JUNKERS BOSCH GAS WATER HEATER MODEL THERM 4600 SO 12 LITERS LPG Product data for energy consumption - according to requirements of EU regulations no. 811/2013 and 812/2013 to complete the directive 2010/30/EU CNG code: T4600 SO 12-23 Water heating energy efficiency class A Declared load profile M External installation Remote control standard standard standard Forced draught sealed chamber Nominal heat output (Pn) [kW] 20.8 Nominal heat input (Qn) [kW] 22.5 Power setting/modulation range (Pn,min. - Pn,max.) [kW] 2.9-20 Flow rate of water supplied with ΔT 25 °C [l/min] 12 Flow rate of water supplied with ΔT 35 °C [l/min] 9 Efficiency at 100% of rated power [%] 92 sound pressure max. [dB(A)] 72 Power supply [V(AC)] 230 Maximum absorbed power [W] 228 Degree of electrical protection [IP] IPX5D Weight (without packaging) [kg] 10 Dimensions (H x W x D) [mm] 568 x 300 x 170 THERM 4600 SO THERM 4600 SO is the outdoor water heater with extremely compact dimensions. It satisfies any space and installation requirement, does not require fume extraction/exhaust systems, is resistant to cold and bad weather thanks to the antifreeze device (up to -25 °C). Furthermore, it is installed outside but can be easily managed from inside the home, in an easy and intuitive way, thanks to the large remote control display (standard). Advantages ▶ It is installed outdoors and does not require fume extraction and exhaust systems ▶ Resists the cold and bad weather thanks to the standard antifreeze device ▶ It is supplied with the remote control with display for managing the operating temperature, easy and intuitive ▶ It can be connected directly to solar thermal systems for the production of domestic hot water Characteristics ▶ Instant gas water heater with sealed chamber and forced draught for outdoor use, available in the 12, 15 and 18 l/min versions; methane and LPG ▶ Flame ionisation electronic ignition ▶ High efficiency and wide modulation range (1:7) ▶ Works even in case of very low water pressures ▶ Extremely compact dimensions Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

JUNKERS BOSCH THERM 6000i S WTD12-2 METHANE gas WATER HEATER WITH FUME KIT Water heating energy efficiency class A Nitrous oxide emissions (for gas and fuel oil only) NOx mg/kWh 127 Sound power level within LWA dB 63 Declared load profile M Other load profiles S Daily electricity consumption (average climatic conditions) Qelec kWh 0.096 Annual electricity consumption AEC kWh 21 Annual electricity consumption (other load profiles, average climate conditions) AEC kWh 25 Water heating energy efficiency ηwh % 69 Water heating energy efficiency (other load profiles) ηwh % 66 Daily fuel consumption Qfuel kWh 8,885 Annual fuel consumption AFC GJ 6 Annual fuel consumption (other load profiles) AFC GJ 2 THERM 6000i Refined design thanks to the front in tempered titanium glass and the soft touch display Water heater controlled via smart device through the Bosch Water App Optimized performance, it guarantees savings of up to 60 liters of water and up to 35% of gas Degree-by-degree temperature control for high-level comfort Refined design, touch display The Therm 6000i S water heater stands out for its modern and refined design. It comes with an elegant front in tempered titanium glass, available in black or white, and an integrated digital display with soft touch control. Thanks also to its small size, it is ideal for enriching your home with an innovative design element Saving up to 60 liters of water The degree-by-degree temperature regulation allows the Therm 6000i S water heater to have an optimized efficiency, thus guaranteeing savings of up to 60 liters of water and up to 35% of gas. These savings are favored by the Smart Hydraulics valve which allows the temperature to be reached quickly and increases its stability Bosch Water app The Therm 6000i S water heater can also be controlled with the dedicated Bosch Water app from iOS and Android smart devices (smartphones and tablets) via Bluetooth. The App allows numerous functions in addition to water temperature control, including the history of the last five consumptions and diagnostics in case of malfunctions High level comfort The comfort created by the Therm 6000i S water heater is maximum. Thanks to a patented algorithm, OptiFlow, optimal efficiency of the water heater is possible in all operating conditions and the minimum power used decreases, avoiding the risk of condensation forming on the heat exchanger. Product Guarantee: All products for sale on our site are new and im

Read more less

Overview GAS WATER HEATER JUNKERS HYDROCOMPACT INDOOR WTD 12 AM E (12 LT) LPG 2 - Forced draft sealed chamber water heaters COMPLETE WITH FUME EXHAUST KIT: Junkers Hydrocompact Indoor is the smallest instantaneous gas water heater available on the market. IN THE ABSENCE OF THE PRODUCT, THE NEW LPG THERM 5600 S 12 MODEL WILL BE SUPPLIED Technical specifications DHW energy efficiency class (ErP): A Catalog code: WTD 12 AM E Profile of charge declared: M Gas instantaneous water heater 2 - Forced draft sealed chamber water heaters Flame ionisation electronic ignition Nominal heat output: 20.8 kW Nominal heat input: 22.5 kW Efficiency at 100% of rated power: 92% Efficiency at 30% of rated power: 94% Water flow rate supplied with DT 25 C: 12 l/min Minimum operating flow: 2 l/min Maximum working pressure: 12 bar Minimum operating temperature with antifreeze kit: -25 C (accessory) Remote control: accessory Display: LCD multifunction degree of protection: IPX4D Dimensions (LxWxH): mm 170x300x568 Version: LPG Features list Hydrocompact Indoor: Compact gas instantaneous water heaters for indoor use You have little space available but you don't want to give up on quality and comfort as always It's natHYDROCOMPACTINDOOR, the new compact water heater in the Junkers range: all the usual comfort in very little space! The most compact ever HYDROCOMPACT INDOOR is the smallest indoor water heater available on the market. All Junkers quality and high technology are enclosed in just 17 cm depth (12 and 15 l/min models)! Easily placed inside a wall unit in your kitchen (in compliance with current regulations), the new HYDROCOMPACT INDOOR represents the best solution for those with space problems: thanks to its extremely compact dimensions, in fact, it is able to satisfy any need for space and installation. The simplicity of great technology Thanks to the new patented Junkers Optiflow technology, HYDROCOMPACTINDOOR is able to automatically recognize the lengths of the suction and flue gas system. This intelligent system helps to increase the efficiency of the product, improving its performance and reducing consumption. The large display integrated in the appliance also allows you to manage and program the operation with extreme simplicity, and to set the water temperature just as easily, according to the different comfort requirements. Furthermore, for the most demanding customers, it is possible to view all the information present on the integrated display as well as on the remote control (accessory). Thanks to the new patented OptiFlow technology, HYDROCOMPACTINDOOR is able to automatically calculate the combustion air flow, based on the power absorbed by the fan and the rotation speed of the fan itself. This guarantees: an optimal performance of the appliance in all operating conditions the reduction of the minimum power without the risk of condensation forming on the heat exchanger greatly reduced levels of CO2 emissions Furthermore, the automatic adaptation of the fan speed to the installation conditions (length of the intake/exhaust ducts and any obstructions) ensures simpler and faster installation. Small consumption, great performance With HYDROCOMPACTINDOOR, consumption optimization is guaranteed! Thanks to the high efficiency and the wide modulation range (1:7) the water heater is able to adapt the consumption of gas required to heat the water to the real demand for sanitary water withdrawal, thereby guaranteeing all the sanitary comfort you desire and maximum savings. Furthermore, HYDROCOMPACTINDOOR can be directly connected to thermal solar systems for the production of domestic hot water: all the energy of the sun for maximum comfort and minimum consumption! Characteristics: Extremely compact dimensions: the smallest instantaneous gas water heater available on the market Automatic recognition of the lengths of the suction/flue gas system thanks to the patented OptiFlow technology Efficiency final 94% Directly connectable to thermal solar systems for the production of domestic hot water, by means of a special TWM 20 mixing valve Easy and intuitive management, thanks to the large LCD display for adjusting the temperature and viewing information relating to the operation of the appliance Possibility of satisfying all comfort needs thanks to the completeness of the range, made up of 12, 15 and 18 l/min appliances High sanitary comfort reduction of gas consumption thanks to the electronic temperature control (stability, ¤ 1C) Reduction of consumption thanks to the wide modulation intervals (1:7) Possibility of managing the water heater remotely thanks to the accessory control Elegant design The ErP legislation and the new energy labels The future of heating systems Starting from 26 September 2015, heating systems for the production of hot water, in order to be placed on the market, will have to comply with the ErP regulations issued by the European Union. The ErP standards favor the eco-compatible design of products that consume energy from fossil fuels and have the aim of reducing energy consumption and CO2 emissions, as well as providing consumers with transparent and homogeneous information on the energy efficiency of appliances, favoring comparison. Regulations N 811/2013 and 812/2013 provide for a specific energy labeling of appliances for heating the production of domestic hot water. Regulations N 813/2013 and 814/2013 prescribe, among other things, the minimum energy efficiency and pollutant emissions requirements that manufacturers of equipment for heating and domestic hot water production must comply with. These regulations therefore raise energy efficiency standards, improving system performance and excluding less performing technologies from the market. The energy label will be supplied by the manufacturer with the appliance and will represent a concrete help for the consumer, allowing him to better understand the characteristics of the system, acquire greater awareness of energy saving, allowing him to choose better what to buy. The energy label will provide information on the energy class of the product, on a scale between A++ and G, and on other additional notations, such as power and noise emissions. The ErP legislation provides for two types of labelling: the first is supplied by the manufacturer together with the product for heating/domestic hot water production appliances the second for systems composed of several elements. In this second case, the label indicates the levels of energy efficiency that can be reached thanks to all the components used, allowing for an increase in the score attributed to each appliance and increasing the energy class of the system: therefore, it is the task of those who make/install the system to provide the consumer with the correct explanatory label. The ErP standards represent an opportunity to develop a market of highly efficient technologies, such as condensing, heat pumps, solar thermal, cogeneration and the integration of different energy sources in a single system. These technologies will have an impact on consumption in the home, approximately 80% of which is due to heating and the production of hot water, and are now tax-incentivized. Junkers Bosch is already in line with the dictates of the ErP legislation, demonstrating the orientamental futur that has always distinguished the brand. Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Overview GAS WATER HEATER JUNKERS HYDROCOMPACT OUTDOOR WTD 12 AM EO (12 LT) LPG 2 - FORCED DRAFT Sealed Chamber Water Heaters: Junkers Hydrocompact Outdoor, the new compact, quick and easy outdoor water heater. IN THE ABSENCE OF THE PRODUCT, THE NEW MODEL THERM 5600 SO 12 LPG WILL BE SUPPLIED Technical specifications DHW energy efficiency class (ErP): A Catalog code: WTD 12 AM EO Gas instantaneous water heater External installation Flame ionisation electronic ignition 2 - Forced draft sealed chamber water heaters Nominal heat output: 20.8 kW Nominal heat input: 22.5 kW Efficiency at 100% of rated power: 92% Efficiency at 30% of rated power: 94% Water flow rate supplied with DT 25 C: 12 l/min Maximum working pressure: 12 bar Minimum operating temperature with antifreeze kit: -25C (standard) Remote control: Standard Display: LCD multifunction (in remote control) degree of protection: IPX5D Dimensions (LxWxH): mm 170x300x568 Version: LPG Features list Hydrocompact Outdoor: Compact gas instantaneous water heaters for indoor use Finally out! HYDROCOMPACTOUTDOOR the new water heater in the Junkers range specially designed for outdoors: easy to install, simple to program. Outside with tranquillity HYDROCOMPACTOUTDOOR the new water heater designed for outdoors which expands the range of Junkers solutions for the production of domestic hot water. Thanks to the standard anti-freeze device and the IPX5D electrical protection degree, which represents one of the highest protection indexes against the infiltration of water and dust, HYDROCOMPACTOUTDOOR is resistant to the cold (up to -25 C) and bad weather, without any further precautions. Simple to install and operate Replacing your appliance with the new HYDROCOMPACT OUTDOOR has never been so simple! The new Junkers water heater, in fact, does not require any suction or flue gas system. The absence of suction and discharge pipes translates into minimal masonry work and extremely reduced installation times: in a single word, greater savings! HYDROCOMPACTOUTDOOR can be easily managed from inside the home, in an easy and intuitive way, thanks to the large display of the remote control. With a simple click it is possible to program the water heater to modify the hot water temperature at any time, to always have the maximum desired sanitary comfort. Small consumption, great performance HYDROCOMPACTOUTDOOR is presented on the market with a 1 liter plus: the completeness of the range, made up of 12, 15 and 18 l/min appliances, makes it possible to satisfy all comfort needs, from the smallest to the most complex. Furthermore, thanks to the high efficiency at the wide modulation range (1:7) the water heater is able to adapt the consumption of gas necessary to heat the water to the real demand for sanitary water withdrawal, thus guaranteeing all the sanitary comfort you desire and maximum savings. Furthermore, HYDROCOMPACTOUTDOOR can be directly connected to thermal solar systems for the production of domestic hot water. Characteristics: Instantaneous water heaters, 2 - Forced draft sealed chamber water heaters, with electronic temperature control (stability, ¤ 1C) For outdoor installations It does not require aspiration/flue gas systems Resistant to bad weather thanks to the anti-gel device (up to -25 C) and the IPX5D electrical protection degree Efficiency final 94% Directly connectable to thermal solar systems for the production of domestic hot water, by means of a special TWM 20 mixing valve Management from inside the home, easy and intuitive, thanks to the remote control with large LCD display for temperature regulation and viewing of information relating to appliance operation Flexibility of installation thanks to the compact dimensions. Furthermore, installing the remote control is very easy: it is not necessary to open the product because the electrical connection cable is positioned outside the water heater. Possibility of satisfying all comfort needs thanks to the completeness of the range, made up of 12, 15 and 18 l/min appliances High sanitary comfort reduction of gas consumption thanks to electronic temperature control (stability, ¤ 1C) Reduction of consumption thanks to the wide modulation intervals (1:7) Elegant design The ErP legislation and the new energy labels The future of heating systems Starting from 26 September 2015, heating systems for the production of hot water, in order to be placed on the market, will have to comply with the ErP regulations issued by the European Union. The ErP standards favor the eco-compatible design of products that consume energy from fossil fuels and have the aim of reducing energy consumption and CO2 emissions, as well as providing consumers with transparent and homogeneous information on the energy efficiency of appliances, favoring comparison. Regulations N 811/2013 and 812/2013 provide for a specific energy labeling of appliances for heating the production of domestic hot water. Regulations N 813/2013 and 814/2013 prescribe, among other things, the minimum energy efficiency and pollutant emissions requirements that manufacturers of equipment for heating and domestic hot water production must comply with. These regulations therefore raise energy efficiency standards, improving system performance and excluding less performing technologies from the market. The energy label will be supplied by the manufacturer with the appliance and will represent a concrete help for the consumer, allowing him to better understand the characteristics of the system, acquire greater awareness of energy saving, allowing him to choose better what to buy. The energy label will provide information on the energy class of the product, on a scale between A++ and G, and on other additional notations, such as power and noise emissions. The ErP legislation provides for two types of labelling: the first is supplied by the manufacturer together with the product for heating/domestic hot water production appliances the second for systems composed of several elements. In this second case, the label indicates the levels of energy efficiency that can be reached thanks to all the components used, allowing for an increase in the score attributed to each appliance and increasing the energy class of the system: therefore, it is the task of those who make/install the system to provide the consumer with the correct explanatory label. The ErP standards represent an opportunity to develop a market of highly efficient technologies, such as condensing, heat pumps, solar thermal, cogeneration and the integration of different energy sources in a single system. These technologies will have an impact on consumption in the home, approximately 80% of which is due to heating and the production of hot water, and are now tax-incentivized. Junkers Bosch is already in line with the dictates of the ErP legislation, demonstrating the orientamental futur that has always distinguished the brand. Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Overview GAS WATER HEATER JUNKERS HYDROCOMPACT OUTDOOR WTD 12 AM EO (12 LT) METHANE 2 - FORCED DRAFT Sealed Chamber Water Heaters: Junkers Hydrocompact Outdoor, the new compact, quick and easy outdoor water heater. IN THE ABSENCE OF THE PRODUCT, THE NEW METHANE THERM 5 600 SO 12 MODEL WILL BE SUPPLIED Technical specifications DHW energy efficiency class (ErP): A Catalog code: WTD 12 AM EO Profile of charge declared: M Gas instantaneous water heater for outdoor installation Flame ionisation electronic ignition 2 - Forced draft sealed chamber water heaters Nominal heat output: 20.8 kW Nominal heat input: 22.5 kW Efficiency at 100% of rated power: 92% Efficiency at 30% of rated power: 94% Water flow rate supplied with DT 25 C: 12 l/min Maximum working pressure: 12 bar Minimum operating temperature with antifreeze kit: -25C (standard) Remote control: Standard Display: LCD multifunction (in remote control) degree of protection: IPX5D Dimensions (LxWxH): mm 170x300x568 Version: CNG Features list Hydrocompact Outdoor: Compact gas instantaneous water heaters for indoor use Finally out! HYDROCOMPACTOUTDOOR the new water heater in the Junkers range specially designed for outdoors: easy to install, simple to program. Outside with tranquillity HYDROCOMPACTOUTDOOR the new water heater designed for outdoors which expands the range of Junkers solutions for the production of domestic hot water. Thanks to the standard anti-freeze device and the IPX5D electrical protection degree, which represents one of the highest protection indexes against the infiltration of water and dust, HYDROCOMPACTOUTDOOR is resistant to the cold (up to -25 C) and bad weather, without any further precautions. Simple to install and operate Replacing your appliance with the new HYDROCOMPACT OUTDOOR has never been so simple! The new Junkers water heater, in fact, does not require any suction or flue gas system. The absence of suction and discharge pipes translates into minimal masonry work and extremely reduced installation times: in a single word, greater savings! HYDROCOMPACTOUTDOOR can be easily managed from inside the home, in an easy and intuitive way, thanks to the large display of the remote control. With a simple click it is possible to program the water heater to modify the hot water temperature at any time, to always have the maximum desired sanitary comfort. Small consumption, great performance HYDROCOMPACTOUTDOOR is presented on the market with a 1 liter plus: the completeness of the range, made up of 12, 15 and 18 l/min appliances, makes it possible to satisfy all comfort needs, from the smallest to the most complex. Furthermore, thanks to the high efficiency at the wide modulation range (1:7) the water heater is able to adapt the consumption of gas necessary to heat the water to the real demand for sanitary water withdrawal, thus guaranteeing all the sanitary comfort you desire and maximum savings. Furthermore, HYDROCOMPACTOUTDOOR can be directly connected to thermal solar systems for the production of domestic hot water. Characteristics: Instantaneous water heaters, 2 - Forced draft sealed chamber water heaters, with electronic temperature control (stability, ¤ 1C) For outdoor installations It does not require aspiration/flue gas systems Resistant to bad weather thanks to the anti-gel device (up to -25 C) and the IPX5D electrical protection degree Efficiency final 94% Directly connectable to thermal solar systems for the production of domestic hot water, by means of a special TWM 20 mixing valve Management from inside the home, easy and intuitive, thanks to the remote control with large LCD display for temperature regulation and viewing of information relating to appliance operation Flexibility of installation thanks to the compact dimensions. Furthermore, installing the remote control is very easy: it is not necessary to open the product because the electrical connection cable is positioned outside the water heater. Possibility of satisfying all comfort needs thanks to the completeness of the range, made up of 12, 15 and 18 l/min appliances High sanitary comfort reduction of gas consumption thanks to electronic temperature control (stability, ¤ 1C) Reduction of consumption thanks to the wide modulation intervals (1:7) Elegant design The ErP legislation and the new energy labels The future of heating systems Starting from 26 September 2015, heating systems for the production of hot water, in order to be placed on the market, will have to comply with the ErP regulations issued by the European Union. The ErP standards favor the eco-compatible design of products that consume energy from fossil fuels and have the aim of reducing energy consumption and CO2 emissions, as well as providing consumers with transparent and homogeneous information on the energy efficiency of appliances, favoring comparison. Regulations N 811/2013 and 812/2013 provide for a specific energy labeling of appliances for heating the production of domestic hot water. Regulations N 813/2013 and 814/2013 prescribe, among other things, the minimum energy efficiency and pollutant emissions requirements that manufacturers of equipment for heating and domestic hot water production must comply with. These regulations therefore raise energy efficiency standards, improving system performance and excluding less performing technologies from the market. The energy label will be supplied by the manufacturer with the appliance and will represent a concrete help for the consumer, allowing him to better understand the characteristics of the system, acquire greater awareness of energy saving, allowing him to choose better what to buy. The energy label will provide information on the energy class of the product, on a scale between A++ and G, and on other additional notations, such as power and noise emissions. The ErP legislation provides for two types of labelling: the first is supplied by the manufacturer together with the product for heating/domestic hot water production appliances the second for systems composed of several elements. In this second case, the label indicates the levels of energy efficiency that can be reached thanks to all the components used, allowing for an increase in the score attributed to each appliance and increasing the energy class of the system: therefore, it is the task of those who make/install the system to provide the consumer with the correct explanatory label. The ErP standards represent an opportunity to develop a market of highly efficient technologies, such as condensing, heat pumps, solar thermal, cogeneration and the integration of different energy sources in a single system. These technologies will have an impact on consumption in the home, approximately 80% of which is due to heating and the production of hot water, and are now tax-incentivized. Junkers Bosch is already in line with the dictates of the ErP legislation, demonstrating the orientamental futur that has always distinguished the brand. Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

nb: discontinued product. the new therm 5600 model is shipped Technical characteristics Product data for energy consumption - according to requirements of EU regulations no. 811/2013 and 812/2013 to complete the directive 2010/30/EU CNG code: T4600 S 12-D 23 LPG code: T4600 S 12-D 31 Water heating energy efficiency class A Declared load profile M Forced draft sealed chamber Nominal heat output (Pn) [kW] 20.8 Nominal heat input (Qn) [kW] 22.5 Power setting/modulation range (Pn,min. - Pn,max.) [kW] 2.9-20.8 Max water flow with ΔT 25 °C [l/min] 12 Max water flow with ΔT 35 °C [l/min] 9 Efficiency at 100% rated power (on PCI) [%] 92 sound pressure max. [dB(A)] 67 Power supply [V(AC)] 230 Maximum absorbed power [W] 100 Degree of electrical protection [IP] IPX4D Weight (without packaging) [kg] 10 Dimensions (H x W x D) [mm] 568 x 300 x 170 Junkers Bosch water heaters With Junkers Bosch gas and heat pump water heaters you are assured of the best technology for the production of domestic hot water, always available and perfectly tailored to the user's needs: high quality, maximum efficiency and safety, ease of installation and control savings on bills. What to ask for more? Whatever your choice, choose quality. The wide range of Junkers Bosch gas and heat pump water heaters is able to meet the needs of your customers, to whom you can offer the most suitable solution for their home. Junkers Bosch gas water heaters are available in numerous models, to meet the most diverse needs: from the smallest ones, also suitable for being inserted in kitchen wall units, to those specifically designed for outdoor installation or for large buildings. Today it is possible to satisfy domestic hot water needs also through renewable energy sources: this allows not only economic savings, but also a contribution to environmental protection. Junkers Bosch heat pump water heaters are able to supply all the hot water needed in an efficient, convenient and sustainable way, obtaining energy from the external environment and using it to heat the water. Whatever your customers' requests, with Junkers Bosch you are sure to guarantee the best response. Environmentally friendly efficiency Choosing a gas water heater can also take advantage of renewable energy sources: all gas water heater models can be fully integrated, thanks to the Solar Kit accessory, in new or existing thermal solar systems, for exploit the inexhaustible energy of the sun for the production of domestic hot water. General characteristics THERM 4600 S Therm 4600 S is the extremely compact instantaneous gas water heater and thanks to its high efficiency it guarantees reduced consumption Advantages ▶ Comes with an easy and intuitive backlit LCD display ▶ It can be connected directly to solar thermal systems for the production of domestic hot water ▶ Guarantees reduced gas consumption thanks to the electronic temperature control ▶ Thanks to the OptiFlow patent, it automatically recognizes the lengths of the flue gas intake and exhaust system Characteristics ▶ Flame ionisation electronic ignition ▶ High efficiency and wide modulation range (1:7) ▶ Works even in case of very low water pressures ▶ Extremely compact dimensions ▶ Indoor installations The ErP legislation and the new energy labels The future of heating systems Starting from 26 September 2015, in order to be placed on the market, heating and hot water production systems will have to comply with the ErP (Energy Related Products) regulations issued by the European Union. The ErP standards favor the eco-compatible design of products that consume energy from fossil fuels and have the aim of reducing energy consumption and CO2 emissions, as well as providing consumers with transparent and homogeneous information on the energy efficiency of the appliances, favoring their comparison. Regulations N 811/2013 and 812/2013 provide for a specific energy labeling of appliances for heating and domestic hot water production. Regulations N 813/2013 and 814/2013 prescribe, among other things, the minimum energy efficiency and pollutant emissions requirements that manufacturers of equipment for heating and domestic hot water production must comply with. These regulations therefore raise energy efficiency standards, improving system performance and excluding less performing technologies from the market. The energy label will be supplied by the manufacturer with the appliance and will represent concrete help for the consumer, allowing him to learn more about the characteristics of the system, acquire greater awareness of the energy savings allowed and make the best choice of what to buy. The energy label will provide information on the energy class of the product, on a scale between A++ and G, and on other additional notations, such as power and noise emissions. The ErP legislation provides for two types of labelling: the former is supplied by the manufacturer together with the product for heating and/or domestic hot water production appliances the second for systems composed of several elements. In this second case, the label indicates the levels of energy efficiency that can be reached thanks to all the components used, allowing the score attributed to each appliance to increase and increasing the energy class of the system: it is therefore the task of whoever makes/installs the system to supply the consumer the correct explanatory label. The ErP standards represent an opportunity to develop a market of highly efficient technologies, such as condensing, heat pumps, solar thermal, cogeneration and the integration of different energy sources in a single system. These technologies will have an impact on home consumption, approximately 80% of which is due to heating and the production of hot water, and are already being incentivized at a tax level today. Junkers Bosch is already in line with the dictates of the ErP legislation, demonstrating the future orientation that has always distinguished the brand. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Gas water heater Sime Mini 12 BF sealed chamber complete with smoke exhaust kit cod. 8112630 Mini BF ErP 12 Nominal thermal power kW 21.0 Nominal heat input kW 24.0 Sanitary flow rate ∆t 25°C l/min 12 DHW energy efficiency class A ACS size M Maximum/minimum water pressure 7/0.2 bar Electric power absorbed W 33 IP degree of protection IPX4 Gas supply 1/2” Sanitary water inlet 1/2” Sanitary water outlet 1/2” CNG power supply Dimensions HxWxD 570x345x150 mm Sime Mini BF The Mini BF ErP water heater stands out for its modern line and its particularly small dimensions, especially in depth, which make it adaptable to any available space. It can be installed outdoors, in a partially protected place with a minimum design temperature of 0°C, it is equipped with automatic electronic ignition and flame modulation according to the water flow rate and can easily reach a correct and constant temperature, even with network pressure variations. Mini BF ErP can receive pre-heated water from a solar system with a temperature between 35° and 65°C. Depending on the selected setpoint and the inlet water temperature, the power is modulated to obtain maximum comfort, avoiding unnecessary switching on. CAN BE INSTALLED INDOOR OR OUTDOOR (In a partially protected place) INTERFACE WITH MULTIFUNCTION LED DISPLAY Prepared for solar thermal Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Product data for energy consumption - according to requirements of EU regulations no. 811/2013 and 812/2013 to complete the directive 2010/30/EU LPG code: T4600 S 12-D 31 Water heating energy efficiency class A Declared load profile M Forced draft sealed chamber Nominal heat output (Pn) [kW] 20.8 Nominal heat input (Qn) [kW] 22.5 Power setting/modulation range (Pn,min. - Pn,max.) [kW] 2.9-20.8 Max water flow with ΔT 25 °C [l/min] 12 Max water flow with ΔT 35 °C [l/min] 9 Efficiency at 100% rated power (on PCI) [%] 92 sound pressure max. [dB(A)] 67 Power supply [V(AC)] 230 Maximum absorbed power [W] 100 Degree of electrical protection [IP] IPX4D Weight (without packaging) [kg] 10 Dimensions (H x W x D) [mm] 568 x 300 x 170 Junkers Bosch water heaters With Junkers Bosch gas and heat pump water heaters you are assured of the best technology for the production of domestic hot water, always available and perfectly tailored to the user's needs: high quality, maximum efficiency and safety, ease of installation and control savings on bills. What to ask for more? Whatever your choice, choose quality. The wide range of Junkers Bosch gas and heat pump water heaters is able to meet the needs of your customers, to whom you can offer the most suitable solution for their home. Junkers Bosch gas water heaters are available in numerous models, to meet the most diverse needs: from the smallest ones, also suitable for being inserted in kitchen wall units, to those specifically designed for outdoor installation or for large buildings. Today it is possible to satisfy domestic hot water needs also through renewable energy sources: this allows not only economic savings, but also a contribution to environmental protection. Junkers Bosch heat pump water heaters are able to supply all the hot water needed in an efficient, convenient and sustainable way, obtaining energy from the external environment and using it to heat the water. Whatever your customers' requests, with Junkers Bosch you are sure to guarantee the best response. Environmentally friendly efficiency Choosing a gas water heater can also take advantage of renewable energy sources: all gas water heater models can be fully integrated, thanks to the Solar Kit accessory, in new or existing thermal solar systems, for exploit the inexhaustible energy of the sun for the production of domestic hot water. General characteristics THERM 4600 S Therm 4600 S is the extremely compact instantaneous gas water heater and thanks to its high efficiency it guarantees reduced consumption Advantages ▶ Comes with an easy and intuitive backlit LCD display ▶ It can be connected directly to solar thermal systems for the production of domestic hot water ▶ Guarantees reduced gas consumption thanks to the electronic temperature control ▶ Thanks to the OptiFlow patent, it automatically recognizes the lengths of the flue gas intake and exhaust system Characteristics ▶ Flame ionisation electronic ignition ▶ High efficiency and wide modulation range (1:7) ▶ Works even in case of very low water pressures ▶ Extremely compact dimensions ▶ Indoor installations The ErP legislation and the new energy labels The future of heating systems Starting from 26 September 2015, in order to be placed on the market, heating and hot water production systems will have to comply with the ErP (Energy Related Products) regulations issued by the European Union. The ErP standards favor the eco-compatible design of products that consume energy from fossil fuels and have the aim of reducing energy consumption and CO2 emissions, as well as providing consumers with transparent and homogeneous information on the energy efficiency of the appliances, favoring their comparison. Regulations N 811/2013 and 812/2013 provide for a specific energy labeling of appliances for heating and domestic hot water production. Regulations N 813/2013 and 814/2013 prescribe, among other things, the minimum energy efficiency and pollutant emissions requirements that manufacturers of equipment for heating and domestic hot water production must comply with. These regulations therefore raise energy efficiency standards, improving system performance and excluding less performing technologies from the market. The energy label will be supplied by the manufacturer with the appliance and will represent concrete help for the consumer, allowing him to learn more about the characteristics of the system, acquire greater awareness of the energy savings allowed and make the best choice of what to buy. The energy label will provide information on the energy class of the product, on a scale between A++ and G, and on other additional notations, such as power and noise emissions. The ErP legislation provides for two types of labelling: the former is supplied by the manufacturer together with the product for heating and/or domestic hot water production appliances the second for systems composed of several elements. In this second case, the label indicates the levels of energy efficiency that can be reached thanks to all the components used, allowing the score attributed to each appliance to increase and increasing the energy class of the system: it is therefore the task of whoever makes/installs the system to supply the consumer the correct explanatory label. The ErP standards represent an opportunity to develop a market of highly efficient technologies, such as condensing, heat pumps, solar thermal, cogeneration and the integration of different energy sources in a single system. These technologies will have an impact on home consumption, approximately 80% of which is due to heating and the production of hot water, and are already being incentivized at a tax level today. Junkers Bosch is already in line with the dictates of the ErP legislation, demonstrating the future orientation that has always distinguished the brand. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less