IMMERGAS VICTRIX TERA 28 kW CONDENSING COMPLETE WITH FUME EXHAUST KIT - NEW ErP Technical features Product code: 3.027369 Energy label specifications according to the European ErP directive Heating energy efficiency Class Sanitary Energy Efficiency Class Withdrawal profile: XL Characteristics of heating/DHW operation: Maximum nominal heat input in DHW kW 32.6 Maximum nominal heat input in heating kW 28.6 Useful thermal efficiency at 30% of the nominal load. (80 / 60 °C) % 97.9 Specific flow rate in continuous domestic hot water service (∆t 30 °C) l/min 15.3 Nominal heating expansion vessel capacity (total) liters 10 (6.4) Electrical protection degree IP X5D Boiler weight full of water (empty) kg 37.9 (35.5) VICTRIX TERA Everything you need, immediately and in a small space It is the new line that strengthens the Immergas range with boilers dedicated to those looking for quality and simplicity. All the appliances are condensing and above all with total premixing to save gas efficiently. The dimensions are compact and the easy placement allows flexibility to adapt to new installations or to replace existing appliances in the home, outdoors in protected places, recessed with OMNI CONTAINER. There are two instantaneous versions - 24 and 28 kW - and one for heating only of 24 kW which can be combined with boilers of various capacities. The entire range you find is equipped with a condensing module with stainless steel coil and designed to comply with the new European Directives on the use of energy. VICTRIX TERA boilers fall into class 6, the most ecological in the European classification, for low emissions of carbon monoxide (CO) and nitrogen oxides (NOx). All versions can discharge the fumes on the wall in the cases envisaged by DL 102 of 4 July 2014. The controls are simple, the LCD display is clear and the selection buttons for adjustments and settings are activated quickly. Features and strengths: Low consumption: the low consumption circulator allows for considerable savings in electricity. Standard: the cover of the water connections improves the aesthetics in domestic environments. Comfort Ease of use: practical buttons and a backlit display allow you to easily manage and view the boiler setting. DOMINUS App: simple and intuitive, it allows you to check the functioning and temperature of the boiler, turn it on and off from anywhere via smartphone or tablet. Options. Environmental compatibility Eco-friendly technology: complies with the European ErP and ELD Directives, allows you to achieve high energy efficiency classes in heating and hot water production. Ecological class 6 (European Standards UNI 297 and 483): the best for reduced emissions of nitrogen oxides (NOX). Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Characteristics: Class A heating energy efficiency Sanitary energy efficiency Class A Sanitary load profile: XL Heating / domestic hot water nominal heat input kW 20/28 Heating / domestic hot water reduced heat input kW 2.80 Supply voltage/frequency: 230/50 Volt/Hz NOx Class 5 Supply voltage / frequency Volt/Hz 230/50 Boiler dimensions (HxLxP) mm 780x400x365; 36 Gas version available: METHANE Warm-up exercise: Maximum pressure and temperatures bar / °C 3 / 90 Expansion vessel capacity 9 litres Healthcare exercise: Minimum / maximum pressure 0.2 - 6 bar Quantity of hot water with Δt =25° litres/min 16.1 Minimum domestic water flow rate litres/min 2 To view further technical information on the product CLICK HERE The new MySMART condensing boiler is designed following the ecodesign indications provided for by the European ErP Directive. MySMART has a higher power in DHW mode thus offering greater comfort. The boiler, an instantaneous combined model, offers as standard the new front access condensing exchanger with improved efficiency (94% seasonal efficiency) and the low consumption FLEX modulating circulator with modifiable head up to 7m. MySMART is compatible with the new Ø 50 mm flue with which it is possible to carry out ducting up to 7m. The BeSMART Comfort Control is inserted as standard with MySMART with the WiFi Box, the external probe, the flue splitter, the plumbing fittings cover, the template, the heating taps with filter, the brass plumbing fittings, the gas taps and sanitary. It forms a class A + system without the addition of options BeSMART WiFi Comfort control included as standard Available APPs for management from Smartphone and Tablet Very high modulation (up to 1:10) Flex low consumption circulator (EEI ≤ 0.20 ) with 6m head adjustable to 7m Possibility of ducting with the special flue in PP Ø 50 Standard ø 80 mm splitter General characteristics BeSMART the advanced comfort control Leaving for your home in the mountains? Or returning from a business trip? Through your Smartphone or Tablet, with the BeSMART App you can turn the boiler on and off, read the home and outside temperature and change the time programming of your heating system. The BeSMART WiFi Comfort Control Panel, standard in the MySMART boiler, is the remote boiler management device with chronothermostat functions. With the WiFi Box kit (series) it is possible to manage comfort even remotely with a Smartphone and Tablet. Simple and intuitive, it allows you to adjust the parameters and activate the many functions on the boiler. A large liquid crystal display shows all important information. Using the keys, the temperature of the heating water and domestic hot water is set easily and intuitively and the time programming is carried out. MySMART also features the Easy Climate function (thermoregulation with standard external probe). MySMART, the elegant The new MySMART boiler is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to easily select all the functions necessary for using and setting the boiler. OTHER CHARACTERISTICS: Telemanagement : Remotely, with BeSMART, you can turn the boiler on and off, change the temperatures, program the weekly chronothermostat, view the home temperature. Management with tablets and smartphones : Compatible with smartphones and tablets using the Android (≥ 3.0 ver.) or iOS system. Downloadable Apps: Available APPs compatible with Android (≥ ver. 3.0) and iOS systems for switching on/off and managing boilers/systems remotely via Smartphone and Tablet. WiFi : WiFi communication between the WiFi Box and the home ADSL WiFi modem router to connect to the internet. Possibility to connect to the optional WiFi modem kit for SIM CARD as an alternative to the ADSL modem. RF : RF (radio frequency) communication between the BeSMART Comfort Control and the WiFi Box; Possibility of connecting up to 8 BeSMART Comfort Controls in RF to manage up to 8 different zones/environments (wireless communication up to 40 m away). Weekly heating time programming : Heating time programming in 30 minute intervals and possibility to choose between different pre-set programs. Holiday function: For quick entry of the number of holiday days in which to operate the generator in order to have a reduced room temperature. The acronym ErP, an acronym for "Energy related Products", identifies Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015, the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class. Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility of easily identifying the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual devices. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with a nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Beretta's commitment is concrete and is directed towards an increasingly eco-sustainable future. This is why Beretta is already ErP-Ready today with solutions for any installation and comfort requirement linked to autonomous residential and centralized systems. A complete and constantly evolving catalog with many ErP-Ready proposals in the case of mere replacement, energy redevelopment, renovation or new construction. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

RIELLO RESIDENCE CONDENS 28 KIS LPG CONDENSING BOILER COMPLETE WITH FUME KIT - NEW ErP Technical features Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input:+ 25 kW Sanitary nominal heat input: 28 kW Energy efficiency (92/42/EEC) **** Useful efficiency Pn (50°/30°): 104.7% Profit return 30% (47th return): 107.8% Sealed chamber, forced draught Quantity of hot water with Δt 25°C: 16.1 l/min Dimensions (hxlxp) mm 845 x 400 x 358 ; 39 kgs Electrical protection degree: IP X5D NOx class: 5 Power supply: LPG. General characteristics RESIDENCE CONDENS Yield **** Low polluting emissions. Aluminum condenser, with premix burner. Heating only models and combined models. Residence Condens is the Riello wall-mounted condensing boiler for medium-sized users. The new primary heat exchanger completely made of aluminum with front access to the combustion chamber ensures better efficiency and durability. It is available with powers from 20 to 32 kW.   Modulation ratio 1:8 which allows the boiler to respond to all heat requests. Self-modulating circulator, low consumption (IEE≤0.20). "Winter with Pre-heating" function: allows the DHW exchanger to be kept at the right temperature, reducing waiting times during withdrawal (instantaneous combined models only). Standard thermoregulation on the card in combination with the external probe (optional). Assembly template, hydraulic fittings, power supply cable supplied. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

IN CASE OF NON-AVAILABILITY OF THE PRODUCT, THE NEW MODEL baxi evolution prime 30 WILL BE SUPPLIED Technical specifications ErP energy efficiency class (heating and DHW): A - A Load profile: XL heating and instant DHW production Heating/sanitary nominal heat inputkW 28.9/24.7 Sanitary nominal thermal powerÿkW 28ÿ Energy efficiency(92/42/CEE)ÿ**** Efficiency 100% Pn (80-60øC): 97.8% Efficiency 100% Pn (50-30øC): 105.0% Minimum operating temperatureøC -5 Expansion/pre-charge capacity l/bar 8/0.5 Sanitary water temperature adjustmentøC 35-60 Sanitary water production T 25øC l/min 16.1 Minimum domestic hot water flow rate I/min 2ÿ Degrees of protection: IPX5Dÿ NOx class (EN 483) 5 Electric power W 155 Dimensions (hxwxd): 700x395x279ÿmmÿ; 44 kgs Power supply: METHANE LPG Main features First ÿThe ideal condensation for replacement in old systemsÿ with cast iron / lamellar steel radiators The new Prime condensing range is divided into two models, 24 and 28 kW for heating and instant domestic hot water production. Prime was designed in compliance with the requirements of the Ecodesign and Labeling Directives. The labeling directive (2010/30/EU) requires the labeling of products according to a decreasing energy scale that goes from A++ to G starting from 09/26/2015 and from A+++ to D from 09/26/2019. The label was created to allow the final consumer, by providing real and comparable data, to make informed choices by targeting high-efficiency products. Characteristics: Easy to use thanks to the control panel with knobs and backlit LCD displayÿ Easy installation thanks to the ultra-compact dimensions (700x395x285mm - including knobs) and weight-free (26 kg)ÿ Campdi modulation 1:5 greater efficiency and silence High efficiency circulation pumpÿ Arrangement for combination with the Baxiÿ integrated solar system Double 80 exhausts as standardÿ Connection of 50 mm rigid flexible exhaust pipes: solutions for flue refurbishmentÿ Connect pressurized collective fluesÿ Boilers working with methane that can be transformed into LPG and propane by means of a specific regulation (conversion kit not necessary) The advantages of the new Prime Easy to install The ultra-compact dimensions 700x395x279 mm and the weight of just 26 kg reduce the installation time. The new Prime has the same distance between centers of the hydraulic connections of the conventional BAXI boilers to be replaced. The frontal access to the electrical connection also speeds up connection times. The fixing bracket supplied as standard and the visible hooks facilitate wall mounting Clapet (non-return valve) Included in the downstream duct of the gas group fan ÿConnection of pressurized collective flues Thanks to the integrated non-return valve (clapet), Prime is designed for connection to pressurized collective flues. ÿFlexible smoke ducts 50 mm Possibility of rehabilitating the flue pipes with a 50 mm discharge hose (up to 40m of discharge). Less energy consumption Thanks to the condensing technology, the high efficiency pump and the series of modulating room thermostats available as an accessory. The new regulation 7129-3:2015 prescribes the possibility of creating collective flues in positive pressure only for type C condensing appliances. It is possible to connect to a collective flue in positive pressure only appliances declared suitable by the manufacturer for this application and equipped with non-return device (clapet), designed to prevent the combustion products from flowing through devices connected and temporarily switched off; the smoke non-return valve is an integral part of the appliance Flexibility in replacement Easy replacement of old standard boilers, thanks to the central flue and separable flue supplied as standard The 60/100 axial exhaust is available as an accessory and can be combined with a 90ø diameter 60/100 curved tube extension (adjustable by 360ø). To facilitate replacement in installations where spaces are limited (flue gas outlet at the rear of the boiler), the new accessory is available with a lowered coaxial bend 90ø. The lower closure kit allows the boiler to adapt to any environment, reducing the visual impact by fitting into all replacement installation contexts. To facilitate replacement in installations where space is limited (flue gas outlets at the rear of the boiler), the new 90ø coaxial lowered bend accessory is available New combustion group The new Prime combines the performance of the stainless steel exchanger with the advantages of a new generation burner integrated with an innovative cold closing door. The new cylinder burner ensures greater thermal-acoustic comfort, and reduced NOx and CO emissions thanks to the greater flame stability. The new cold door reduces losses by 75% with a surface temperature below 20°C, guaranteeing significant savings in stand-by and during operation, speeding up maintenance, as there is no need to wait for it to cool down. All ready for Energy Labeling What is it about From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. It's about me tooÿ YES, it affects everyone: professionals and end users The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier's responsibility The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. Responsibilities of Resellersÿ First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features ErP energy efficiency class (heating and DHW): A  Load profile: XL Nominal heat input 28.9 kW Nominal thermal power 28 kW Energy efficiency (92/42/EEC) **** Nominal efficiency 80/60°C % 97.6 Return at 30% % 108.8 Heating circuit water temperature control °C 25-80 Sanitary water temperature adjustment °C 35-60 Sanitary water production ∆T 25°C l/min 16.1 Minimum domestic water flow rate: 2 l/min Minimum operating temperature: -15°C Expansion/pre-charge vessel capacity l/bar: 8/0.8 NOx class (EN 483): 5 Electric power W 99 Degree of protection IPX5D Dimensions (hxlxp) - with case: mm 1170 x 600 x 245 Dimensions (hxwxd) - boiler 770 x 470 x 238 mm; 32.5kg Power supply: METHANE Luna Duo-Tec IN+ The efficiency of compact built-in comfort Baxi has always offered the ideal system solution for any type of home: for this reason the Duo-tec+ range is expanding with built-in models and for outdoor installation. Luna Duo-tec IN+ is the built-in condensing boiler, specifically designed to make it suitable for replacing an old built-in generator but also in new installations. The extremely compact dimensions of the boiler facilitate its installation in small/medium-sized apartments, and in general in all housing units where efficient space management is an important objective (for example in technical rooms or in the presence of ) Recessed installation outdoors Luna Duo-tec IN+ is the built-in condensing boiler, specifically designed to make it suitable for replacing an old built-in generator but also in new installations. The extremely compact dimensions of the boiler facilitate its installation in small/medium-sized apartments, and in general in all housing units where efficient space management is an important objective (for example in technical rooms or in the presence of ). The packing contains the bracket and installation fittings for inserting the boiler into the containment case Characteristics: Wide modulation range up to 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control Automatic plant loading system Minimum operating temperature: -15°C Remote digital control panel with LCD display Arrangement for combination with the Baxi integrated solar system High efficiency circulation pump with total modulation Ultra-compact dimensions: 770x470x238 mm (boiler) STANDARD installation kit (gas cock / gas inlet / telescopic fittings) Antifreeze function and IPX5D degree of protection Digital control panel The Duo-tec+ range of boilers is equipped with a digital control panel with backlit LCD display, easy to use thanks to dedicated and independent keys to adjust the temperature of the domestic hot water and the heating. The display allows you to view all the information and set the operating parameters in a clear and immediate way. Gas Adaptive Control The innovative GAC ( Gas Adaptive Control ) automatic combustion control system guarantees a wide modulation range up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adjust the thermal power produced to the actual power dissipated from the building avoiding excessive heating/cooling of the building. Antifreeze function The boilers have been designed to allow the boiler to operate down to -15°C. Furthermore, the antifreeze function provides for the automatic ignition of the burner, avoiding freezing phenomena. Wide modulation range 1:7 greater efficiency given by less switching on and off: with a high modulation ratio, the reduction of continuous switching on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions adjustment of the thermal power produced to the power dissipated thus avoiding excessive overheating/cooling of the premises Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Energy label specifications according to the European ErP directive Class B heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating max heat input kW 28.0 Nominal thermal power kW 27.0 Efficiency Pmax (80/60°C) % 103.5 Directive efficiency class 92/42 EEC **** Max. heating operating pressure bar 3 Heating pressure min. bars 0.8 Domestic hot water production: -Δt 25°C: 15.7 l/min -Δt 30°C: 13.0 l/min Sanitary working pressure Max: 9 bar Dimensions WxHxD mm 700x400x320 mm Power supply: LPG *NB: ALSO OPERATES ON LPG WITH THE USE OF A SPECIAL CONVERSION KIT TO BE REQUESTED FROM THE AUTHORIZED SERVICE CENTRE. General characteristics DIVACONDENS F28 D DIVACONDENS D is the condensing heat generator for traditional heating systems. The tried and tested Ferroli technology in the field of traditional wall mounted boilers has been enriched by increasing the performance of the product in the simplest way, with the use of a robust recuperator which preheats the primary circuit using the residual heat of the exhaust fumes. ADVANTAGES Robust post-condenser powered by the closed circuit of the primary circuit, i.e. without the inlet of external mains water. The heat exchange with the fumes takes place inside large diameter water passages. Generator with simple and rational operation Condensate collection device to protect the air pressure switch, for regular combustion even in the presence of very cold external temperatures ECO function in DHW for greater savings in the period of low use of hot water Predisposition for solar systems: prepared for the production of domestic hot water combined with solar panel systems Place of installation: also for outdoors in a partially protected place down to -5°C as standard Certified operation also with propane air (50% air – 50% G31) by means of a specific transformation to be requested from the Authorized Assistance Center (max total price of 30 euros + VAT) Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre. Free transformation during product verification and activation of the guarantee only if the specific code running on LPG is not available. THE BOILER CONTROL The control box of DIVACONDENS D consists of an easy to use interface with a backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. MAIN COMPONENTS RECOVERY UNIT/HYDRAULIC DIAGRAMS FUME THERMOSTAT It preserves the integrity of the polypropylene pipes and, together with the air pressure switch, constitutes a double safety device for the evacuation system. OPTIMIZE COMFORT AND SAVINGS ROMEO TIMER (optional) The Romeo remote control allows control and setting of the boiler functions directly from the room in which it is installed. Comfort programming is possible on a weekly basis and also includes the 'holiday' function. Romeo is available with wired or wireless connection. The ROMEO modulating function allows boiler output to be modulated as the set room temperature value is reached. This improves the quality of comfort by eliminating heat peaks with consequent energy savings. HIGH EFFICIENCY CIRCULATOR EU regulation 622/2012 establishes that all boilers introduced on the market from 1 August 2015 must be equipped with a high-efficiency circulator (technically speaking, with an EEI, energy efficiency index ≤ 0.23). This decision was taken following the enormous energy consumption of all pumps and circulators installed in different applications in Europe. In practice, a high-efficiency circulator - incorporated in the boiler - reduces up to 30% of the total electricity consumption of the boiler itself. ONE CENT PER HOUR If we consider the maximum consumption of the pump mounted on the Divacondens D (0.04 kWh) compared to the previous circulator (0.085 kWh) we will save almost a euro cent for each hour of operation (electricity cost €0.19/kWh). Let's therefore multiply this tiny value by each hour of operation of the circulator in a year (for example 2,500 hours, for a moderately cold climate) ... €21.40 will be the annual saving if we replace an old boiler, and therefore also a old circulator, with Divacondens SUN EASY FUNCTION DIVACONDENS D boasts electronics that simplify integration with thermal solar systems, both with natural and forced circulation. The microprocessor controls the temperature of the water coming from the solar circuit through the domestic hot water sensor and switches on the burner only if necessary. In case of insufficient irradiation and therefore a modest pre-heating of the domestic water, the boiler will contribute with the heat necessary to reach the required set point temperature. If the sun and the solar system fulfill their "duty" no integration by the boiler will be necessary, the hot water will be conveyed to the tap, without the need for additional devices, with the To reach the desired temperature, SUN EASY allows considerable savings even during the coldest seasons, by exploiting and integrating even the smallest solar contribution, otherwise lost by mixing the thermostatic valves. FUNCTIONS ANTIFREEZE In the event that the temperature in the boiler drops to 5°C, the burner ignites automatically and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. POST-CIRCULATION This function makes it possible to recover all the heat supplied due to thermal inertia of the exchanger and transfer it to the heating system, and consequently to the rooms to be heated. This is a timer function (customizable duration) and is active after the burner goes out in heating mode. OPERATION IN SLIDING TEMPERATURE With the installation of the “External probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. EASY CONTROL The electronic board of DIVACONDENS D adopts the Opentherm protocol. It allows the integration of other peripheral control units such as, for example, the ROMEO remote timer control. In fact, the Opentherm standard has been specially designed to share the logic and operating algorithms of the boiler with other additional control units. As a digital protocol, it allows total integration between the boiler and the satellite, with full control of the functions from the boiler and similarly from its satellite. Product Guarantee: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Seasonal heating efficiency % 93 Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 25/29 kW Nominal heating thermal power: 24.45 kW Efficiency at rated power: 97.8% Efficiency at reduced load (30%): 102% Max electric power heating Watt 78 Electrical protection degree IP X5D Expansion tank capacity 8 litres Quantity of hot water with Δt=25°C: 17 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 715x405x248 ; 29kg LPG power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionization control). Exclusive services: Beretta offers 5 years of peace of mind thanks to the Kasko warranty extension formulas. To view more product information CLICK HERE General characteristics HELLO GREEN ErP Ciao Green: high energy efficiency, low gas consumption and low emissions. The entry into force of the European ErP Directive (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Mandatory labeling provides greater transparency on the characteristics of products that can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2) by 20%, increasing by 20% the use of renewable energies and reduce energy consumption by 20% in EU countries. Condensing exchanger The innovative Beretta compact aluminum condensing exchanger is assembled with a brazing production process in a controlled atmosphere. In addition to allowing a more uniform distribution of heat, aluminum offers a high resistance to corrosion for the benefit of a longer duration over time. Aluminum is also chosen for its lightness, excellent conductivity, mechanical strength, reliability and recyclability. The condensing exchanger makes it possible to recover a large part of the heat from the fumes by reducing losses in the chimney, and a large part of the latent heat, reaching a four-star energy efficiency value (according to European Directive EEC 92/42). The premix burner optimizes the combustion mixture by reducing NOx emissions to values ​​that place the boiler in Class 5, the highest according to the European Directive EN 677. Universal installation Ciao Green is designed to be installed outdoors in partially protected places or recessed thanks to the dedicated accessories and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit together with the siphon antifreeze heater kit. If the boiler is installed outside, without embedding, the lower cover is required for greater protection. The management The electronic panel is the brain of boiler management. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. A liquid crystal display and LEDs provide information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. Characteristics: ErP boilers with synchronous modulating pump with low energy consumption (EEI≤0.20) Designed according to the ecodesign indications provided for by the European ErP Directive Energy Class > heating (class A) > DHW profile XL (class A) Seasonal heating efficiency 93% Aluminum condensing exchanger, two versions of 25 kW and 29 kW combined and one 25 kW heating only Designed following the ecodesign indications of the European ErP Directive Class 5 according to the UNI EN 483 European Standard It can also be installed externally and recessed through the adoption of special kits (optional) Display for viewing temperature and diagnostic codes IPX5D electrical protection degree Prepared for connection to the remote control (optional) Standard thermoregulation (optional external probe) Plumbing fittings, gas and sanitary taps (optional) Antifreeze kit available up to -10°C (optional) Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations simultaneously issued for the energy labeling of products will also become effective in addition to the corresponding Directive 2010/30/EU. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual devices. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with a nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview BIASI PARVA RECUPERA E 28S LPG CONDENSING BOILER - NEW ErP 2015, SEALED CHAMBER COMPLETE WITH FUME EXHAUST KIT: PARVA Recupera E the ErP condensing boiler with heat recovery unit Technical specifications Model:ÿPARVA Recover E 28S Product number:ÿ10313.2027.3 Energy label specifications according to the European ErPÿ directive Class B heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Thermal input:ÿ29ÿkW Rated useful power: 28.4 kW Nominal load efficiency:ÿ98% Efficiency minimum load:ÿ95.8% Energy efficiency stars: (dir 92/42/CEE) **** Min/max heating temperature: 38/85ÿøC Capacity of the expansion vessel: 6 lt Sanitary flow rate t =25øK l/min: 16.3 l/min Degrees of protection for the electrical system:ÿIPX4D Extremely compact dimensions hxwxd: mmÿ803x400x350ÿ; 49kg LPG fuel supply Features list ErP wall-mounted boilers with recuperator Redeveloping an old thermal systemÿ Biasi has designed the ÿPARVA Recupera NOx EÿandÿPARVA Recupera Eÿboilers to replace traditional boilers in old systems. The PARVA Recupera boilers by Biasi are equipped with a corrosion-resistant aluminum alloy fume recovery unit which makes these boilers particularly solid. The recovery unit is made of aluminium, has a finned coil which determines a large exchange surface and is equipped with a device to ensure that the boiler discharges the condensate correctly. The recuperator is treated with a Teflon coating process to ensure maximum durability over time. Thanks to the large exchange surface, the recuperator allows the recovery of thermal energy which would otherwise be dispersed outside through the hot fumes produced by combustion. PARVA Recover E PARVA Recupera E is the condensing boiler designed for traditional systems and easily adaptable to new floor-based systems using MULTIZONE, a hot water distribution system for heating. PARVA It recovers the traditional boiler in the regulations but it has clearly higher efficiency than the traditional boilers at the same operating temperature. As a condensing boiler, PARVA Recupera allows you to take advantage of the tax deduction according to current legislation. Characteristics: High yields (in compliance with yield directive 92/42 EEC and Legislative Decree 311/06ÿ Primary laminated copper heat exchanger with large double circulation exchange surfaceÿ Aluminum heat recovery unit to exploit the heat of the fumes and transfer it to the waterÿ Sanitary plate heat exchanger in INOXÿ steel High efficiency pump with low energy consumptionÿ retractable control panel, with ergonomic knobs and backlit displayÿ Electronic board for:ÿ - Re-ignition frequency adjustmentÿ - Adjustable primary circuit thermal inertia disposalsÿ - Selection of circulator modeÿ - Circulator anti-seizeÿ - Antifreeze safetyÿ - Chimney sweep functionÿ Integrated automatic by-passÿ Immunity to radio interferenceÿ Sanitary flowstat magneticÿ Absolute heating pressure switchÿ Degrees of protection IPX4Dÿ Possibility of integrating PARVA Recupera E with Biasi solar systems using the optional solar kit. Fiscal detraction As a condensing boiler, PARVA Recupera E allows you to take advantage of the tax deduction according to current legislation.ÿÿ Heat recoveryÿ The heat recovery recovers the heat from the fumes before they are expelled and preheats the water directed to the primary exchanger. The recuperator made of aluminum has a finned coil which determines a large exchange surface and has a device to ensure that the boiler discharges the condensate correctly.ÿÿ Thermoregulation By connecting the external probe (optional) directly to the boiler, you can access the climatic adjustment function. The boiler is equipped with a complete set of curves which can be accessed by entering programming. By simply turning a knob you choose the curve, PARVA recovers and will automatically adapt its operation to the external climatic conditions.ÿÿ High circulation primary heat exchangerÿ It is the element that distinguishes the whole PARVA E Biasi range. It favors the flow of water into the heating system and, thanks to its reduced hydraulic resistance, adapts the boiler to the system, facilitating the transmission of heat to the radiators.ÿ Save simplicity of use Parva Recupera retains the simplicity of management, programming and regulation of the traditional boiler and imports the savings of the condensing boiler resulting from the recovery of heat from the fumes. The heat recovery unit preheats the system water with the heat released by the fumes, heat which in traditional boilers is dispersed into the environment. This recovery of energy from the fumes, at operating temperatures typical of radiator systems, leads Parva Recupera to have higher yields than traditional boilers. Low complexity, high comfort Parva Recupera boilers, despite the high technical content, are still very easy to use. Theÿcontrol panelÿhas two knobs dedicated to regulating the temperature of the domestic hot water and the heating water, the key to reset the boiler after the lockout status, the new display to view the boiler operating status and facilitate understanding by the User and the installer's settings . Fault diagnostics allow immediate verification of correct operation. The manometer allows you to check the system pressure while the temperature is shown on the display. Everything is hidden under a door that defines the sober and linear aesthetics of Parva Recupera. Included in delivery Boiler support bracket and paper templateÿ Condensate collection trapÿ Quick instruction to the user.ÿ All ready for Energy Labeling What is it about From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. It's about me too YES, it affects everyone: professionals and end users The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier's liability The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. Responsibilities of Resellersÿ First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

RIELLO START IN CONDENS 29 KIS LPG CONDENSING COMPLETE WITH FUME KIT + BUILT-IN UNIT - NEW ErP Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 25 kW Sanitary nominal heat input: 29 kW Energy efficiency (92/42/EEC) **** Useful efficiency Pn (50°/30°): 104.9% Profit return 30% (47th return): 108.4% Sealed chamber, forced draught Quantity of hot water with Δt 25°C: 16.6 l/min Dimensions (hxwxd) mm 792 x 405 x 248 ; 32 kgs Electrical protection degree: IP X5D NOx class: 5 It can be installed flush-mounted using the special built-in unit Power supply: LPG General characteristics START IN CONDENS Yield **** Low polluting emissions Aluminum condenser, with premix burner Recessed Start IN Condens is the new Riello condensing wall-mounted proposal for small and medium-sized domestic users. The new compact aluminum condensing exchanger guarantees efficiency and reduction of polluting emissions. It can be installed flush-mounted using the special kit. It is available in version 25 (with 25 kW of DHW power and 20 kW in heating) and 29 (with 29 kW of DHW power and 25 kW in heating). Characteristics: Low consumption circulator (IEE≤0.20) "Winter with Pre-heating" function: allows the DHW exchanger to be kept at temperature, reducing waiting times during withdrawal (can be activated by the user) Remote control panel in combination with the external probe (optional) Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Code : 20095435 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Seasonal heating efficiency % 93 Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 25/29 kW Nominal heating thermal power: 24.45 kW Efficiency at rated power: 97.8% Efficiency at reduced load (30%): 102% Max electric power heating Watt 78 Electrical protection degree IP X5D Expansion tank capacity 8 litres Quantity of hot water with Δt=25°C: 17 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 715x405x248 ; 29kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionization control). General characteristics HELLO GREEN ErP Ciao Green: high energy efficiency, low gas consumption and low emissions. The entry into force of the European ErP Directive (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Mandatory labeling provides greater transparency on the characteristics of products that can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2) by 20%, increasing by 20% the use of renewable energies and reduce energy consumption by 20% in EU countries. Condensing exchanger The innovative Beretta compact aluminum condensing exchanger is assembled with a brazing production process in a controlled atmosphere. In addition to allowing a more uniform distribution of heat, aluminum offers a high resistance to corrosion for the benefit of a longer duration over time. Aluminum is also chosen for its lightness, excellent conductivity, mechanical strength, reliability and recyclability. The condensing exchanger makes it possible to recover a large part of the heat from the fumes by reducing losses in the chimney, and a large part of the latent heat, reaching a four-star energy efficiency value (according to European Directive EEC 92/42). The premix burner optimizes the combustion mixture by reducing NOx emissions to values ​​that place the boiler in Class 5, the highest according to the European Directive EN 677. Universal installation Ciao Green is designed to be installed outdoors in partially protected places or recessed thanks to the dedicated accessories and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit together with the siphon antifreeze heater kit. If the boiler is installed outside, without embedding, the lower cover is required for greater protection. The management The electronic panel is the brain of boiler management. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. A liquid crystal display and LEDs provide information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. Characteristics: ErP boilers with synchronous modulating pump with low energy consumption (EEI≤0.20) Designed according to the ecodesign indications provided for by the European ErP Directive Energy Class > heating (class A) > DHW profile XL (class A) Seasonal heating efficiency 93% Aluminum condensing exchanger, two versions of 25 kW and 29 kW combined and one 25 kW heating only Designed following the ecodesign indications of the European ErP Directive Class 5 according to the UNI EN 483 European Standard It can also be installed externally and recessed through the adoption of special kits (optional) Display for viewing temperature and diagnostic codes IPX5D electrical protection degree Prepared for connection to the remote control (optional) Standard thermoregulation (optional external probe) Plumbing fittings, gas and sanitary taps (optional) Antifreeze kit available up to -10°C (optional) Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview RIELLO FAMILY AR 29 KIS LPG CONDENSING BOILER COMPLETE WITH FUME KIT - NEW ErP 2015: Family AR the new generation condensing boiler specifically designed to operate with high temperatures (delivery 80°C and return 60°C) and therefore in radiator systems Technical specifications Product code:ÿ20100511 Energy label specifications according to the European ErP directive Class B heating energy efficiency Sanitaryware energy efficiencyprofilXL Class A Characteristics of heating/sanitary exercises: Firebox thermal power (heating)ÿmin-max: 9.9ú29.0ÿkW Useful thermal power (sanitary) min-max: 9.9ú29.0ÿkW Energy efficiency(92/42/CEE)ÿ**** Efficiency useful at Pn* (50øC-30øC): 97.1% Profitability 30% (47ø return): 96.2% Sealed chamber, forced draft Quantity of hot water at t 25°C: 16.6 l/min Minimum domestic water flow rate: 2ÿl/min Dimensions (hxwxd) mmÿ845 x 450 x 332 ; 44 kgs Electrical protection degrees: IP X5D NOx class: 2 Power supply: LPGÿ Features list FAMILY AR Efficiency****ÿ Combined models for heating and domestic hot water production Family AR the new generation condensing boiler specifically designed to operate with high temperatures (delivery 80°C and return 60°C) and therefore in radiator systems. Family AR contains Altaresa condensing technology in the aesthetics and in the special Family functions. Family AR features Air/Gas combustion (patented): thanks to the modulating fan, the mixture of air and gas is kept optimal and constant over all the power ranges, always keeping efficiency high. Thanks to the post-exchanger in treated aluminum, very high final efficiencies are obtained, 102.9%. The climatic regulation managed directly by the boiler control unit, via the external probe (accessory), allows the temperature of the heating system to be suitably adapted to the external climatic conditions. The equipment is completed by anti-gel systems (up to -3°C), circulator anti-blocking, three-way valve vie, TastBenessere and Tastrapid which reduces waiting times for domestic hot water. Family AR available with powers of 25, 29 and 35 kW. Features:ÿ Technology, ease of management controls: ,¶½ TastMemory: activates machine intelligence. - sanitary: hot water always ready and without waste, according to the family's habits. - in heating: reduction of home heating times. ,¶½ TastBenessere: keeps the hot water supply at the ideal temperature for the shower (40øC customizable +/- 5øC). ,¶½ Touch&Go function: directly from the tap, it activates the pre-heating for a single water withdrawal. ,¶½ Intelligent system filling: allows you to fill the system in complete autonomy. Air/gas combustion (patent):ÿoptimum mixture of gas and air to obtain high and constant efficiency over the entireÿpower range with final efficiency of 102.9%.ÿ Condensing exchanger placed downstream of the fan for further recovery of the heat contained in the exhaust fumes. ÿInstallation Benefits Performance secondDir. 92/42/EEC. Circulator lowconsum(IEE0,20) Climatic adjustment managed directly by the boiler control unitÿ Special Family functions: TastBenessere, TastMemory, Touch&Go function Smart Fillsÿ Assembly template, hydraulic fittings, power supply cable supplied ErP: Energy related Products ErP the acronym for Energy related Products? (products connected to the use of energy) and the abbreviation that identifies the European Directive ErP 2009/125/EC, defined by the EEC with the intention of reducing the energy consumption of products through eco-compatible design (or eco-design?). The scope of action of this European Directive is extremely broad since up to now it has affected products such as light bulbs, air conditioners, washing machines, fans, etc. Following the publication in September 2013 of a series of implementing regulations, starting from 26 September 2015 they will also apply to heating products and the production of domestic hot water. Also from the same date, other regulations will also become effective which will implement the energy labeling of the same product families. The transitional period between the publication of the regulations and their activation throughout the territory of the European Community is necessary to allow the full transposition of the contents by companies and market players. The regulations issued require that all products intended for heating and/for the production of domestic hot water, with a nominal thermal power lower than or equal to 70 kW, are placed on the market with an ÿenergy labelÿ that highlights their efficiency class. Note: the regulation provides for the mandatory presence of the energy label for the introduction of the product from the factories to the market. All the products previously introduced, for example present near distribution warehouses, can be regularly marketed even if they do not have an energy label. Various energy labels have been provided based on the use of the generator used: for heating from A++ to G; for the production of domestic hot water from A to G. The purpose of energy labels is to allow the consumer to easily identify the level of efficiency of a product, to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pump products, as well as those on air conditioners, the efficiency data reported for the average climatic zone. In addition to product energy labels, European regulations have also provided for the creation of a "system label" in the case of building a plant in which various appliances, components and controls operate. This labelling, thanks to the combinations of the data of the various elements used in the plant, will allow the creation of systems capable of reaching levels of efficiency even higher than those of the individual generators. The European regulation states that the system label must be made available by whoever supplies and/operates the system (sellers-installers); but this faculty is also granted to builders. Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.

Read more less

Overview BIASI RECOVERY BOILER DGT 28S CONDENSING LPG LPG - NEW ErPÿ Technical specifications Model: Retrieve DGT 28S Energy label specifications according to the European ErPÿ directive Class B heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Heating/sanitary nominal heat inputkW 29.0 Maximum useful heating/sanitary powerkW 28.3 Energy efficiencynø NOx class no. 2 Minimum / maximum heating temperature**øC 40 / 85 Capacity of expansion vessel (total / useful) l 8.0 / 4.0 Maximum flow rate (T=25 K) / (T=35 K) l/minÿ16.3 / 11.6 Degrees of protection nø IPX4D Height x Width x Depth mm 803x400x350 LPG or LPG fuel supply Main features RECOVER DGTÿ ÿWall mounted condensing boilersÿ Retrieve DGTÿ theÿcondensing boilerÿdesigned for traditional systems and easily adaptable to new floor-based systems using Multizone, hot water distribution devices for heating. Recupera DGT retains the simplicity of management, programming and regulation of the traditional boiler and imports the savings of the condensing boiler resulting from the recovery of heat from the fumes. The heat recovery unit preheats the system water with the heat released by the fumes, heat which in traditional boilers is dispersed into the environment. This recovery of energy from the fumes, at typical operating temperatures of radiator systems, leads Recupera DGT to have higher yields than traditional boilers. Characteristics: High efficiency ( ( compliant with 92/42 EEC directive and Legislative Decree 311/06,¶½ Primary laminated copper heat exchanger with large exchange surface, double circulation Aluminum heat recovery unit to exploit the heat of the fumes and transfer it to the water Sanitary plate heat exchanger in stainless steel High efficiency pump with low energy consumption digital control panel with backlit display Electronic board for:ÿ Restart frequency adjustmentÿ Adjustable primary circuit thermal inertia disposalsÿ Circulator mode selectionÿ Circulator anti-seizeÿ Frost safetyÿ Chimney sweep function Integrated automatic by-pass Immunity to radio interference Magnetic sanitary flow Absolute heating pressure switch Degrees of protection IPX4D Heat recovery The heat recovery recovers the heat from the fumes before they are expelled and preheats the water directed to the primary exchanger. The recuperator made of aluminum has a finned coil which determines a large exchange surface and has a device to ensure that the boiler discharges the condensate correctly. Four-controllers Summer/winter/off selector Heating temperature regulator DHW temperature regulator Digital and analog pressure reading DHW and heating temperature visualization from the display Fault diagnostics display, fault history block status View recommended fill Display annual periodic maintenance expiry All ready for Energy Labeling What is it about From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres or As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. It's about me tooÿ YES, it affects everyone: professionals and end users The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier's responsibility The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. Responsibilities of Resellersÿ First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less