RBM DIRT SEPARATOR INCLUDED Baxi Duo-Tec Compact E 24 kW low NOx condensing boiler complete with methane or LPG fume exhaust kit - News Technical features ErP energy efficiency class (heating and DHW): A Load profile: XL DHW nominal heat input kW 24.7 Heating nominal heat input kW 20.6 Seasonal space heating energy efficiency ŋs % 93 Emissions of nitrogen oxides NOx mg/kWh 15 Minimum operating temperature °C -5 Expansion vessel capacity l 7 Heating circuit water temperature adjustment °C 25-80 Domestic hot water production ∆T 25°C (1) l/min 13.8 DHW circuit minimum water flow rate l/min 2 Dimensions (hxlxp) mm 700x400x299 Degree of protection IPX5D NB: LPG OPERATION THROUGH ADJUSTMENT FROM THE AUTHORIZED SERVICE CENTER DUO-TEC COMPACT E range New design: change the aesthetics, not the performance. Luna Duo-tec E and Duo-tec Compact E: the already well-known Baxi boilers present themselves today with a new aesthetic, increasingly modern and attentive to new design trends, which allows them to be inserted in any living context. The control panel has also been completely renewed and is equipped with a new backlit LCD display that is even clearer and simpler to use thanks to dedicated and independent keys. The new boilers, even more beautiful and modern thanks to the restyling, however keep intact the characteristics that have always distinguished the Duo-tec range: Reliability. Robustness, durability and reliability in performance; Efficiency and savings. The reduction of the on/off cycles translates into considerable benefits in terms of energy savings and lower emissions; Completeness of range. Heating only models, with instantaneous DHW production, and also the compact version with the possibility of outdoor installation. The range has been further enriched with the new models equipped as standard with the modulating chronothermostat with integrated Wi-Fi Baxi Ma go The ideal boiler for new builds and replacements The Duo-tec E range of gas condensing boilers have been specifically designed in compliance with the requirements of the Ecodesign and Labeling Directives, to make them particularly suitable for both new builds and replacement old generator. The energy class, identified by a letter, expresses a range of efficiency values ​​within which the one expressed by the product in question resides. The label was created for the final consumer, so that, through real and comparable data, he can make informed choices by targeting high-efficiency products. Exchanger preheating function The boilers of the Duo-tec E range are equipped with the exchanger pre-heating function which guarantees the immediate production of domestic hot water at the set comfort temperature. In fact, the sanitary water passing through the plates of the preheated exchanger is already supplied at the desired temperature without waiting times. The function can be easily activated/deactivated by a specific boiler parameter Boiler info By pressing the dedicated key , it is possible to view numerous information regarding boiler operation such as: heating system water pressure (electronic pressure transducer present in the hydraulic unit); heating flow/return temperature; external temperature (with external probe installed); domestic hot water temperature. Efficiency and savings greater efficiency given by less switching on and off: with a high modulation ratio, the reduction of continuous switching on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions; adjustment of the thermal power produced to the power dissipated thus avoiding excessive overheating/cooling of the premises. Gas Adaptive Control It is an innovative system which, thanks to a new control electronics and a new electronic gas valve, guarantees automatic control of combustion to constantly maintain maximum efficiency values. Advantages: there are no manual interventions - reduced measuring, calibration or changing nozzles with this system, the boiler self-adapts to the quality of the gas and the length of the flue gas pipes, keeping efficiency constant the boiler also constantly regulates itself to maintain the maximum efficiency values, favoring a reduction in gas consumption and generating less pollution thanks to the continuous control of emissions Outdoor installation Duo-tec Compact E boilers can be installed outdoors in partially protected places thanks to the new top cover kit and bottom closure kit (available as accessories). In fact, the Duo-tec Compact E range is equipped AS STANDARD with an electronic antifreeze system which guarantees operation down to a temperature of -5 °C: the IPX5D protection also protects the electrical parts from jets of water which may come from all directions. New modern and elegant design for the whole range Wide modulation range 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control Digital control panel with large backlit LCD display New cover kit: possibility of outdoor installation in partially protected places (optional accessory) Rigid and flexible Ø50 mm exhaust pipe connection: solution for restoring flues - for mod. 24 kW total length 40 meters (intake+exhaust) Compact dimensions: 700x400x299 mm hydraulic system Electric three-way diverter valve Pre-mix burner in stainless steel Stainless steel water/fumes exchanger Increased DHW exchanger in stainless steel which allows the boiler to condense even in DHW operation Modulating fan with electronic speed variation Automatic by-pass High efficiency circulation pump with total modulation Pump anti-blocking system and three-way valve which intervenes every 24 hours Heating circuit safety valve at 3 bar Thermoregulation system Standard climate control (with external probe available as an option) Arrangement for connection to a zone system Control system Safety thermostat against overheating of the water/fumes exchanger Hydraulic pressure switch that blocks the gas in the event of a water shortage NTC safety probe against fume overheating Temperature control using NTC probes Total antifreeze device Electronic thermometer Heating circuit pressure gauge Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal heat input in heating max/min: Kw 23.5/5.5 Max/min nominal heat input in domestic hot water: Kw 23.5/5.5 Useful thermal power in heating: max/min: Kw 22.9/5.3 Efficiency at nominal heat input (60/80°C): 97.5% Efficiency at nominal heat input (30/50°C): 103.9% Efficiency at 30% at 30°C: 108.2% Max/min heating temperature (high temperatures): 82/35°C Max/min heating temperature (low temp.): 45/25°C Max/min DHW temperature: 60/36 °C Sanitary water production (DT=25°C): lt./min. 13.1 Specific flow rate (first 10' with DT=30°C): lt./min. 10.5 Total absorbed electric power W 87 Degrees of protection of the electrical system IP X5D Dimensions (HxWxD) mm 745 x 400 x 319 Power supply: CNG or LPG General characteristics Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. HS Premium Performance ★★★★ NOx class 5 LCD display. Continuous modulation high efficiency circulator. Modulation ratio 1:4. Arrangement for integration with system configuration through the new Buss Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation (with Sensys). Arrangement for solar system management. Aluminum alloy primary exchanger Sanitary plate heat exchanger. Self-diagnosis system by codes. Increased expansion tank lt.8. Cold water inlet and heating return filters. Protection against freezing, limescale and circulator blocking. Operation only with methane gas Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Gas Boiler Hermann Saunier Duval THEMATEK CONDENS 24 AS/1 kW Methane or LPG Complete with Smoke Kit - New PLEASE NOTE! THE BOILER WILL BE SUPPLIED WITH METHANE, THE TRANSFORMATION TO LPG WILL TAKE PLACE THROUGH THE SERVICE CENTER FOR FREE! Select the smoke kit in the drop-down menu! Technical features Model : Thematek Condens Power : 24 kW Gas : Methane or LPG Heating efficiency class: A Sanitary efficiency class: A Sanitary load profile XL Heating features Rated power Pmin/max - 80/60°C kW 6.0 - 18.3 Efficiency Pmax - 80/60°C - 50/30 °C % 97.2 - 106.4 Sanitary features Rated power min/max - 60°C kW 6.2 - 24.0 Specific flow rate (∆T = 30K) (EN13203) l/min 11.5 generals NOx class - 6 Electrical protection IPX - 5 Absorption - Stand-by / Pmax W 1.7 - 90 Dimensions (HxWxD) mm 626x400x270 Semiatek Condens The optimal solution for heating and domestic hot water preparation. Excellent value for money, both for new builds and replacements It can be retrofitted into existing heating and hot water supply systems Heat exchanger in stainless steel The Thematek Condens boiler is available in 24 and 28 kW methane power. The most important novelty concerns the renewed primary exchanger , the old one in Al-Si has been replaced by the one in stainless steel which, through a simple adjustment of the gas valve, also allows operation with propane. Innovation also from the point of view of combustion : complete premixing with new fan-push technology where the fan in the new position upstream of the burner guarantees the right ratio between air and gas by applying a proportional pressure value which guarantees the opening of the gas valve without waste. The project has been developed to offer the optimal solution in terms of price , performance and quality . Thematek Condens also presents a new design of the ultra-compact hydraulic block with a new position of the key components, while still maintaining a good level of efficiency, performance and adequate comfort both in heating and in the production of domestic hot water. Characteristics The new design of Thematek Condens offers an innovative touch screen interface of extreme simplicity with 6 keys, display with black background and 2 white digits with flashing on, the boiler status indication is defined by the flashing on of the icon selected. Thematek Condens is compatible with all Hermann Saunier Duval components and accessories already on the market. Thematek Condens can also be combined with the MiGo WiFi control unit. The wall-mounted boiler is ready to be managed remotely simply with a smartphone. Ease of installation SemiaTek Condens is very simple to install thanks to its small size - 62.6cm high, 40cm wide and 27cm deep - and low weight. Even the vertical hydraulic connections have been designed to facilitate and speed up installation. For these reasons, it is the ideal solution for replacing old systems. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

 ATTENTION Free methane/LPG/Propane air conversion during initial product verification and activation of the conventional guarantee, to be requested from the Authorised Assistance Centre Ferroli Bluehelix Theta 24C condensing boiler complete with flue gas exhaust kit Methane or LPG 0TPY2AWA Energy label specifications according to European ErP directive ERP class(Class G - A++) A / (Class G - A) A Max / min heating heat output kW 20.6 / 5, Max / min heating power (80/60°C) kW 20.0 / 4.9 Max / min heating power (50/30°C) kW 21.8 / 5.3 Max / min heat output sanitary (Hi) kW 25.0 / 5.0 Max / min thermal power for sanitary use kW 24.3 / 4.9 Efficiency Pmax / Pmin (80-60°C) (Hi) % 97.2 / 97.0 Efficiency Pmax / Pmin (50-30°C) (Hi) % 105.8 / 106.9 Yield 30% (Hi) % 108.8 Max / min operating pressure heating bar 3 / 0.8 Max / min sanitary operating pressure bar 9 / 0.3 Sanitary flow rate ∆t 25°C l/min 14 Sanitary flow rate ∆t 30°C l/min 11.7 Dimensions WxHxD mm 420x700x250; Empty weight kg 27 Bluehelix Theta WALL-MOUNTED CONDENSING BOILER INSTANTANEOUS SANITARY PRODUCTION > STRENGTHS: Boiler with single-circuit stainless steel primary exchanger without joints and/or welding, maintains high efficiency even on old systems. MC2: Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to changing gas network conditions (e.g. fluctuations or reduced pressures) MGR: Methane, LPG, Propane air Ready through a simple configuration the boiler is able to operate on methane, LPG and propane air without the use of additional conversion kits Instant production of domestic hot water with dedicated domestic hot water plate exchanger User interface with display and multifunction keys for adjusting and setting parameters By-pass as standard Hydraulic connections covered by the boiler casing Removable 3-part casing for quick and easy maintenance Refined design and compact size > BENEFITS OF THETA C: Solar system provision: provision for the production of domestic hot water combined with solar panel systems Sliding temperature operation via optional external probe Low consumption modulating heating circulator (ErP Ready - Class A) Digital flame control with three re-ignition attempts in the event of operation block due to lack of flame detection (methane model) FPS: Smoke Protection System. Using the optional smoke accessory (041106X0 - exhaust gas clapet valve kit) that can be installed outside the boiler, it is possible to easily connect to collective pressurised smoke systems (e.g. in renovations), in accordance with the UNI 7129 regulation. NB: the kit cannot be used in built-in installations. Installation location: also for outdoor use in a partially protected place up to -5°C as standard and up to -15°C with the aid of the optional antifreeze resistance kit Free methane/LPG/Propane air conversion upon initial product check and activation of the conventional warranty, to be requested from the Authorized Assistance Center Product Warranty All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase

Read more less

 ATTENZIONE  LA CALDAIA VIENE FORNITA A METANO. FUNZIONAMENTO A GPL TRAMITE REGOLAZIONE DA PARTE DEL CENTRO ASSISTENZA AUTORIZZATO. PER INFO, CONTATTARE PREVENTIVAMENTE L'ASSISTENZA BAXI  Caldaia Baxi Duo-Tec Compact E 24 kW a condensazione low NOx completa di kit scarico fumi Metano o Gpl - NovitàCaratteristiche Tecniche Classe di efficienza energetica ErP (risc e ACS): A  Profilo di carico: XL Portata termica nominale sanitario kW 24,7 Portata termica nominale riscaldamento kW 20,6 Efficienza energetica stagionale del riscaldamento d'ambiente ŋs % 93 Emissioni di ossidi di azoto NOx mg/kWh 15 Temperatura minima di funzionamento °C -5 Capacità vaso espansione l 7 Regolazione temperatura acqua circuito riscaldamento °C 25-80 Produzione acqua sanitaria ∆T 25°C (1) l/min 13,8 Portata minima acqua circuito sanitario l/min 2 Dimensioni (hxlxp) mm 700x400x299 Grado di protezione IPX5D Gamma DUO-TEC COMPACT E Nuovo design: cambia l’estetica, non le prestazioni. Luna Duo-tec E e Duo-tec Compact E: le già note caldaie Baxi si presentano oggi con una nuova estetica, sempre più moderna ed attenta alle nuove tendenze di design, che ne consente l’inserimento in qualsiasi contesto abitativo. Anche il pannello comandi è stato completamente rinnovato ed è dotato di un nuovo display LCD retroilluminato ancora più chiaro e semplice da usare grazie a tasti dedicati ed indipendenti. Le nuove caldaie, ancora più belle e moderne grazie al restyling, mantengono comunque intatte le caratteristiche che da sempre hanno contraddistinto la gamma Duo-tec: Affidabilità. Robustezza, durabilità e affidabilità nelle prestazioni; Efficienza e risparmio. La riduzione dei cicli di accensione/spegnimento si traduce in notevoli benefici in termini di risparmio energetico e minori emissioni; Completezza di gamma. Modelli solo riscaldamento, con produzione istantanea ACS, e anche la versione compatta con possibilità di installazione all’esterno. La gamma si è ulteriormente arricchita con i nuovi modelli dotati DI SERIE del cronotermostato modulante con wi-fi integrato Baxi MagoLa caldaia ideale per nuove costruzioni e per la sostituzione La gamma di caldaie a gas a condensazione Duo-tec E è stata specificatamente progettata rispettando i requisiti delle Direttive Ecodesign e Labelling, per renderla particolarmente adatta sia in caso di nuove costruzioni sia in sostituzione di un vecchio generatore. La classe energetica, identificata da una lettera, esprime un intervallo di valori di efficienza entro il quale risiede quello espresso dal prodotto in esame. L’etichetta nasce per il consumatore finale, in modo che, attraverso dati veri e comparabili, possa fare scelte consapevoli indirizzandosi su prodotti ad alta efficienza.Funzione preriscaldo scambiatoreLe caldaie della gamma Duo-tec E sono dotate della funzione di preriscaldo dello scambiatore che garantisce la produzione immediata di acqua calda sanitaria alla temperatura comfort impostata. Infatti, l’acqua sanitaria passando attraverso le piastre dello scambiatore preriscaldato, viene erogata già alla temperatura desiderata senza tempi di attesa. La funzione può essere facilmente attivata/disattivata da un apposito parametro della caldaiaInfo caldaiaPremendo il tasto dedicato , è possibile visualizzare numerose informazioni in merito al funzionamento della caldaia come ad esempio: pressione acqua impianto riscaldamento (trasduttore di pressione elettronico presente nel gruppo idraulico); temperatura di mandata/ritorno riscaldamento; temperatura esterna (con sonda esterna installata); temperatura acqua calda sanitaria.Efficienza e risparmio maggiore efficienza data da minori accensioni e spegnimenti: con un rapporto di modulazione elevato, la riduzione dei continui cicli di accensione/spegnimento comporta una significativa riduzione dei consumi (dell’8-10%) e una pari riduzione delle emissioni inquinanti; adeguamento della potenza termica prodotta alla potenza dissipata evitando quindi un eccessivo surriscaldamento/raffrescamento dei locali. Gas Adaptive ControlÈ un innovativo sistema che, grazie ad una nuova elettronica di controllo e ad una nuova valvola a gas elettronica, garantisce un controllo automatico della combustione per mantenere costantemente i valori di massima efficienza.Vantaggi: non ci sono interventi manuali - ridotte misurazioni, tarature o cambio ugelli con questo sistema, la caldaia si auto adatta alla qualità del gas e alla lunghezza dei tubi di scarico fumi mantenendo costante il rendimento la caldaia inoltre si autoregola costantemente per mantenere i valori di massima efficienza favorendo una riduzione dei consumi di gas e generando meno inquinamento grazie al continuo controllo delle emissioni Installazione all’esterno Le caldaie Duo-tec Compact E possono essere installate all’esterno in luoghi parzialmente protetti grazie al nuovo kit di copertura superiore e al kit di chiusura inferiore (disponibili come accessori). La gamma Duo-tec Compact E, infatti, è dotata DI SERIE di un sistema antigelo elettronico che garantisce il funzionamento fino alla temperatura di -5 °C: la protezione IPX5D, inoltre, tutela le parti elettriche da getti d’acqua che possono provenire da tutte le direzioni. Nuovo design moderno ed elegante per tutta la gamma Ampio campo di modulazione 1:7 maggiore efficienza e silenziosità GAC (gas adaptive control): controllo automatico della combustione Pannello comandi digitale con ampio display LCD retroilluminato Nuovo kit di copertura: possibilità di installazione all’esterno in luoghi parzialmente protetti (accessorio a richiesta) Allacciamento tubo di scarico Ø50 mm rigido e flessibile: soluzione per risanamento canne fumarie - per il mod. 24 kW lunghezza totale 40 metri (aspirazione+scarico) Dimensioni compatte: 700x400x299 mm Sistema idraulico Valvola deviatrice a tre vie elettrica Bruciatore a premiscelazione in acciaio inox Scambiatore acqua/fumi in acciaio inox Scambiatore sanitario maggiorato in acciaio inox che permette alla caldaia di condensare anche in funzionamento sanitario Ventilatore modulante a variazione elettronica di velocità By-pass automatico Pompa di circolazione ad alta efficienza a modulazione totale Sistema antibloccaggio pompa e valvola a tre vie che interviene ogni 24 ore Valvola di sicurezza circuito riscaldamento a 3 bar Sistema di termoregolazione Regolazione climatica di serie (con sonda esterna disponibile come optional) Predisposizione per il collegamento ad un impianto a zone Sistema di controllo Termostato di sicurezza contro le sovratemperature dello scambiatore acqua/fumi Pressostato idraulico che blocca il gas in caso di mancanza d’acqua Sonda NTC di sicurezza contro le sovratemperature dei fumi Controllo temperature mediante sonde NTC Dispositivo antigelo totale Termometro elettronico Manometro circuito riscaldamento Garanzia Prodotto :  Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.

Read more less

Baxi Boiler Open chamber Eco5 BLUE 24 Low NOx Methane Wall-mounted gas boiler with reduced polluting emissions (NOx and CO), instantaneous production of domestic hot water with natural draft and open chamber Installation type: B11BS Nominal heat input: 26.3kW Nominal heat output: 24 kW Reduced thermal power: 10.6 kW Efficiency at 30%: 89.6% Nominal efficiency: 90.3% Seasonal space heating energy efficiency class: C Seasonal energy efficiency class of the sanitary fixture: B Water heating - Load profile: XL NOx class 6 according to EN 15502 Domestic hot water production ∆T 25°C: 13.7 l/min Dimensions HxWxD 730x400x298; 27 kgs NOx class 6 CNG power supply Supplied accessories System filling tap; System drain cock; Installation template Conventional low NOx boilers for replacement in branched collective flues The ErP/EcoDesign legislation provides that, by way of derogation, manufacturers can continue to produce and market open-chamber, low NOx boilers, only for installations in domestic contexts, with the restriction of replacement in branched collective flues. Baxi's ranges of conventional B1-type natural draft boilers are precisely designed to meet all installation requirements in branched collective flues. ECO5 Blue NEW Conventional low NOx boilers for replacement in branched collective flues Low NOx emissions: class 6 according to EN 15502 Compact dimensions 730x400x298 mm Control panel with multifunction LCD display Arrangement for combination with the Baxi integrated solar system Product plus Control panel equipped with LCD display, programming and adjustment keys. Climatic regulation function (with optional external probe) integrated in the control panel Continuous electronic flame modulation Electronic ignition with flame ionization control Degree of protection: IPX5D Water cooled low NOx burner Primary water/gas exchanger made of copper pipes inserted in a lamellar coil protected by an anticorrosive alloy Secondary water/water exchanger in stainless steel Electric 3-way diverter valve Automatic by-pass on the heating circuit Pressure gauge on the heating circuit Expansion tank with 6 l capacity, preloaded at 0.5 bar ErP high efficiency circulation pump with built-in deaerator Turbine DHW flowmeter for detecting hot water withdrawal DHW operation with minimum water pressure of 0.15 bar and minimum flow rate of 2 l/min Inspectable filter on the sanitary water inlet Primary circuit safety valve at 3 bar Two heating water temperature adjustment ranges: 30÷45°C and 30÷85°C Sanitary water temperature adjustment range: 35÷60°C Minimum operating temperature: - 5°C Dimensions HxWxD: 73 x 40 x 30cm Control and security system Temperature control using NTC probes Pump post-circulation in the heating and DHW function Safety thermostat against overheating of the primary exchanger Hydraulic pressure switch which blocks the gas in case of water shortage Pump electronic control blocked Pump anti-blocking system and 3-way valve which intervenes every 24 hours Safety thermostat for checking the correct evacuation of fumes Total antifreeze device which intervenes with temperatures below 5°C Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. FOR CONVERTING TO LPG, CONTACT THE AUTHORIZED ASSISTANCE SERVICE IN ADVANCE Technical features Heating efficiency class A Sanitary efficiency class A XL load profile Nominal thermal power in DHW kW 25.2 DHW nominal heat input kW 3.1 / 24.5 Performance stars (Dir. 92/42CEE) ★★★★ NOx class 6 Nominal flow rate in heating (ΔT=30K) l/h 1033 Expansion vessel capacity l 8 Maximum operating overpressure bar 3 Domestic hot water production (ΔT = 30K) l/min 12.2 kW Domestic hot water comfort stars (prEN 13203) ★★ Power supply V/Hz 230/50 Dimensions H x W x L: 300x400x713; 36.0 kgs Power supply: METHANE Condensed 2300 W Condens 2300 W is designed to find space anywhere: its small size makes it easy to install in any domestic environment and makes it an ideal solution for modernization projects. First-class reliability Robustness and reliability of the compact wall-mounted condensing boiler are guaranteed thanks to the primary exchanger in Al-Si WB6 aluminum alloy Maximum seasonal yield The maximum seasonal efficiency obtainable from a condensing boiler (94%). Possibility of having a Class A+ boiler with the combination of a modulating thermoregulator with climatic function Extremely compact The extremely compact dimensions of this boiler make it the ideal replacement when you decide to change the old one Modulation ratio 1:10 The modulation ratio reaches up to 1:10, and is constant over time thanks to the modulation system without mechanical parts. This is to obtain greater gas savings and high comfort even with low domestic hot water requests EasyControl thermostat (optional) Wherever you are, you will feel at home, thanks to the wifi thermostat that can be managed with the app The revolutionary EasyControl thermostat from Bosch allows you to control it via app , wherever you are. All you need is an internet connection on your smartphone to control the temperature in all the rooms of your home directly from work. Our app guarantees continuous control over your system, giving you the possibility of deciding on a weekly schedule for both heating and domestic hot water. Remote management also helps you in some particular situations in your life: the children leave school early and are about to go home, but normally at that time there is no one at home and you have set a temperature of 19° degrees? No problem! While the children come home you can raise the temperature slightly directly from work thanks to the EasyControl thermostat app, so they will find the right warmth when they arrive. Furthermore, with the app you can also control your energy savings, monitoring your annual, monthly and weekly consumption. Finally, in the event of malfunctions in your heating system, you can request immediate assistance with a simple "touch" , directly from the app installed on your smartphone. The app is available for Android and iOS devices. Advantages Robust and reliable boiler thanks to the aluminum alloy primary exchanger Maximum seasonal efficiency of the boiler Modulation ratio up to 1:10 Extremely compact size boiler Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

 ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli condensing boiler Bluehelix Alpha 24C complete with methane or LPG fume exhaust kit cod. 0TPF2AWA Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating max / min heat input (Hs) kW 22.9 / 4.7 Max DHW heat input (Hi) kW 25 Max working pressure heating bar 3 Min. heating operating pressure bar 0.8 Heating expansion vessel capacity 8 litres Max DHW working pressure bar 9 Minimum DHW operating pressure bar 0.3 Sanitary flow rate ∆t 25°C l/min 14 Protection degree (IEC 60529) IP IPX4D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x250 Bluehelix Alpha .. More beautiful than "BEFORE" The new range of generators is equipped with the tested heat exchanger in stainless steel . Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX ALPHA is at the top of its category. TOP EFFICIENCY EVEN ON OLD SYSTEMS (REPLACEMENTS) mod. 24 C COMBINED (14 l/min at ∆t 25°C) The BLUEHELIX ALPHA thermal group exchanger (fig. A) compared with the more classic and widespread steel exchanger. This geometry allows the exchanger to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig. B tends to block up much faster in the part in contact with the flame due to the reduced passage area of ​​the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values BLUEHELIX ALPHA FROM THE INSIDE EXCHANGER High flow single circuit stainless steel exchanger, resistant to clogging and easy to clean STEEL FRAME Made with high precision automated processes EXPANSION TANK 8 liter expansion tank placed on the side ELECTRIC PANEL FAN Offset fan, to facilitate maintenance of the primary exchanger without disassembly DOMESTIC HOT WATER EXCHANGER In stainless steel, with copper brazing CIRCULATOR High efficiency, for heating and exchange with the DHW circuit SEALED CHAMBER Removable steel panel to protect the combustion chamber with the function of a sealed chamber ELECTRICAL PANEL Large removable electrical panel to protect against any water damage that may occur during normal maintenance. Easy access to electrical connectors. THE ENGINE The tube that makes up the BLUEHELIX ALPHA exchanger is made of stainless steel, a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits. THE BOILER CONTROL The control box of BLUEHELIX ALPHA consists of an easy to use interface with backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. MC2 The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). MGR Methane, LPG, Propane Ready Air The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). Thanks to the new electronics supplied, the gas change operation is extremely simple. The MC2 combustion control performs constant monitoring of the quality of the combustion and by simply modifying a parameter on the electronic card (operation to be carried out only by qualified personnel) it is possible to operate the boiler on Natural Gas or LPG or Propane Air. It is therefore not necessary to purchase additional accessory kits. CONNECT New wireless remote control available as an accessory for home comfort management also from a smartphone using the connect app (iOS and Android). Maximizes room comfort with delivery temperature modulation through the Room Climatic Compensation (CCA) and External Climatic Compensation (CCE) functions via the external temperature detectable directly from the internet (or from an optional external probe). It improves the average seasonal efficiency in space heating by +4%. EASY MAINTENANCE Problem-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the BLUEHELIX ALPHA thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: - The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - Easy access to the burner unit by removing 4 screws and the quick coupling (clip) of the fan. - The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. - The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. - Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front SUN EASY FUNCTION BLUEHELIX ALPHA has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. By means of a sensor located on the DHW circuit, it continuously controls the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. STOP AND GO FUNCTION With the use of sanitary taps with mixing, short or very short dispensing for quick rinses involves the start of the boiler ignition procedure which usually ends immediately. The continuation of these "false starts" can, in the long run, compromise the average life of the product. For this reason BLUEHELIX ALPHA provides an electronic parameter through which it is possible to delay burner ignition (Stop and Go) by activating it only in the face of actual withdrawals of domestic hot water. OUTDOOR INSTALLATION - ANTIFREEZE FUNCTION To make the most of the available space, the new BLUEHELIX ALPHA 24 - 28 C boiler can be installed recessed into the wall thanks to the special kit; for more critical installations, in completely uncovered places not protected from atmospheric agents, the "painted cabinet" kit is also available. In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. SANITARY ECO-COMFORT FUNCTION In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable. The efficiency and the load profiles according to the ErP directive are at the top of the category: mod. 24 C / A - XL. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

ATTENTION! THE BOILER IS BORN WITH METHANE. THEREFORE, THE TRANSFORMATION KIT WILL BE SUPPLIED AS STANDARD. FOR INFORMATION, CONTACT THE AUTHORIZED ASSISTANCE CENTER IN YOUR AREA IN ADVANCE Technical features Model : HS Premium Product code : 3301325 Power supply: Methane/LPG Energy efficiency Heating energy efficiency class: A Energy efficiency class for sanitary facilities: A Profile : XL Performance Nominal heat output in heating mode: 5.5 ~ 23.5 Kw Nominal heat output in sanitary mode: 5.5 ~ 23.5 Kw Useful thermal power in heating: 5.3 ~ 22.9 Kw Efficiency at nominal heat output (60/80°C): 97.5% Efficiency at nominal heat output (30/50°C): 103.9% Efficiency at 30% at 30°C: 108.2% High temperature heating temperature: 35° ~ 82°C Low temperature heating temperature: 25° ~ 45°C Sanitary temperature: 36° ~ 60°C Sanitary water production (DT=25°C): 13.1 lt/min Specific flow rate (first 10' with DT=30°C): 10.5 lt/min Total absorbed electrical power: 87 W Electrical system protection levels: IP X5D Dimensions and weight Dimensions (HxWxD): 745x400x319 mm Weight: 32.0 Kg Ariston HS Premium compact condensing boiler Along with heat, a traditional boiler also produces water in the form of steam, usually evacuated through exhaust fumes. Since normal boilers do not treat these fumes before releasing them into the environment, they therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process that, inside the boiler, transforms water from the state of steam back into the liquid state. Constant convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings on the bill, it takes less than three years to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real profit. Imagine what a bill reduced by up to 35% every year, for many years, means for your economies... Zero waste only benefits Today, Ariston combines energy savings with fiscal savings, offering a great opportunity to those who have chosen to replace their old boiler with a condensing one. The Financial Law provides, in fact, specific fiscal incentives for taxpayers. High efficiency circulator with continuous modulation. Modulation ratio 1:4. Ready for integration with system configuration through the new Buss Bridgenet® communication protocol Provision for multi-zone and multi-temperature thermoregulation (with Sensys). Provision of solar system management. Primary exchanger in aluminum alloy Sanitary plate exchanger. Self-diagnosis system using codes. Increased 8 litre expansion vessel. Cold water inlet and heating return filters. Anti-freeze, anti-scale and anti-blocking circulator protection. Product Warranty : All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase.

Read more less

The boiler is supplied with methane. Transformation of methane/LPG/Propaned air to be requested in advance from the Authorized Assistance Centre Technical features Model : Divatech D LNC 24 Power supply: LPG Energy efficiency Heating energy efficiency class: C Sanitary energy efficiency class: A ACS profile : XL Performance Heating nominal heat output : 7.3 ~ 22.8 kW Heat output : 8.3 ~ 25.0 kW Domestic useful thermal power: 22.8 kW Efficiency : 91.2% Maximum production of domestic hot water Δt 25°C : 13.8 l/min Maximum production of domestic hot water Δt 30°C : 10.9 l/min NOx : 6 Dimensions and weight Dimensions (HxWxD): 700x400x330 mm Empty weight: 27.0 kg Ferroli boiler DIVATECH D LN LOW NOX Wall mounted boiler with instantaneous domestic hot water production with double exchanger , open chamber, natural draft Strengths - Compact geometry primary heat exchanger entirely in copper - Instantaneous production of domestic hot water with dedicated plate domestic heat exchanger - Standard by-pass - Open chamber and natural draft boiler, with low NOx emission atmospheric burner , in AISI 304 stainless steel - High efficiency low consumption circulator (ErP - Class A) with anti-blocking system by activation for a few seconds every 24 hours of inactivity - Can be combined with the modulating remote timer control - Casing painted white by anaphoresis with epoxy powders - Simple and complete control panel, display user interface, with setting keys - Compact dimensions and low weight Advantages of Divatech D LN - Modulating heat input both in heating and in DHW production, managed by an electronic microprocessor card - ECO/COMFORT system for rapid production of domestic hot water - Adjustable post-circulation after the heating phase - Predisposition for solar systems : prearranged for the production of domestic hot water combined with solar panel systems - Certified operation also with propane air by means of a specific transformation to be requested from the Authorized Assistance Centre - Also works on LPG with the use of a special conversion kit to be requested from the Authorized Assistance Centre. Free transformation during product verification and activation of the guarantee only if the specific code running on LPG is not available Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Product name VAILLANT ecoTEC PURE CONDENSING VMW 246/7-2 COMPLETE WITH FUME EXHAUST KIT - NEW ErP Technical features Heating efficiency class A Sanitary efficiency class A XL load profile Nominal thermal power in sanitary kW 28.0 DHW nominal heat input kW 7.8 - 24.8 Performance stars (Dir. 92/42CEE) ★★★★ NOx class 5 Nominal flow rate in heating (ΔT=20K) l/h 1033 Expansion vessel capacity l 8 Maximum operating overpressure bar 3 Domestic hot water production (ΔT = 30K) l/min 13.5 Domestic hot water comfort stars (prEN 13203) ★★ Power supply V/Hz 230/50 Total electric power W 100 Dimensions H x W x L: 720-335-440; 30.8Kg Sound power dB(A): 49 Degree of protection IP X4 D Power supply: METHANE General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% ​​less CO2, using 20% ​​more renewable energy and consuming 20% ​​less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. NEW EcoTEC PURE The easiest way to switch to Vaillant condenser. Vaillant DNA is synonymous with quality. Always. ecoTEC pure represents the solution that Vaillant offers to anyone who wants to switch to a Vaillant condensing boiler without worries. ecoTEC pure is really simple to install. It is equipped with vertical hydraulic connections that make replacement jobs simple, both for those who are abandoning a traditional boiler (atmo-turboBLOCK), and for those who choose Vaillant for the first time. All in full compliance with the characteristics that identify Vaillant products: the boiler is in fact in energy class A both in heating and in the production of hot water. Even the new ecoTEC pure design immediately recalls the quality and reliability that characterize the company's DNA; the lines are clean for this new indoor condensing boiler with standard measurements: 70cm high, 44 wide and 33 deep. ecoTEC pure heats the water and the rooms to give the right comfort in a convenient way. It is available with a single model in the power of 24kW. Comfort, savings, safety Instant hot water even for small requests High sanitary comfort Condensation with Vaillant DNA The most convenient solution The vertical hydraulic connections allow for carefree replacement Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

THE BOILER IS BORN WITH METHANE. THEREFORE, YOU MUST REQUEST THE TRANSFORMATION KIT. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Technical features Model : ecoTEC Intro VMW 18/24 AS/1-1 Item code : 0010026087 Power supply: methane Performance Heating power : 6.0 ~ 18.3 kW Nominal heat input in DHW : 6.0 ~ 24.0 kW Energy efficiency class in heating: A Sanitary energy efficiency class: A Sanitary load profile : XL NOx class : 6 Efficiency at 30% : 107.8% Domestic hot water production (ΔT = 30K): 11.5 l/min Domestic hot water temperature adjustment: 35°C ~ 60°C Modulation : 1:4 Expansion vessel pre-charge pressure: 0.75 bar Minimum water pressure: 0.3 bar Total electric power: 90 W Expansion vessel capacity: 8 litres Dimensions and weight Dimensions (HxWxD): 626x400x270 mm Weight : 25.6Kg Warranty extension to 7 years ecoTEC Intro VMW wall-mounted condensing boiler The most compact and lightest, now also for outdoor use The new ecoTEC intro VMW condensing boilers (for heating and domestic hot water production) are available in 24 and 28 kW power ratings, increasing the range of product choices within the consolidated range of Vaillant condensing boilers. In fact, this product gives new users the opportunity to approach the world of condensing boilers offered by Vaillant, without incurring excessive costs for replacing the old boiler. ecoTEC intro maintains the focus on energy saving by mounting a high-efficiency modulating pump that minimizes annual electricity consumption , with a consequent positive impact on bills. Also with regard to gas savings, Vaillant offers the new combustion technology , called fan push, where it is the fan which, thanks to the different levels of pressure exerted on the gas valve, guarantees the right ratio between combustion air and gas. The ecoTEC intro case is simple and essential, the dimensions appear to be extremely small which however do not affect or reduce the quality and efficiency of the product, guaranteed by Vaillant. The front panel introduces an innovative , extremely simple touch screen interface with 6 keys, black background display and 2 white digits with intermittent switching on. An additional e-bus connector has been added to the bottom of the boiler which allows connection to Vaillant temperature control units and thermostats. These wall mounted boilers are very simple to install thanks to their dimensions (62.6cm high, 40cm wide and 27cm deep) and low weight (about 26kg): these features make them ideal whenever replacement is required. All the components that are present in the product comply with the ErP energy efficiency regulations, a guideline also embraced by Vaillant, as a brand sensitive to environmental issues. This is all that the new ecoTEC intro can offer, in addition to a competitive price which does not affect performance. First ignition free Vaillant guarantees, through the work of its technicians, the free first ignition service on all wall-mounted condensing boilers. ecoTEC wall mounted boiler intro Electricity consumption in standby less than 2W Innovative touch screen display Sanitary comfort even with low flow rates Low installation costs Small size Exchanger in stainless steel Pneumatic combustion system with complete pre-mixing Vertical hydraulic connections 1:4 modulation Instant DHW production 8 liter expansion tank Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less