Discover our exclusive collection of Ferroli boilers, air conditioners and water heaters. Choose comfort and efficiency with our quality products. Reach maximum domestic comfort with Ferroli. Explore our collection today.
Ferroli
Ferroli Ferroli Bluehelix Alpha 34c Methane Or LPG Condensing Boiler 0tpf7awa Complete With Smoke Exhaust Kit
ATTENTION Methane, LPG, Propane air Ready through a simple configuration the boiler is able to operate on methane, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli condensing boiler Bluehelix Alpha 34C complete with methane or LPG fume exhaust kit cod. 0TPF7AWA Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating max / min heat input (Hs) kW 34.1 / 5.5 Max DHW heat input (Hi) kW 34.8 Max working pressure heating bar 3 Min. heating operating pressure bar 0.8 Heating expansion vessel capacity 10 litres Max DHW working pressure bar 9 Minimum DHW operating pressure bar 0.3 Sanitary flow rate ∆t 25°C l/min 19.5 Protection degree (IEC 60529) IP IPX4D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x320 Bluehelix Alpha .. More beautiful than "BEFORE" The new range of generators is equipped with the tested heat exchanger in stainless steel . Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX ALPHA is at the top of its category. TOP EFFICIENCY EVEN ON OLD SYSTEMS (REPLACEMENTS) mod. 24 C COMBINED (14 l/min at ∆t 25°C) The BLUEHELIX ALPHA thermal group exchanger (fig. A) compared with the more classic and widespread steel exchanger. This geometry allows the exchanger to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig. B tends to block up much faster in the part in contact with the flame due to the reduced passage area of the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values BLUEHELIX ALPHA FROM THE INSIDE EXCHANGER High flow single circuit stainless steel exchanger, resistant to clogging and easy to clean STEEL FRAME Made with high precision automated processes EXPANSION TANK 8 liter expansion tank placed on the side ELECTRIC PANEL FAN Offset fan, to facilitate maintenance of the primary exchanger without disassembly DOMESTIC HOT WATER EXCHANGER In stainless steel, with copper brazing CIRCULATOR High efficiency, for heating and exchange with the DHW circuit SEALED CHAMBER Removable steel panel to protect the combustion chamber with the function of a sealed chamber ELECTRICAL PANEL Large removable electrical panel to protect against water damage that may occur during normal maintenance. Easy access to electrical connectors. THE ENGINE The tube that makes up the BLUEHELIX ALPHA exchanger is made of stainless steel, a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits. THE BOILER CONTROL The control box of BLUEHELIX ALPHA consists of an easy to use interface with backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. MC2 The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). MGR Methane, LPG, Propane Ready Air The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). Thanks to the new electronics supplied, the gas change operation is extremely simple. The MC2 combustion control performs constant monitoring of the quality of the combustion and by simply modifying a parameter on the electronic card (operation to be carried out only by qualified personnel) it is possible to operate the boiler on Natural Gas or LPG or Propane Air. It is therefore not necessary to purchase additional accessory kits. CONNECT New wireless remote control available as an accessory for home comfort management also from a smartphone using the connect app (iOS and Android). Maximizes room comfort with delivery temperature modulation through the Room Climatic Compensation (CCA) and External Climatic Compensation (CCE) functions via the external temperature detectable directly from the internet (or from an optional external probe). It improves the average seasonal efficiency in space heating by +4%. EASY MAINTENANCE Problem-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the BLUEHELIX ALPHA thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: - The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - Easy access to the burner unit by removing 4 screws and the quick coupling (clip) of the fan. - The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. - The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. - Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front SUN EASY FUNCTION BLUEHELIX ALPHA has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. By means of a sensor located on the DHW circuit, it continuously controls the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. STOP AND GO FUNCTION With the use of sanitary mixing taps, short or very short dispensing for quick rinses involves the start of the boiler ignition procedure which usually ends immediately. The continuation of these "false starts" can, in the long run, compromise the average life of the product. For this reason BLUEHELIX ALPHA provides an electronic parameter through which it is possible to delay burner ignition (Stop and Go) by activating it only in the face of actual withdrawals of domestic hot water. OUTDOOR INSTALLATION - ANTIFREEZE FUNCTION To make the most of the available space, the new BLUEHELIX ALPHA 24 - 28 C boiler can be installed recessed into the wall thanks to the special kit; for more critical installations, in completely uncovered places not protected from atmospheric agents, the "painted cabinet" kit is also available. In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. SANITARY ECO-COMFORT FUNCTION In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable. The efficiency and the load profiles according to the ErP directive are at the top of the category: mod. 24 C / A - XL. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€798,00
-
Ferroli Ferroli Condensing Boiler Bluehelix Hitech Rrt 28 K 50 With 50 Liters Accumulation Free Smoke Exhaust Kit Low Nox Methane Or LPG - New
Ferroli condensing boiler Bluehelix HiTech RRT 28 K 50 with 50 liter storage tank low NOx flue gas kit for methane or LPG - New Heat input Min / Max Heating 3.5 / 24.5 Min / Max Sanitary heat output 28.5 Heating power Min / Max Heating 3.4 / 24.0 Thermal power 28 max Useful thermal efficiency 80°C-60°C Pmax % / Pmin % 98.1 / 98.0 NOx class 6 Boiler capacity 50 litres Heating efficiency class A Sanitary Efficiency Class A XL load profile Dimensions HxWxD mm 807x600x434 Bluehelix HiTech RRT K 50 > STRONG POINTS: - Boiler with thick stainless steel primary exchanger , with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt - : in combination with the modulating remote control and the external probe (optional) it reaches the upper efficiency class A+ (scale from G to A+++) - Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:10 (mod. 34) - MC2 : Multi Combustion Control, new combustion system with patented gasadaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) - MGR: Methane, LPG, Propane air Ready through a simple configuration the boiler is able to operate on methane, LPG and propane air without the use of additional conversion kits - Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace. - Production of domestic hot water with 50 liter stainless steel storage tank - Arrangement for recirculation attachments (present in the accessory: attachment connection kit) - Hydraulic connections covered by the boiler casing - Standard by-pass - "Range Rated" certified generator: the maximum heat input in heating mode can be adapted to the heat requirements of the system while maintaining the efficiency values declared in the approval > BENEFITS OF BLUEHELIX HITECH RRT K 50: - Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes - FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard - Designed to simplify and facilitate normal maintenance and cleaning operations - Anti-legionella function with programmable timing from 1 to 7 days - Timed anti-blocking for circulator and three-way valve - Sliding temperature operation via optional external probe - Place of installation: also for outdoors in a partially protected place up to -5°C as standard - Free methane/LPG/propaneted air transformation during the initial product check and activation of the conventional guarantee, to be requested from the Authorized Assistance Center
€1.902,00 - €1.980,00
-
Ferroli Area Occasioni Condensing Boiler Ferroli Divacondens D Plus F24 Low Nox Methane Complete With Coaxial Flue Kit
ATTENTION THE PRODUCT IS NEW AND 100% WORKING, BUT HAS DENT ON THE TOP (SEE PHOTO NEXT TO THE MAIN IMAGE) NB The boiler will be supplied with methane, for LPG operation you must contact your local Authorized Assistance Centre. Technical features Model : Divacondens D Plus Nominal thermal power: 24 kW Power supply: methane Specifications Energy efficiency according to the European ErP directive Heating Energy Efficiency Class: B Seasonal Space Heating Energy Efficiency : 89% Performance Heating Thermal Capacity : 7,5 ~ 25,0 kW Heating Thermal Power: 7.2 ~ 24.2 kW Ultimate Thermal Efficiency 30% Pmin : 100.1% Domestic Hot Water Production 25°C Δt 30°C : 13,9 ~ 11,6 l/min NOx emissions 6 Dimensions and weight Dimensions (LxHxP): 400x700x330 mm Weight : 35Kg Ferroli Divacondens D Plus Boiler The Simplest Solution For A Condensing Boiler DIVACONDENS D PLUS is the condensing heat generator for traditional heating systems. The tried and tested Ferroli technology in the field of traditional wall mounted boilers has been enriched by increasing the performance of the product in the simplest way, with the use of a robust recuperator which preheats the primary circuit using the residual heat of the exhaust fumes and a new cooled burner with low NOx emissions. The Range Divacondens D Plus is offered in a single model for heating and instantaneous production of domestic hot water Characteristics > Condensing boiler for heating high temperature systems and producing domestic hot water. It is not suitable for combination with direct delivery to systems with low temperature radiant panels > Compact geometry primary exchanger > Instant production of domestic hot water with dedicated plate exchanger > Post-recovery of the latent heat of condensation, in function of pre-heating of the primary circuit > Forced draught sealed chamber boiler, with water-cooled atmospheric burner with low NOx emissions > Standard automatic hydraulic by-pass > Minimum polluting emissions (class 6 according to EN 15502-1) > High efficiency low consumption circulator (ErP - Class A) with anti-blocking system by activation for a few seconds every 24 hours of inactivity > Can be combined with the modulating remote timer control > Simple and complete control panel, display user interface, with setting keys > Robust post-condenser fed by the closed circuit of the primary. The heat exchange with the fumes takes place inside large diameter water passages. > Generator with simple and rational operation > ECO function in DHW for greater savings in the period of low use of hot water > Predisposition for solar systems: prearranged for the production of domestic hot water combined with solar panel systems > Place of installation: also for outdoors in a partially protected place down to -5°C as standard > Certified operation also with propane air (50% air - 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center > Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre Boiler control The DIVACONDENS D PLUS control unit consists of an easy-to-use interface with a backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. The performances Energy classification DHW load profile (maximum flow rate at the corresponding efficiency declared in DHW) Efficiency in the production of domestic hot water FOR COMBINED BOILERS The "climate-energy 20/20/20" package sets ambitious targets for the reduction of greenhouse gas emissions, of energy consumption as well as the increase in the use of renewable energies, corresponding to a percentage of 20% to be reached by 2020. In this context, the European regulation ErP (Energy Related Products) introduces an energy classification also for water generators hot water for space heating and domestic hot water purposes. This classification translates into an energy label which must necessarily accompany all the products affected by the Regulation, introduced on the market from 26 September 2015. The labeling constitutes an easy guide for the consumer, who can choose - through standardized and objective indications - the product more efficient. In this way, the choice will be the most sparing in terms of consumption for the benefit of the user, but also the most virtuous for energy balances and consequently, for the environment. The most significant parameters indicated on the label are the seasonal efficiency index in heating and efficiency in the eventual production of domestic hot water, according to a scale which, in the case of the single boiler product, ranges from A to G*. Furthermore, for combined boilers, a load profile is indicated corresponding to the DHW flow rate of the appliance measured in a series of typical samplings, guaranteeing at least the declared DHW efficiency. This index is identified with a letter/”size” (S, M …XXL). Solar circuit integration DIVACONDENS D PLUS boasts electronics that simplify integration with thermal solar systems, both with natural and forced circulation. The microprocessor controls the temperature of the water coming from the solar circuit through the domestic hot water sensor and turns on the burner only if necessary. To reach the desired temperature, SUN EASY allows considerable savings even during the coldest seasons, exploiting and integrating even the smallest solar contribution, otherwise lost. In case of insufficient irradiation and therefore a modest pre-heating of the domestic water, the boiler will contribute with the heat necessary to reach the required set point temperature. If the sun and the solar system fulfill their "duty" no integration by the boiler will be necessary, the hot water will be conveyed to the tap, without the need for additional devices, with the mixing of the thermostatic valves. Safety and comfort ANTIFREEZE In the event that the temperature in the boiler drops to 5°C, the burner ignites automatically and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. POST-CIRCULATION This function makes it possible to recover all the heat supplied by thermal inertia of the exchanger and transfer it to the heating system, and consequently to the rooms to be heated. This is a timer function (customizable duration) and is active after the burner goes out in heating mode. SLIDING TEMPERATURE OPERATION With the installation of the “external probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. EASY CONTROL The electronic board of DIVACONDENS D PLUS adopts the Opentherm protocol. It allows the integration of other peripheral control units such as, for example, the ROMEO remote timer control. In fact, the Opentherm standard has been specially designed to share the logic and operating algorithms of the boiler with other additional control units. As a digital protocol, it allows total integration between the boiler and the satellite, with full control of the functions from the boiler and similarly from its satellite. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€425,00
-
Ferroli Ferroli Econcept In St 25 Kw Condensing Built-in Boiler With Stainless Steel Dynamic Accumulation 25 Liters Methane Complete With Smoke Exhaust Kit
OFFER VALID UNTIL STOCKS LAST BUILT-IN BOX TO BE PURCHASED SEPARATELY Technical features Model : ECONCEPT IN ST 25 Product code : 0M7Y4IAA Maximum heat input in heating mode: 25.2 kW Maximum heat output in sanitary mode: 27.0 kW Efficiency (50-30°C) Pmax % 105.4 NOx emissions class: 5 Heating maximum operating temperature: 95°C Heating working pressure: 3 bar Heating expansion vessel capacity: 8 litres Dimensions and weight Dimensions (HxWxD): 1100x700x245 mm Weight : 42.0 Kg MAXIMUM COMFORT IN HEATING AND DOMESTIC HOT WATER DELIVERY ECONCEPT ST/ IN ST are the products with which FERROLI intends to satisfy the new and more selective limits on energy consumption imposed by recent regulations, while still providing maximum comfort in space heating and in the supply of domestic hot water ECONCEPT ST The ECONCEPT ST range has been designed by drawing on the most advanced knowledge available today. The combustion and exchange group makes use of condensing technology while for the production of domestic hot water a dynamic stratification boiler has been adopted, capable of satisfying several users in a constant and continuous manner. The generator is of the sealed chamber and forced draught type. Thanks to a pre-mixed air/gas supply system and the inverted micro-flame ceramic burner, it falls within the 5th class for NOx emissions. The efficiency of ECONCEPT ST is the best in its category. It is in fact certified with 4 stars according to the 92/42 EEC Directive concerning energy classification. The built-in model ECONCEPT IN ST has been designed to offer a solution to space problems. The compactness of the collection allows a wide choice of solutions for installation both inside and outside the home, in partially protected places. The built-in solution is offered in a single 25 kW size and with the same DHW storage tank as the wall-mounted models. ANTI-LEGIONELLA FUNCTION Legionella is a typical form of water contamination caused by bacteria that are particularly harmful to health; they can be shot down bringing the water temperature to a value higher than 60°C. It is for this reason that ECONCEPT ST / IN ST, at least once a week, they heat the DHW storage water up to 65°C regardless of the value set with the thermostat. OPERATION IN SLIDING TEMPERATURE With the installation of the "external probe" kit it is possible to operate the boiler in sliding temperature. This means that without acting on the keys of regulation of the system temperature, the boiler will self-regulate according to the variations in external temperatures. This results in a energy saving while ensuring maximum comfort for the user. ANTIFREEZE FUNCTION Even in stand-by mode (provided with electricity and gas supplies), i.e. in the absence of a request for heat, if ECONCEPT ST / IN ST detects a water temperature of 5°C, activates the anti-freeze protection by igniting the burner at minimum power, in order to avoid damage due to freezing. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€500,00
-
Ferroli Ferroli Bluehelix Pro S 27c Kw LPG Condensing Gas Boiler Complete With Fume Exhaust Kit - New Erp
OPTIONAL RECESSED ENCLOSURE FERROLI BLUEHELIX PRO S 27 kW CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Heating ERP class: A Healthcare ERP class: A Load profile: XL Heating capacity (PCI) Min / Max Heating 5.3 / 25.2 Heating power 80°C-60°C Min / Max Heating 5.2 / 24.6 kW Useful thermal efficiency 80°C-60°C Pmax % / Pmin % 98.3 / 97.3 Domestic hot water production Δt 30°C 12.7 l/min Heating working pressure Max / Min bar 3 / 0.8 Empty weight kg 32 Dimensions (HxWxD): 700x420x260 mm BLUEHELIX PRO S SMALL FOOTPRINT, GREAT PERFORMANCE ... FULL CONDENSATION BLUEHELIX PRO S has been designed to guarantee maximum energy efficiency and performance both in heating and in the supply of domestic hot water thanks to the new bivalent exchanger in Aisi 316 Ti stainless steel. This new exchanger integrates the heating circuit and the production of instantaneous domestic hot water in a single element, thus optimizing the phenomenon of condensation. The galvanized sheet casing, supplied separately from the boiler body, has been designed to facilitate access to the hydraulic connections and to allow the smoke ducts and air intake pipes to exit on each side of the same. Bluehelix Pro S achieves one of the highest energy efficiency of space heating in its category: ηs 94% . Furthermore, when combined with the external probe and the Romeo remote timer control, it reaches system energy class A+ . Strengths: - Achieves one of the highest seasonal space heating efficiency in its category: ηs 94% - A+ SYSTEM : in combination with the Romeo modulating remote timer control and the external probe - Primary heat exchanger in thick Aisi 316 Ti stainless steel with integrated sanitary production (dual stainless steel heat exchanger) - Total premix burner in stainless steel - Digital control panel - Electronic flame modulation both in heating and DHW - Can be combined with the modulating remote timer control - Large backlit multifunction graphic display for easy and correct setting of the parameters - Standard by-pass Advantages: - Exchanger with "SELF-CLEANING" function which reduces limescale deposits inside the DHW circuit - High yields both in heating and in sanitary production - Ease of access to internal components for any maintenance - ECO function in DHW for greater savings in the period of low use of hot water - 3-star certified comfort in sanitary production according to EN 13203, amended by Reg. 812/2013 - Sliding temperature operation via optional external probe - Low consumption modulating heating pump (Erp Ready - Class A) - Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) - Predisposition for solar systems : prearranged for the production of domestic hot water combined with solar panel systems - Certified operation also with propane air (50% air - 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center (max total price of 30 euros + VAT) - Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre. Free transformation during product verification and activation of the guarantee only if the specific code running on LPG is not available. Functions: ECO-COMFORT function : In COMFORT mode, thanks to the particular system for maintaining the temperature of the heat exchanger, the dispensing of domestic hot water becomes even faster and more comfortable. In ECO mode, the production of domestic hot water takes place according to traditional standards. Sliding temperature operation : With the installation of the “External probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. Antifreeze function : In the event that the temperature in the boiler drops to 5°C, the burner automatically turns on and the circulator is activated in order to protect the appliance from damage caused by freezing. This function is active with the boiler powered by the gas circuit and under electrical voltage. Sun Easy function : BLUEHELIX PRO S has been designed to be easily inserted in systems made with the latest technologies. The SUN EASY system, standard on the boiler, makes use of electronics that simplify the combination with both natural and forced circulation solar panels. Through a sensor placed on the DHW circuit, it continuously monitors the temperature of the water coming from the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user.
€660,00
-
Ferroli Ferroli Bluehelix Top Rrt K 50 34c Methane or LPG Condensing Boiler Complete with Fume Exhaust Kit Cod. 0t3t3awa Low Nox - New
ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli Bluehelix TOP RRT K 50 34C methane or LPG condensing boiler Complete with Smoke Exhaust Kit cod. 0T3T3AWA low NOx - NEW Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XXL Class A Characteristics of heating/DHW operation: Heating max / min heat input (Hs) kW 34 / 7.1 Heating power max / min heating (80/60°C) kW 30 / 6,3 Max DHW heat input (Hi) kW 34.7 Min DHW heat input (Hi) kW 6.4 Max / min DHW thermal power kW 34.0 / 6.3 NOx emission class (EN 15502-1) - 6 Max working pressure heating bar 3 Sanitary flow rate ∆t 30°C l/10min 195 Protection degree (IEC 60529) IP X5D Supply voltage V/Hz 230V / 50Hz BLUEHELIX TOP RRT K 50 BLUEHELIX TOP RRT K 50... THE EVOLUTION IS COMPLETE This range of generators is equipped with the tested primary heat exchanger in stainless steel and a 50-litre domestic hot water storage tank, also in stainless steel. Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX TOP RRT K 50 is at the top of its category. BLUEHELIX TOP RRT K 50 achieves one of the highest energy efficiency of space heating in the boiler category: ηs 94% (Class A ErP, scale from G to A++). Furthermore, when combined with the external probe and the Romeo remote timer control or the new Connect control, it reaches system energy class A+ (scale from G to A+++). TOP EFFICIENCY EVEN ON OLD SYSTEMS (REPLACEMENTS) The THERMOBALANCE™ heat exchanger of BLUEHELIX TOP RRT K 50 (fig. A) compared to the more classic and widespread steel exchanger (fig. B), abandoned in favor of the evolution towards the primary steel exchanger used in the models Bluehelix (2012 -> ). This geometry allows the heat exchanger of the THERMOBALANCE heating unit to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig . B tends to block up much faster in the part in contact with the flame due to the reduced passage area of the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values. INNOVATIVE THERMAL GROUP FERROLI THERMOBALANCE TM IN ITS 5 ELEMENTS Ferroli has oriented the design of the combustion cell and the exchanger of BLUEHELIX TOP RRT K 50 in order to maximize the functional advantages and the constructive sturdiness, as well as the simplicity of maintenance: the single-circuit design means that any air bubbles in the system do not remain trapped in the exchanger, and facilitates cleaning with chemical washing as much as possible, unlike spiral exchangers with double parallel circuit (more common) in which if only one of the circuits is blocked, chemical washing is much more laborious. THE ENGINE The tube that makes up the BLUEHELIX TOP RRT K 50 exchanger is made of stainless steel, a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits. TOP QUIETNESS The particularly careful design of BLUEHELIX TOP RRT K 50 has made it possible to achieve significant values in terms of silence and acoustic comfort, so much so that it could almost be difficult to distinguish the background noise of a home from the noise produced by the boiler during normal operation. . Even the boiler on/off transients have been optimized as a function of acoustic comfort, so that the customer will no longer have the hassle of understanding whether the boiler is on or off from its noise as with older generations of boilers. The planning also took care of the design, creating a precious mantle in 3 removable pieces, which descends to cover the pipe connections. THE BOILER CONTROL The control and management electronics allow the user to customize the operation of the appliance in order to manage the environmental comfort according to one's needs. The key control panel and the simple LCD display make the programming operations for the production of hot water, both for domestic hot water and for heating, extremely easy and intuitive. Thanks to the remote connection via bus, this can also be done directly from the remote control. The card is protected by an easily accessible fuse thanks to the dedicated flap and the electrical connections benefit from a robust and large box, with easily accessible connectors and numerous cable ties. The boiler is also set up to connect a second room thermostat to the dedicated terminals to manage multi-zone mixing systems. MC2 The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2: Multi Combustion Control, the new combustion system with patented gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). EASY MAINTENANCE At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the "Thermobalance"TM thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: Internal accessibility is favored by the 3-piece mantle with removable side panels. The electrical box of the electronic board can be easily rotated on the chassis leaving free access to the internal parts. The fan, offset from the burner and placed underneath, must not be disassembled to access the steel burner-exchanger group. The burner door is totally self-air-cooled and therefore does not require an insulating panel, avoiding the risk that this could be damaged or broken during disassembly for cleaning. The burner can be disassembled by loosening just 3 bolts leaving free access to the stainless steel exchanger. The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections SIMPLIFIED REPLACEMENT The new boiler can also be installed with 50mm diameter ducting outlets. Particularly important in the replacement market in the frequent case of collective flues that require "heavy" ducting where it is necessary to have a high fume expulsion capacity even with reduced diameters. STOP AND GO FUNCTION With the use of sanitary taps with mixing, short or very short dispensing for quick rinses involves the start of the boiler ignition procedure which usually ends immediately. The continuation of these "false starts" can, in the long run, compromise the average life of the product. For this reason BLUEHELIX TOP RRT K 50 provides an electronic parameter through which it is possible to delay burner ignition (Stop and Go) by activating it only in the face of actual withdrawals of domestic hot water SUN EASY FUNCTION BLUEHELIX TOP RRT K 50 has been designed to be easily inserted into systems built with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. Through a sensor placed on the DHW circuit, it continuously monitors the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter falls below the level necessary to guarantee optimal comfort for the user SANITARY ECO-COMFORT FUNCTION In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable. Achieving maximum comfort certified 3 stars (EN 13203). The efficiency and the load profiles according to the ErP directive are at the top of the category: mod. 28 / A - XL | mod. 34/A - XXL MODULATION RANGE The new control electronics allow to reach high modulation fields which can reach up to 1:12 for the 34 K 50 model (1:10 for the 28 K 50). In this way BLUEHELIX TOP RRT K 50 is able to adapt to the effective power required by the system with extreme ease and efficiency, avoiding annoying on/off type operations which increase operating costs and reduce the average life of the product. PRODUCT ADVANTAGES Boiler with thick stainless steel primary exchanger, with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt A+ : combined with the modulating remote control and the external probe (optional) it reaches the higher efficiency class A+ (scale from G to A+++) Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:12 (mod. 34, 1:10 mod. 28) MC2 : Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) > MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace. Domestic hot water production with 50 liter stainless steel storage tank Arrangement for recirculation connections (present in the accessory: connection connection kit) Hydraulic connections covered by the boiler shell > Standard by-pass Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard Designed to simplify and facilitate normal maintenance and cleaning operations Anti-legionella function with programmable timing Timed anti-blocking for circulator and three-way valve 3-star certified comfort in sanitary manufacturing according to EN 13203 Minimum polluting emissions (class 6 according to EN 15502-1) Sliding temperature operation via optional external probe Low consumption modulating heating pump (ErP Ready - Class A) Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) Free methane/LPG/propaneted air transformation during the initial product check and activation of the conventional guarantee, to be requested from the Authorized Assistance Center Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€2.075,00
-
Ferroli Ferroli Condensing Boiler Bluehelix Hitech Rrt 24 C Complete With Low Nox Methane Or LPG Flue Kit - New
Ferroli condensing boiler Bluehelix HiTech RRT 24 C complete with low NOx methane or LPG fume exhaust kit - New Heating ERP Class A Healthcare ERP Class A XL load profile Heating capacity max / min kW 20.4 / 3.5 Max DHW heat input (Hi) kW 25.0 Max / min DHW thermal power kW 24.5 / 3.4 Yield 30% % 109.7 NOx emission class (EN 15502-1) - 6 Heating expansion vessel capacity 8 litres Sanitary flow rate ?t 25°C l/min 14 Protection degree (IEC 60529) IP X4D Dimensions HxWxD mm 700x420x320 Bluehelix HiTech RRT The new user interface with «capsense» technology, without mechanical keys and equipped with a 2.8'' graphic display, allows the user to interact with the product easily and extremely simply. Thanks to the energy efficiency of the space heating ηs 94% among the highest in the category (Class A ErP, scale from G to A++) and to the combination with the Connect remote control, able to read the external temperature directly from the internet, reaches the system energy class A+ (scale from G to A+++). Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:10 (1:10 mod. 34 C, 1:9 mod. 28 C, 1:7 mod 24 C). Thanks to the "Hydrogen plug-in" system, one of its most important innovations, it is already able to self-regulate to work with mixtures of natural gas and hydrogen, which will soon arrive in Europe, to combat global warming. Designed to fully satisfy the requests for a "robust" product from every point of view thanks to the high-passage primary exchanger capable of guaranteeing maximum efficiency and reliability over time also, and not only, as a replacement for old generators in particularly dirty systems . Silence at the top The particularly careful design of BLUEHELIX HITECH RRT has made it possible to achieve significant values in terms of silence and acoustic comfort, so much so that it could almost be difficult to distinguish the background noise of a home from the noise produced by the boiler during normal operation. It will be difficult to realize whether the boiler is on or off from its noise, as on older generations of boilers, because even the on/off transients have been optimized according to acoustic comfort. The planning also took care of the design, creating a precious mantle in 3 removable pieces, which descends to cover the pipe connections Characteristics Boiler with thick stainless steel primary exchanger , with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt thanks to the combination with the CONNECT modulating remote control and the reading of the external temperature directly from the internet, it reaches the maximum energy efficiency A+ (scale from G to A+++) Class 6 NOx: already in line with the provisions of the ErP regulation from 26.09.2018 (NOx emissions < 56mg/kWh) MC2: Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) MGR: Methane LPG Ready, through a simple configuration the boiler is able to operate on both methane and LPG without the use of additional conversion kits Exclusive exchanger-burner system with self-cooled door (without insulators): simplifies maintenance and reduces its cost thanks to fewer perishable parts Instantaneous production of DHW with dedicated DHW plate heat exchanger (only for version C) Hydraulic connections covered by the boiler shell Large backlit multifunction graphic display for easy and correct parameter setting Standard by-pass Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:10 (1:10 mod. 34 C, 1:9 mod. 28 C, 1:7 mod 24 C). Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard Designed to simplify and facilitate normal maintenance and cleaning operations Predisposition for solar systems: prepared for the production of domestic hot water combined with solar panel systems ECO function in DHW for greater savings in the period of low use of hot water (only for version C) Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (only for methane operation) Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit Boiler control The new user interface with ''capsense'' technology, without mechanical keys and equipped with a 2.8'' graphic display, allows the user to interact with the product easily and extremely simply, customizing the operation of the appliance in so as to manage the environmental comfort according to one's needs. Thanks to the remote connection via bus, this can also be done directly from the CONNECT remote control, even via smartphone. The boiler is also set up to connect a second room thermostat to dedicated terminals to manage multi-zone systems. TOP EFFICIENCY Even on old systems (replacements) The BLUEHELIX HITECH RRT heat exchanger THERMOBALANCE™ (fig. A) compared to the more classic and widespread steel exchanger (fig. B) also used in the past by the Ferroli Group exclusively on a small series of boilers produced for the market English, and then immediately abandoned in favor of the evolution towards the proprietary steel exchanger used in the Bluehelix models (2012 -> ). This geometry allows the heat exchanger of the THERMOBALANCE heating unit to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig . B tends to block up much faster in the part in contact with the flame due to the reduced passage area of the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values MC2 Multi Combustion Control The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). EASY MAINTENANCE Trouble-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the "Thermobalance"TM thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: Internal accessibility is favored by the 3-piece mantle with removable side panels. The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - The fan, offset from the burner and placed underneath, must not be disassembled to access the steel burner-exchanger group. The burner door is totally self-air-cooled and therefore does not require an insulating panel, avoiding the risk that this could be damaged or broken during disassembly for cleaning. The burner can be disassembled by loosening just 3 bolts leaving free access to the stainless steel exchanger. The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€880,00
-
Ferroli Ferroli Divacondens D F24 LPG Condensing Boiler Complete With Smoke Exhaust Kit
LPG operation with the use of a special conversion kit to be requested from the Authorized Assistance Centre, we recommend contacting the local assistance center before purchasing In case of unavailability we will supply the new model DIVACONDENS D PLUS F24 LOW NOx Technical features Model : Divacondens D F24 Power supply: LPG Energy efficiency Heating energy efficiency class: B Sanitary energy efficiency class: A ACS profile : XL Performance Heat output : 10.0 ~ 25.0 kW Thermal power 80°C ~ 60°C : 9.2 ~ 24.1 kW Thermal power 50°C ~ 30°C : 9.6 ~ 25.9 kW Useful thermal efficiency 80°C ~ 60°C : 92.0% ~ 96.5% Useful thermal efficiency 50°C ~ 30°C : 96.0 ~ 103.5% NOx emissions : 3 Maximum production of domestic hot water Δt 25°C : 14.0 l/min Maximum production of domestic hot water Δt 30°C : 11.6 l/min Heating working pressure: 0.8 ~ 3 bar Sanitary operating pressure: 9 bar Dimensions and weight Dimensions (LxHxP): 400x680x330 mm Empty weight: 35.0 kg 5 years without worries Extension of the manufacturer's standard warranty to 5 YEARS on Ferroli brand gas condensing boilers of less than 35 kW in the DIVACONDENS and BLUEHELIX series through the local authorized Ferroli technical assistance centre. Wall mounted boiler Ferroli DIVACONDENS Wall mounted condensing boiler with instantaneous production of domestic hot water The simplest solution for a condensing boiler DIVACONDENS is the condensing heat generator for traditional heating systems. The tried and tested Ferroli technology in the field of traditional wall mounted boilers has been enriched by increasing the performance of the product in the simplest way, with the use of a robust recuperator which preheats the primary circuit using the residual heat of the exhaust fumes. The quality of the DIVACONDENS line is unquestionable, and Ferroli is ready to put it to the test by offering its customers extended warranty coverage which also ensures periodic maintenance and legal checks Product plus > Forced draft boiler, atmospheric burner in AISI 304 stainless steel, for traditional medium and high temperature systems . It is not suitable for combination with direct delivery to systems with low temperature radiant panels > Multi-zone management possible with the use of the Ferroli FZ4 control unit > Double exchanger : copper primary with aluminum cladding; secondary in stainless steel for domestic hot water > Exhaust gas heat recovery unit , for pre-heating the primary circuit > Backlit liquid crystal display that is easy to use for the user > Possible combination with modulating remote control > High efficiency circulator for the primary circuit, synchronous motor with low operating noise and torque control > Timed anti-blocking system of the circulator and the diverter valve > Domestic hot water pre-heating function for rapid delivery to the user > Smoke accessories in special polypropylene , less prone to thermal expansion than metal ones, as well as being immune to corrosion and easy to connect. Their integrity is controlled by the fume thermostat > Suitable for installation in particularly harsh climates, thanks to the condensate collection device which protects the air pressure switch from humidity > Connection to solar thermal systems : set up for the production of domestic hot water combined with solar panels > IPX5D protection index, which means excellent electrical protection of the luminaire against the intrusion of liquids and foreign bodies Boiler control The DIVACONDENS control box consists of an easy-to-use interface with a backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. Main components Condensate trap Protects the air pressure switch from external humidity Recovery unit with condensate drain Steel frame Made with high precision automated processes. Incorporates an 8 liter expansion tank Copper central heating primary exchanger , protected by a non-toxic aluminum coating Burner Made of AISI 304 stainless steel ramps. Modulation takes place both in heating and in the production of domestic hot water High efficiency circulator , for heating and exchange with the DHW circuit High efficiency domestic hot water exchanger , for heating and exchange with the domestic hot water circuit Optimize comfort and savings "ROMEO" timer control The Romeo remote control allows control and setting of the boiler functions directly from the room in which it is installed. Comfort programming is possible on a weekly basis and also includes the 'holiday' function. Romeo is available with wired or wireless connection. The ROMEO modulating function allows boiler output to be modulated as the set room temperature value is reached. This improves the quality of comfort by eliminating heat peaks with consequent energy savings. Solar circuit integration Sun Easy function DIVACONDENS boasts electronics that simplify integration with thermal solar systems, both with natural and forced circulation. The microprocessor controls the temperature of the water coming from the solar circuit through the domestic hot water sensor and turns on the burner only if necessary. In case of insufficient irradiation and therefore a modest pre-heating of the domestic water, the boiler will contribute with the heat necessary to reach the required setpoint temperature If the sun and the solar system fulfill their "duty" no integration by the boiler will be necessary, the hot water will be conveyed to the tap, without the need for additional devices, with the mixing of the thermostatic valves. To reach the desired temperature, SUN EASY allows considerable savings even during the coldest seasons, exploiting and integrating even the smallest solar contribution, otherwise lost. Safety and comfort Functions Antifreeze In the event that the temperature in the boiler drops to 5°C, the burner ignites automatically and the circulator is activated in order to protect the appliance from damage caused by freezing. This function is active with the boiler powered by the gas circuit and under electrical voltage Post-circulation This function makes it possible to recover all the heat supplied by thermal inertia of the exchanger and transfer it to the heating system, and consequently to the rooms to be heated. This is a timer function and is active after the burner goes out in heating mode. Opentherm The DIVACONDENS electronic board adopts the Opentherm protocol. It allows the integration of other peripheral control units, such as, for example FZ4 - multi-zone manager - or Romeo - remote timer control. In fact, the Opentherm standard has been specially designed to share the logic and operating algorithms of the boiler with other additional control units. As a digital protocol, it allows total integration between the boiler and the satellite, with full control of the functions from the boiler and similarly from its satellite Product Guarantee : All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€580,00
-
Ferroli Ferroli Bluehelix Tech 25c LPG Condensing Boiler Complete With Smoke Exhaust Kit
IN THE ABSENCE OF THE PRODUCT, THE NEW MODEL BLUEHELIX RRT C 24 WILL BE SUPPLIED. IT CAN BE VIEWED AT THIS LINK: https://www.climaconviene.it/it/caldaia-a-gas-ferroli-bluehelix-tech-rrt-24c-metano-o-gpl-completa-di-kit-scarico-fumi-new/ Technical features Model : Bluehelix Tech 25C Power supply: LPG Energy rating Heating energy efficiency class: A DHW energy efficiency class: A Space heating energy efficiency : ηs 94 % Thermal range Minimum : 5.8 kW Maximum heating : 25.0 kW Maximum DHW : 27.5 kW Thermal power 60°C ~ 80°C Minimum : 5.7 kW Maximum heating : 24.5 kW Maximum DHW : 27.0 kW Thermal power 30°C ~ 50°C Minimum : 6.2 kW Maximum heating : 26.5 kW Useful efficiency 60°C ~ 80°C Minimum : 97.8% Maximum : 98.0 % Useful efficiency 30°C ~ 50°C Minimum : 106.1% Maximum : 107.5% Load reduced 30% : 108.8% Domestic hot water production ∆t 25°C : 15.5 l/min ∆t 30°C : 12.9 l/min Heating operating pressure Minimum : 0.8 bar Maximum : 3 bars Dimensions and weight Dimensions (HxWxD): 600x400x320 mm Empty weight: 28.0 kg Bluehelix Tech Wall mounted condensing, instantaneous or heating only boilers Efficiency, rationality and sturdiness. Recognized The range of generators is equipped with the new AISI 316 TI stainless steel exchanger. Designed and built according to the new ErP directives for eco-compatible design and labelling, Bluehelix Tech is at the top of its category. Bluehelix Tech achieves one of the highest energy efficiency of space heating in its category: ηs 94% . Furthermore, when combined with the external probe and the Romeo remote timer control, it reaches system energy class A+. Components The exchanger Ferroli has directed its research and design towards an exchanger that is simple and robust in its structure, using first-rate materials The exchanger consists of a simple spiral, without joints or welds. The generous section of the pipes allows a free, wide passage of the system fluid. The serpentine shape contrasts the deposit of impurities. The tube bundle is unique, without further parallel circuits. Since it is not a collector type exchanger, it is impossible for air bubbles to remain in the meanders of the circuits. Furthermore, any chemical washing of the boiler will take place effectively, as there is no possibility that the descaler pump pushes through a free circuit rather than a clogged one The tube that makes up the Bluehelix Tech exchanger is made of AISI 316 Ti stainless steel. It is a so-called austenitic alloy, particularly resistant to corrosion, enriched with the addition of titanium. it is also a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits The circulator distribution in class A Regulation 622/2012 provides that all boilers placed on the market from 1 August 2015 are equipped with a low-consumption circulator, otherwise defined as "class A". It is a decision that starts from the consideration of the enormous energy expenditure of the pumps and circulators installed in the various applications. In practice, i.e. by analyzing the impact of the low-consumption circulator integrated in the boiler, it reduces up to 30% of the total electricity consumption of the generator Self-adaptive The low-consumption circulator installed in the Bluehelix Tech has a variable flow rate, with ΔT control. The advantages offered are many, including: Cold system start-up: faster start-up with full control of the thermal load on the components Long-lasting maintenance of the temperature equilibrium conditions, once the set point has been reached Better operation in limit conditions, for example at minimum power, reduction of on-off states Reactivity to variations in the thermal load, an appreciable quality in multi-zone systems Robust Others are the merits attributable to the circulator chosen for Bluehelix Tech: The PWM signal (pulse width modulation) to the circulator allows extremely rapid intervention times to complete an advanced and complete electronic platform. This results in a drastic reduction of the ON-OFF events of the burner and the circulator. Electronic control of the drive torque at start up with consequent reduction of the risk of blocking. The routine anti-seize cycle is in any case carried out every 24 hours of inactivity. Self-protection function in case of overheating. Less noise Boiler control Control panel and functions The BLUEHELIX TECH control and management electronics allow the user to customize the operation of the appliance in order to manage the environmental comfort according to one's needs. The key control panel and the simple LCD display make the programming operations for the production of hot water, both for domestic hot water and for heating, extremely easy and intuitive. The remote control ROMEO Chronocontrol The BLUEHELIX TECH control and management electronics allow the user to customize the operation of the appliance in order to manage the environmental comfort according to one's needs. The key control panel and the simple LCD display make the programming operations for the production of hot water, both for domestic hot water and for heating, extremely easy and intuitive. With ROMEO you can: Adjust the heating and DHW temperatures Know the operating status of the boiler View the temperatures inside and outside the house Restart the boiler in case of temporary lockout Program the daily or weekly environmental comfort Activate/deactivate the heating function via the telephone The ROMEO modulating function allows boiler output to be modulated as the set room temperature value is reached. This improves the quality of comfort by eliminating heat peaks with consequent energy savings Guarantee : All the products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€833,00
-
Ferroli Ferroli Bluehelix Pro Rrt 32 CA Boiler Methane Or LPG Condensation Complete With Lox Nox Fume Exhaust Kit 0t3b3iwa - New
ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli BLUEHELIX PRO RRT 32 C methane or LPG condensing boiler Complete with Lox NOx Fume Exhaust Kit - NEW Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XXL Class A Characteristics of heating/DHW operation: Thermal power 80°C-60°C Max Heating: 30 / 6,3 kW Thermal power 50°C-30°C Max Sanitary: 32.5 / 6.9 kw Useful thermal efficiency 30%: 109.5 Max working pressure heating bar 3 NOx class 6 Sanitary flow rate ∆t 25°C 18.3 Protection degree (IEC 60529) IP X5D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x320 BLUEHELIX PRO RRT The quality of the BLUEHELIX line is unquestionable, and Ferroli is ready to put it to the test by offering its customers extended warranty coverage which also ensures periodic maintenance and statutory checks > STRONG POINTS: - With attention to aesthetics and silence, it continues the tradition of appreciation of the previous "Bluehelix Pro" series - DUAL STAINLESS STEEL exchanger : boiler with primary exchanger for heating and domestic hot water in very thick stainless steel integrated in a single component (DUAL). High efficiency even during DHW operation (94%). - Increased hydraulic passages of the exchanger both on the heating circuit and on the DHW circuit. - : in combination with the modulating remote control and the external probe (optional) it reaches the upper efficiency class A+ (scale from G to A+++) - MC2 : Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) - MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits - Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace - Hydraulic connections covered by the boiler shell - Large backlit multifunction graphic display for easy and correct setting of the parameters - Standard by-pass > BENEFITS OF bluehelix PRO RRT C: - Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes - FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard - Designed to simplify and facilitate normal maintenance and cleaning operations - Predisposition for solar systems: prearranged for the production of domestic hot water combined with solar panel systems - STOP AND GO: it is possible to delay the ignition of the burner by activating it only in the face of real withdrawals of domestic hot water - 3-star certified comfort in sanitary manufacturing according to EN 13203 - Minimum polluting emissions (class 6 according to EN 15502-1) - Sliding temperature operation via optional external probe - Low consumption modulating heating pump (ErP Ready - Class A) - Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) - Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit - Free methane/LPG/propaneted air transformation when checking the product and activating the warranty, to be requested from the Authorized Assistance Center Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€903,00
-
Ferroli Ferroli Condensing Boiler Bluehelix Prima 24 C Complete With Methane Or LPG Fume Exhaust Kit - New
Ferroli condensing boiler Bluehelix Prima 24 C complete with methane fume exhaust kit - New Characteristics: Seasonal space heating energy efficiency class A Water heating energy efficiency class A Declared load profile XL Heating max / min heat input (Hs) kW 20.6 / 4.2 Max DHW heat input (Hi) kW 25 Efficiency 30% % 108.8 NOx emission class (EN 15502-1) - 6 Max working pressure heating bar 3 Min. heating operating pressure bar 0.8 Heating expansion vessel capacity 8 litres Max DHW working pressure bar 9 Sanitary flow rate ∆t 25°C l/min 14 Protection degree (IEC 60529) IP IPX4D Dimensions HxWxD 700x400x330 MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits Bluehelix Prima The range of generators is equipped with the tested heat exchanger in stainless steel. Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX PRIMA is at the top of its category. Top efficiency even on old systems (Replacements) The exchanger of the BLUEHELIX PRIMA thermal group compared to the more classic and widespread steel exchanger. The geometry of the exchanger to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the classic exchanger tends to block up much faster in the part in contact with the flame due to the reduced passage area of the fluid, in which a real barrier of deposits * is created which hinder the heat exchange and reduce the efficiency below the nominal values. Boiler with single circuit stainless steel primary exchanger without joints and/or welding, it maintains high efficiency even on old systems. MC2: Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits Instantaneous production of domestic hot water with dedicated plate domestic heat exchanger User interface with display and multifunction keys for adjusting and setting the parameters Standard by-pass Predisposition for solar systems: prepared for the production of domestic hot water combined with solar panel systems Minimum polluting emissions (class 6 according to EN 15502-1) Sliding temperature operation via optional external probe Low consumption modulating heating pump (ErP Ready - Class A) Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit The engine The pipe that makes up the BLUEHELIX PRIMA exchanger is made of AISI 304 stainless steel, a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits. Boiler control The control unit of BLUEHELIX PRIMA consists of an easy to use interface with backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. MC2 (Multi Combustion Control) The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). MGR Methane, LPG, Propane Ready Air Thanks to the new electronics supplied, the gas change operation is extremely simple. The MC2 combustion control performs constant monitoring of the quality of the combustion and by simply modifying a parameter on the electronic card (operation to be carried out only by qualified personnel) it is possible to operate the boiler on Natural Gas or LPG or Propane Air. It is therefore not necessary to purchase additional accessory kits. Easy Maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the BLUEHELIX PRIMA thermal unit allows maintenance to be carried out with maximum precision and speed. Some examples: The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. Easy access to the burner unit by removing 4 screws and the quick coupling (clip) of the fan. The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front Sun Easy function BLUEHELIX PRIMA has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. By means of a sensor located on the DHW circuit, it continuously controls the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. Stop and Go function BLUEHELIX PRIMA has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. By means of a sensor located on the DHW circuit, it continuously controls the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. External installation Antifreeze function To make the most of the available space, the new BLUEHELIX PRIMA 24C boiler can be installed recessed into the wall thanks to the special kit; for more critical installations, in completely uncovered places not protected from atmospheric agents, the "painted cabinet" kit is also available. In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. ECO-COMFORT Sanitary function In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable. The efficiency and the load profiles according to the ErP directive are at the top of the category: mod. 24 C / A - XL Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€719,00
-
Ferroli Ferroli Condensing Boiler Bluehelix Alpha 28c Complete With Methane Or LPG Fume Exhaust Kit Cod. 0tpf4awa
ATTENTION Methane, LPG, Propane air Ready through a simple configuration the boiler is able to operate on methane, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli condensing boiler Bluehelix Alpha 28C complete with methane or LPG fume exhaust kit cod. 0TPF4AWA Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating max / min heat input (Hs) kW 27.2 / 5.3 Max DHW heat input (Hi) kW 28.5 Max working pressure heating bar 3 Min. heating operating pressure bar 0.8 Heating expansion vessel capacity 8 litres Max DHW working pressure bar 9 Minimum DHW operating pressure bar 0.3 Sanitary flow rate ∆t 25°C l/min 14 Protection degree (IEC 60529) IP IPX4D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x250 Bluehelix Alpha .. More beautiful than "BEFORE" The new range of generators is equipped with the tested heat exchanger in stainless steel . Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX ALPHA is at the top of its category. TOP EFFICIENCY EVEN ON OLD SYSTEMS (REPLACEMENTS) mod. 24 C COMBINED (14 l/min at ∆t 25°C) The BLUEHELIX ALPHA thermal group exchanger (fig. A) compared with the more classic and widespread steel exchanger. This geometry allows the exchanger to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig. B tends to block up much faster in the part in contact with the flame due to the reduced passage area of the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values BLUEHELIX ALPHA FROM THE INSIDE EXCHANGER High flow single circuit stainless steel exchanger, resistant to clogging and easy to clean STEEL FRAME Made with high precision automated processes EXPANSION TANK 8 liter expansion tank placed on the side ELECTRIC PANEL FAN Offset fan, to facilitate maintenance of the primary exchanger without disassembly DOMESTIC HOT WATER EXCHANGER In stainless steel, with copper brazing CIRCULATOR High efficiency, for heating and exchange with the DHW circuit SEALED CHAMBER Removable steel panel to protect the combustion chamber with the function of a sealed chamber ELECTRICAL PANEL Large removable electrical panel to protect against water damage that may occur during normal maintenance. Easy access to electrical connectors. THE ENGINE The tube that makes up the BLUEHELIX ALPHA exchanger is made of stainless steel, a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits. THE BOILER CONTROL The control box of BLUEHELIX ALPHA consists of an easy to use interface with backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. MC2 The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). MGR Methane, LPG, Propane Ready Air The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). Thanks to the new electronics supplied, the gas change operation is extremely simple. The MC2 combustion control performs constant monitoring of the quality of the combustion and by simply modifying a parameter on the electronic card (operation to be carried out only by qualified personnel) it is possible to operate the boiler on Natural Gas or LPG or Propane Air. It is therefore not necessary to purchase additional accessory kits. CONNECT New wireless remote control available as an accessory for home comfort management also from a smartphone using the connect app (iOS and Android). Maximizes room comfort with delivery temperature modulation through the Room Climatic Compensation (CCA) and External Climatic Compensation (CCE) functions via the external temperature detectable directly from the internet (or from an optional external probe). It improves the average seasonal efficiency in space heating by +4%. EASY MAINTENANCE Problem-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the BLUEHELIX ALPHA thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: - The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - Easy access to the burner unit by removing 4 screws and the quick coupling (clip) of the fan. - The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. - The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. - Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front SUN EASY FUNCTION BLUEHELIX ALPHA has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. By means of a sensor located on the DHW circuit, it continuously controls the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. STOP AND GO FUNCTION With the use of sanitary mixing taps, short or very short dispensing for quick rinses involves the start of the boiler ignition procedure which usually ends immediately. The continuation of these "false starts" can, in the long run, compromise the average life of the product. For this reason BLUEHELIX ALPHA provides an electronic parameter through which it is possible to delay burner ignition (Stop and Go) by activating it only in the face of actual withdrawals of domestic hot water. OUTDOOR INSTALLATION - ANTIFREEZE FUNCTION To make the most of the available space, the new BLUEHELIX ALPHA 24 - 28 C boiler can be installed recessed into the wall thanks to the special kit; for more critical installations, in completely uncovered places not protected from atmospheric agents, the "painted cabinet" kit is also available. In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. SANITARY ECO-COMFORT FUNCTION In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable. The efficiency and the load profiles according to the ErP directive are at the top of the category: mod. 24 C / A - XL. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€759,00
You have seen 60 out of 74 products