FERROLI BLUEHELIX K 50 25 Kw CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Characteristics: Seasonal space heating energy efficiency class A Water heating energy efficiency class A Declared load profile XL Heat Capacity (PCI) Min / Max Heating: 5.8 / 25.0 Thermal power 80°C-60°C: 5.7 / 24.5 Useful thermal efficiency 80°C-60°C Pmax % / Pmin %: 98.0 / 97.8 Emission class Nox class 5 Boiler capacity 50 litres Domestic hot water production Δt 30°C l/10 min 175 Sanitary Manufacturing (EN 13203) ★★★ Heating working pressure Max bar 3 DHW working pressure Max bar 9 Empty weight kg 50 Dimensions HxWxD: 800 x 600 x 420 Power supply: METHANE Certified operation also with LPG using a special kit to be requested from the Authorized Assistance Centre CHARACTERISTICS Boiler body with the new patented primary exchanger in thick AISI 316 TI stainless steel Production of domestic hot water with 50-litre stainless steel domestic hot water storage tank Total premix burner in stainless steel Electronic flame modulation both in heating and DHW Digital control panel Can be combined with the modulating remote timer control Low consumption modulating heating pump (Erp Ready - Class A) Refined design and compact size Casing painted in white by anaphoresis with epoxy powders 3-star certified comfort in sanitary manufacturing according to EN 13203 Sliding temperature operation via optional external probe Digital flame control with three re-ignition attempts in case of operation due to lack of flame detection (methane model) Arrangement for recirculation attachments Standard by-pass Place of installation: also for outdoors in a partially protected place up to - 5 ° C as standard TANGIBLE FACTS max consumption standard non-modulating circulator: 0.085 kW max consumption new high efficiency circulator: 0.04 kW Degree days 2500 (average climate zone E) Energy cost: €0.19/kWh * Hypothetical annual expenditure at max standard circulator speed: €40.375 Hypothetical annual expenditure at max speed of high efficiency circulator: €11.4 Therefore, with the replacement of standard boilers with Bluehelix K 50, in line with the new ERP regulations, electricity savings of around 30% can be estimated. In reality, the savings will be even greater, since these are modulating circulators, which at minimum power can reach consumption of up to just 3 W. The low-consumption circulator installed in the Bluehelix K 50 has a variable flow rate, with ΔT control. The advantages o ered are many, including: System start-up from cold: faster start-up with full control of the thermal load on the components Long-lasting maintenance of the temperature equilibrium conditions, once the set point has been reached Better operation in limit conditions (e.g. at minimum power), reduction of on-oFF states Reactivity to variations in the thermal load, an appreciable quality in multi-zone systems ..ROBUST Others are the merits attributable to the circulator chosen for Bluehelix K 50: The PWM signal (pulse width modulation) to the circulator allows extremely rapid intervention times to complete an advanced and complete electronic platform. This results in a drastic reduction of the ON-OFF events of the burner and the circulator. Electronic control of the drive torque at start up with consequent reduction of the risk of blocking. The routine anti-seize cycle is in any case carried out every 24 hours of inactivity. Self-protection function in case of overheating Less noise All this translates into greater longevity not only of the circulator, but also of the components subject to wear and tear from frequent on-off cycles. COMFORT AND SAFETY The designers have thought of a series of functions capable of guaranteeing the quality of the domestic water, the best delivery of power to the heating system combined with a longer life for the appliance. SLIDING TEMPERATURE OPERATION With the installation of the “external probe” kit it is possible to operate the boiler in sliding temperature. This means that without using the system temperature adjustment keys, the boiler will self-regulate according to the variations in external temperatures. All this translates into energy savings while ensuring maximum comfort for the user. ANTI-LEGIONELLA FUNCTION In order to keep the storage cylinder in suitable hygienic-sanitary conditions, the product electronics are able to keep it at a temperature of 65°C at programmable time intervals from one to seven days. ANTI-BLOCK FUNCTION In order to avoid blockage and consequent damage to the heating circulator and the three-way diverter valve, after a set period of inactivity, the boiler electronics activate operation for a few seconds. ANTIFREEZE FUNCTION In the event that the temperature in the boiler drops to 5°C, the burner automatically turns on and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. ECONOMY/COMFORT FUNCTION By activating the appropriate key, heating/temperature maintenance can be excluded by the user (Economy). This makes it possible to reduce fuel consumption during periods of non-use of domestic water Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Savio Condensing Boiler EVOdens MAX HE 25S With 45 lt METHANE or LPG boiler Model: Evodens Max HE Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 25.0 / 30.0 kW Heating/DHW maximum useful power: 24.3 / 29.1 kW Yield name 60°/80°C: 97.0% Yield at 30% load: 107.6% High yields (**** compliant with yield directive 92/42 EEC and Legislative Decree 311/06) NOx class 6 Weighted NOx: 44 mg/kWh Minimum/maximum heating temperature: 25/85°C Minimum/maximum heating pressure 3.0/0.3 bar Expansion vessel capacity 8 l (total) Minimum/maximum domestic hot water temperature 35/60°C Boiler nominal capacity 45 l Maximum flow rate (ΔT=25K) / (ΔT=35K): 17.6 / 12.3 l/min Specific sanitary flow rate (ΔT=30 K): 15.0 l/min Voltage / Power at nominal heat input V~/ W 230/100 Degree of protection IPX5D Dimensions HxWxD 900x600x400 Power supply: methane or LPG Evodens Max HE Large and immediate production of domestic hot water despite being a small-sized boiler The EVODENS MAX HE boilers with porcelain-coated glass tank were created to satisfy the most demanding users: large and immediate production of domestic hot water despite being a small-sized boiler. The accumulation boiler , together with the latest generation condensing primary exchanger , ensure the supply of domestic hot water in continuous service always at the desired temperature. For this reason, Evodens Max HE boilers are the ideal solution for the comfort of the whole family. Characteristics: High yields (**** compliant with yield directive 92/42 EEC and Legislative Decree 311/06) Sanitary comfort (*** EN 13203) Primary condensing exchanger in stainless steel with plastic coating to offer maximum resistance to corrosion Total premix burner, built in stainless steel (Class NOx 6) Modulation 1:10 CNG and also LPG High efficiency PWM pump with low power consumption with variable speed Maximum power adjustable according to the needs of the system Glass-porcelain steel boiler with convenient flange for inspection and cleaning Removable magnesium anode External insulation of the cylinder in expanded polyurethane Standard two-litre sanitary expansion tank Degree of protection IPX5D Can be installed in a partially protected place Integration with Savio solar systems, using a solar kit Innovative digital control panel with graphic interface and buttons Digital pressure reading by pressure transducer Arrangement for remote control and external probe Possibility of remotely managing a zone valve in the case of multi-zone systems Single coil primary heat exchanger Savio produces the new Steelcoil exchanger made up of a stainless steel spiral enclosed in an aluminum shell. Thanks to the large exchange surface of the loop, a greater thermal efficiency is guaranteed with a lower pressure drop and easier cleaning. The ease of cleaning and the sturdiness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Control panel Heating temperature regulator DHW temperature regulator Digital pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display and fill guide View months left until annual maintenance is due External temperature display (with external probe connected) and signaling of external probe connected and K value set Flame modulation display Visualization of Savio SOLCONTROL solar control unit connected to Evodens Max HE, active solar pump and solar integration DHW comfort function selectable via dedicated key Direct access to the INFO menu dedicated to the user Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview BIASI rinNOVA COND XE 25S CONDENSING BOILER COMPLETE WITH LPG LPG FUME EXHAUST KIT - NEW ErP Technical specifications Model: rinNOVA COND XE 25S Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Thermal powerÿuseful sanitaryÿ(80/60ø C)ÿkW (kcal/h)ÿ26.6 (22,876) Heating capacityÿuseful heatingÿ(80/60ø C)ÿkW (kcal/h) 21.2 (18,232) Heat input(*)ÿnominalÿkW (kcal/h)ÿ25.0 (21,500) Heat inputÿminimumÿkW (kcal/h)ÿ6.0 (5,159) Sanitary flowÿt =25øKÿl/min 15.9 Dimensions (HxWxD) 700x400x290 mm Main features renew COND Xÿ RinNova Cond X The BIASI premixed condensing range completes: perfectÿfor underfloor systems for radiator systems, the compact condensing boiler that ensures high yields, low consumption and respect for the environment. Availableÿfor heating and domestic hot water production, in powers of 25 and 35 kW and forÿheating only in powers of 16, 25 and 35 kW. Characteristics: High yields (in compliance with yield directive 92/42 EEC and Legislative Decree 311/06) Sanitary comfortÿÿ(EN 13203) Primary and condensing exchanger in stainless steel with plastic linings to offer maximum resistance to corrosion Total premix burner, built in stainless steel (class NOx 5) Sanitary plate heat exchanger in stainless steel High efficiency pump with low energy consumption Maximum power adjustable according to the needs of the system Degrees of protection IPX5D Installability in a partially protected place Integration with BIASI solar systems using a solar kit digital control panel with backlit display Digital pressure reading by pressure transducer Arrangement for external probe remote control Four-controllers Summer/winter/off selector Heating temperature regulator DHW temperature regulator Digital pressure reading DHW and heating temperature visualization from display Display of fault diagnostics, fault history block status View recommended fill View annual maintenance expiry The display operates according to the modes: 1. INFO. Inf mode displays the following information: External temperature (in case of connected external probe) K value (in case of connected external probe) Sanitary / heating temperatures chosen by the user Smoke temperatures. 2. PROGRAMMING. The programming mode allows you to modify the boiler parameters. In chimney sweep mode it is possible to test the boiler and make adjustments to the gas valve. RinNova Cond XE: Adjustable maximum power The adjustable maximum useful heating power parameter meets the needs of modern construction without compromising comfort required in the production of domestic hot water. In fact, this function makes it possible to limit the maximum useful power in heating, independently of the useful domestic power. Hot water even with the sun RinNova Cond XE for heating and hot water production: the sanitary exchangerÿin stainless steel combined with the electronic management and low inertia of the primary exchangerÿdetermines excellent performance even in the production of domestic hot water.ÿFor the production of domestic hot water RinNova Cond XE can be combined with BIASI solar systems using specific solar kit (optional). The boiler cuts in only when necessary, making the most of solar energy and guaranteeing the comfort required by the user. Included in delivery: Boiler support bracket and paper template Boiler power cable Condensate collection siphon Quick instruction to the user. All ready for Energy Labeling What is it about From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres or As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. It's about me tooÿ YES, it affects everyone: professionals and end users The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier's responsibility The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. Responsibilities of Resellersÿ First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: ITEM OUT OF PRODUCTION, IN THE ABSENCE THE NEW MODEL THEMATEK CONDENS WILL BE SHIPPED Hermann Saunier Duval Thematek Condensing 25 kW condensing boiler complete with flue gas kit - Methane Model: ErP efficiency class in heating/DHW: A Sanitary load profile: XL Type: Heating and domestic hot water Fireplace power qmin/qmax kW 5.1/18.4 Fireplace min/max -60°C kW 5.1 - 25.7 Continuous flow deltaT=25K l/min 14.0 Dimensions HxWxD 740x418x300 mm Product code 0010016106 THEMATEK Wall mounted combined boiler with 18 kW in heating and 24 kW in production of domestic hot water equipped with a primary heat exchanger in anti-corrosion aluminium. Quality and durability are guaranteed by a high-efficiency pump, a total premix burner and an 8-litre expansion vessel, perfect for medium-sized systems. Thematek condensing provides instant sanitary comfort thanks to the efficient plate exchanger which guarantees the production of hot water in a precise and timely manner. Instant Health Comfort Instant boiler water in the name of efficiency Exchanger in anti-corrosion aluminum-silicon alloy High health performance Simple installation Simple and intuitive display The heart of the boiler is the aluminum-silicon primary exchanger Compact, light, highly performing. The material used enhances the excellent weight/power ratio allowing easy installation of the boiler which can be lifted by a single person and can be installed in small spaces thanks to its compactness. Heat exchange channels on all faces of the exchanger allow for uniform heat transfer, reducing stress and ensuring durability over time. Thanks to its design, the heat exchanger offers large sections with a large exchange surface which allows a lower water temperature, thus limiting the formation of limescale. User interface The user interface of the Thematek Condensing range combines aesthetics and ease of use. The keys and symbols used allow the user to intuitively understand the management of the appliance and adjust it according to one's needs. "Negative black" backlighting for greater visual contrast Easy adjustment of heating and DHW delivery temperatures Extremely intuitive menu navigation All parameters under control Simple to program Wall mounted instantaneous condensing boiler Peak flow rate up to 14 l/min (deltaT=25K of domestic hot water) Arrangement of DIN hydraulic connections Can be installed indoors or outdoors in a partially protected location Working temperature 0°C - 60°C Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview SAVIO evoDENS E 25S* CONDENSING BOILER COMPLETE WITH KIT FOR LPG METHANE FUME EXHAUST - NEW ErP Technical specifications Model:ÿevoDENS Product codeÿLPG: 103021010300 Product codeÿMETHANE: 103121017300 Characteristics of heating/sanitary exercises: Heating/DHW nominal heat inputÿ20.0 / 25.0 Minimum heating/DHW heat inputÿ6.0 Yield name 60ø/80øC % 97.4 Yield min. 60ø/80øC % 97.4 Efficiency 30% at 30°C: 101.5 Energy efficiencynøÿ Minimum / maximum heating temperature**øC 25 / 85 Minimum / maximum heating pressurebar 0.3 / 3.0 Capacity of the expansion vessel (total / useful) l 7.0 / 3.5 Minimum / maximum sanitary temperatureøC 35 / 55 Sanitary minimum / maximum pressurebarÿ0.3 / 10.0 Maximum flow rate (T=25 K) / (T=35 K) l/minÿ15.9 / 11.4 Voltage / Power at nominal heat input V ~ÿ230 ~ / 98 Power at minimum thermal capacity W 9 Power at rest (stand-by) W 5 Degrees of protection nø IPX5D Dimensions HxWxD:ÿ700x400x290 mm; 31.5 kgs Boiler water content 2.0 l Main features evoDENS The new Savidi range of high efficiency wall mounted boilers dedicated to residential buildings. A complete range of powers, 24, 28 and 32 kW, for heating and the production of domestic hot water, inÿextremely compact dimensionsÿ (700 x 400 x 325 mm) makes Evodens a product suitable for different comfort needs.ÿEvodensÿe endowed with an aesthetic innovativeÿand a newÿimmediate and simpleÿto use interface. New functions make ÿEvodens an integral part of a system and facilitate its installation. Exchangers: Primary heat exchanger in copper, high circulation lamellar. Sanitary heat exchanger in stainless steel plates digital control panel:ÿInnovative digital control panel with graphical interface and buttons Ecodesign Directive: from 2015 on new condensing boilers In fact, after very long negotiations, the ÿEcodesign regulationÿ was approved, which introduces a new energy labeling on minimum efficiency standards for boilers.ÿIn particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for appliances for the production of domestic hot water. ÿHence the obligation to installÿonly condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimneyÿas occurs in traditional boilers. The recovered heat is transferred to the heating system, making it possible to achieve a yield of 106% with 92% of the traditional boiler and 84/85% of an oldÿÿtraditional generator.ÿThe installation obligation concerns manufacturers of boilers which will no longer be able to place on the market non-condensing starting from 26 September 2015. This means that starting from this date, anyone who wants to install a boiler in their own home will have to install only condensing models. Only one particular type of non-condensing boiler will continue to be produced which is technically called open room? to be installedÿ when it is not possible to replace an old boiler with a condensing boilerÿdue to problems related to the collective flueÿof some multi-family buildings. Products for heating water and the environment represent around 30% of the world's energy consumption in Europe.ÿ Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations like Italy were deactivated. As of 26 September 2015, the ErP regulation and ÿenergy labelingÿwill be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and hot water storage tanks) u. How to read energy labels There are different labels, based on the type and function of the product (only room water heating of both, and in this case the label must bear both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise levels, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.

Read more less

IN THE ABSENCE OF THE PRODUCT, THE NEXT MODEL "MICRA 4 CONDENSING 25 MIGO" WILL BE PROPOSED WITH A DIFFERENT PRICE SAUNIER DUVAL MICRA 4 CONDENSING 25 kW METHANE GAS BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ERP Model ErP efficiency class in heating/DHW: A Sanitary load profile: XL Type: Heating and domestic hot water Combustion chamber: sealed Domestic hot water production technology: Aquaspeed® Heating Nominal power P min/max heating 80/60 °C: kW 5.4/19.1 Partial load efficiency 30% 40/30 °C %: 108.5 Sanitary Rated power min/max (60 °C): kW 5/25.2 Specific flow rate (∆T=25 K): l/min 14 Continuous flow rate (∆T=30 K): l/min 12 Min/max DHW temperature: 35/60 °C Electrical characteristics Total absorbed electric power: W 66 Supply voltage/frequency: V/Hz 230/50 Dimensions: Dimensions (h x w x d): 700 x 390 x 280 mm CNG code (G20) - 10015675 METHANE version MICRA 4 CONDENSING The Micra 4 Condensing condensing boilers, ecological and performing, meet the highest standards in terms of efficiency and comfort, thanks to the exclusive Aquaspeed® technology for the production of domestic hot water. The range includes two combined models of 25 and 30 kW and 3 heating only models of 12, 26 and 30 kW. Characteristics Energy classification 4 stars **** (92/42/EEC) with yields up to 109.2%; Sanitary comfort 3 stars ***(EN 13203-1), thanks to the Aquaspeed® system which guarantees the immediate delivery of domestic hot water at the desired temperature and the sanitary stainless steel plate exchanger with pre-heating function (Kombi models) The control panel on the boiler, with backlit liquid crystal display and negative contrast, makes adjusting Micra 4 Condensing extremely easy and immediate: with a few simple gestures it is possible to adjust the temperatures of the heating and domestic hot water, for any need . Solar Easy: all models in the Micra 4 Condensing range can be combined with solar systems, thanks to special kits. The small dimensions make all Micra 4 Condensing models perfect both for new systems and for replacement in existing systems. Continuous domestic hot water production (DHW) up to 18 l/min (Kombi models) • Low NOx emissions - class 5 (EN 483) Total premix burner and primary exchanger in anti-corrosion Aluminium-Silicon alloy High efficiency and modulating circulator Heating system antifreeze function Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Model: rinNOVA COND PLUS E 25S Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating / DHW nominal heat input kW 21.0 / 26.0 Heating / DHW maximum useful output 60°/80°C * 20.3 / 15.1 Energy yield n° **** NOx class 6 Expansion vessel capacity 7.0 l (total) Maximum range (ΔT=25K) / (ΔT=35K) 14.5 / 10.3 Degree of protection IPX5D Dimensions HxWxD 700x400x290; 33 kgs General characteristics renew COND PLUS RinNova Cond Plus is the new BIASI range of wall-mounted condensing boilers: excellent performance thanks to the new heat exchanger and ease of use thanks to the digital control panel with display. Available in versions for heating and domestic hot water production and for heating only RinNova Cond Plus presents a complete range of powers, 20 and 30 kW combi models and 16 KW SV models, in the same extremely compact dimensions (700 x 400 x 290 mm) . RinNova Cond Plus has its strong point in the innovative heat exchanger designed to provide high yields that last over time digital control panel, designed to communicate with the user in an easy and comfortable way. Like the entire BIASI condensing range, RinNova Cond Plus allows you to obtain maximum savings from climatic thermoregulation, based on the system in which the boiler is installed Characteristics: High yields (★★★★ compliant with yield directive 92/42 EEC and Legislative Decree 311/06) Sanitary comfort (★★★ EN 13203) Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion Total premix burner, built in stainless steel (Class NOx 6) Modulation 1:5 CNG and also LPG Sanitary plate heat exchanger in stainless steel 7 liter expansion vessel High efficiency pump with low energy consumption Maximum power adjustable according to the system • IPX5D degree of protection Can be installed in a partially protected place Integration with BIASI solar systems, using a solar kit Digital control panel with backlit display Analog pressure reading Arrangement for remote control and external probe. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display and fill guide View annual maintenance expiry The display operates according to the modes: 1. INFO. Info mode displays the following information: External temperature (in case of external probe connected) K value (in case of external probe connected) Sanitary / heating temperatures chosen by the user Smoke temperatures. 2. PROGRAMMING. The programming mode allows you to change the boiler parameters. - In chimney sweep mode it is possible to test the boiler and adjust the gas valve. Thermoregulation By connecting the external probe and the remote control (optional) directly to the boiler, climatic regulation can be used. RinNova Cond Plus will adapt the system water temperature to the external climatic conditions, ensuring that the desired room temperature is reached without waste and optimizing consumption. By using the climatic regulation, the regulation efficiency is also raised, giving greater value to your home. High regulation single coil primary heat exchanger Biasi introduces on the market the new stainless steel heat exchanger for condensing boilers: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single strip of stainless steel to produce the coil, including inlet/outlet fittings, the following benefits are achieved: Accumulation of dirt and debris is avoided The water flow is uniformly distributed and guarantees a homogeneous heat exchange The water flow is constant for a longer life of the product Reduction of pressure drops with optimized circuit. The ease of cleaning and the robustness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015 , the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

RIELLO START AQUA CONDENS 25 BIS METHANE CONDENSING BOILER COMPLETE WITH SMOKE KIT - NEW Erp: Start Aqua Condens is a wall-mounted boiler with a 45-litre stainless steel boiler. Technical Features Heating energy efficiency Class A Energy efficiency of sanitary equipment XL profile Class A Heating/sanitary operation features: Nominal heating heat output: 25 kW Nominal heating power (80ø/60ø):ÿ24.50 kW Nominal heating power (50ø/30ø):ÿ26.25 kW Nominal heat output for domestic hot water: 25 kW Nominal heat output for sanitary use: ÿ25 kW Energy efficiency (92/42/EEC) ÿ**** Useful efficiency Pn (50ø/30ø): ÿ105% - 108% Profitability 30% (47ø return): 107.1% Airtight chamber, forced draft Amount of hot water with t 30øC: 141 *** Amount of water drawn (litres) in 10' with ǽÓ??ÿT = 30øC Dimensions (hxwxd) mm 1005 x 450 x 600; 66 kg Electrical protection degree: IP X5D NOx class: 5 PRODUCT CODE: 20100125 Power supply: METHANE General Features START AQUA CONDENS INTERNAL Combined model with 45 litre stainless steel tank. Start Aqua Condens is a wall-mounted boiler with a 45 litre stainless steel boiler. The Riello exchanger made entirely of aluminium guarantees efficiency and durability, high prevalence and reduction of polluting emissions. It is available with a power of 25 kW. Certification or Range Rated that allows the nominal power of the boiler to be adjusted to the actual thermal needs of the system. Three-speed circulator. Standard thermoregulation on the board in combination with the external probe (optional). Assembly template, hydraulic fittings, power cable included. Standard methane operation with the possibility of conversion to LPG (G31) (accessory), this modification must be carried out by the installer of the technical assistance service. ErP: Energy related Products The new European regulations for heat generators   ErP is the acronym for “ Energy related Products ” (energy-related products) and is the abbreviation that identifies the European ErP Directive 2009/125/CE, defined by the EEC with the aim of reducing the energy consumption of products through eco-compatible design (“eco-design”). The scope of this European Directive is extremely broad as it has so far affected products such as light bulbs, air conditioners, washing machines, fans, etc. Following the publication in September 2013 of a series of implementing regulations, from 26 September 2015 it will also apply to heating and domestic hot water production products. Also from the same date, other regulations that will implement the energy labeling of the same product families will become effective. The transitional period between the publication of the regulations and their activation throughout the European Community was necessary to allow the full reception of the contents by companies and market players. Energy labelling of heating and domestic hot water products The regulations issued require that all products intended for heating and/or the production of sanitary water, with a nominal thermal power lower than or equal to 70 kW, be placed on the market with an energy label that highlights their efficiency class. Note: the regulation requires the presence of the energy label for the release of the product from factories to the market. All products previously released, for example present in distribution warehouses, can be regularly marketed even if they do not have an energy label. Different energy labels have been provided based on the use of the generator used: for heating from A++ to G; for the production of sanitary water from A to G. A new way to guide the consumer The purpose of energy labels is to allow the consumer to easily identify the efficiency level of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pump products, as has been done for air conditioners, the efficiency data is reported for the average climate range.   In addition to product energy labels, European regulations have also provided for the creation of a system label in the case of a system in which several devices, components and controls operate.   This labeling, thanks to the combinations of data from the different elements used in the system, will allow the creation of systems capable of reaching efficiency levels even higher than those of individual generators. The European regulation requires that the system label must be made available by those who supply and/or operate the system (sellers-installers); however, this option is also granted to manufacturers. Product Warranty All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

Ferroli condensing boiler Bluehelix HiTech RRT 28 H complete with low NOx methane or LPG fume exhaust kit for heating only - New Heating ERP Class A Heating capacity max / min kW 28.5 / 3.5 Yield 30% % 109.7 NOx emission class (EN 15502-1) - 6 Heating expansion vessel capacity 8 litres Protection degree (IEC 60529) IP X4D Dimensions HxWxD mm 700x420x320 Bluehelix HiTech RRT H (Heating Only) The new user interface with «capsense» technology, without mechanical keys and equipped with a 2.8'' graphic display, allows the user to interact with the product easily and extremely simply. Thanks to the energy efficiency of the space heating ηs 94% among the highest in the category (Class A ErP, scale from G to A++) and to the combination with the Connect remote control, able to read the outside temperature directly from the internet, reaches the system energy class A+ (scale from G to A+++). Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:10 (1:10 mod. 34 C, 1:9 mod. 28 C, 1:7 mod 24 C). Thanks to the "Hydrogen plug-in" system, one of its most important innovations, it is already able to self-regulate to work with mixtures of natural gas and hydrogen, which will soon arrive in Europe, to combat global warming. Conceived to fully satisfy the requests for a "robust" product from every point of view thanks to the high-passage primary exchanger capable of guaranteeing maximum efficiency and reliability over time also, and not only, as a replacement for old generators in particularly dirty systems . Silence at the top The particularly careful design of BLUEHELIX HITECH RRT has made it possible to achieve significant values ​​in terms of silence and acoustic comfort, so much so that it could almost be difficult to distinguish the background noise of a home from the noise produced by the boiler during normal operation. It will be difficult to realize whether the boiler is on or off from its noise, as on older generations of boilers, because even the on/off transients have been optimized according to acoustic comfort. The planning also took care of the design, creating a precious mantle in 3 removable pieces, which descends to cover the pipe connections Characteristics Boiler with thick stainless steel primary exchanger , with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt thanks to the combination with the CONNECT modulating remote control and the reading of the external temperature directly from the internet, it reaches the maximum energy efficiency A+ (scale from G to A+++) Class 6 NOx: already in line with the provisions of the ErP regulation from 26.09.2018 (NOx emissions < 56mg/kWh) MC2: Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) MGR: Methane LPG Ready, through a simple configuration the boiler is able to operate on both methane and LPG without the use of additional conversion kits Exclusive exchanger-burner system with self-cooled door (without insulators): simplifies maintenance and reduces its cost thanks to fewer perishable parts Instantaneous production of DHW with dedicated DHW plate heat exchanger (only for version C) Hydraulic connections covered by the boiler casing Large backlit multifunction graphic display for easy and correct parameter setting Standard by-pass Easily adapts to load conditions thanks to the wide modulation range which can reach up to 1:10 (1:10 mod. 34 C, 1:9 mod. 28 C, 1:7 mod 24 C). Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard Designed to simplify and facilitate normal maintenance and cleaning operations Predisposition for solar systems: prepared for the production of domestic hot water combined with solar panel systems ECO function in DHW for greater savings in the period of low use of hot water (only for version C) Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (only for methane operation) Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit Boiler control The new user interface with ''capsense'' technology, without mechanical keys and equipped with a 2.8'' graphic display, allows the user to interact with the product easily and extremely simply, customizing the operation of the appliance in so as to manage the environmental comfort according to one's needs. Thanks to the remote connection via bus, this can also be done directly from the CONNECT remote control, even via smartphone. The boiler is also set up to connect a second room thermostat to dedicated terminals to manage multi-zone systems. TOP EFFICIENCY Even on old systems (replacements) The BLUEHELIX HITECH RRT heat exchanger THERMOBALANCE™ (fig. A) compared to the more classic and widespread steel exchanger (fig. B) also used in the past by the Ferroli Group exclusively on a small series of boilers produced for the market English, and then immediately abandoned in favor of the evolution towards the proprietary steel exchanger used in the Bluehelix models (2012 -> ). This geometry allows the heat exchanger of the THERMOBALANCE heating unit to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig . B tends to block up much faster in the part in contact with the flame due to the reduced passage area of ​​the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values MC2 Multi Combustion Control The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). EASY MAINTENANCE Trouble-free maintenance At the time of the first maintenance, the technician can see the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the "Thermobalance"TM thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: Internal accessibility is favored by the 3-piece mantle with removable side panels. The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - The fan, offset from the burner and placed underneath, must not be disassembled to access the steel burner-exchanger group. The burner door is totally self-air-cooled and therefore does not require an insulating panel, avoiding the risk that this could be damaged or broken during disassembly for cleaning. The burner can be disassembled by loosening just 3 bolts leaving free access to the stainless steel exchanger. The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: PRODUCT DISCONTINUED --> THE NEW MODEL EXCLUSIVE GREEN E 25 WILL BE SHIPPED Beretta EXCLUSIVE GREEN HE 25 boiler Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Heating nominal heat output: 21.44 kW Classification European Directive EEC 92/42: ★ ★ ★ ★ Sanitary comfort ★ ★ ★ (EN 13203) NOx emission class: 5 (UNI EN 677) Efficiency at rated power: 98.7% Efficiency at reduced load (30%): 109.6% Total electric power: 93W Electrical protection degree: iP X5D Expansion tank capacity: 9 lt Quantity of hot water with Δt=25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min Sanitary water temperature selection range: 35 - 60°C Dimensions (hxlxp) mm 845x453x358 ; 44kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control). EXCLUSIVE GREEN HE HI-EFFICIENCY ECOLOGICAL CONDENSING WALL-MOUNTS The new Exclusive Green E condensing boilers, equipped with the innovative Beretta front exchanger, in addition to implementing the requests of the ErP standards, improve all the peculiarities confirming themselves as top of the range. Seasonal efficiency up to 94%, very wide modulation range (up to 1:10), low consumption modulating circulator with the possibility of increasing the head up to 7m and reduced consumption are some of the main features. The new Exclusive Green E boilers also offer excellent reliability and technology and, thanks to their high performance, are an excellent solution in hybrid systems with solar thermal and heat pumps. The external probe that allows you to activate the climatic thermoregulation is standard as standard. Furthermore, by adding the optional BeSMART WiFi Comfort Control kit and the LINK MODE interface board kit, Exclusive Green E constitutes a class A+ system and home comfort can be governed by remotely via APP for smartphones and tablets. The boilers are equipped with a special high-head fan designed to be able to pipe flues with Ø 60 mm or Ø 50 mm flues. Front access condensing heat exchanger ( New ! ) The Exclusive Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. Modulation 1:10 The range offers a wide range of modulation to respond to real energy needs, while simultaneously offering a high reduction in consumption. Beretta realizes this system through a totally pneumatic and therefore safe and reliable model. The electronics in fact act only on the number of fan revolutions (inlet air flow rate) without intervening on the injection of the gas quantity which is automatically sucked in. Beretta therefore introduces a new double distribution mixer: a mechanical damper with a calibrated weight which opens or closes a part of the section of the venturi so as to divide the modulation range into two stages (smaller section with low air flow rates or larger section with high air flow rates). Beretta has also developed a specific silencer in the air intake to reduce any resonances generated by the new mixer. Warranty All products for sale on our site are new and packed. The guarantee yes

Read more less

ATTENTION THIS PRODUCT IS MADE TO ORDER. SHIPPING TAKES PLACE WITHIN 10 WORKING DAYS FROM THE DATE OF PURCHASE NB THE BOILER WILL BE SUPPLIED WITH METHANE. FOR CONVERTING TO LPG, CONTACT THE AUTHORIZED AREA SERVICE CENTER IN ADVANCE RIELLO RESIDENCE EXTERNA CONDENS 25 KIS LPG CONDENSING BOILER COMPLETE WITH FUME KIT - NEW ErP Technical features Product code: 20096734 specific energy label according to the European directive ErP Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Firebox thermal power (heating): 25 kW Useful thermal power (sanitary): 25 kW Energy efficiency (92/42/EEC) **** Useful efficiency at Pn* (50°C-30°C): 105% Profit return 30% (47th return): 109.6% Sealed chamber, forced draught Quantity of hot water with Δt 25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxwxd) mm 785 x 553 x 275 ; 44 kgs Electrical protection degree: IP X5D NOx class: 5 Power supply: LPG. Remote control panel (supplied): offers the possibility of controlling boiler operation without directly accessing it.   General characteristics RESIDENCE EXTERNAL CONDENS Yield **** Low polluting emissions Aluminum condenser, with premix burner Heating only models and combined models For outdoor installations Residence Externa Condens is specifically designed for outdoor installation and stands out for its extremely small dimensions. Equipped as standard with the exclusive Riello condensing exchanger, completely made of aluminum and without welding, synonymous with efficiency and durability, resistant to system dirt with high heads and excellent heat exchange. The climatic regulation is managed directly via the boiler board: this allows the temperature of the heating system to be suitably adapted to the external climatic conditions. Residence Externa Condens is controlled directly from inside the home thanks to the exclusive remote control supplied as standard. Residence Externa Condens is available with powers from 20 to 32 kW. Remote control panel supplied as standard: Modulation ratio 1:8 which allows the boiler to respond to all heat requests. Self-modulating circulator, low consumption (IEE≤0.20). Antifreeze function that protects the heating and DHW circuits down to -5°C with the possibility of extending the protection down to -15°C (optional). "Winter with Pre-heating" function: allows the DHW exchanger to be kept at the right temperature, reducing waiting times during withdrawal (instantaneous combined models). Possible "open-air" installation using the special waterproof kit (optional) Standard thermoregulation on the card in combination with the external probe (optional) Assembly template, hydraulic fittings, power supply cable supplied ErP: Energy related Products The new European regulations for heat generators ErP is the acronym of “ Energy related Products ” (products connected to the use of energy) and is the abbreviation that identifies the European Directive ErP 2009/125/EC, defined by the EEC with the intention of reducing the energy consumption of products through eco-compatible design ("eco-design "). The field of action of this European Directive is extremely broad as up to now it has involved products such as light bulbs, air conditioners, washing machines, fans, etc. Following the publication in September 2013 of a series of implementing regulations, starting from 26 September 2015 it will also apply to heating products and the production of domestic hot water. From the same date, other regulations will also become effective which will implement the energy labeling of the same product families. The transitional period between the publication of the regulations and their activation throughout the territory of the European Community was necessary to allow the full implementation of the contents by companies and market players. The energy labeling of products for heating and domestic hot water production The regulations issued require that all products intended for heating and/or for the production of domestic hot water, with a nominal thermal power lower than or equal to 70 kW, are placed on the market with an energy label that highlights their efficiency class. Note: the regulation provides for the mandatory presence of the energy label for the release of the product from the factories to the market. All products previously introduced, for example present in distribution warehouses, can be regularly marketed even if they do not have an energy label. Various energy labels have been provided based on the use of the generator used: for heating from A++ to G; for the production of domestic hot water from A to G. A new way to guide the consumer The purpose of energy labels is to allow the consumer to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pump products, as has been done for air conditioners, the efficiency figure is reported for the average climatic range.   In addition to the product energy labels, the European regulations have also provided for the creation of a system label in the event that a plant is created in which various appliances, components and controls operate.   This labelling, thanks to the combinations of the data of the various elements used in the plant, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual generators. The European regulation states that the system label must be made available by whoever supplies and/or puts the system into operation (sellers-installers); however, this option is also granted to builders.   Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

optional box Savio Edilia HE 25 built-in methane condensing boiler complete with low NOx flue exhaust kit Cassone Optional Model: Edilia HE Natural gas product code 10312.1032.1 Energy class A ErP specifications Heating/DHW nominal heat input 21.0 / 26.0 kW Heating/DHW maximum useful power 60°/80°C * 20.3 / 25.1 kW Energy Efficiency ★★★★ NOx class 6 Minimum/maximum heating pressure bar 0.3 / 3.0 Minimum/maximum DHW pressure bar 0.3 / 10.0 Degree of protection n° IPX5D Height x Width x Depth mm 1200x600x240 EDILIA Edilia HE is the new Savio range of built-in condensing boilers . Excellent performance and high yields that last over time thanks to the innovative heat exchanger. Ease of use thanks to the digital control panel with display designed to communicate with the user easily and comfortably. Available in versions for heating and domestic hot water production Edilia HE presents a complete range of powers, 20 and 35 kW combi models in the same extremely compact dimensions: 1200 x 600 x 240 mm. Both versions of Edilia HE are in class A , therefore they benefit from the tax deduction according to current legislation. Main features High yields (★★★★ compliant with yield directive 92/42 EEC and Legislative Decree 311/06) Sanitary comfort (★★★ EN 13203) Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion Total premix burner, built in stainless steel (Class NOx 6) Modulation 1:5 CNG and also LPG Sanitary plate heat exchanger in stainless steel 7 l expansion vessel for mod. 25S and 10 l for mod. 35S High efficiency pump with low energy consumption Maximum power adjustable according to the system Degree of protection IPX5D Recessed installation in the wall Integration with Savio solar systems, using a solar kit Digital control panel with backlit display Analog reading of the pressure on the machine, digital on the remote Arrangement for remote control (optional) and external probe as standard High circulation single coil primary heat exchanger Savio introduces the new stainless steel heat exchanger for condensing boilers to the market: Round . Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single stainless steel strip to produce the coil, including inlet/outlet fittings, the following benefits are achieved: Accumulation of dirt and debris is avoided The water flow is uniformly distributed and guarantees a homogeneous heat exchange The water flow is constant for a longer life of the product Reduction of pressure drops with optimized circuit The ease of cleaning and the sturdiness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations . Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. Thermoregulation By connecting the external probe (standard) and the remote control (optional) directly to the boiler, climatic regulation can be used. Edilia HE will adapt the system water temperature to the external climatic conditions, ensuring that the desired room temperature is reached without waste and optimizing consumption . By using the climatic regulation, the regulation efficiency is also raised, giving greater value to your home . Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less