ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance IN THE ABSENCE OF THIS ITEM, THE BLUEHELIX ALPHA 24 MODEL WILL BE SHIPPED Technical features Model : Bluehelix Tech RRT 24C Energy rating Heating energy efficiency class: A DHW energy efficiency class: A ACS profile : XL Performance Heating thermal capacity: 5.0 ~ 20.4 kW Heating thermal power 80°C / 60°C : 4,9 ~ 20,0 kW Heating thermal power 50°C / 30°C : 4,9 ~ 20,0 kW DHW thermal capacity: 5 ~ 25.0 kW Sanitary thermal power: 4.9 ~ 24.5 kW Minimum efficiency 80°C / 60°C : 97.8% Maximum efficiency 80°C / 60°C : 98.0% Minimum efficiency 50°C / 30°C : 107.5% Maximum efficiency 50°C / 30°C : 106.1% G20 gas pressure : 20 bar G31 gas pressure : 37 bar NOx emission class : 6 Heating operating pressure: 0.8 ~ 3 bar Maximum heating temperature: 90°C Heating expansion vessel capacity: 8 litres DHW operating pressure: 0.3 ~ 9 bar Domestic water flow rate ∆t 25°C : 14 l/min Domestic water flow rate ∆t 30°C : 11.7 l/min Degree of protection : IP X5D Power supply (V,Hz, Ø) : 220~240/50/1 Dimensions and weight Dimensions (HxWxD): 700x420x250 mm Empty weight: 28.0 kg 5 years without worries Ferroli BLUEHELIX TECH RRT boiler Ecological wall-hung condensing boilers with Ferroli Thermobalance™ combustion cell The evolution continues.. The range of generators is equipped with the tested AISI 304 stainless steel exchanger. Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX TECH RRT is at the top of its category. BLUEHELIX TECH RRT achieves one of the highest energy efficiency of space heating in the boiler category: ηs 94% . Furthermore, when combined with the external probe and the Romeo remote timer control, it reaches system energy class A+ Extended warranty with the "5 YEARS WORRY-FREE" formula The quality of Bluehelix TECH RRT is unquestionable, and Ferroli is ready to put it to the test by offering its customers extended warranty coverage which also ensures periodic maintenance and legal checks TOP efficiency even on old systems The exchanger of the THERMOBALANCE™ thermal group by Bluehelix TECH RRT compared with the more classic and widespread steel exchanger used in the past also by the Ferroli Group exclusively on a small series of boilers produced for the English market, and then immediately abandoned in favor of the evolution towards the proprietary steel exchanger used in Bluehelix models This geometry allows the heat exchanger of the THERMOBALANCE heating unit to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments, for example due to installation on old systems, the exchanger tends to blockage much faster in the part in contact with the flame due to the reduced passage area of ​​the fluid, in which a real barrier of deposits is formed which hinder the heat exchange and reduce the efficiency below the nominal values . Product plus > Boiler with thick stainless steel primary exchanger, with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt > It reaches one of the highest seasonal space heating efficiency in its category: ηs 94% and in combination with the modulating remote control and the optional external probe it reaches the top efficiency class > Class 6 NOx : already in line with the provisions of the ErP regulation, NOx emissions < 56mg/kWh. > MC 2 : M ulti C ombustion C ontrol, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network, such as fluctuations or reduced pressures. > MGR : Methane LPG R eady, through a simple configuration the boiler is able to operate on both methane and LPG without the use of additional conversion kits > Exclusive exchanger-burner system with self-cooled door without insulators: it simplifies maintenance and reduces its cost thanks to a smaller number of perishable parts. > Instantaneous production of domestic hot water with dedicated plate domestic heat exchanger > Hydraulic connections covered by the boiler shell > Large backlit multifunction graphic display for easy and correct parameter setting > Standard by-pass > Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes > FPS : Fumes Protection System . The flue clapet valve fitted as standard on the boiler allows easy connection to pressurized collective flue systems > Designed to simplify and facilitate normal maintenance and cleaning operations > Predisposition for solar systems : prearranged for the production of domestic hot water combined with solar panel systems > ECO function in DHW for greater savings in the period of low use of hot water > 3-star certified comfort in sanitary manufacturing according to EN 13203 > Sliding temperature operation via optional external probe > Low consumption modulating heating circulator > Digital flame control with three re-ignition attempts in the event of blocking due to lack of flame detection, only for methane operation > Place of installation : also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit Innovative Ferroli THERMOBALANCE TM heating unit in its 5 elements Ferroli has oriented the design of the combustion cell and of the Bluehelix TECH RRT exchanger in order to maximize the functional advantages and the constructive sturdiness, as well as the simplicity of maintenance: the single-circuit design means that any air bubbles in the system do not remain trapped in the exchanger, and facilitates cleaning with chemical washing as much as possible, unlike spiral exchangers with double parallel circuit in which if only one of the circuits gets blocked, chemical washing is much more laborious. High flow single circuit stainless steel heat exchanger, resistant to clogging and easy to clean Self-cooled burner door without insulating panel Exclusive special stainless steel hemispherical burner with long-life gasket Intelligent “ Gas-adaptive ” system derived from industrial boilers, which monitors and self-stabilises combustion as the gas + flue conditions vary Offset fan, to facilitate maintenance of the thermal group without disassembly. Integrated smoke anti-reflux clapper for connection to CCS The engine Combustion cell The tube that makes up the BLUEHELIX TECH RRT exchanger is made of AISI 304 stainless steel , a material that allows for the creation of an extremely smooth surface , therefore less susceptible to encrusting agents and deposits. TOP quietness The new design for comfort The particularly careful design of BLUEHELIX TECH RRT has made it possible to achieve significant values ​​in terms of silence and acoustic comfort, so much so that it could almost be difficult to distinguish the background noise of a home from the noise produced by the boiler during normal operation. Even the boiler on/off transients have been optimized as a function of acoustic comfort, so that the customer will no longer have the hassle of understanding whether the boiler is on or off from its noise as with older generations of boilers. The planning also took care of the design, creating a precious mantle in 3 removable pieces, which descends to cover the pipe connections. Remote control Environment and climate BLUEHELIX TECH RRT can be combined with a wide range of remote timer controls that allow remote control and control of the appliance. The ROMEO series is made up of several models, with weekly or daily comfort programming and with the possibility of choosing between wired or wireless connection for both With the connection to the external probe, BLUEHELIX TECH RRT is able to vary the system temperature according to the external temperature measured on the basis of configurable climatic curves, guaranteeing the user greater comfort as the external climatic conditions vary. This function is internal to the electronic board of the boiler and therefore does not require the presence of the remote control , making the configuration operations easier in case of replacement. The ROMEO modulating function allows boiler output to be modulated as the set room temperature value is reached. This improves the quality of comfort by eliminating heat peaks with consequent energy savings Boiler control Control panel and functions The control and management electronics allow the user to customize the operation of the appliance in order to manage the environmental comfort according to one's needs . The key control panel and the simple LCD display make the programming operations for the production of hot water, both for domestic hot water and for heating, extremely easy and intuitive. Thanks to the remote connection via bus, this can also be done directly from the Romeo remote control. The card is protected by an easily accessible fuse thanks to the dedicated flap and the electrical connections benefit from a robust and large box, with easily accessible connectors and numerous cable ties. The boiler is also set up to connect a second room thermostat to the dedicated terminals to manage multi-zone mixing systems MC 2 Multi Combustion Control The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC 2 : Multi Combustion Control , the new combustion system with patented gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary Easy Maintenance Hassle-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the "Thermobalance" tm thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: - Internal accessibility is favored by the 3-piece shell with removable side panels. - The electrical box of the electronic card can be easily extracted from the chassis and hooked laterally, leaving free access to the internal parts - The fan, offset from the burner and placed underneath, must not be disassembled to access the steel burner-exchanger unit - The burner door is totally self-cooled by air and therefore does not require an insulating panel, avoiding the risk that this could be damaged or broken during disassembly for cleaning. - The burner can be disassembled by loosening just 3 bolts leaving free access to the stainless steel exchanger. - The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. - The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections . - Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front Simplified replacement Smoke outlet ø 50 mm The new boiler can also be installed with 50mm diameter ducting outlets. Particularly important in the replacement market in the frequent case of collective flues that require "heavy" ducting where it is necessary to have a high fume expulsion capacity even with reduced diameters. FPS .: Fumes Protection System . The flue clapet valve allows easy connection to pressurized collective flue systems . For installers, the solution of the collective pressure pipe is cheaper Comfort & Safety The designers have thought of a series of functions capable of guaranteeing the quality of the domestic water, the best delivery of power to the heating system combined with a longer life of the appliance Stop And Go function With the use of sanitary taps with mixing, short or very short dispensing for quick rinses involves the start of the boiler ignition procedure which usually ends immediately. The continuation of these " false starts " can, in the long run, compromise the average life of the product. For this reason BLUEHELIX TECH RRT provides an electronic parameter through which it is possible to delay the ignition of the burner by activating it only in the face of actual withdrawals of domestic hot water Sun Easy function BLUEHELIX TECH RRT has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. Through a sensor placed on the DHW circuit, it continuously monitors the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter falls below the level necessary to guarantee optimal comfort for the user Sanitary Eco-Comfort function In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable . Reaching maximum comfort certified 3 stars. The efficiency and load profiles according to the ErP directive are at the top of the category External installation and antifreeze function To make the most of the available space, the new BLUEHELIX TECH RRT 24C boiler can be installed recessed into the wall using the special kit. For more critical installations, in completely uncovered places not protected from the elements, the "painted cabinet" kit is also available. In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by frost . This function is active with the boiler powered by the gas circuit and under electrical voltage Product Guarantee : All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! In case of immediate lack of availability, the product will be ordered and shipped within 10 working days Technical features Model: D2CND024A0AA Heating Efficiency class (55°C) : A Fireplace power (Qn) : 2.9 - 23.5 kW Nominal heating power (80°/60 °C): 2.8 - 22.8 kW Nominal heating power (50ç/30 °C) : 3.1 - 24.0 kW Heating efficiency : Up to 108.7% Modulation range : 1:8 Expansion vessel volume: 8 litres Domestic hot water Efficiency class : A Withdrawal profile : XL Temperature range : 35°C ~ 60°C Withdrawal in continuous service (∆T=30°C): 11.3 l/min Withdrawal in continuous service (∆T=25°C): 13.6 l/min Pressure of the water network: 0.5 ~ 10 Bar Technical data Power supply (V,Hz, Ø) : 220~240/50/1 Electric Power Input: 3.5~86W Water content : 1.31 litres Sound power : 39 dB(A) Sound pressure : 49 dB(A) NOx class : 6 Exhaust gas temperature (G20) : 77° C Electrical protection class : IP X5D Installation data Flue diameter: 60/100 mm Maximum length for flue system DN 60/100 : 12.5 m Maximum length for flue system DN 80/125 : 42.8 m Maximum length for flue system DN 80/80 : 125 m Dimensions and weight Dimensions (HxLxD): 590x400x256 mm Weight : 27Kg Simply Serene Guarantee To guarantee you maximum serenity, DAIKIN has studied "SIMPLY SERENIOUS", an extension of the guarantee up to the 5th year of life of your product, which provides for the subscription of a Scheduled Maintenance Plan with specialized Daikin technicians Ultra-compact Daikin D2C condensing boilers for heating and DHW production Why choose a condensing boiler? Daikin condensing boilers are a good solution for those wishing to replace an existing boiler with a more efficient alternative, saving on costs. Our portfolio includes boilers for every need, from the D2C and Full condens and Full Condens TOP wall-hung boilers, to the GCU boiler with built-in thermal storage, to the A2 floor-standing diesel boiler Thanks to the special Daikin-patented exchanger, the D2CND boiler obtains high specific power and high partialization to guarantee comfort and efficiency in any operating mode and in minimum encumbrance. The D2T version, heating only, integrates a diverter valve and can be connected directly to a storage tank for the production of domestic hot water. Ultra-compact and elegant technology The beautifully compact boiler The new D2C condensing boilers are 100% Daikin design. The ultra-compact dimensions make them suitable for even the smallest apartments, where every centimeter saved is space gained A boiler for every need D2C boilers are available in 3 combi versions 24, 28 and 35 kW for heating and instant domestic hot water production. A wide range of heating-only boilers is also available, the D2T, in 5 sizes, from 12 to 35 kW, which can be combined with a storage tank for the production of domestic hot water. You can install them virtually anywhere thanks to their compact size and minimal installation space required. Thanks to the IPX5D degree of electrical protection and the antifreeze kit, they can also be installed outdoors. Do you want to have your heating system under control even when you are not at home? Pair the Lan Adapter to control via APP ! Efficiency and respect for the environment The combustion system with regulation via Lambda Gx probe automatically adapts to the quality of the gas used, methane or LPG, always guaranteeing clean combustion and minimum polluting emissions . Maximum comfort Thanks to a high modulation ratio, up to 1:8 , the output power is automatically varied to always adapt, instant by instant, to the real need of the house in which it is installed. Endless showers? Domestic hot water will no longer be a problem with the D2C boiler with a DHW flow rate of up to 19 l/min in the 35 kW version Cutting-edge technology combines with an attractive and user-friendly user interface Daikin Eye An elegant luminous eye which, thanks to a multi-chromatic LED, signals the operating status of the appliance. In the event of a fault, the LED turns red and the error code is displayed. The easiest way to interact with your boiler! Daikin Heating Online Controller The heating system is always under control, wherever you are! Thanks to the Daikin Heating Online Controller application you can now control and monitor your boiler from the comfort of your smartphone in a simple and intuitive way Monitor The status of your heating system The ambient temperature in your home Energy consumption graphs. Plan The temperature of your home and the operation of the boiler with up to 6 actions per day for 7 days Vacation mode Check it out The operating mode and the set room temperature The system and the production of domestic hot water By integrating third-party products and services through IFTTT services (if this then that) Changing your old boiler has never been easier! Thanks to its small size and IPX5D degree of protection, Daikin D2C can be installed practically anywhere. Its ultra-compact dimensions make it suitable for even the smallest apartments, where every centimeter saved is space gained and its elegant shapes look good in the kitchen. A distinctive element of the 100% Daikin design is also the Daikin Eye: an elegant luminous eye which, thanks to a multi-chromatic LED, signals the operating status of the appliance. Daikin D2C contains the best of condensing technology. The SCOT combustion regulation system automatically adapts to the quality of the gas used, methane or LPG, always guaranteeing clean combustion and minimum polluting emissions. Dimensions and weight reduced to a minimum are possible thanks to the innovative Daikin patented high specific capacity air/fume exchanger body. Heart of the new D2C boiler, it has been designed to obtain the highest thermal power in the smallest size. Functions Eco Mode Return temperature control to optimize condensation Warm start DHW exchanger already heated and ready for use thanks to the memorization of the habits which allows to anticipate the request for domestic hot water Solar connection If the water entering the boiler has been preheated by the solar system, the burner does not ignite, for optimal integration of the solar source Exclusive initiative for Daikin customers On the occasion of the launch of the new Daikin D2C, starting from 1 March 2017 Daikin is giving away the activation cost of Simply Serene. The offer is valid for all those who will purchase a Daikin boiler of any type and who already own a Daikin mono split or multisplit. All the details on daikin.it. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

Technical features Model : Inoa S 24 Reference : 3310664 EU Certificate Number: 0085CU0394 Type of Installation : C10-C13-C23-C33-C43-C53-C63-C83-C93-B23 Gas Category: I2H Energy Performance Nominal heat output in Heating: 4.7 ~ 20.0 kW Heating Thermal Power 60°/80° C : 4,6 ~ 19,6 kW Thermal Power : 4.9 ~ 21.0 kW Nominal heat output in DHW: 4.7 ~ 23.5 kW DHW thermal power: 4.6 ~ 23.0 kW Combustion efficiency : 98.4% Efficiency at nominal heat input 60°/80° C : 88.2 ~ 98 % Efficiency at nominal heat input 30°/50° C : 94.6 ~ 105 % Efficiency at 30% at 30° C Hi : 108.5 % Idle efficiency 60°/80° C : 87.4 ~ 97.1 % Performance Stars : ★★★★ Class : A Maximum shell heat loss ΔT = 30°C : 0.2% Losses to chimney burner in operation: 1.6% Heating Expansion vessel pre-charge pressure: 1 bar Maximum heating pressure : 3 bar Expansion vessel capacity: 8 l High temperature heating temperature : 35° ~ 82° C Low temperature heating temperature : 20° ~ 45° C Domestic hot water DHW temperature : 36° ~ 60° C Specific flow rate in DHW : 11 l/min Instantaneous quantity of hot water ΔT=25°C : 13.2 l/min Instantaneous quantity of hot water ΔT=35°C : 9.4 l/min Stars Sanitary comfort : ★★★ Minimum withdrawal of hot water: 2 l/min Sanitary water pressure: 0.2 ~ 7 bar Withdrawal profile : XL Emissions Residual head : 100 Pa NOx class : 6 Fume temperature G20 at 60/80 : 54° C CO 2 content: 9.4% Maximum flue gas flow rate: 37 Kg/h Excess air : 21% Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Total absorbed electrical power: 62 W Minimum ambient temperature of use: >0° C Electrical system protection degree: X5D Dimensions and weight Dimensions (HxWxD): 745x400x319 mm Weight : 26Kg Inoa S Compact wall mounted boiler INOA S is the new Chaffoteaux brand condensing boiler, designed to guarantee great performance and high robustness: the primary exchanger in stainless steel and the metal front panel combine efficiency and durability Installation in partially protected places MET/LPG operation with standard kit AP operation with optional kit Compatibility with positive pressure collective flues (C10) Comfort in Heating Primary condensing exchanger in stainless steel. Up to 108% efficiency and 93% seasonal efficiency. 4-star combustion efficiency in compliance with the EN92/42 standard. Modulation range from 20% to 100% of maximum power. Reduced polluting emissions, NOx class 6. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Arrangement for integration into a heating system via Ebus 2 communication protocol (boilers, solar, system management modules and modulating thermoregulation accessories). Possibility of managing single-temperature and multi-temperature zones via Expert Control. Ready for Chaffolink connectivity. Sanitary comfort Sanitary heat exchanger in stainless steel. Domestic water performance: stars *** Flow rate 13.2 litres/minute with ΔT = 25ºC (24kW) and 16 litres/min with ΔT = 25ºC (29kW). Comfort of use and installation Single-volume structure and metal front panel for greater sturdiness. LCD display and front hydrometer for better accessibility. Front electrical connections. Extremely easy access to components during maintenance (DHW exchanger, hydraulic unit, etc.) Possibility of connection with external probe. Compatible with Expert Control, modulating and on/off accessories. Easier starting: automatic purge function and directly accessible combustion regulation Energy saving and respect for the environment Up to 35% energy savings in combination with a modulating chronothermostat and external probe. 40% reduction in CO 2 emissions Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Immergas VICTRIX TERA 24 V2 low nox methane condensing boiler complete with flue gas exhaust kit General Features Model: VICTRIX TERA 24 V2 Code: 3.032927 Power supply: methane Heating Energy Efficiency Class: A Energy Efficiency Class Sanitary: A Nominal domestic hot water heat output (useful): 28.0 kW Nominal heating heat output (useful): 24.0 kW Technical data sheet (Directive 92/42/EEC method) Burner type: Blown air Power at rated load: 24.0 kW Power at 30% of nominal load: 7.2 kW (at 50/30 °C) Efficiency at nominal load: 106.5 Efficiency at 30% of nominal load: 107.5 (at 80/60 °C) Efficiency at nominal load: 97.8 Efficiency at 30% of nominal load: 96.8 Electrical auxiliaries at rated load: 41 W at medium load: 60 W at zero load: 2 W Operating temperatures Average temperature: 50 °C Return temperature: 40 °C DHW temperature: 55 °C With ACS priority: yes TEST conditions at nominal load Average generator temperature: 70 °C Performance correction factor: 0.2 intermediate load Average generator temperature: 70 °C Performance correction factor: 0.2 with no load Power loss: 54.4W Fraction of losses to the mantle: 0.36 Dimensions Legend: V - Electrical connection G - Gas supply AC - Domestic hot water outlet ACV - Domestic hot water inlet kit solar valve (optional) AF - Sanitary water inlet SC - Condensation drain (internal diameter minimum Ø 13 mm) M - System delivery R - Plant return Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS EQUIPPED WITH AUTOMATIC COMBUSTION CONTROL. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Baxi Luna Air 24 kw built-in boiler complete with Fumi-new ErP Methane or LPG exhaust kit Cod. A7736261 Technical features Sanitary nominal thermal power: 24 kW Heating nominal heat input: 20.6 kW Heating rated thermal power 80/60°C: 20 kW Heating rated thermal power 50/30°C: 21.8 kW Reduced thermal power 80/60°C: 3.4 kW Reduced thermal power 50/30°C: 3.7 kW Useful efficiency (pci) PN – average temperature 70°C: 97.7% Nominal efficiency 50/30°C: 105.8% Seasonal space heating energy efficiency class: A Seasonal energy efficiency class of the sanitary fixture: A Water heating - Load profile: XL NOx class 6 according to EN 15502 Emission of nitrogen oxides NOx 15 mg/kWh Degree of protection: IPX5D Primary water/gas coil exchanger in AISI 316L stainless steel Secondary water/water exchanger in oversized stainless steel Electric 3-way diverter valve Modulating fan with electronic speed variation Automatic by-pass on the heating circuit Dimensions (boiler) hxwxd: 770 x 470 x 238 mm Dimensions (case) hxwxd: 1170 x 600 x 240 mm MOON AIR Luna Air is the new range of condensing boilers ideal for outdoor installations. remote digital control panel with LCD display as standard suspended installation in partially protected places open-air suspended installation with cover kit, available as an accessory minimum operating temperature: -15°C antifreeze function and IPX5D protection degree wide modulation range 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control built-in installation: the ultra-compact dimensions of the boiler, 770x470x238 mm, allow it to be installed in the majority of boxes on the market; recessed telescopic fittings kit available as an accessory predisposition for combination with the Baxi integrated solar system connection to Ø50 mm rigid and flexible drain pipe - for mod. 24 kW total length (exhaust+intake) 40 metres: solution for renovating flues and in case of replacement of a natural draft boiler with a condensing boiler With Luna Air it is possible to create three different installations: suspended installation in partially protected places; open-air wall-hung installation with cover kit; recessed installation with containment box Product Guarantee : All products for sale on our site are new and packed. The warranty on this product is 24 months from the date of purchase

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Technical features ErP energy efficiency class (heating and DHW): A Load profile: XL DHW nominal heat input kW 24.7 Heating nominal heat input kW 20.6 Sanitary nominal thermal power kW 24 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.7% Efficiency at 100% Pn (50-30°C): 105.8% Expansion/pre-charge vessel capacity l/bar 7.5/0.8 Sanitary water temperature adjustment °C 35-60 Boiler capacity 40 l Boiler expansion vessel capacity/pre-charge l/bar 2/2.5 Sanitary water production ∆T 25°C l/min 13.8 Sanitary water production at discharge ∆T 30°C (1) l/30' 385 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions (hxlxp): 950x600x466 mm ; 62 kgs Power supply: CNG or LPG Cloud Duo-Tec+ Digital control panel The Duo-tec E range of boilers is equipped with a new digital control panel with an even more backlit LCD display, clearer and simpler to use thanks to dedicated and independent keys for regulating the temperature of the domestic hot water and of the heating. The display allows you to view all the information and set the operating parameters in an intuitive and immediate way. Efficiency and savings Wide modulation range: greater efficiency given by fewer starts and stops: with a high modulation ratio, the reduction of the continuous on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions adaptation of the thermal power produced to the power dissipated thus avoiding excessive overheating / cooling of the premises GAC Gas Adaptive Control It is an innovative system which, thanks to a new control electronics and a new electronic gas valve, guarantees automatic control of combustion to constantly maintain maximum efficiency values. Advantages: there are no manual interventions – reduced measurements, calibrations with this system, the boiler self-adapts to the quality of the gas (methane) and to the length of the flue gas pipes, keeping the efficiency constant the boiler also constantly regulates itself to maintain the maximum efficiency values, favoring a reduction in gas consumption and generating less pollution thanks to the continuous control of emissions. Fully modulating pump with de-aeration The circulation pump can operate at maximum speed, minimum speed or in "automatic" mode: in the latter case, the speed (min./max) will be selected so that the delivery/return ∆T in heating remains constant at 20 °C thus ensuring a significant reduction in pump consumption and, given the lower mechanical stresses (compared to a pump that always runs at maximum speed), also in maintenance costs. During the first ignition phase, we recommend activating the automatic de-aeration function. This function eliminates the presence of air in the heating circuit and therefore avoids any blockages of the boiler, overheating of the system, etc. Guidelines in case of replacement of a conventional boiler with a new condensing one There are two main problems that can be encountered: Flues and smoke exhaust duct Condensate drain To overcome the above, Baxi recommends: the use of a Ø50 mm exhaust pipe Baxi has in fact developed a system that allows easy ducting in existing flues (for 24kW models). For condensing boilers, the novelty is brought about by the low temperatures of the fumes which allow the use of specific plastic materials; however, in the presence of existing 316 stainless steel flues, installed correctly and with gaskets suitable for receiving damp fumes, there are no problems and they can easily be reconnected to the new boilers while it is absolutely not compliant with the use of aluminum flues or smoke pipes . In fact, aluminum is a metal that is not resistant to the acid condensates present in the fumes. (*) Each Ø50 mm diameter bend decreases the length of the drain by 4m the use of the condensate drain pump Baxi has designed this kit to collect the condensate produced by condensing boilers for domestic use: the pump allows the creation of condensate drainage systems in the absence of natural drainage near the boiler. The operation of condensing boilers determines the formation of condensate, due to the principle of condensation. This water therefore needs to be disposed of through special drains. If there is no adequate slope and therefore it is not possible to dispose of the condensate by gravity, it is necessary to install a pump that conveys it towards the drains. The pumps used are also equipped with special non-return valves to avoid bacterial contamination due to any stagnation and return of the waste water. The use of buildings avoiding the use of annoying pipes. Characteristics : Wide modulation range 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control Up to 500 l of hot water in 30 minutes (ΔT 30°C) 40 l stainless steel kettle Digital control panel with large backlit LCD display Compatibility with the Baxi Mago (optional accessory) for remote boiler control DHW expansion vessel available as STANDARD (for 33 kW mod.) and as an accessory (for 24 kW mod.) Connection to rigid and flexible Ø50 mm exhaust pipe: solution for restoring flues - mod. 24 kW total length 40 meters (intake+exhaust) STANDARD installation kit (gas cock / DHW inlet / telescopic fittings) hydraulic system Electric three-way diverter valve Pre-mix burner in stainless steel Flue water exchanger in stainless steel Stainless steel kettle Modulating fan with electronic speed variation Automatic by-pass High efficiency circulation pump with total modulation Pump anti-blocking system and three-way valve which intervenes every 24 hours Heating circuit safety valve at 3 bar 8 bar boiler safety valve Sanitary expansion vessel (2 litres) standard for mod. 33 GA VES Sanitary recirculation arrangement Thermoregulation system Standard climate control (with external probe available as an option) Arrangement for connection to a zone system Control system Safety thermostat against overheating of the water/fumes exchanger Hydraulic pressure switch which blocks the gas in case of water shortage Safety thermostat against fume overheating Temperature control using NTC probes Anti-legionella function Total antifreeze device Electronic thermometer Heating circuit digital pressure gauge Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENZIONE  LA CALDAIA VIENE FORNITA A METANO. PER LA TRASFORMAZIONE A GPL, RIVOLGERSI PREVENTIVAMENTE AL SERVIZIO ASSISTENZA AUTORIZZATO Caldaia Junkers Bosch Condens 4300 W GC4300W 24/25 C 23 a condensazione con di kit scarico fumi Caratteristiche Tecniche Dati del prodotto per il consumo energetico (ErP), secondo requisiti dei regolamenti UE n. 811/2013 e 812/2013 e s.m.i. a completamento della direttiva 2017/1369/UE C4300i W 24/25 Classe di efficienza energetica di riscaldamento (A+++ → D) A Classe di efficienza energetica di riscaldamento dell’acqua (A+ → F) A - Potenza termica nominale kW 24 Profilo di carico dichiarato XL - Efficienza energetica stagionale del riscaldamento d’ambiente ηs* % 94 Dati tecnici Portata termica nominale (Qn) di riscaldamento kW 3,2-24,6 Potenza termica nominale (Pn) 80/60 °C kW 3-24 Potenza termica nominale (Pcond) 50/30 °C kW 3,3-24,7 Portata termica nominale massima acqua calda sanitaria (Qn,maxWW) kW 25,5 Portata specifica secondo EN 13203-1/2 (ΔT = 30 K) l/min 11,9 Rendimento utile alla potenza massima ηu,Hi,100% 50/30 °C % 103,1 Rendimento utile alla potenza massima ηu,Hi,100% 80/60 °C % 97,6 Rendimento utile alla potenza minima ηu,Hi,30% 50/30 °C % 107,5 Rendimento utile alla potenza minima ηu,Hi,30% 80/60 °C % 98 Capacità vaso espansione riscaldamento l 6 Classe NOx (secondo EN 15502/1) 6 Grado di protezione elettrica IP X5D Potenza sonora dB(A) 45 Peso kg 35,25 Dimensioni (LxAxP) mm 400x710x300 Condens 4300 W Un’installazione così semplice non l’hai mai provata prima Grazie ai nuovi attacchi idraulici, Condens 4300i W è la caldaia a condensazione ideale per la sostituzione e l’ammodernamento di qualsiasi modello di caldaia a gas. Così, ai tuoi clienti proponi qualità ed efficienza, e tu ti assicuri un lavoro semplice e veloce. Perfetta per gli interventi di sostituzione Con nuovi attacchi idraulici che distano ben 11 cm dal muro, Condens 4300i W è la scelta ideale in casodi ristrutturazione e per completare i lavori di sostituzione in tutta semplicità e in poco tempo. Inoltre, questa caldaia non necessita dello spostamento dello scarico fumi, perché è possibile mantenere il foro pre-esistente. L’ampia gamma di modelli di scarico fumi Bosch, disponibile in diverse lunghezze, consente di scegliere anche il nuovo scarico fumi con sdoppiatore compatto (disponibile come accessorio).Trova spazio in ogni contestoCondens 4300i W è pensata per trovare spazio ovunque e adattarsi a diversi contesti abitativi, risultando ancora una volta la scelta ideale per i lavori di ammodernamento. Le sue dimensioni estremamente compatte (con soli 30 cm di profondità, 40 cm di larghezza e 71 cm di altezza) fanno sì che possa trovare spazio in ogni ambiente domestico, anche all’interno dei pensili. Il peso estremamente contenuto, con soli 35 chili, ne conferma ancora una volta la grande praticità di installazione.Altamente efficiente, estremamente silenziosaSemplicità di installazione, dimensioni compattem e peso contenuto: cosa chiedere di più? Condens 4300i W è la soluzione perfetta anche per la sua grande silenziosità di funzionamento, per cui la sua presenza passa praticamente inosservata! Con una potenza sonora di 45 dB(A), Condens 4300i W c’è, funziona alla perfezione, ma non si sente!  Modernità e robustezza, la scelta ideale per le ristrutturazioniCondens 4300i W è funzionale e moderna sotto ogni aspetto, sia a prima vista che al suo interno. Componenti di alta qualità, design elegante e affidabilità nel tempo, uniti alla semplicità di installazione, la rendono la scelta ideale per i progetti di ammodernamento in ogni tipo di abitazione I principali vantaggi Nuovi attacchi idraulici distanti 11 cm dal muro Possibilità di mantenere il foro esistente dello scarico fumi Dimensioni ultra compatte e peso contenuto Elevata efficienza garantita dall’ampio range di modulazione fino a 1:10 Comfort sanitario a 3 stelle, il massimo ottenibile secondo la normativa EN13203-1/2 Elevata silenziosità di funzionamento con soli 45 dB(A) di potenza sonora Controllabile tramite display LCD o da remoto tramite app Consente di accedere agli incentivi fiscali previsti per l’efficientamento dell’impianto di riscaldamento Il riscaldamento domestico a portata di manoCondens 4300i W è facile da controllare tramite l’intuitivo display LCD, ma non solo: grazie alla compatibilità con un’ampia gamma di regolazioni, gestire questa caldaia è semplicissimo! Un’ampia gamma di regolazioni per incrementare l’efficienza energeticaCondens 4300i W dispone di un display LCD che consente all’utente di regolare con facilità tutte le impostazioni di base della caldaia. Inoltre è compatibile con un’ampia gamma di termoregolazioni.Questo consente di: mantenere la regolazione pre-esistente sostituire la vecchia regolazione con un modello Bosch abbinato ad una sonda esterna, in modo da incrementare l’efficienza energetica del sistema di riscaldamento e ridurre i consumi. La scelta della regolazione impatta sugli incentivi fiscali a cui è possibile accedere. Consumi ridotti e prestazioni al top: installa solo il meglio! Condens 4300i W, grazie all’ampio range di modulazione e all’elevato rendimento stagionale, è sinonimo di efficienza energetica e consumi ridotti. Così, non solo il tuo lavoro è subito fatto, ma sei certo di aver offerto ai tuoi clienti solo il meglio della tecnologia Bosch! Comfort domestico sempre al topIl bruciatore modulante di Condens 4300i W, con range fino a 1:10, si adatta in automatico al reale bisogno di calore del momento, raggiungendo un’elevata efficienza stagionale per il riscaldamento d’ambiente con valori fino al 94%. Questo, per il cliente, si traduce non solo in un elevato comfort domestico, ma anche in consumi ridotti e costi di riscaldamento più contenuti.Acqua calda sanitaria subito disponibileL’elevata efficienza di Condens 4300i W è anche garanzia di tanta acqua calda sanitaria a temperatura costante con tempi di attesa davvero ridotti. Così, con un comfort sanitario a 3 stelle, il massimo ottenibile secondo la normativa EN13203-1/2, la soddisfazione desl cliente è garantita! Garanzia Prodotto : Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.

Read more less

Caratteristiche tecniche Modello : Residence IN 25 KIS Codice prodotto : 20189650 Potenza nominale : 19,0 kW Alimentazione : Metano/gpl Efficienza energetica Classe di efficienza energetica stagionale del riscaldamento : A Classe di efficienza energetica del sanitario : A Efficienza energetica stagionale del riscaldamento : 93% Consumo energetico annuo : 42 GJ Potenza termica utile Potenza termica nominale e a regime di alta temperatura : 19,4 kW Potenza termica nominale e a regime di bassa temperatura : 6,5 kW Efficienza utile Alla potenza termica nominale e a regime di alta temperatura : 87,3 % Al 30% potenza termica nominale e a regime di bassa temperatura : 98,5 % Consumi elettrici ausiliari A pieno carico : 32,0 W A carico parziale : 12,0 W In modalità Stand-by : 3,0 W Performance in riscaldamento Portata termica : 3,95 ~ 25 kW Pressione massima : 3 bar Temperatura massima : 90° C Performance in sanitario Portata ACS minima : 2 l/min Pressione massima : 8 bar Produzione ACS : 10,2 ~ 11,9 ~ 14,3 kW Dati installativi Diametro tubo entrata / uscita riscaldamento : 3/4" Diametro tubo entrata / uscita sanitario : 1/2" Dimensioni e peso Dimensioni (AxLxP) : 740x420x249 mm Peso : 31,0 Kg Caldaia murale a condensazione Riello RESIDENCE IN La soluzione efficiente, dove lo spazio fa la differenza Residence In è la soluzione Riello pensata per le esigenze installative in cui lo spazio fa la differenza e per un comfort senza compromessi. Residence In si distingue per compattezza, flessibilità applicativa e ampia disponibilità di accessori che garantiscono la compatibilità e retrocompatibilità anche nei box Riello più piccoli.  Lo scambiatore primario, interamente realizzato in acciaio inox e con accessibilità frontale alla camera di combustione, e lo scambiatore a piastre ottimizzato assicurano la massima efficienza e affidabilità nel tempo e garantiscono un comfort elevato, sia in riscaldamento che in sanitario Con RESIDENCE IN, Riello continua il percorso di rinnovamento della propria offerta murale in chiave eco-compatibile. L’ampio range di modulazione 1 : 8, le bassissime emissioni di NOx, che posizionano la gamma in Classe 6 (la migliore secondo gli standard europei), e la predisposizione per il funzionamento con miscele di gas naturale e idrogeno – fino a un massimo del 20% - sono solo alcune tra le caratteristiche che qualificano RESIDENCE IN come la caldaia ideale per un’installazione di valore nel tempo, dal minimo impatto ambientale ed estetico. Installazione universale Massima flessibilità installativa sia all’interno, all’esterno (in luogo parzialmente protetto) e a incasso in box Stabilità di acqua calda sanitaria Acqua calda senza oscillazioni di temperatura, per un comfort ottimale durante i prelievi Interfaccia digitale  Interfaccia dal design moderno, che si distingue per l’intuitività di utilizzo, comunicando con l’utente per mezzo di icone e testi scorrevoli. Basse emissioni La migliore in termini di rispetto ambientale a livello europeo Compattezza e flessibilità per un'installabilità universale RESIDENCE IN è la soluzione ideale per la sostituzione, oltre che per la nuova edilizia. Le dimensioni ridotte del prodotto, unitamente alla disponibilità di una gamma articolata di kit accessori per ogni tipo di applicazione, facilitano e velocizzano l’installazione, anche in piccoli box pre-esistenti. RESIDENCE IN, come suggerisce il nome, è la nuova caldaia Riello pensata in primis per l’installazione a incasso in box. Grazie alle ridotte dimensioni e alla disponibilità di una gamma dedicata di kit accessori, RESIDENCE IN è compatibile e retrocompatibile con le varie tipologie di box Riello. La nuova soluzione Riello, in caso di sostituzione di un modello a incasso, assicura all’utente un notevole risparmio, evitandogli sia l’acquisto di un nuovo box, che eventuali spese murarie per adeguare lo spazio della nicchia. Inoltre, gli attacchi idraulici con sequenza Riello rendono la sostituzione con le vecchie caldaie ancor più facile e immediata. L’installabilità a incasso è un plus anche per la nuova edilizia, permettendo di risparmiare spazio sempre più prezioso all’interno dell’abitazione e riducendo al minimo l’impatto estetico in facciata. Adatta per l'esterno RESIDENCE IN, grazie al grado di protezione IPX5D e al kit accessorio antigelo fino a -15°C, può essere installata anche all’esterno dell’abitazione, in luogo parzialmente protetto. Design moderno e utilizzo intuitivo RESIDENCE IN è dotata di un pannello di controllo dalle linee razionali e moderne, che si distingue per la semplicità di utilizzo. Attraverso il display LCD retroilluminato, che comunica con l’utente mediante icone e testi scorrevoli, è possibile accedere facilmente a tutte le funzioni di RESIDENCE IN. Un cuore d'acciaio per la massima efficienza RESIDENCE IN è dotata di un nuovo scambiatore primario in acciaio INOX, con tubo liscio ad elevata sezione, in grado di assicurare la migliore efficienza e pulizia nel tempo. L’acciaio INOX, oltre all’elevata resistenza all’azione corrosiva della condensa acida, previene la formazione interna di ossidi e di altri fenomeni elettrochimici tipici delle installazioni in vecchi impianti. La geometria a spira unica avvolta (circuito idraulico in serie) assicura una portata costante in tutte le sezioni dello scambiatore e previene intrinsecamente fenomeni di intasamento. L’accesso frontale agevola le operazioni periodiche di manutenzione e pulizia della camera di combustione. Comfort sanitario elevato Grazie al nuovo scambiatore a piastre high performance, RESIDENCE IN offre un elevato comfort in sanitario, con disponibilità di acqua calda in tempi brevi e un’ottima stabilità della temperatura di erogazione. Funzionamento silenzioso RESIDENCE IN, distinguendosi per la silenziosità operativa, rappresenta la scelta ottimale anche per l’installazione in locali non tecnici, ad esempio in caso di sostituzione in una cucina. Garanzia prodotto : Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.

Read more less

ATTENTION THE BOILER IS BORN WITH METHANE. SO THE TRANSFORMATION KIT IS REQUIRED. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE VAILLANT ecoTEC PRO CONDENSING VMW 286/5-3+ COMPLETE WITH FUME EXHAUST KIT -ErP Technical features For heating and domestic hot water production Forced draft sealed chamber Nominal thermal power 24.0 kW ErP energy class (Heating and DHW): Class A DHW nominal heat input 28.6 kW Nominal heat input in heating mode 24.5 kW Water content in the generator 2.2 l Expansion vessel capacity 10 l Domestic hot water production (ΔT = 30K) 13.4 lt Dimensions (hxpxl) mm 720 x 338 x 440 ; 36kg Version: LPG (WITH SPECIAL TRANSFORMATION KIT) General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. EcoTEC PRO The wall mounted boiler that offers the right balance between performance and comfort. The ecoTEC pro VMW (heating and DHW production) are available in power ratings of 19 and 24 kW. ecoTEC pro was born as the natural evolution of Vaillant's consolidated technology and experience in condensing technology. ecoTEC pro has been designed to offer the right balance between performance and comfort both in heating and in the production of domestic hot water. Its simplicity of regulation makes it the ideal boiler for all users. ecoTEC pro is equipped with an extremely simple interface with plain text and backlit display. The small dimensions of ecoTEC pro VMW 70cm high, 44cm wide and 35cm deep (identical to the previous version) allow installation in any environment. A new high-efficiency pump and new electronics allow ecoTEC pro to consume very little electricity, guaranteeing considerable savings throughout the year. Instant DHW production Intuitive user interface Simplicity of management ****Efficiency in heating Modulation 1:5 Modulating pump (Class A) Steel primary exchanger 10 l expansion vessel transfer kit from methane to propane or propane air code 0020160884 Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Immergas VICTRIX TERA 24 V2 low nox LPG condensing boiler complete with flue gas exhaust kit General characteristics Model: VICTRIX TERA 24 V2 Power supply: LPG Heating Energy Efficiency Class: A Sanitary Energy Efficiency Class: A Sanitary nominal thermal power (useful): 28.0 kW Heating nominal heat output (useful): 24.0 kW Technical data sheet (Method Directive 92/42/EEC) Burner type: Blown air Power at rated load: 24.0 kW Power at 30% of nominal load: 7.2 kW (at 50/30 °C) Efficiency at nominal load: 106.5 Efficiency at 30% of nominal load: 107.5 (at 80/60 °C) Efficiency at nominal load: 97.8 Efficiency at 30% of nominal load: 96.8 Electric auxiliaries at rated load: 41 W at intermediate load: 60 W at zero load: 2 W Operating temperatures Average temperature: 50°C Return temperature: 40°C DHW temperature: 55°C With DHW priority: yes TEST conditions at nominal load Average temperature of the generator: 70 °C Yield correction factor: 0.2 at intermediate load Average temperature of the generator: 70 °C Yield correction factor: 0.2 at zero load Power lost: 54.4W Mantle loss fraction: 0.36 Dimensions Legend: V - Electrical connection G - Gas supply AC - Domestic hot water outlet ACV - Kit domestic hot water inlet solar valve (optional) AF - Domestic hot water inlet SC - Condensate drain (internal diameter minimum Ø 13 mm) M - System delivery R - System return Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

GAS BOILER UNICAL KON M C24 CONDENSING LOW NOX COMPLETE WITH LPG FUME KIT Model: KONm 24C Energy efficiency: Seasonal efficiency class for heating A Declared load profile: XL Sanitary seasonal efficiency class: A Technical data: Nominal useful power kW 23.6 Seasonal heating energy efficiency ambient ηs 92% Useful thermal power in high temperature regime. (Tr 60 °C / tm 80 °C): 12.7kW Efficiency at nominal thermal power in high temperature regime (Tr 60 °C / Tm 80 °C) η4: 87% Useful power at 30% of nominal thermal power in low temperature regime (Tr 30 °C): 4.2kW Efficiency at 30% of nominal thermal power in low temperature regime (Tr 30 °C) η1: 96.7% Annual electricity consumption QHE GJ: 40 Heating energy efficiency. of water ηWH: 86% Daily fuel consumption Qfuel : 22.0 kWh Sound power level indoors Lwa dB(A) 51 Annual electricity consumption AEC: 400kWh Domestic hot water specific flow rate (Dt 30 °C): 11.2 l/min DHW production in cont. Dt 25 K (mixed): 13.2 l/min Expansion tank capacity: 8 lt Heating circuit pressure (min-max): 0.5-3.0 bar DHW circuit pressure (min-max): 0.5-6.0 bar IP X5D degree of protection NOx class: 6 Dimensions (HxWxD): 700x420x345 mm; 36.5kg KONm the latest generation of domestic condensing boilers by Unical, available in the version: instant combo heating only combinable with DSP 110 stainless steel boiler. KONm presents all the "Quality Stars" to satisfy every need: Exceptional modulation ratio up to 1:8 Efficiency >107% (ex dir. CE 92/42) Primary exchanger in ultra-flat Al/Si/Mg Electronics with HWS “Hot Water Speed” function (vers. C) Low NOx (class 5 according to EN 297 and EN 483) thanks to the modulating premix burner Production of hot water up to 13.3 l/min Δt 25 with special 12-plate (mod. 24 C) and 16-plate (mod. 28/35 C) stainless steel exchanger “Pit stop” maintenance Simple and intuitive control panel Prepared for future applications in systems and suitable for meeting the requirements of the new installation standards High efficiency modulating circulator Managing 2 zones with 2 KON m thermostats is versatile. Ideal for all systems, thanks to the electronics that allow you to manage 2 heating zones at different temperatures (high for radiators and fan-coils, low for radiant panel systems) by controlling them with dedicated modulating and on-off thermostats Anti-overheating post-circulation of 15 seconds, it maintains the thermal equilibrium between delivery and return, even after intense DHW withdrawals, while in heating, with a duration of 5 minutes, it allows all residual thermal inertia to be disposed of. Sliding temperature operation for maximum running economy Antifreeze protection intervenes at 5°C and is activated in both DHW and heating, bringing the temperature in the boiler to 15°C. The risk of KON m freezing if low temperatures persist in the room where it is installed is avoided. If there is a lack of gas, the lockout signal will appear on the display. Pump anti-blocking prevents blocking of the pump following long stops thanks to an automatic 5-second impulse that the electronics sends to the motor every 24 hours of stop. Chimney sweep function adjustment of combustion easier than ever. Pressing the release button for more than 5 seconds to obtain operation at minimum or maximum power for 15 minutes, for an accurate analysis of the combustion The details of konm... Strengthened by the company's constructive synergies, KONm summarizes some aspects of the high-end series such as the primary heat exchanger in Al/Si/Mg with low water content by "Scuola Unical", the original rapid inspection mechanism of the vital parts of the combustion together with the extensively tested but updated complex of electronics and electro-pneumatic control pre-mixing system already in use on other ranges. A sober answer with high technological content "ErP Ready", ideal for the consumer who approaches technologies with high energy recovery and for the installer who requires simple but not trivial solutions in plant replacement or in new buildings with low environmental impact . KONm is signed by Unical. Exclusive exchanger in Al/Si/Mg It is made of a special Aluminium/Silicon/Magnesium alloy which ensures efficiency and resistance, so much so that it is guaranteed by Unical for 5 years. Thanks to the internal heat exchange configuration, efficiencies of over 107% are achieved in condensing mode, which means great economic savings and very low environmental impact for the user. The 28-35 versions are adequately oversized Modulating circulator with deaerator It represents the state of the art in the high efficiency standard. In line with the 2015 ErP directive, with less than 1 W consumption in stand-by and only 45 W in maximum operation, thanks to the wide modulation capacity, based on the request of the room thermostat and the temperatures detected by the sensors placed in delivery/return, it automatically doses the power of the boiler to the needs of the system. Particularly silent and compact, it integrates with the safety valve, the by-pass and the drain cock. Fan and electro-pneumatic gas valve The pre-mixing unit made up of a pneumatic gas solenoid valve and modulating fan stands out for its limited overall dimensions. Advantages: compactness and silence wide 1:8 modulation range absolute operating safety due to the absence of turbulence low thermal and mechanical stresses, therefore long life, thanks to the inalterability. The valve is designed to compensate for gas pressure fl uctuations present in networks as well as to stabilize the supply pressure independently of the suction pressure generated by the premix fan. The 28/35 version is equipped with a silenced air intake to improve acoustic performance and also with a larger air intake manifold. Easily adjustable, it ensures an accurate air/gas combustion mixture to ensure high CO2 levels and favor condensation with very low CO and NOx levels. In summary, the monoblock lends itself to easy maintenance and accessibility. Exchanger cleaning 1 minute and 46 seconds! KONm is the result of the experience of the Service and market suggestions, from which the Unical design staff has synthesized a technological complex that can be easily assembled and quickly disassembled. Intuitive controls The on-board electronic panel will feel immediately familiar. Last but not least: all wiring and intervention operations are facilitated by the vertical tilting system. The multifunction LCD display, with timed backlighting, allows: Reading of the temperatures in heating and DHW Display of blockage due to lack of fl ame Operating/stand-by status Diagnostics with signaling of 11 anomalies Knob: stand-by, mode selector and heating adjustment 30 - 85°C DHW adjustment knob 38 - 60°C Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.  

Read more less

Caldaia a Condensazione Beretta BLR 25C low NOx Metano con kit scarico fumi 20213289 SPECIFICHE ETICHETTA ENERGETICA,(in accordo alla Direttiva ErP) Codice caldaia (alimentazione MTN) 20213289  Classe di efÏcienza energetica stagionaledel riscaldamento A  Classe di efÏcienza energetica del sanitario A  Potenza nominale secondo ErP pnominal kW 19  EfÏcienza energetica stagionale del riscaldamento ŋs % 93  POTENZA TERMICA UTILE Alla potenza termica nominale e a regimedi alta temperatura (*) P4 kW 19,4 Al 30% potenza termica nominale e a regimedi bassa temperatura (**) P1 kW 6,5 ALTRI PARAMETRI Perdite termiche in modalità Stand-by Pstby W 30 Consumo energetico annuo QHE GJ 42  Livello potenza sonora, all’interno LWA dB 53  Emissioni NOx NOx mg/kWh 22  PER GLI APPARECCHI DI RISCALDAMENTO COMBINATI Profilo di carico dichiarato Xl EfÏcienza energetica dell’ACS ŋwh % 84  Consumo giornaliero energia elettrica Qelec kWh 0,133  Consumo giornaliero di combustibile Qfuel kWh 23,183  Consumo annuo energia elettrica AEC kWh 29  Consumo annuo di combustibile AFC GJ 18  ALTRE SPECIFICHE TECNICHE Portata termica riscaldamento (max-min) kW 20,0 - 3,1  Portata termica ACS nominale (max-min) kW 25,0 - 3,1  Tensione di alimentazione V-Hz 230 - 50 Grado di protezione IP IPX5D Classe NOx 6  RISCALDAMENTO Pressione-temperatura max bar-°C 3-90  Pompa: prevalenza massima disponibile(alla portata di 1000 l/h) mbar 408 Vaso d’espansione a membrana l 8  SANITARIO Pressione max bar 8  Produzione ACS a ∆T= 25 °C / 30 °C / 35 °C l/min 14,3/11,9/10,2 Portata ACS minima l/min 2  COLLEGAMENTI GAS E IDRAULICI Pressione nominale gas (G20-G31) mbar 20-37 Mandata-Ritorno riscaldamento/Entrata gas Ø 3/4" Entrata/Uscita sanitario - Mandata/Ritorno bollitore Ø 1/2" DIMENSIONI, PESO Dimensioni caldaia (AxLxP) mm 700x400x275 Peso netto kg 28,5  BLR BLR È LA PROPOSTA DI CALDAIE MURALI A CONDENSAZIONE BERETTA VOLTE ALRISPARMIO ENERGETICO E ALL’EFFICIENZA.Questa gamma, che conserva le caratteristichedistintive delle caldaie firmate Beretta in termini di affidabilità, semplicità di utilizzo e rispetto dell’ambiente, offre una varietà di caratteristiche e vantaggi innovativi, tra cui lo scambiatore primario in acciaio inox, un’interfaccia touchpad intuitivae di facile utilizzo e le connessioni idrauliche con standard DIN. Inoltre, l’elevato rapporto di modulazione (1:8), la flessibilità installativa, le dimensioni compatte e il peso contenuto, fanno di BLR un prodotto adatto alle più svariate esigenze di comfort.la caldaia BLR è orientata al futuro, infattiè predisposta a funzionare con miscele di idrogeno fino al 20%, contribuendo così a ridurre l'impatto ambientale e le emissioni delle caldaie a condensazione nei prossimi anni. Il comfort a portata di touch BLR è facile da utilizzare e da programmare, grazie alla presenza di un’interfaccia digitale touchpad. Sia l’utente finale che l’installatore possono accederefacilmente a tutte le funzioni della caldaia attraverso un display LCD con icone intuitive che consentono una comprensione immediata della funzione visualizzataAdatta ad ogni ambienteGrazie alle sue dimensioni compatte e al peso contenuto, BLR può essere facilmente installata in ogni ambiente della casa, sia all’interno, ma anche all’esterno (a incasso in box o in luogo parzialmente protetto). Questo prodotto è ideale per la sostituzione di vecchiecaldaie e presenta connessioni con sequenza di tipo DIN che, grazie alla disponibilità di kit accessori forniti da Beretta, ne semplificano la conversione.L’offerta BLR è completata da un’ampia gamma di accessori: kit fumi, filtri acqua compatti (addolcitore e magnetico) e copertura delle connessioni idrauliche.Scambiatore a condensazione in acciaio inoxLa gamma BLR di Beretta è dotata di uno scambiatore primario in acciaio INOX, con tubo liscio ad elevata sezione, che assicura efficienza e pulizia nel tempo, attraverso un’elevata resistenza all’azione corrosiva della condensa acida, prevenendo la formazione interna di ossidi e di altri fenomeni elettrochimici tipici delle installazioni in impianti datati. La geometria a spira unica avvolta (circuito idraulico in serie) assicura portata costante in tutte le sezioni dello scambiatore e previene intrinsecamente fenomeni di intasamento. L’accesso frontale agevola le operazioniperiodiche di manutenzione e pulizia della camera di combustione. AMPIO RANGE DI MODULAZIONE PREMIX: 8:1 BASSO NOX: CLASSE 6 (EN 15502) TERMOREGOLAZIONE INCORPORATA CON SONDAESTERNA DISPONIBILE COME ACCESSORIO CERTIFICAZIONE RANGE RATED PER ADATTARE LA POTENZA DELLA CALDAIA ALLE REALI RICHIESTETERMICHE DELL'IMPIANTO  PROTEZIONE ELETTRICA IPX5D  FLANGIA FUMI CON COLLARE DI SICUREZZAA RAPIDO SERRAGGIO E PRESE ANALISI FUMIINTEGRATE CIRCOLATORE A BASSO CONSUMO (EEI ≤ 0,20), CON CURVA DI PREVALENZA 6 M COPERTURA CONNESSIONI IDRAULICHE E AMPIA GAMMA DI ACCESSORI DISPONIBILI COME OPTIONAL COMPATIBLE CON LA PIATTAFORMA HI, COMFORT DI TERMOSTATI SMART, SIA IN MODALITA' ON/OFF CHE WI-FI CON COMUNICAZIONE OTBUS Garanzia prodotto : La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.

Read more less