Overview CHAFFOTEAUX URBIA GREEN Ebus2 25 EU CONDENSING BOILER Cod. 3310407, COMPLETE WITH FUME EXHAUST KIT - NEW ErP: Wall-mounted condensing boilers with 4 liter mini-accumulator. Technical specifications Product code: 3310407 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Rated heat output max/min (Hi) Qn:ÿ22/2,5ÿkW Useful heating power80§ C/ 60§ C max/minÿ21,5/2,4ÿkW Useful heating power50§ C/ 30§ C max/minÿ23,4/2,6ÿkW Sanitary nominal thermal power max/min (60/80§C) PCI:ÿ25/ 5.5 kW Efficiency at nominal heat input:ÿ97.8% Efficiency 30% of nominal heat input:ÿ109.1% Energy efficiency stars: (dir 92/42/CEE) **** Capacity of the expansion vessel: 8 lt Maximum system water capacity: 100/300 litres Sanitary comfort stars(EN13203): *** Port. specific in healthcare (10 min. with T= 30øC): 13.2 l/min Hot water flow rate at T 25§ C: 14.6 l/min Degrees of protection for the electrical system:ÿIPX5D Nox class: 5 Dimensions hxwxd: mmÿ745 x 440 x 375ÿ; 42kg LPG fuel supply Features list URBIA GREEN Ebus2 EU Urbia Green is the ideal solution for all homes where the best performance is required. It is a concentration of advantages in terms of sanitary comfort with reduced dimensions and consumption. Thanks to condensing technology and integration with solar systems, it maximizes energy savings and the 4-litre sanitary reserve satisfies the needs of the most demanding users. Sanitary comforts Mini-accumulintegrated in 316L stainless steel of 4 liters. Domestic hot water performance ***, maximum level unexpected by the EN 13203 standard. Flow rate from 14.6 to 19.3 l/min with T = 25§C. DHW production controlled by a modulating turbine to respond to needs without waiting times and at a constant temperature, even when extractions are very low. DHW programmer to control the tank heating time slots Eco-Delta System: DHW load system with 4 liter reserve to further improve the comfort of DHW production and new ecological functions which allow you to save energy in DHW mode. Heating comfort Efficiencyfinal 108% with energy savingsfinal 35%. 4-star combustion efficiency according to the EN 92/42 standard. SRA function, automatic boiler regulation system according to heating requirements. Modulation wide range, from 10% to 100% of the maximum power. Reduced polluting emissions, NOx class 5. Pressure sensor of the heating circuit with visualization on LCD display. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the room and/or outside temperature. Arrangement for integration into a heating system via the newÿEbus2 communication protocolÿ(boilers, solar, system management modules, modulating thermoregulation accessories). Multifunction LCD display with display: history, self-diagnosis, operating temperature. Filling taps integrated in the boiler. Convenience of installation use Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier start-up: automatic purge function and directly accessible combustion adjustment. Save energy and respect the environment Final 25% energy savings in combination with Expert Control and the SRA function. Final 35% energy savings combine and Expert Control, the SRA function, the external probe and the radiant floor. 40% reduction in CO2 emissions**. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

CHAFFOTEAUX INOA GREEN Ebus2 29 EU CONDENSING BOILER Product code: 3310478 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Nominal heat input in heating/DHW max/min (Hi): 29/6 kW Max/min heating thermal power (80°C-60°C): 28.4/5.8 kW DHW max/min thermal power: 28.4/5.8 kW Efficiency at nominal heat input: 97.7% Efficiency at 30% of the nominal heat input: 108% Energy efficiency stars: (dir 92/42/CEE) **** Expansion vessel capacity: 8 l Sanitary comfort stars (EN13203): ** Port. specific in healthcare (10 min. with ΔT= 30°C): 13.2 l/min Hot water flow rate at ∆T 25º C: 16.3 l/min Electrical system protection degree: IPX5D Extremely compact dimensions hxwxd: mm 745x400x315 ; 27kg METHANE power supply INOA GREEN Ebus2 EU The new compact condensing boiler with aluminum alloy condensing exchanger and with all the necessary requirements to achieve the required standards in terms of energy saving. Operation only methane. Sanitary comfort Sanitary heat exchanger in stainless steel. Domestic water performance: stars **. Flow rate 13.1 litres/minute with ΔT = 25ºC. (24kW) Heating comfort Efficiency up to 108% with energy savings up to 35%. 4-star combustion efficiency in compliance with the EN92/42 standard. Modulation range from 25% to 100% of maximum power. Condensing exchanger in aluminum alloy. Reduced polluting emissions, NOx class 5. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Arrangement for integration into a heating system via Ebus 2 communication protocol (boilers, solar, system management modules and modulating thermoregulation accessories). Possibility of managing single-temperature and multi-temperature zones only via Expert Control. Self-diagnosis system by code. LCD display. Comfort of use and installation Possibility of connection with external probe. Compatible with Expert Control, modulating accessories and on/ff. Easier starting: automatic purge function and directly accessible combustion regulation. Energy saving and respect for the environment Up to 20% energy savings in combination with chronothermostat and external probe. 40% reduction in CO 2 emissions **. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months

Read more less

Technical features Product code: 3310617 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XXL Characteristics of heating/DHW operation: Max/min heating nominal heat input (Hi): 31/3.5 kW DHW nominal heat input max/min (Hi): 30.0/3.5 kW Performance Stars **** Expansion tank capacity 8 l Instantaneous quantity of hot water (∆T=25 K): l/min 19.8 Domestic water pressure max/min bar 7.0/0.2 Electrical characteristics Supply voltage/frequency: V/Hz 230/50 IP X5D degree of protection Dimensions Weight: 34.6kg General characteristics AIM ADVANCE Mira Advance is the condensing boiler born for the future with a powerful soul, Spin Tech, the new exchanger with a completely renewed design that offers high performance, to improve domestic comfort and adapt to every need. Maximum Performance: New single coil primary heat exchanger in stainless steel. Passage sections increased by 142% compared to the previous version. 1 m more head. Seasonal yield at 94%. Class A+ reachable with thermoregulation. Maximum Comfort Modulation ratio 1:10. Electronic combustion control E-Burning System. SRA function. Gas transformation from the technical menu without the need for a kit. Ready for Chaffolink connectivity. Ease of Installation Installation in partially protected places. Smoke outlets 80, 60, 50 mm. Intuitive electrical connections. Energy saving and respect for the environment Up to 25% energy savings in combination with Expert Control and the SRA function. Up to 35% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015 , the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

CHAFFOTEAUX PIGMA GREEN BOILER IN Ebus2 25 EU Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Nominal heat input in heating max/min (Hi) Qn : 22/5.5 kW Useful heat output 80/60°C in heating/DHW max/min: 21.5/5.4 kW Nominal heat input in DHW (60/80°C) max/min: 26/5.5 kW Efficiency at nominal heat input: 97.5% Efficiency at 30% of the nominal heat input: 109% EN13203 sanitary comfort performance stars: *** Energy efficiency stars: (dir 92/42/CEE) **** Expansion vessel capacity: 8 l Port. specific in healthcare (10 min. with ΔT= 30°C): 12.2 l/min Minimum withdrawal: <2 l/min Total absorbed electric power: 78 W Electrical system protection degrees: IP X5D Boiler dimensions hxwxd: mm 771x502x238 ; 30kg Built-in dimensions hxwxd: mm 1140x590x240 Natural gas supply PIGMA GREEN IN Ebus2 EU It is the built-in condensing boiler, with very small dimensions, designed to guarantee exceptional sanitary comfort and high heating performance while respecting the environment and reducing consumption to a minimum. The built-in unit in sheet metal and the wide range of accessories allow simple and totally concealed installation. Designed to also manage systems with solar integration or with different heating needs in different zones, Pigma Green in Ebus 2 allows you to control the entire system using the Expert Control system manager supplied as standard. Sanitary comfort Increased plate heat exchanger in stainless steel. 3 stars for sanitary comfort, the maximum required by the EN 13203 standard. 12 l/min (ΔT= 30°C) of domestic hot water flow, measured in compliance with the EN 625 standard. DHW circuit managed by four probes and a flowmeter, to eliminate waiting times and have a constant temperature, even in the case of small withdrawals. Perfectly integrable with thermal solar systems, forced and natural circulation Daily and weekly hourly programming of the DHW exchanger pre-heating periods directly from the Expert Control system manager. Heating comfort Efficiency up to 109% with energy savings up to 35%. 4-star combustion efficiency according to EN 92/42 standard. Automatic regulation system, which can be activated directly from the Remote Control, to obtain the best operating regime in heating in all environmental conditions. Useful thermal power up to 23.5 kW. Modulation ratio 1:5. Reduced polluting emissions, NOx class 5. Heating circuit pressure sensor with display on Expert Control. Modulating circulator to improve acoustic comfort and reduce electricity consumption. Differentiated climatic thermoregulation of 3 circuits, according to the ambient and external temperature. Operation management and programming using the Expert Control system manager: operating modes and temperatures, self-diagnosis, daily and weekly programming, adjustment information and history of the latest faults. Comfort of use and installation Semi-automatic filling that can be activated by the Expert Control system manager. Expert Control system manager and external probe as standard. Adjustment of the operating parameters directly to the Expert Control system manager. Prepared for the control of system management modules up to 3 circuits at different temperatures. Prepared for the management and integration of thermal solar systems (standard solar probe). IPX5D electrical protection degree and guaranteed operation up to -15°C **. Easy commissioning: automatic de-aeration function and combustion regulation with direct access. Mechanical pressure gauge and filling cock to allow maintenance even without electricity. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Product code: 3310617 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XXL Characteristics of heating/DHW operation: Max/min heating nominal heat input (Hi): 31/3.5 kW DHW nominal heat input max/min (Hi): 30.0/3.5 kW Performance Stars **** Expansion tank capacity 8 l Instantaneous quantity of hot water (∆T=25 K): l/min 19.8 Domestic water pressure max/min bar 7.0/0.2 Electrical characteristics Supply voltage/frequency: V/Hz 230/50 IP X5D degree of protection Dimensions Weight: 34.6kg General characteristics AIM ADVANCE Mira Advance is the condensing boiler born for the future with a powerful soul, Spin Tech, the new exchanger with a completely renewed design that offers high performance, to improve domestic comfort and adapt to every need. Maximum Performance: New single coil primary heat exchanger in stainless steel. Passage sections increased by 142% compared to the previous version. 1 m more head. Seasonal yield at 94%. Class A+ reachable with thermoregulation. Maximum Comfort Modulation ratio 1:10. Electronic combustion control E-Burning System. SRA function. Gas transformation from the technical menu without the need for a kit. Ready for Chaffolink connectivity. Ease of Installation Installation in partially protected places. Smoke outlets 80, 60, 50 mm. Intuitive electrical connections. Energy saving and respect for the environment Up to 25% energy savings in combination with Expert Control and the SRA function. Up to 35% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015 , the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview CHAFFOTEAUX PIGMA 30 CF EU BOILER Cod. 3310441 - NEW ErP 2016: Pigma, wall-mounted open chamber boiler, which thanks to its compact dimensions, sanitary comfort guaranteed by 3 performance stars and digital display technology, manages to create a comfortable environment, suitable for every type of requirement and?Ó?installation. Technical specifications Product code: 3310441 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary energy efficiencyClass B Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Nominal heat output in heatingÿmax/min:ÿ29.5/ 13ÿkW Useful heating power max/min:ÿ26.7/ 11.2ÿkW Nominal thermal power max/min (sanitary) PCI:ÿ30.5/ 13ÿkW Max/min power in DHW mode:ÿ27.6/ 11.2ÿkW Efficiency at nominal heat input: 90.6% Efficiency 30% of nominal heat input:ÿ89.7% Outlet temperature range min/max temp.:ÿ35-85øC Sanitary comfort performance starsEN13203: *** Capacity of the expansion vessel: 8 lt Maximum system water capacity: 100/300 litres Port. specific in healthcare (10 min. with T= 30øC): 13.5 l/min Hot water flow rate at T 25§ C: 15.8 l/min Maximum absorbed power: 62W Electrical protection degrees: IP X4D Dimensions hxwxd: mmÿ745x400 x307ÿ; 31kg ÿMETHANEÿorÿLPG power supply Propan methane conversion kit supplied Features list PIGMA Ebus2 EU Thanks to the compact dimensions, the sanitary comfort guaranteed by the 3 performance stars and the digital display technology that allows optimal management of the heating, Pigma manages to create a comfortable environment, suitable for every type of need and installation Sanitary comforts Sanitary heat exchanger in oversized stainless steel. Domestic hot water performance ***, maximum level unexpected by the EN 13203 standard. Flow rate from 14.2 to 15.8 l/min with T = 25§C. Controlled DHW production managed by two probes and a sanitary flowmeter for better temperature stability based on the type of withdrawal. Programmable on/off comfort function. Heating comfort 3 star efficiency of combustion in compliance with the EN92/42 standard. SRA function, automatic boiler regulation system according to heating requirements. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the room and/or outside temperature. Arrangement for integration into a heating system via the new Ebus2ÿ communication protocol (boilers, solar, system management modules, modulating thermoregulation accessories). Backlit LCD display with display: history, self-diagnosis, operating temperatures Convenience of installation use Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier start-up: automatic purge function and directly accessible combustion adjustment. Compact and perfectly adaptable to any type of home. Save energy and respect the environment Final 15% energy savings in combination with Expert Controlÿmodulating room probe andÿthe SRA function. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.

Read more less

Product code: 3310337 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Nominal max/min heat output (Hi) Qn : 31/7.0 kW Useful heating power 80º C/ 60º C max/min 30.3/6.7 kW Useful heating output 50º C/ 30º C max/min 33.1/7.4 kW DHW nominal thermal power max/min (60/80ºC) PCI: 35/ 6 kW Efficiency at nominal heat input: 97.6% Efficiency at 30% of the nominal heat input: 108.7% Energy efficiency stars: (dir 92/42/CEE) **** Expansion vessel capacity: 10 l Maximum water capacity of the system: 100/300 litres Sanitary comfort stars (EN13203): *** Specific flow rate in accordance with EN 625 at Δt 30ºC : 23 l/min Hot water flow rate at ∆T 35º C: 19.7 l/min Hot water flow rate at ∆T 25º C : 27.6 l/min Maximum absorbed power; W 77 Electrical system protection degree: IPX5D Nox class: 5 Dimensions hxwxd: mm 900 x 600 x 465 ; 60kg METHANE power supply NIAGARA C GREEN Ebus2 EU Condensation associated with sanitary comfort (2 20-litre boilers) integrated in just 60 cm wide for total comfort. Power, compact dimensions and high technology for the most demanding. Sanitary comfort 40 liter reserve thanks to 2 standard stainless steel inter-accumulators. Stratified storage tanks: the advantage of domestic hot water storage and instantaneous production. Permanent availability of domestic hot water even if the accumulated hot water reserve runs out. Power optimization thanks to a continuous modulation of the DHW pump flow rate. Domestic hot water performance ***, maximum level foreseen by the EN 13203 standard. Flow rate of 27.6 l/min with ΔT = 25ºC. Integrated 2-litre sanitary expansion tank. Heating comfort 4-star combustion efficiency in compliance with the EN92/42 standard. High modulation range from 25% to 100%. Total premix modulating burner and stainless steel heat exchanger. Modulating fan and pump to improve acoustic comfort and reduce energy consumption. Climatic thermoregulation for the management of 2 circuits, according to the ambient and/or external temperature for greater comfort and greater energy savings. Front panel programming with drop-down menu: history, permanent self-diagnosis, operating temperature, weekly programming and display of all information on the settings. SRA function, automatic boiler regulation system according to heating requirements. Comfort of use and installation Easy component management: common internal layout with the rest of the Chaffoteaux range. Easier starting: automatic purge function and directly accessible combustion regulation. Easy maintenance: all components are accessible from the front. Complete solar system regulation (with optional solar clip in). Energy saving Up to 23% energy savings in combination with Easy Control and the SRA function. 40% reduction in CO 2 emissions **

Read more less

Technical features Product code: 3310399 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating maximum thermal power (DHW): 21.5 (25.4) kW Nominal heat output in heating max/min (Hi) Q: 22/5.5kW Efficiency at nominal heat input: 97.8% Efficiency at 30% of the nominal heat input: 109% EN13203 sanitary comfort performance stars: *** Energy efficiency stars: (dir 92/42/CEE) **** Expansion vessel capacity: 8 l Maximum water capacity of the system: 100/300 litres Port. specific in healthcare (10 min. with ΔT= 30°C): 12.2 l/min Hot water flow rate at ∆T 25º C: 14.5 l/min Extremely compact dimensions hxwxd: 745 x 400 x 307 mm; 32kg METHANE power supply To view more product information CLICK HERE General characteristics PIGMA GREEN Ebus2 EU The ideal condensing range for replacement with the aim of improving efficiency. The energy savings of condensing technology and the best sanitary comfort solutions, all concentrated in just 40 cm of intelligence. A complete range of accessories facilitates installation and use in advanced systems thanks also to the simplicity of integration with solar thermal systems. Sanitary comfort Sanitary heat exchanger in stainless steel. Domestic hot water performance ***, maximum level foreseen by the EN 13203 standard. Flow rate from 14.5 to 19.3 l/min with ΔT = 25ºC. Controlled DHW production managed by two probes and a sanitary flowmeter for better temperature stability based on the type of withdrawal. Programmable comfort function. Heating comfort Efficiency up to 109% with energy savings up to 35%. 4-star combustion efficiency in compliance with the EN92/42 standard. Modulation range from 20% to 100% of maximum power. SRA function, automatic boiler regulation system according to heating requirements. Reduced polluting emissions, NOx class 5. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the ambient and/or external temperature. Arrangement for integration into a heating system via the new Ebus 2 communication protocol (boilers, solar, system management modules and modulating thermoregulation accessories). Backlit LCD display with display: history, self-diagnosis, operating temperatures. Comfort of use and installation Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier starting: automatic purge function and directly accessible combustion regulation. Can be installed in partially covered places. Energy saving and respect for the environment Up to 25% energy savings in combination with Expert Control and the SRA function. Up to 35% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. 40% reduction in CO 2 emissions **. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Product code: 3310400 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Characteristics of heating/DHW operation: Heating maximum thermal power (DHW): 27.3 (29.3) kW Nominal heat output in heating max/min (Hi) Q: 28/6.5 kW Efficiency at nominal heat input: 97.6% Efficiency at 30% of the nominal heat input: 108.2% EN13203 sanitary comfort performance stars: *** Energy efficiency stars: (dir 92/42/CEE) **** Expansion vessel capacity: 8 l Maximum water capacity of the system: 100/300 litres Port. specific in healthcare (10 min. with ΔT= 30°C): 14.1 l/min Hot water flow rate at ∆T 25º C: 16.8 l/min Extremely compact dimensions hxwxd: 745 x 400 x 375 mm; 35kg LPG power supply To view more product information CLICK HERE General characteristics PIGMA GREEN Ebus2 EU The ideal condensing range for replacement with the aim of improving efficiency. The energy savings of condensing technology and the best sanitary comfort solutions, all concentrated in just 40 cm of intelligence. A complete range of accessories facilitates installation and use in advanced systems thanks also to the simplicity of integration with solar thermal systems. Sanitary comfort Sanitary heat exchanger in stainless steel. Domestic hot water performance ***, maximum level foreseen by the EN 13203 standard. Flow rate from 14.5 to 19.3 l/min with ΔT = 25ºC. Controlled DHW production managed by two probes and a sanitary flowmeter for better temperature stability based on the type of withdrawal. Programmable comfort function. Heating comfort Efficiency up to 109% with energy savings up to 35%. 4-star combustion efficiency in compliance with the EN92/42 standard. Modulation range from 20% to 100% of maximum power. SRA function, automatic boiler regulation system according to heating requirements. Reduced polluting emissions, NOx class 5. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the ambient and/or external temperature. Arrangement for integration into a heating system via the new Ebus 2 communication protocol (boilers, solar, system management modules and modulating thermoregulation accessories). Backlit LCD display with display: history, self-diagnosis, operating temperatures. Comfort of use and installation Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier starting: automatic purge function and directly accessible combustion regulation. Can be installed in partially covered places. Energy saving and respect for the environment Up to 25% energy savings in combination with Expert Control and the SRA function. Up to 35% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. 40% reduction in CO 2 emissions **. All ready for Energy Labeling What is it about? From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy-intensive sectors: construction For placing on the European market, the eco-design directive ( ErP known as « Energy Related Products ») imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labeling of products with a capacity of less than 70 kW will give consumers simple, recognizable information which allows for comparisons on the performance and energy consumption of the product you wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. Is it about me too? YES, it affects everyone: professionals and end users The information indicated on the energy label will allow professionals to recommend the right product and individuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015 , the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier responsibility The company that supplies the product on the market is required to equip its devices or systems with the following documentation: product energy label; technical product sheet; system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices; technical data sheet of the system with the parts relating to the product or system already completed. Dealer Responsibility First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device and/or system to the public. Therefore even professionals such as plumbers, installers or planners can fall into this category. Everyone is required to ensure that: all appliances and/or systems have their respective labels and make sure that they are clearly visible; all devices and/or systems are always accompanied by the mandatory technical data sheets; any type of advertising, promotional or technical material showing energy data or price indications contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and hot water production will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP) : The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL Depending on the type of device, there are different labels. Those with efficiency classes A, A+ and A++ certify the products with the highest performance. Furthermore, two different classifications are envisaged for domestic heating and for the hot water production service, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the final customer can make his choice in the most informed way possible. SYSTEM LABEL In addition to the product label, the system label is also provided if a series of matched appliances is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label in order to inform the end user in the best possible way. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview CHAFFOTEAUX PIGMA GREEN 35 EU CONDENSING BOILER Cod. 3310401 - NEW ErP 2015, SEALED CHAMBER COMPLETE WITH FUME EXHAUST KIT: wall-mounted condensing boilers with microaccumulator. Technical specifications Product code: 3310401 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Heating maximum thermal power (DHW):ÿ30.2 (33.7)ÿkW Nominal heat output heatingÿmax/min (Hi) Q:ÿ31/7.0ÿkW Efficiency at nominal heat input:ÿ97.6% Efficiency 30% of nominal heat input:ÿ107.9% Sanitary comfort performance starsEN13203: *** Energy efficiency stars: (dir 92/42/EEC) **** Capacity of the expansion vessel: 8 lt Maximum system water capacity: 100/300 litres Port. specific in healthcare (10 min. with T= 30øC): 16 l/min Hot water flow rate at T 25§ C: 19.3 l/min Extremely compact dimensions hxwxd: mmÿ745 x 400 x 375 ; 35kg METHANE power supply Features list PIGMA GREEN Ebus2 EU Theÿcondensing rangeÿideal for replacement with the aim of improvingÿefficiency. The energy savings of condensing technology and the best sanitary comfort solutions, all concentrated in just 40 cm of intelligence. A complete range of accessories facilitates installation and use of advanced systems thanks also to the simplicity of integration with thermal solar systems Sanitary comfort Sanitary heat exchanger in stainless steel. Domestic hot water performance ***, maximum level not foreseen by the EN 13203 standard. Flow rate from 14.5 to 19.3 l/min with T = 25§C. Controlled DHW production managed by two probes and a sanitary flowmeter for better temperature stability based on the type of withdrawal. Programmable comfort function. Heating comfort Efficiencyfinal 109% with energy savingsfinal 35%. 4 star efficiency of combustion in compliance with the EN92/42 standard. Modulation range from 20% to 100% of maximum power. SRA function, automatic boiler regulation system according to heating requirements. Reduced polluting emissions, NOx class 5. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the room and/or outside temperature. Arrangement for integration into a heating system via the new communication protocolÿEbus2ÿ (boilers, solar, system management modules, modulating thermoregulation accessories). Backlit LCD display with display: history, self-diagnosis, operating temperatures. Convenience of installation use Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier start-up: automatic purge function and directly accessible combustion adjustment. Can be installed in partially covered places. Save energy and respect the environment Final 25% energy savings in combination with Expert Control and the SRA function. Final 35% energy savings by combining Expert Control, the SRA function, the external probe and the radiant floor. 40% reduction in CO2 emissions**. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview CHAFFOTEAUX URBIA GREEN Ebus2 25 EU CONDENSING BOILER Cod. 3310407, COMPLETE WITH FUME EXHAUST KIT - NEW ErP: Wall-mounted condensing boilers with 4 liter mini-accumulator. Technical specifications Product code: 3310407 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Rated heat output max/min (Hi) Qn:ÿ22/2,5ÿkW Useful heating power80§ C/ 60§ C max/minÿ21,5/2,4ÿkW Useful heating power50§ C/ 30§ C max/minÿ23,4/2,6ÿkW Sanitary nominal thermal power max/min (60/80§C) PCI:ÿ25/ 5.5 kW Efficiency at nominal heat input:ÿ97.8% Efficiency 30% of nominal heat input:ÿ109.1% Energy efficiency stars: (dir 92/42/EEC) **** Capacity of the expansion vessel: 8 lt Maximum system water capacity: 100/300 litres Sanitary comfort stars(EN13203): *** Port. specific in healthcare (10 min. with T= 30øC): 13.2 l/min Hot water flow rate at T 25§ C: 14.6 l/min Degrees of protection for the electrical system:ÿIPX5D Nox class: 5 Dimensions hxwxd: mmÿ745 x 440 x 375ÿ; 42kg METHANE power supply Features list URBIA GREEN Ebus2 EU Urbia Green is the ideal solution for all homes where the best performance is required. It is a concentration of advantages in terms of sanitary comfort with reduced dimensions and consumption. Thanks to condensing technology and integration with solar systems, it maximizes energy savings and the 4-litre sanitary reserve satisfies the needs of the most demanding users. Sanitary comforts Mini-accumulintegrated in 316L stainless steel of 4 liters. Domestic hot water performance ***, maximum level not foreseen by the EN 13203 standard. Flow rate from 14.6 to 19.3 l/min with T = 25§C. DHW production controlled by a modulating turbine to respond to needs without waiting times and at a constant temperature, even when extractions are very low. DHW programmer to control the tank heating time slots Eco-Delta System: DHW load system with 4 liter reserve to further improve the comfort of DHW production and new ecological functions which allow you to save energy in DHW mode. Heating comfort Efficiencyfinal 108% with energy savingsfinal 35%. 4-star combustion efficiency according to the EN 92/42 standard. SRA function, automatic boiler regulation system according to heating requirements. Modulation wide range, from 10% to 100% of the maximum power. Reduced polluting emissions, NOx class 5. Pressure sensor of the heating circuit with visualization on LCD display. High efficiency circulator with continuous modulation to improve acoustic comfort and reduce energy consumption. Differentiated climatic thermoregulation of 2 circuits, according to the room and/or outside temperature. Arrangement for integration into a heating system via the newÿEbus2 communication protocolÿ(boilers, solar, system management modules, modulating thermoregulation accessories). Multifunction LCD display with display: history, self-diagnosis, operating temperature. Filling taps integrated in the boiler. Convenience of installation use Compatible with Expert Control: intuitive system manager for the management of 3 circuits, according to the room and/or outside temperature for greater comfort and greater energy savings. New intuitive electrical connections. Easier start-up: automatic purge function and directly accessible combustion adjustment. Save energy and respect the environment Final 25% energy savings in combination with Expert Control and the SRA function. Final 35% energy savings combine and Expert Control, the SRA function, the external probe and the radiant floor. 40% reduction in CO2 emissions**. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview CHAFFOTEAUX ALIXIA GREEN IN EBUS2 24 EU CONDENSING BOILER Cod. 3310442, COMPLETE WITH FUME EXHAUST KIT - NEW ErP 2015: Alixia In Green is the most current interpretation of condensing technology. Thanks to the built-in unit in sheet metal, it represents the ideal solution for recovering living space, while still guaranteeing practicality of use thanks to the Expert Control system manager. Technical specifications Product code: 3310442 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Nominal heat input in heating/sanitary max/min (Hi):ÿ23.5/4.5ÿkW Heating max/min thermal power (80øC-60øC):ÿ23/4,4ÿkW Sanitary nominal heat input(60/80øC) max/min:ÿ23.5/4.5ÿkW Efficiency at nominal heat input:ÿ97.7% Efficiency 30% of nominal heat input:ÿ108.4% Energy efficiency stars: (dir 92/42/EEC) **** Capacity of the expansion vessel: 8 lt Sanitary comfort stars(EN13203): *** Port. specific in healthcare (10 min. with T= 30øC): 10.3 l/min Degrees of protection for the electrical system:ÿIPX5D Total absorbed electrical power: 91 W Boiler dimensions hxwxd: mmÿ771x502x238ÿ; 32kg Dimensions built-inxwxd: mmÿ1140x590x240 LPG fuel supply Features list ALEXIA GREEN IN Ebus2 EU Designed to meet the regulations on energy saving and emission reduction, Alixia In Green is the most current interpretation of condensing technology. Thanks to the built-in sheet metal unit, it represents the ideal solution for recovering living space, while guaranteeing practicality of use thanks to the Expert Control system manager (standard). LPG operation. Sanitary comforts Customization of sanitary comfort from Clima Control. Sanitary heat exchanger in stainless steel. Sanitary flow rate of 12 l/min (T= 30øC) according to standard EN625. Sanitary circuit managed by two probes and a sanitary flowmeter for better temperature stability based on the type of sampling. Heating comfort Efficiencyfinal 108% on PCI with energy savingsfinal 35%. 4-star combustion efficiency according to the EN 92/42 standard. Useful thermal power up to 23.5 kW. Modulation wide range, from 25% to 100% of the maximum power. Reduced polluting emissions, NOx class 5. Climatic thermoregulation, as a function of the ambient and external temperature as standard. Operation management via digital display: operating modes and temperatures, self-diagnosis, adjustment information and history of the latest faults. Convenience of installation use Adjustment of operating parameters displaying information directly from ControllRemotClima Control. Clima Control/Ambient sensor and external probe as standard. New universal built-in unit in electro-galvanized sheet metal with complete arrangements for smoke outlets and hydraulic connections. Electrical protection degrees IPX5D and operation guaranteed to -15øC*. Prepared for the management and integration of thermal solar systems (standard solar probe). Standard predisposition for single-zone system management modules. Commissioning made easier: automatic de-aeration function and combustion regulation with direct access. Specific flush-mounting hydraulic kits also available with solar mixing valve. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less