access water connections on the same horizontal axis New latest generation water/gas group with integrated gas pressure regulator Double inlet water filter Safety microswitch to protect the batteries (2 x 1.5 Volt type D) in the OFF position Temperature selector FLEX versions with flexible fittings and standard tap Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations simultaneously issued for the energy labeling of products will also become effective in addition to the corresponding Directive 2010/30/EU. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with a nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Beretta open chamber water heater mod. FONTE LX 14 lt Low NOx LPG - NEW ErP ENERGY LABEL SPECIFICATIONS ACCORDING TO EUROPEAN ErP DIRECTIVE Sanitary energy efficiency Class A Sanitary load profile - M Characteristics Typology - Open chamber Draft - Natural draft Ignition - 2 x 1.5V batteries Flame control - by ionization Flame modulation - continued Hot water production ∆t=30° litres/min 11.6 Nominal heat input (G20 / G30-G31) kW 28.0 / 28.0 Rated thermal power (G20 / G30-G31) kW 24.36 / 24.75 Waterfall Withdrawal range - Idle selector litres/min from 2.5 to 6.5 Withdrawal range - Selector at maximum litres/min from 2.5 to 14 Water temperature elevation - Selector at minimum °C 50 Water temperature elevation - Selector at maximum 25 °C Minimum / normal / maximum pressure bar 0.2 / 2 / 10 Ø water connections - 1/2” DHW temperature selection range °C 35-60 Gas Nominal gas supply pressure (G20) mbar 20 Ø gas connection - 1/2” Dimensions and weight Dimensions (HxWxD) mm 675x350x230; 12Kg SOURCE LX new Low NOx open chamber water heater Within the new generation of low NOx emission products, Beretta presents Fonte Lx, the new instantaneous open chamber water heater, entirely Beretta signature both for know-how and for industrialization. The new Fonte Lx range, completely renewed in terms of aesthetics and planning, consists of two models, 11 and 14 liters respectively, available in both methane and LPG versions, with dedicated codes, able to offer maximum sanitary comfort in compliance with recent European regulations for the reduction of NOx emissions. The compactness and modernity of the design allow Fonte Lx to be easily placed in any living context, characteristics which, together with the simplicity of maintenance and use for the end user, distinguish Fonte Lx as a very appreciable product in the panorama of residential comfort. Modern and intuitive control panel Fonte Lx stands out for its ease of use for the end user, a feature that reconfirms one of the drivers of Beretta's technological research since its origins, aimed at creating products with maximum usability. The design of the new panel, modern and linear, in line with the new generation Beretta products, is characterized by an intuitive, backlit display, which immediately displays the water temperature in °C and the diagnostics of any anomalies, together with two icons indicating the presence of a flame and the battery charge level. Three command keys allow the end user to manage all the functions of the water heater. On the panel there is also a led that flashes when the battery level is low, thus signaling the need for their replacement. Characteristics Instantaneous open chamber water heater with dedicated methane and LPG versions Battery ignition (2 x 1.5V batteries supplied as standard) High sanitary load profile (XL on the 14 lt model) Abundant production of domestic hot water at Δt 25°C of 11 and 14 litres/min Innovative project design New self-adapting system with thermostatic device Increased modulation of power and domestic hot water flow, compared to the previous range Electronic reset from the user interface of the water and smoke thermostats, in the event of anomalies (RESET key) New Design Innovative interface with backlit display, 3 control keys and battery replacement LED Modern aesthetics and compact dimensions for an easy setting in any living context Ease of use Simple and intuitive command keys Immediate visualization of the temperature on the display Battery charge level shown on display with LED to signal replacement High comfort Wide picking range and comfort High stability of the temperature of the hot water supplied Delivery of domestic hot water even with minimum withdrawals or low pressure Less consumption Thanks to the advanced electronic modulating flame regulation system Easy to install and maintain Quick and easy installation with no need to remove the casing Innovative electronic gas valve without membrane for zero-time maintenance Latest generation low NOx burner The new FONTE Lx line is able to satisfy the most demanding requirements in terms of low emissions in force since September 2018, as required by Regulation (EU) 814/2013 which requires emissions of nitrogen oxides equal to or lower than 56 mg/kWh . Thanks to the innovative FONTE Lx burner of the hyperstoichiometric type, cooled by water, a significant lowering of the polluting values ​​of carbon monoxide and nitrogen produced by combustion is obtained, such as to satisfy the new limits of international legislation with full marks. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

Beretta open chamber water heater mod. FONTE LX 14 lt Low NOx Methane cod. 20149825 - NEW ErP ENERGY LABEL SPECIFICATIONS ACCORDING TO EUROPEAN ErP DIRECTIVE Sanitary energy efficiency Class A Sanitary load profile - M Characteristics Typology - Open chamber Draft - Natural draft Ignition - 2 x 1.5V batteries Flame control - by ionization Flame modulation - continued Hot water production ∆t=30° litres/min 11.6 Nominal heat input (G20 / G30-G31) kW 28.0 / 28.0 Rated thermal power (G20 / G30-G31) kW 24.36 / 24.75 Waterfall Withdrawal range - Idle selector litres/min from 2.5 to 6.5 Withdrawal range - Selector at maximum litres/min from 2.5 to 14 Water temperature elevation - Selector at minimum °C 50 Water temperature elevation - Selector at maximum 25 °C Minimum / normal / maximum pressure bar 0.2 / 2 / 10 Ø water connections - 1/2” DHW temperature selection range °C 35-60 Gas Nominal gas supply pressure (G20) mbar 20 Ø gas connection - 1/2” Dimensions and weight Dimensions (HxWxD) mm 675x400x230; 12Kg SOURCE LX new Low NOx open chamber water heater Within the new generation of low NOx emission products, Beretta presents Fonte Lx, the new instantaneous open chamber water heater, entirely Beretta signature both for know-how and for industrialization. The new Fonte Lx range, completely renewed in terms of aesthetics and planning, consists of two models, 11 and 14 liters respectively, available in both methane and LPG versions, with dedicated codes, able to offer maximum sanitary comfort in compliance with recent European regulations for the reduction of NOx emissions. The compactness and modernity of the design allow Fonte Lx to be easily placed in any living context, characteristics which, together with the simplicity of maintenance and use for the end user, distinguish Fonte Lx as a very appreciable product in the panorama of residential comfort. Modern and intuitive control panel Fonte Lx stands out for its ease of use for the end user, a feature that reconfirms one of the drivers of Beretta's technological research since its origins, aimed at creating products with maximum usability. The design of the new panel, modern and linear, in line with the new generation Beretta products, is characterized by an intuitive, backlit display, which immediately displays the water temperature in °C and the diagnostics of any anomalies, together with two icons indicating the presence of a flame and the battery charge level. Three command keys allow the end user to manage all the functions of the water heater. On the panel there is also a led that flashes when the battery level is low, thus signaling the need for their replacement. Characteristics Instantaneous open chamber water heater with dedicated methane and LPG versions Battery ignition (2 x 1.5V batteries supplied as standard) High sanitary load profile (XL on the 14 lt model) Abundant production of domestic hot water at Δt 25°C of 11 and 14 litres/min Innovative project design New self-adapting system with thermostatic device Increased modulation of power and domestic hot water flow, compared to the previous range Electronic reset from the user interface of the water and smoke thermostats, in the event of anomalies (RESET key) New Design Innovative interface with backlit display, 3 control keys and battery replacement LED Modern aesthetics and compact dimensions for an easy setting in any living environment Ease of use Simple and intuitive command keys Immediate visualization of the temperature on the display Battery charge level shown on display with LED to signal replacement High comfort Wide picking range and comfort High stability of the temperature of the hot water supplied Delivery of domestic hot water even with minimum withdrawals or low pressure Less consumption Thanks to the advanced electronic modulating flame regulation system Easy to install and maintain Quick and easy installation with no need to remove the casing Innovative electronic gas valve without membrane for zero-time maintenance Latest generation low NOx burner The new FONTE Lx line is able to satisfy the most demanding requirements in terms of low emissions in force since September 2018, as required by Regulation (EU) 814/2013 which requires emissions of nitrogen oxides equal to or lower than 56 mg/kWh . Thanks to the innovative FONTE Lx burner of the hyperstoichiometric type, cooled by water, a significant lowering of the polluting values ​​of carbon monoxide and nitrogen produced by combustion is obtained, such as to satisfy the new limits of international legislation with full marks. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

Technical features Energy label specifications according to the European ErP directive   Sanitary Energy Efficiency : Class A Load profile: L Exercise features: Open chamber with natural draft Ignition - 1.5 battery Flame control - by ionization Nominal heat output: 24 kW Hot water production Δ T=25°C: 14 l/min Min/max pressure bar 0.3/10 Ø water and gas connections - 1/2” Dimensions (HxLxP): mm 620x380x224; 11.5 kgs The guarantee is the Official Beretta Italia one, and has a duration of 24 months Power supply: LPG General characteristics SOURCE 2 DGT Fonte 2 DGT, hot water in compact dimensions From Beretta's experience and technological research comes the new line of Fonte 2 DGT water heaters, designed to offer maximum sanitary comfort, maximum energy savings and greater simplicity of use. Thanks to its extremely compact dimensions, Fonte 2 DGT can also be placed in limited spaces and therefore represents the ideal solution to meet the installation needs of modern living contexts. The range, open ionization chamber with battery ignition, two water filters as standard and with codes for both methane and LPG, is made up of the Fonte 2 DGT versions with 11 and 14 litres/min models and Fonte 2 DGT FLEX with a from 11 litres/min. The FLEX versions also include the hoses and the sanitary tap. Source 2 DGT: high energy class and low consumption The Fonte 2 DGT line of water heaters is equipped with the special device known as the Economiser, specifically designed to combine maximum user comfort with significant energy and cost savings. The activation of the Economizer in fact allows to reduce gas consumption up to over 50%, limiting the maximum thermal power supplied, when the usage requirements are contained (low temperature difference or reduced sampling flow rates, such as for example during summertime). Furthermore, on all Fonte 2 DGT models, the Economizer can be adjusted progressively by the user, according to needs, achieving maximum savings in the low flame position. Finally, the appliances in the Fonte 2 DGT range are equipped with flame modulation which, by adapting gas consumption to individual withdrawal requests, allows the temperature of the water supplied to be kept almost constant, compatibly with the settings made and the power of the water heater. The Beretta Fonte 2 DGT water heater guarantees always very low gas consumption and respect for the environment. Beretta Fonte 2 DGT complies with the current ERP regulation placing itself in CLASS A for energy consumption. Functionality and ease of use The Fonte 2 DGT water heaters, with a linear and essential design, have an ergonomic dashboard which houses two knobs which allow you to manage all the functions of the appliance in a simple and intuitive way and a display which shows the temperature of the domestic hot water produced. The left knob, in addition to the on/off functions, activates the "Gas economiser" device, adjustable between the small flame and the large flame, allowing the user to make an interesting gas saving. The right knob allows you to set the temperature of the water supplied, by regulating the quantity of water at the outlet Characteristics: Instantaneous open chamber water heater with Natural Gas and LPG versions Abundant production of domestic hot water: 11 or 14 litres/min Digital display with indication of domestic hot water temperature Battery ignition and ionisation flame presence control Gas economizer with 8 regulation steps Modulating flame regulation system Simple and intuitive control panel Compact size and simple installation without removing the shell Assembly template supplied (gasket and hose holder for LPG versions) New easy access water connections on the same horizontal axis New latest generation water/gas group with integrated gas pressure regulator Double inlet water filter Safety microswitch to protect the batteries (2 x 1.5 Volt type D) in the OFF position Temperature selector FLEX versions with flexible fittings and standard tap Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Energy label specifications according to the European ErP directive   Sanitary Energy Efficiency : Class A Load profile: M Exercise features: Open chamber with natural draft Ignition - 1.5 battery Flame control - by ionization Rated thermal power: 19kW Hot water production Δ T=25°C: 11 l/min Min/max pressure bar 0.3/10 Ø water and gas connections - 1/2” Dimensions (HxLxP): mm 580 x 310 x 215; 9.5 kgs The guarantee is the Official Beretta Italia one, and has a duration of 24 months Power supply: LPG General characteristics SOURCE 2 DGT Fonte 2 DGT, hot water in compact dimensions From Beretta's experience and technological research comes the new line of Fonte 2 DGT water heaters, designed to offer maximum sanitary comfort, maximum energy savings and greater ease of use. Thanks to its extremely compact dimensions, Fonte 2 DGT can also be placed in limited spaces and therefore represents the ideal solution to meet the installation needs of modern living contexts. The range, open ionization chamber with battery ignition, two water filters as standard and with codes for both methane and LPG, is made up of the Fonte 2 DGT versions with 11 and 14 litres/min models and Fonte 2 DGT FLEX with a from 11 litres/min. The FLEX versions also include the hoses and the sanitary tap. Source 2 DGT: high energy class and low consumption The Fonte 2 DGT line of water heaters is equipped with the special device known as the Economiser, specifically designed to combine maximum user comfort with significant energy and cost savings. The activation of the Economiser in fact allows to reduce the gas consumption up to over 50%, limiting the maximum thermal power supplied, when the usage requirements are contained (low temperature difference or reduced sampling flow rates, such as for example during summertime). Furthermore, on all Fonte 2 DGT models, the Economizer can be adjusted progressively by the user, according to needs, achieving maximum savings in the low flame position. Finally, the appliances in the Fonte 2 DGT range are equipped with flame modulation which, by adapting gas consumption to individual withdrawal requests, allows the temperature of the water supplied to be kept almost constant, compatibly with the settings made and the power of the water heater. The Beretta Fonte 2 DGT water heater guarantees always very low gas consumption and respect for the environment. Beretta Fonte 2 DGT complies with the current ERP regulation placing itself in CLASS A for energy consumption. Functionality and ease of use The Fonte 2 DGT water heaters, with a linear and essential design, have an ergonomic dashboard which houses two knobs which allow you to manage all the functions of the appliance in a simple and intuitive way and a display which shows the temperature of the domestic hot water produced. The left knob, in addition to the on/off functions, activates the "Gas economiser" device, adjustable between the small flame and the large flame, allowing the user to make an interesting gas saving. The right knob allows you to set the temperature of the water supplied, by regulating the quantity of water at the outlet Characteristics: Instantaneous open chamber water heater with Natural Gas and LPG versions Abundant production of domestic hot water: 11 or 14 litres/min Digital display with indication of domestic hot water temperature Battery ignition and ionisation flame presence control Gas economizer with 8 regulation steps Modulating flame regulation system Simple and intuitive control panel Compact size and simple installation without removing the shell Assembly template supplied (gasket and hose holder for LPG versions) New easy access water connections on the same horizontal axis New latest generation water/gas group with integrated gas pressure regulator Double inlet water filter Safety microswitch to protect the batteries (2 x 1.5 Volt type D) in the OFF position Temperature selector FLEX versions with flexible fittings and standard tap Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Energy label specifications according to the European ErP directive   Sanitary Energy Efficiency : Class A Load profile: L Exercise features: Open chamber with natural draft Ignition - 1.5 battery Flame control - by ionization Nominal heat output: 24 kW Hot water production Δ T=25°C: 14 l/min Min/max pressure bar 0.3/10 Ø water and gas connections - 1/2” Dimensions (HxLxP): mm 620x380x224; 11.5 kgs The guarantee is the Official Beretta Italia one, and has a duration of 24 months Power supply: METHANE General characteristics SOURCE 2 DGT Fonte 2 DGT, hot water in compact dimensions From Beretta's experience and technological research comes the new line of Fonte 2 DGT water heaters, designed to offer maximum sanitary comfort, maximum energy savings and greater simplicity of use. Thanks to its extremely compact dimensions, Fonte 2 DGT can also be placed in limited spaces and therefore represents the ideal solution to meet the installation needs of modern living contexts. The range, open ionization chamber with battery ignition, two water filters as standard and with codes for both methane and LPG, is made up of the Fonte 2 DGT versions with 11 and 14 litres/min models and Fonte 2 DGT FLEX with a from 11 litres/min. The FLEX versions also include the hoses and the sanitary tap. Source 2 DGT: high energy class and low consumption The Fonte 2 DGT line of water heaters is equipped with the special device known as the Economizer, specifically designed to combine maximum user comfort with significant energy and cost savings. The activation of the Economiser in fact allows to reduce the gas consumption up to over 50%, limiting the maximum thermal power supplied, when the usage requirements are contained (low temperature difference or reduced sampling flow rates, such as for example during summertime). Furthermore, on all Fonte 2 DGT models, the Economizer can be adjusted progressively by the user, according to needs, achieving maximum savings in the low flame position. Finally, the appliances in the Fonte 2 DGT range are equipped with flame modulation which, by adapting gas consumption to individual withdrawal requests, allows the temperature of the water supplied to be kept almost constant, compatibly with the settings made and the power of the water heater. The Beretta Fonte 2 DGT water heater guarantees always very low gas consumption and respect for the environment. Beretta Fonte 2 DGT complies with the current ERP regulation placing itself in CLASS A for energy consumption. Functionality and ease of use The Fonte 2 DGT water heaters, with a linear and essential design, have an ergonomic dashboard which houses two knobs which allow you to manage all the functions of the appliance in a simple and intuitive way and a display which shows the temperature of the domestic hot water produced. The left knob, in addition to the on/off functions, activates the "Gas economizer" device, which can be adjusted between the small flame and the large flame, allowing the user to make interesting gas savings. The right knob allows you to set the temperature of the water supplied, by regulating the quantity of water at the outlet Characteristics: Instantaneous open chamber water heater with Natural Gas and LPG versions Abundant production of domestic hot water: 11 or 14 litres/min Digital display with indication of domestic hot water temperature Battery ignition and ionisation flame presence control Gas economizer with 8 regulation steps Modulating flame regulation system Simple and intuitive control panel Compact size and simple installation without removing the shell Assembly template supplied (gasket and hose holder for LPG versions) New easy access water connections on the same horizontal axis New latest generation water/gas group with integrated gas pressure regulator Double inlet water filter Safety microswitch to protect the batteries (2 x 1.5 Volt type D) in the OFF position Temperature selector FLEX versions with flexible fittings and standard tap Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations simultaneously issued for the energy labeling of products will also become effective in addition to the corresponding Directive 2010/30/EU. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less