ATTENTION THE BOILER IS SUPPLIED WITH METHANE. OPERATION WITH LPG THROUGH REGULATION BY THE AUTHORIZED ASSISTANCE CENTER. FOR INFORMATION, CONTACT YOUR LOCAL BAXI ASSISTANCE IN ADVANCE Baxi Luna Duo-tec E 33 Low NOx condensing boiler complete with flue gas exhaust kit for methane or LPG Technical Features Type: Wall-mounted condensing boiler; Model: Luna Duo-Tech Compact E; Energy efficiency class: A; Load Profile: XXL; Power supply: Methane/LPG Gas Adaptive Control; Warm-up Performance: Nominal heating heat output: 28.9 kW; Reduced heat output: 4.8 kW; Useful heat output at rated heat output and high temp. regime* P4: 28 kW; Useful thermal power at 30% nominal thermal power and low temp. mode** P1: 9.4 kW; Minimum operating temperature: -5°C; Expansion vessel capacity: 10 l; Heating circuit water temperature regulation: 25-80°C; Min/max pressure of heating circuit water: 0.5/3 bar; Performance in Healthcare: Nominal domestic hot water heat output: 34 kW; Nominal domestic hot water heat output: 33 kW; Domestic hot water temperature regulation: 35-60 °C; Domestic hot water production ?T 25°C: 18.9 l/min; Minimum water flow rate in the sanitary circuit: 2 l/min; Yields: Useful efficiency at rated thermal power and high temperature regime: 88.1 %; Useful efficiency at 30% rated thermal power and low temperature regime: 98.1 %; Useful efficiency (lvf) Pn - average temperature 70°C: 97.8 %; Useful efficiency (lvf) at 30% - return temperature 30°C: 108.9%; Intermediate useful efficiency (lvf) - average temperature 70°C: 98.2 %; Rated electrical power: 106 W; Auxiliary electricity consumption in stand-by mode: 0.003 kW; Nitrogen oxide emissions NOx: 15 mg/kWh; Sound power level, inside: 53 dB; Dimensions: (HxWxD): 763x450x345 mm; Weight: 39.5 kg; Luna Duo-tec General Features New modern and elegant design for the entire range Wide modulation range up to 1:7 (1:6 mod. 1.12) greater efficiency and silence GAC (gas adaptive control): automatic combustion control Digital control panel with large backlit LCD display Predisposition for combination with the Baxi integrated solar system Connection to Ø50 mm rigid and flexible exhaust pipe: solution for chimney restoration - for the 24 kW model Total length 40 meters (intake + exhaust) Hydraulic system Electric three-way diverter valve (also heating only models) Stainless steel premix burner Stainless steel water/fume exchanger Increased sanitary exchanger in stainless steel which allows the boiler to condense even in sanitary operation Electronically variable modulating fan of speed Automatic bypass High efficiency circulation pump with total modulation Anti-lock brake system pump and three-way valve which intervenes every 24 hours Heating circuit safety valve at 3 bar Thermoregulation system Climate control as standard (with external probe available as an option) Provision for connection to a zone system Control system safety thermostat against overtemperatures of the water/flue gas exchanger Hydraulic pressure switch that blocks the gas in case of lack of water NTC safety probe against flue gas overtemperatures Temperature control using NTC probes Total antifreeze device Electronic thermometer Digital pressure gauge heating circuit Product Warranty The warranty on this item is 24 months from the date of purchase.
€1.122,00
ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Technical features ErP energy efficiency class (heating and DHW): A Load profile: XL DHW nominal heat input kW 34 Heating nominal heat input kW 28.9 Sanitary nominal thermal power kW 33 Useful efficiency (pci) Pn - average temperature 70°C: 97.7% Heating expansion vessel capacity l 7.5 Storage tank expansion vessel capacity l 2 Sanitary water temperature adjustment °C 35-60 Boiler capacity 40 l Sanitary water production ∆T 25°C l/min 18.9 Domestic hot water production at discharge ∆T 30°C (1) l/30' 500 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions (hxlxp): 950x600x466 mm ; 67.5 kgs Power supply: CNG or LPG * Operation with LPG through adjustment by the Authorized Service Centre Cloud Duo-Tec+ Digital control panel The Duo-tec E range of boilers is equipped with a new digital control panel with an even more backlit LCD display, clearer and simpler to use thanks to dedicated and independent keys for regulating the temperature of the domestic hot water and of the heating. The display allows you to view all the information and set the operating parameters in an intuitive and immediate way. Efficiency and savings Wide modulation range: greater efficiency given by fewer starts and stops: with a high modulation ratio, the reduction of the continuous on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions adaptation of the thermal power produced to the power dissipated thus avoiding excessive overheating / cooling of the premises GAC Gas Adaptive Control It is an innovative system which, thanks to a new control electronics and a new electronic gas valve, guarantees automatic control of combustion to constantly maintain maximum efficiency values. Advantages: there are no manual interventions – reduced measurements, calibrations with this system, the boiler self-adapts to the quality of the gas (methane) and to the length of the flue gas pipes, keeping the efficiency constant the boiler also constantly regulates itself to maintain the maximum efficiency values, favoring a reduction in gas consumption and generating less pollution thanks to the continuous control of emissions. Fully modulating pump with de-aeration The circulation pump can operate at maximum speed, minimum speed or in "automatic" mode: in the latter case, the speed (min./max) will be selected so that the delivery/return ∆T in heating remains constant at 20 °C thus ensuring a significant reduction in pump consumption and, given the lower mechanical stresses (compared to a pump that always runs at maximum speed), also in maintenance costs. During the first ignition phase, we recommend activating the automatic de-aeration function. This function eliminates the presence of air in the heating circuit and therefore avoids any blockages of the boiler, overheating of the system, etc. Guidelines in case of replacement of a conventional boiler with a new condensing one There are two main problems that can be encountered: Flues and smoke exhaust duct Condensate drain To overcome the above, Baxi recommends: the use of a Ø50 mm exhaust pipe Baxi has in fact developed a system that allows easy ducting in existing flues (for 24kW models). For condensing boilers, the novelty is brought about by the low temperatures of the fumes which allow the use of specific plastic materials; however, in the presence of existing 316 stainless steel flues, installed correctly and with gaskets suitable for receiving damp fumes, there are no problems and they can easily be reconnected to the new boilers while it is absolutely not compliant with the use of aluminum flues or smoke pipes . In fact, aluminum is a metal that is not resistant to the acid condensates present in the fumes. (*) Each Ø50 mm diameter bend decreases the length of the drain by 4m the use of the condensate drain pump Baxi has designed this kit to collect the condensate produced by condensing boilers for domestic use: the pump allows the creation of condensate drainage systems in the absence of natural drainage near the boiler. The operation of condensing boilers determines the formation of condensate, due to the principle of condensation. This water therefore needs to be disposed of through special drains. If there is no adequate slope and therefore it is not possible to dispose of the condensate by gravity, it is necessary to install a pump that conveys it towards the drains. The pumps used are also equipped with special non-return valves to avoid bacterial contamination due to any stagnation and return of the waste water. The use of buildings avoiding the use of annoying pipes. Characteristics : Wide modulation range 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control Up to 500 l of hot water in 30 minutes (ΔT 30°C) 40 l stainless steel kettle Digital control panel with large backlit LCD display Compatibility with the Baxi Mago (optional accessory) for remote boiler control DHW expansion vessel available as STANDARD (for 33 kW mod.) and as an accessory (for 24 kW mod.) Connection to rigid and flexible Ø50 mm exhaust pipe: solution for restoring flues - mod. 24 kW total length 40 meters (intake+exhaust) STANDARD installation kit (gas cock / DHW inlet / telescopic fittings) hydraulic system Electric three-way diverter valve Pre-mix burner in stainless steel Flue water exchanger in stainless steel Stainless steel kettle Modulating fan with electronic speed variation Automatic by-pass High efficiency circulation pump with total modulation Pump anti-blocking system and three-way valve which intervenes every 24 hours Heating circuit safety valve at 3 bar 8 bar boiler safety valve Sanitary expansion vessel (2 litres) standard for mod. 33 GA VES Sanitary recirculation arrangement Thermoregulation system Standard climate control (with external probe available as an option) Arrangement for connection to a zone system Control system Safety thermostat against overheating of the water/fumes exchanger Hydraulic pressure switch which blocks the gas in case of water shortage Safety thermostat against fume overheating Temperature control using NTC probes Anti-legionella function Total antifreeze device Electronic thermometer Heating circuit digital pressure gauge Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.775,00
Kytek COMETA 33/33 kW condensing boiler with free flue gas kit Methane or LPG NOx 5 Technical features Model : COMET Maximum thermal power (Pn) (80/60 °C) 33.02 Maximum working pressure 3 bar Maximum domestic hot water potential 34.9 kw Maximum domestic hot water flow rate (?t: 30°C) 16.8 Power supply 230V +%10; -%15V AC-50Hz Dimensions (Height x Width x Depth) 725 x 420 x 288 mm NOx class 5 KYTEK COMET Large hot water production Modulation 1:10 Adaptive gas valve High insulation Inverter circulator Hydraulic group in brass Control Panel LCD display Water pressure switch Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€999,00
ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Technical features ErP energy efficiency class (heating and DHW): A Load profile: XL DHW nominal heat input kW 34 Heating nominal heat input kW 28.9 Sanitary nominal thermal power kW 33 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.6% Efficiency at 100% Pn (50-30°C): 105.4% Expansion/pre-charge vessel capacity l/bar 7.5/0.8 Sanitary water temperature adjustment °C 35-60 Boiler capacity 40 l Boiler expansion vessel capacity/pre-charge l/bar 2/3.5 Sanitary water production ∆T 25°C l/min 18.9 Sanitary water production at discharge ∆T 30°C l/30' 500 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions (hxlxp): 950x600x466 mm ; 67.5 kgs Power supply: CNG or LPG * Operation with LPG through adjustment by the Authorized Service Centre Cloud Platinum+ Wall mounted gas condensing boilers for heating and DHW production with storage Total modulation pump The Luna Platinum+ range is renewed with the introduction of a high efficiency electronic pump with permanent magnet motor. The new fully modulated pump allows, compared to using a pump Traditional modulating: Lower electricity consumption Better performance Greater durability Plant deaeration New electronic "system deaeration" function to facilitate the removal of air during initial ignition. Efficiency and savings The objective of a heat generator is to supply the energy necessary to the rooms to maintain conditions of maximum comfort inside them: this means supplying the rooms, through the system, with the same amount of heat that the building loses . In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. Wide modulation range Reduction of on-off cycles The graph shown above highlights the reduction in on/off cycles which distinguishes the new Platinum+ boilers with modulation up to 1:10 compared to a condensing boiler with lower modulation. The reduction of the on/offs determines an improvement in the efficiency of the boiler and consequently a considerable saving for the end user. Standard condensing boilers, on the other hand, with a limited modulation range work at a minimum power level above 6 kW; this allows it to avoid the on/off cycles for only 3% of the period of operation in heating, compromising the performance of the boiler and the life of the components. GAC: Gas Adaptive Control The electronics and the gas valve with stepper motor that the new Platinum+ boilers are equipped with guarantee automatic combustion control which is based on: on the flame signal GAC via the flame signal The system continuously measures the flame signal during boiler operation and adjusts the gas flow rate in order to keep the combustion quality constant and all this without requiring any additional component inside the combustion chamber. Installers and end users enjoy the following benefits of the GAC: The automatic combustion control favors a reduction in installation times as no manual adjustment of the gas valve or nozzle change is required: in fact, it is sufficient to manually modify some parameters of the electronic board for operation with LPG The boiler self-adapts to the quality of the gas and the length of the flue gas outlets: this means that there are no manual adjustments to make High modulation field 1:10: high efficiency and savings, since such a wide modulation field determines a greater adaptability of the boiler to the thermal dispersions of the building to obtain a higher efficiency and greater durability of the components. The reduction of the on/off cycles, in addition to the greater efficiency, guarantees less noise produced by the boiler Unlike traditional condensing boilers, the boiler always works adjusted to maximum efficiency values favoring a reduction in gas consumption and consequently a lower environmental impact thanks to the control of CO/CO emissions Power sets The term Power set identifies the heating power regulation process according to the project data. The thermal capacity of the boiler, through the Power set device, is adjusted according to the energy requirement: just act on the control panel to adjust some parameters Complete soundproofing C structure Silence is the relative or absolute absence of sound or noise. The noise level of the Luna Platinum+ boiler is comparable to a normal conversation Digital pressure gauge The electronic pressure transducer in the hydraulic unit allows you to check the pressure directly on the display. Double alarm level in the event of low pressure: a "warning" level in the event of low pressure in the boiler; a "block" level in the event of a lack of pressure Intubation solution For the rehabilitation of flues Baxi has developed a system that allows easy ducting into existing flues thanks to a Ø50 mm exhaust pipe (for 24kW models). Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€2.070,00
Caratteristiche tecniche Modello : Victrix Superior 35 Plus Codice prodotto : 3.033011 Alimentazione : Metano/Gpl Performance Portata termica nominale minima : 2,2 kW Portata termica nominale massima : 32,8 kW Potenza termica utile minima : 2,1 kW Potenza termica utile massima : 32,0 kW Rendimento termico utile al 100% Pn (80 / 60 °C) : 97,5% Rendimento termico utile al 100% Pn (40 / 30 °C) : 104,2% Portata di gas al bruciatore minima : 0,23 m3/h Portata di gas al bruciatore massima : 3,60 m3/h CO ponderato : 26,0 mg/kWh NOX ponderato : 30,0 mg/kWh Classe di efficienza energetica in riscaldamento : A Classe di NOx : 6 Prevalenza disponibile aspirazione/scarico minima : 2 Pa Prevalenza disponibile aspirazione/scarico massima : 281 Pa Capacità vaso d’espansione riscaldamento nominale : 10 litri Grado di protezione elettrica : IPX5D Dimensioni e peso Dimensioni (HxLxP) : 745x440x389 mm Peso a vuoto : 37,3 Kg Immergas Victrix Superior 35 Plus Caldaia murale a condensazione istantanea con Aqua Celeris e per solo riscaldamento Nuovo design, scheda elettronica hi-tech, performance idrauliche e comfort eccellente per le sostituzioni di caldaie obsolete. Le nuove caldaie a condensazione VICTRIX SUPERIOR hanno potenze da 26 e 35 kW nelle versioni istantanee e 35 kW per la versione solo riscaldamento ambiente. In particolare, le versioni istantanee garantiscono immediatezza nell’erogazione di acqua calda sanitaria grazie al sistema “Aqua Celeris”. Efficienza e attenzione all'ambiente Il campo di modulazione molto ampio garantisce l’alta efficienza, mentre circolatore a basso consumo e modulo a condensazione con serpentino di sezione ampia riducono i rischi di intasamento. La classe ecologica delle VICTRIX SUPERIOR è la 6: la migliore per le basse emissioni nocive. Facilità di installazione Tutti i modelli possono scaricare i fumi a parete e la clapet di serie permette l’abbinamento a sistemi di evacuazione dei fumi collettivi in pressione positiva. Le VICTRIX SUPERIOR si installano anche all’esterno in luoghi protetti. Gli attacchi idraulici sono identici ai precedenti modelli e il gruppo di allacciamento è di serie per favorire gli installatori nelle sostituzioni. Le VICTRIX SUPERIOR sono tutte equipaggiate di serie con filtro ciclonico magnetico. La caldaia VICTRIX SUPERIOR può raggiungere una classificazione energetica maggiore e (A+), se abbinata a un termoregolatore evoluto Immergas come lo SMARTECH PLUS o il CARV2 Massima flessibilità Le caldaie VICTRIX SUPERIOR hanno ottenuto la certificazione Hydrogen Ready. La nuova VICTRIX SUPERIOR può ora funzionare con unico codice a metano, GPL, aria propanata e miscela fino al 20% di idrogeno. Idrogeno La soluzione per ridurre l'emissione di CO2 e gas serra in ambiente Mentre il gas naturale emette anidride carbonica nell’atmosfera quando viene bruciato in una caldaia, l’idrogeno no. Dal momento che gran parte delle emissioni di anidride carbonica sono dovute all’industria del riscaldamento, questa nuova tecnologia può essere un’arma chiave nella lotta per raggiungere i livelli di emissioni zero di anidride carbonica. Per dare un’idea dei vantaggi ambientali, si pensi che l’introduzione della miscela di idrogeno al 20% in tutto il mondo permetterebbe di risparmiare circa 6 milioni di tonnellate di emissioni di anidride carbonica all’anno e la riduzione dei gas serra del 7%. Se le caldaie fossero completamente alimentate a idrogeno i risultati sarebbero straordinari. Formula Comfort 10 Si avvale del programma di manutenzione più completo della durata di 10 anni senza costi di attivazione, con la possibilità di estenderla fino a 15 anni. In collaborazione con il Centro Assistenza Autorizzato Immergas, si può attivare in occasione della verifica iniziale Modularità di installazione Predisposta per il funzionamento indipendente o in cascata, può essere installata in batteria fino a 3 apparecchi in abbinamento ai relativi kit optional (kit gestione caldaie in cascata; regolatore di cascata e zone, kit collettori con valvola di sicurezza 2,7 bar omologata INAIL) Le versioni PLUS hanno vaso d’espansione sanitario da 10 litri e sono omologate per esterno in luogo parzialmente protetto. Filtro cicloidale magnetico di serie I kit ciclonici magnetici sono filtri che uniscono il cosiddetto effetto “ciclonico” (separazione delle impurità tramite movimento circolare dell’acqua) all’effetto magnetico ottenuto tramite una barra contenente magneti permanenti che si trova in posizione centrale, e che trattiene le particelle ferrose che si trovano in sospensione nell’acqua. VICTRIX SUPERIOR ha di serie , da montare in opera , il filtro ciclonico magnetico. Si posiziona sul ritorno dell’acqua impianto ed è completo di 2 rubinetti di intercettazione che permettono di sfilare il magnete operando lo svuotamento dell’acqua contenuta nel filtro stesso senza svuotare l’intero impianto. Scambiatore primario in acciaio inox Lo scambiatore primario che equipaggia le VICTRIX SUPERIOR è realizzato con serpentino di scambio mono-tubo in acciaio Inox. L’assenza di collettori e circuiti in parallelo, garantisce la massima affidabilità nel tempo: non sono presenti saldature. La singola spirale in acciaio Inox senza strozzature permette di avere un circuito idraulico perfettamente bilanciato, riducendo notevolmente le perdite di carico. La sezione interna, ampia e costante, consente di limitare depositi, riducendo i rischi di intasamento nel caso di impurità presenti nell’acqua, ad esempio nel caso di sostituzione di caldaie su impianti datati. Per questa sua peculiarità, le VICTRIX SUPERIOR sono ideali nella sostituzione. Nuovo ed elegante design , elettronica Hi-TECh Equipaggiata con portello di chiusura cruscotto e ampio display sempre in vista, tasti touch retroilluminati e comode manopole per effettuare le regolazioni. Il display risulta ben illuminato e leggibile e i tasti touch sono dotati di un ottimo feedback tattile, in linea con l’elevato livello qualitativo del prodotto. Oltre all’illuminazione dei tasti, la scheda è dotata di segnalatore acustico in grado di evidenziare in modo sonoro i comandi attuati dall’utente sui pulsanti. L’elettronica hi-tech mette a disposizione numerose nuove funzioni come ad esempio la possibilità di gestire direttamente dal cruscotto di caldaia 3 zone o la comodità di impostare 4 fasce orarie comfort e 4 calendari, per la programmazione delle zone impianto e del sanitario. L'evoluzione nella termoregolazione Impianti con più zone Equipaggiata di serie con elettronica di ultima generazione, è possibile la gestione di 3 zone con l’ausilio di sonde ambiente wireless e concentratore , entrambi optional. L’impostazione delle temperature ambiente e delle fasce orarie di funzionamento avviene direttamente dal cruscotto della caldaia o a distanza tramite app (da telefono, tablet o pc) con l’ausilio del kit optional interfaccia DOMINUS. È predisposta per abbinamento con gateway Theben (non fornito da Immergas) per la gestione domotica mediante protocollo KONNEX. In ville unifamiliari particolarmente estese la gestione dell’impianto può essere affidata al kit disgiuntore impianto DIM ErP. Il carter inferiore della caldaia è predisposto per il fissaggio sia del concentratore sonde ambiente che della scheda di interfaccia DOMINUS, rendendo agevole all’installatore le operazioni di montaggio dei kit. Impianti monozona Queste applicazioni possono essere gestite in modo semplice attraverso lo SMARTECH PLUS (con relativa app per il controllo a distanza), oppure con il CARV2 (entrambi optional). Garanzia prodotto : Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è di 24 mesi dalla data dell'acquisto.
€2.296,00
Technical features ErP energy efficiency class (heating and DHW): A Load profile: XXL DHW nominal heat input kW 34 Heating nominal heat input kW 28.9 Sanitary nominal thermal power kW 33 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.6% Efficiency at 100% Pn (50-30°C): 105.4% Expansion/pre-charge vessel capacity l/bar 8/0.8 Sanitary water temperature adjustment °C 35-60 Sanitary water production ∆T 25°C l/min 18.9 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions (h x w x d): 760 x 450 x 345 mm ; 39.5 kgs Power supply: CNG or LPG *Operation on LPG through adjustment by the Authorized Assistance Centre Moon Platinum+ Wall mounted condensing gas boilers for heating only and instant DHW production. Ecodesign and Labeling - From Baxi research comes a complete range of condensing boilers with high technological content designed in compliance with the requirements of the Ecodesign and Labeling directives, to ensure maximum domestic comfort. Latest generation electronics, high efficiency and compact design make the Platinum+ range the ideal solution for both new installations and replacement. THINK raises system efficiency - The Platinum+ range of boilers is designed with the Think technology platform - intelligence within, an exclusive system that makes them "think" intelligently! With this authentic "the brain inside the box", the Baxi proposal confirms itself as the intelligent choice for making the boiler communicate in a simple and flexible way with all the main heating technologies, creating increasingly complex and energy-efficient design solutions. Furthermore, the Think platform makes the boiler very easy to use, in line with the Baxi design tradition aimed at totally user-friendly management of the appliance. Even the least experienced user can thus interact with the new control panel and program his own domestic comfort with the utmost simplicity. With the range of condensing boilers with the Think platform, Baxi comfort is easy and smart. The combination of the Platinum+ boiler for heating and DHW production and THINK controls for intelligent management of the system allows efficiency to be raised to class A+. The Platinum+ range is equipped AS STANDARD with a removable control panel for remote management (wired or wireless) of the boiler, equipped with a large multifunction text display with modulating thermoregulation control unit functions. GAC - The innovative automatic combustion control system GAC (Gas Adaptive Control) guarantees a wide modulation range up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adapt the thermal power produced to the effective power dissipated by the building avoiding excessive overheating/cooling of the building. Efficiency and savings - The objective of a heat generator is to supply the energy necessary to the rooms to maintain maximum comfort conditions inside: this means supplying the rooms, through the system, with the same amount of heat the building disperses. In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. Total modulation pump The Luna Platinum+ range is renewed with the introduction of a high efficiency electronic pump with permanent magnet motor. The new fully modulated pump allows, compared to using a pump traditional modulating: Lower electricity consumption Better performance Greater durability Plant deaeration New electronic "system deaeration" function to facilitate the removal of air during initial ignition. Efficiency and savings The objective of a heat generator is to supply the energy necessary to the rooms to maintain conditions of maximum comfort inside them: this means supplying the rooms, through the system, with the same amount of heat that the building loses . In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. The graph shown above highlights the reduction in on/off cycles which distinguishes the new Platinum+ boilers with modulation up to 1:10 compared to a condensing boiler with lower modulation. The reduction of the on/offs determines an improvement in the efficiency of the boiler and consequently a considerable saving for the end user. Standard condensing boilers, on the other hand, with a limited modulation range work at a minimum power level above 6 kW; this allows it to avoid the on/off cycles for only 3% of the period of operation in heating, compromising the performance of the boiler and the life of the components. GAC : Gas Adaptive Control The electronics and the gas valve with stepper motor that the new Platinum+ boilers are equipped with guarantee automatic combustion control which is based on: on the flame signal The system continuously measures the flame signal during boiler operation and adjusts the gas flow rate so as to maintain the quality of combustion constant and all this without requiring any additional component inside the combustion chamber. Installers and end users enjoy the following benefits of the GAC: The automatic combustion control favors a reduction in installation times as no manual adjustment of the gas valve or nozzle change is required: in fact, it is sufficient to manually modify some parameters of the electronic board for operation with LPG The boiler self-adapts to the quality of the gas and the length of the flue gas outlets: this means that there are no manual adjustments to make High modulation field 1:10: high efficiency and savings, since such a wide modulation field determines a greater adaptability of the boiler to the thermal dispersions of the building to obtain a higher efficiency and greater durability of the components. The reduction of the on/off cycles, in addition to the greater efficiency, guarantees less noise produced by the boiler Unlike traditional condensing boilers, the boiler always works adjusted to maximum efficiency values favoring a reduction in gas consumption and consequently a lower environmental impact thanks to the control of CO/CO2 emissions Power sets The term Power set identifies the heating power regulation process according to the project data. The thermal capacity of the boiler, through the Power set device, is adjusted according to the energy requirement: just act on the control panel to adjust some parameters. Complete soundproofing C structure Silence is the relative or absolute absence of sound or noise. The noise level of the Luna Platinum+ boiler is comparable to a normal conversation. Digital pressure gauge The electronic pressure transducer in the hydraulic unit allows you to check the pressure directly on the display. Double alarm level in the event of low pressure: a "warning" level in the event of low pressure in the boiler; a "block" level in the event of a lack of pressure. Intubation solution For the rehabilitation of flues Baxi has developed a system that allows easy ducting in existing flues thanks to a Ø50 mm exhaust pipe (for 24kW models) Characteristics: wide modulation range 1:10 greater efficiency and silence GAC (gas adaptive control): automatic combustion control high-efficiency circulation pump with total modulation removable and backlit control panel in wireless and wired version for wall installation, with large text display, adjustment knob and menu selection keys power set: heating power adjustment according to project data integrated electronic management for coupling to a solar system Ø50 mm exhaust pipe: solution for restoring flues - mod. 24 kW STANDARD installation kit (gas cock / DHW inlet / telescopic fittings) antifreeze function and IPX5D degree of protection Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.341,00
Overview BAXI DUO-TEC MAX+ 33 GA CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP 2015 Technical specifications ErP energy efficiency class (heating and DHW): A Load profile: XL Sanitary nominal heat inputkW 34ÿ Heating nominal heat input kW 28.9 Sanitary nominal thermal powerkW 33 Energy efficiency(92/42/CEE)ÿ**** Efficiency 100% Pn (80-60øC): 97.8% Efficiency 100% Pn (50-30øC): 105.8% Expansion/pre-charge capacity l/bar 8/0.8 Sanitary water temperature adjustmentøC 35-60ÿ Sanitary water production T 25øC l/min 18.9 Degrees of protection: IPX5Dÿ NOx class (EN 483) 5 Dimensions (hxwxd): 760 x 450 x 345ÿmmÿ; 39.5 kgs Power supply: LPG Features list Duo-Tec Max+ The new range of gas condensing boilersÿDuo-tec+ÿ has been specifically designed in compliance with the requirements of the Ecodesign and Labeling Directives, to make it particularly suitable both for new buildings and for replacing an old generator. In fact, in addition to the already known advantages of condensing technology such as efficiency, energy saving and reduced polluting emissions, the new Duo-tec+ condensing boilers are characterized by: Complete range of models: heating only, with instantaneous DHW production, with integrated micro-storage tank, with integrated 40 liter storage tank. The range also includes the compact version (Compact+), the first Baxi condensing boiler in just 70 cm in height and 30 cm in depth. Digital control panel with backlit LCD display Wide range of 1:7 modulationÿreduction of on/off cycles translates into significant benefits in terms of energy savings and lower emissions digital control panel The Duo-tec+ range of boilers is equipped with a digital control panel with backlit LCD display, simple to use thanks to dedicated and independent keys for regulating the temperature of the domestic hot water and of the heating. The display allows you to view all the information and set the operating parameters in immediate change. Gas Adaptive Control The innovative automatic combustion control system GAC (Gas Adaptive Control) guarantees a wide modulation range of up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adapt the thermal power produced to the effective power dissipated by the building, thus avoiding excessive overheating/cooling of the building. Full modulation pumpÿ Can the circulation pump operate at maximum speed, at minimum speed in mode or automatic?: in the latter case, the speed (min./max) will be selected so that the heating delivery/return T remains constant at 20°C thus guaranteeing a significant reduction of pump consumption and, given the lower mechanical stresses (compared to a pump that always runs at maximum speed), also of maintenance costs Characteristics: *** of sanitary comfort(EN 13203) wide modulation ranges fine 1:7 greater efficiency and silence GAC (gas adaptive control): automatic control of combustion mini accumulator integrated in the expansion vessel (Baxi patent) digital control panel with large backlit LCD display high-efficiency circulation pump with total modulation antifreeze function IPX5D protection degree To be placed on the EU market, a productÿmustÿhave the brand,ÿthat is, comply with all the European Directives applicable to it.ÿ The ÿEcodesign and Labellingÿ Directives (eco-design and energy labelling) were created to help the EU achieve the objectives of the EU Plan 20-20-20, with a particular focus on reducing CO2 emissions by 20%, increasing energy efficiency 20% and the increase in the use of renewable energy by 20%, by 2020. For this reason, all heat generators for space heating, appliances for the production of DHW and systems of several of these appliances combined in combination will have to comply with the requirements for eco-design and be labelled, according to the quantity established by the implementing regulations, in order to be placed on the marketby producers. From 26 September 2015, the directives will affect all the products described above with a Pn 400 kW for eco-design and with a Pn 70 kW for labeling, destined for the markets of all countries of the European Economic Area. How is placing on the market Placing on the market is carried out by the manufacturer (by the importer from outside the EU) when the product remains available for the first time on the EU market.ÿThis happens when ownership changes to a distributor (invoice). ÿHow the placing on the market takes place Placing on the market is carried out by the manufacturer (by the importer from outside the EU) when the product remains available for the first time on the EU market.ÿThis happens when ownership changes to a distributor (invoice). ÿWhat products can be sold All products with CE marks placed on the market before 01/08 and 26/09 2015 are considered compliant and therefore salable until exhaustion. All products that will be placed on the market (sold) by the manufacturer/importer after these dates must comply with the new standards . What is a product according to ErP (Ecodesign) A device designed to operate at maximum efficiency with minimum environmental impact. To comply with this directive, the product must have Pnÿ 400 kW and as regards the hot water tanks, a volumeÿ 2000 litres. Manufacturers are obliged toÿplace on the marketÿonly ErP-compliant products with these deadlines: sinceÿAugust 1, 2015ÿonly products equipped with high efficiency pump fromÿ26 September 2015ÿonly products that meet the minimum ErP efficiency requirementsÿ Ecodesign defines the requirements that products must meet in order to be placed on the market, based on: Seasonal efficiencyÿfor heating and efficiency for DHW production based on the declared load profileÿ Emissionsÿ(NOx values)ÿ Maximum allowable noiseÿof hydronic heat pump outdoor unitsÿ What is a Combi product according to ErP An appliance (single with boiler) for heating and DHW production, already equipped with labeling with energy class information relating to a DHW loader profile. What is the energy label The labeling directive (2010/30/EU) requires the labeling of products according to a decreasing energy scale that goes from A + + + to GE An energy label is also provided for the installed system, depending on the components used (for example a boiler, DHW tank and room temperature controls). The label was created for the final consumer, providing real and comparable data, to make informed choices and targeting high-efficiency products. Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.
€1.346,00
Technical features ErP energy efficiency class (heating and DHW): A Load profile: XXL DHW nominal heat input kW 34 Heating nominal heat input kW 28.9 Sanitary nominal thermal power kW 33 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.7% Efficiency at 100% Pn (50-30°C): 105.5% Expansion/pre-charge vessel capacity l/bar 8/0.8 Sanitary water temperature adjustment °C 35-60 Sanitary water production ∆T 25°C l/min 18.9 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions ( HxWxD ): 763 x 450 x 345 mm Weight : 43.5Kg Power supply: METHANE Wall-hung gas condensing boilers ideal for replacing old systems with cast iron/lamellar steel radiators The new condensing range Luna Alux is divided into two models, 24 and 33 kW for heating and instant domestic hot water production. Luna Alux was designed in compliance with the requirements of the Ecodesign and Labeling Directives. The labeling directive (2010/30/EU) requires the labeling of products according to a decreasing energy scale that goes from A++ to G starting from 09/26/2015 and from A+++ to D from 09/26/2019. The label was created to allow the final consumer, by providing true and comparable data, to make informed choices by targeting high-efficiency products. Exclusive design aluminum heat exchanger Luna Alux is the new Baxi condensing boiler equipped with a corrosion-resistant aluminum-silicon alloy exchanger which makes this boiler particularly solid. The exchanger, designed and produced on an exclusive Baxi design, has been studied with large water passage sections to make the boiler particularly suitable for replacement in old heating systems with cast iron or lamellar steel radiators In these types of systems, the replacement of the existing boiler with a new LUNA ALUX: Significantly lowers the risk of clogging due to impurities in the system water Makes operation particularly quiet The high water content inside the exchanger determines: Less temperature fluctuations Increased overheat protection More effective DHW pre-heating Furthermore, the exchanger can be inspected and this facilitates periodic maintenance Digital control panel The Luna Alux range of boilers is equipped with a digital control panel with backlit LCD display, easy to use thanks to dedicated and independent keys to adjust the temperature of the domestic hot water and the heating. The display allows you to view all the information and set the operating parameters in a clear and immediate way. Efficiency and savings Wide modulation range: Greater efficiency given by less switching on and off: with a high modulation ratio, the reduction of continuous switching on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions adjustment of the thermal power produced to the power dissipated thus avoiding excessive overheating/cooling of the premises Hydraulic group in brass Baxi has chosen to maintain quality in its components. The brass hydraulic group, in fact, is a guarantee of: Robustness Greater durability Recyclability Wide modulation range 1:7 greater efficiency given by fewer starts and stops: with a high modulation ratio, the reduction of continuous on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions • power adjustment produced at the dissipated power thus avoiding excessive overheating/cooling of rooms A Gas Adaptive Control The innovative GAC (Gas Adaptive Control) automatic combustion control system guarantees a wide modulation range up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adjust the thermal power produced to the actual power dissipated from the building avoiding excessive heating/cooling of the building. High efficiency total modulation pump The Alux range is equipped with a high-efficiency, fully modulated circulation pump. The pump is equipped with a permanent magnet motor with a variable rotation speed controlled by the boiler board. The high efficiency total modulation pump allows: Lower electricity consumption Better performance Greater durability Characteristics: Wide modulation range 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control to constantly maintain the maximum efficiency values (operation on methane only) High efficiency circulation pump with total modulation Aluminum-silicon alloy exchanger with large water passage sections Hydraulic group in brass 10 liter expansion vessel (mod. 33) Easy maintenance thanks to front access to components Digital control panel with large backlit LCD display Arrangement for combination with the Baxi integrated solar system Electronic system deaeration function to facilitate air removal during initial ignition Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€1.410,00
ATTENTION ! For the transformation of methane/LPG/free propane air to be requested from the Authorized Assistance Centre Technical features Model : Enerwa 33 Gas : Methane / LPG Hydraulic unit material : Brass Class : NOx 5 Gas circuit Natural gas consumption: 0.434 ~ 3.40 m 3 /h LPG gas consumption: 0.168 ~ 1.30 m 3 /h Efficiency : 106.9 ~ 107.2% Radiator circuit Maximum thermal load : 33.7 kW Maximum thermal power (80/60° C): 33.02 kW Maximum thermal power (50/30° C): 35.5 kW Thermal regulation range : 25° ~ 80° C Maximum working pressure: 3 bar Domestic hot water circuit Maximum domestic hot water capacity: 34.9 kW Maximum domestic hot water flow rate (∆t: 30°C): 16.8 l/min Maximum domestic hot water flow rate (∆t: 25°C): 20.1 l/min DHW temperature adjustment : 35° ~ 60 °C Electrical circuit Power supply (V,Hz, Ø) : 220~240/50/1 Power Consumption: 60~115W Dimensions and weight Dimensions (HxWxD): 725x420x288 mm Weight : 35Kg Warmhaus Enerwa and EnerwaPlus boilers The New Era of Boilers Combined wall boiler Enerwa and Enerwa Plus thanks to their small dimensions of only 288mm deep and their modern design are ideal for installation on balconies or inside kitchens Reliable and efficient The new self-adaptive system of the electronic gas valve precisely adjusts the combustion ratio between air and gas. No pre-heating system, the boiler keeps the water hot for the entire time of use. Effective circulation Circulator with frequency converter, it is a high efficiency pump with a head of 7 mwc Intelligent LCD display Large LCD display, the display shows the heating temperature, DHW and internal pressure System expansion 8 liter expansion tank. The new expansion vessel is capable of supplying 130/140lt of water to the system Adaptive Gas Control With its signal it can provide simultaneous control of ionization and gas valve Highly economical It is a question of having an electrical consumption reduced to a maximum of 82W Hot water and continuous flow Asymmetrical exchanger system, provides a high flow input with its large water passages Pressure sensor to optimize performance Possibility to set the altitude of the boilers to optimize efficiency Silent operation Thanks to the 10mm internal lining, you work very silently and with excellent thermal insulation Processor specifications SMART WARMHAUS High efficiency High efficiency radial heat exchanger with low risk of clogging and leak proof. Panel features Selection buttons for mode, reset, heating and DHW Intuitive buttons for selecting the heating and DHW temperature Temperatures on LCD screen Flame modulation indicator Digital pressure gauge Self-diagnostic codes and system identification Different working parameters for boilers Differences between Enerwa and EnerwaPlus Energy Aesthetics Control Panel: 2 Knobs, 2 Buttons LCD display : 30 mm x 44 mm , Blue LCD screen , backlit Water pressure switch: EO2 low pressure alarm. Water pressure visible on the pressure gauge Self-regulating circulator EnerwaPlus Aesthetics Control Panel : 6 Buttons LCD display : 40 mm x 75 mm , Orange LCD screen , backlit Water pressure switch : Water pressure sensor. EO2 low pressure alarm. E03 high pressure alarm. Water pressure visible on pressure gauge and LCD screen Circulator with PWM (Pulse-Width-modulation) control Pulse-width modulation Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.257,00
ATTENZIONE ! Per la trasformazione metano/GPL/Aria propanata gratuita da richiedere al Centro Assistenza Autorizzato Caratteristiche Tecniche Modello : Enerwa Plus 33 Gas : Metano / Gpl Materiale gruppo idraulico : Ottone Classe : NOx 5 Circuito gas Consumo di gas Metano : 0,434 ~ 3,40 m3/h Consumo di gas Gpl : 0,168 ~ 1,30 m3/h Efficienza : 106,9 ~ 107,2 % Circuito radiatori Carico termico massimo : 33,7 kW Potenza termica massima (80/60° C) : 33,02 kW Potenza termica massima (50/30° C) : 35,5 kW Gamma di regolazione termica : 25° ~ 80° C Pressione massima di esercizio : 3 bar Circuito acqua calda sanitaria Potenzialità massima acqua calda sanitaria : 34,9 kW Portata massima acqua calda sanitaria (∆t: 30°C) : 16,8 l/min Portata massima acqua calda sanitaria (∆t: 25°C) : 20,1 l/min Regolazione temperatura A.C.S. : 35° ~ 60° C Circuito elettrico Alimentazione (V,Hz, Ø) : 220~240/50/1 Consumo energetico : 60 ~ 115 W Dimensioni e peso Dimensioni (AxLxP) : 725x420x288 mm Peso : 35 Kg Caldaie Warmhaus Enerwa e EnerwaPlus La Nuova Era delle Caldaie Caldaia murale combinata Enerwa ed Enerwa Plus grazie alle sue contenute dimensioni di soli 288mm di profondità ed il loro design moderno sono ideali per l’installazione su balconi o all’interno delle cucine Affidabile ed efficiente Il nuovo sistema auto adattivo della valvola gas elettronica regola in maniera precisa il rapporto di combustione tra aria e gas. Nessun sistema di pre-riscaldamento , la caldaia mantiene l’acqua calda per tutto il tempo di utilizzo. Efficace circolazione Circolatore con convertitore di frequenza , si tratta di una pompa ad alta efficienza con prevalenza di 7 m.c.a. Display LCD intelligente Ampio display LCD , il display mostra la temperatura di riscaldamento, A.C.S. e la pressione interna Espansione impianto Vaso d'espansione da 8 litri. Il nuovo vaso d’espansione è in gradi di fornire 130/140lt d’acqua al sistema Controllo gas adattivo Con il suo segnale può fornire il controllo simultaneo di ionizzazione e valvola gas Altamente economica Si tratta di avere un consumo elettrico ridotto al massimo 82W Acqua calda e flusso continuo Sistema di scambiatore asimmetrico , fornisce un elevato apporto di flusso con i suoi ampi passaggi d’acqua Sensore di pressione per ottimizzare le prestazioni Possibilità di impostare l’altitudine delle caldaie per ottimizzare l’efficienza Silenziosità Grazie al rivestimento interno di 10mm si lavora con la massima silenziosità e con un ottimo isolamento termico Specifiche del processore SMART WARMHAUS Alta efficienza Scambiatore alta efficienza radiale a basso rischio di instasamento ed a prova di perdite. Caratteristiche pannello Pulsanti di selezione per modalità, reset, riscaldamento ed A.C.S. Pulsanti intuitivi per la selezione della temperatura di riscaldamento ed A.C.S. Temperature su schermo LCD Indicatore modulazione di fiamma Manometro digitale di pressione Auto-diagnostica codici ed identificazione di sistema Differenti parametri di lavoro per le caldaie Differenze tra Enerwa e EnerwaPlus Enerwa Estetica Pannello di controllo : 2 Manopole , 2 Pulsanti Display LCD : 30 mm x 44 mm , Schermo LCD blu , retroilluminato Pressostato acqua : EO2 allarme bassa pressione. Pressione dell’acqua visibile sul manometro Circolatore autoregolante EnerwaPlus Estetica Pannello di controllo : 6 Pulsanti Display LCD : 40 mm x 75 mm , Schermo LCD arancio , retroilluminato Pressostato acqua : Sensore pressione acqua. EO2 allarme bassa pressione. E03 allarme alta pressione. Pressione dell’acqua visibile su manometro e su schermo LCD Circolatore con controllo PWM (Pulse-Width-modulation) Modulazione a larghezza di impulso Garanzia Prodotto : Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.
€1.285,00
BAXI LUNA DUO-TEC+ 33 GA LPG CONDENSING GAS BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Technical features Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XXL Class A Characteristics of heating/DHW operation: Sanitary nominal heat input: 34 kW Nominal heat input Heating: 28.9 kW Reduced thermal input: 4.8 kW Sanitary thermal power: 33 kW Nominal thermal power Pnominal: 28 kW Useful efficiency at 30% thermal power. name and low temp. regime: 98.1% Useful efficiency (pci) at 30% - return temperature 30°C: 108.9% Minimum operating temperature: -5°C Expansion vessel capacity: 10 l Max heating operating pressure: 3 bar Degree of protection (IEC 60529): IP X5D Rated Electric Power: 106W NOx degree: 6 Dimensions (hxlxp): 763x450x345; 38.5kg Luna Duo-tec E and Duo-tec Compact E: the already well-known Baxi boilers present themselves today with a new aesthetic, increasingly modern and attentive to new design trends, which allows them to be inserted in any living context. The control panel has also been completely renewed and is equipped with a new backlit LCD display that is even clearer and simpler to use thanks to dedicated and independent keys. The new boilers, even more beautiful and modern thanks to the restyling, however keep intact the characteristics that have always distinguished the Duo-tec range: Reliability: robustness, durability and reliable performance; Efficiency and savings: the reduction of on/off cycles translates into considerable benefits in terms of energy savings and lower emissions; Completeness of the range: heating only models, with instant DHW production, and also the compact version with the possibility of outdoor installation. The range has been further enriched with the new models equipped as standard with the Baxi Mago modulating chronothermostat with integrated wi-fi. Wide modulation range 1:7 Greater efficiency given by less switching on and off: with a high modulation ratio, the reduction of continuous switching on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions Adjustment of the thermal power produced to the dissipated power thus avoiding excessive overheating/cooling of the premises. Digital control panel The Duo-tec E range of boilers is equipped with a new digital control panel with backlit LCD display that is even clearer and simpler to use thanks to dedicated and independent keys for regulating the temperature of the domestic hot water and heating. The display allows you to view all the information and set the operating parameters in an intuitive and immediate way. By pressing the dedicated key, it is possible to view numerous information regarding boiler operation, such as: heating system water pressure (electronic pressure transducer present in the hydraulic group); heating flow/return temperature; external temperature (with external probe installed); domestic hot water temperature. Gas Adaptive Control It is an innovative system which, thanks to a new control electronics and a new electronic gas valve, guarantees automatic control of combustion to constantly maintain maximum efficiency values. Advantages: • there are no manual interventions - reduced measurements, calibrations or nozzle changes; • with this system, the boiler self-adapts to the quality of the gas and the length of the flue gas pipes, keeping efficiency constant; • the boiler also constantly regulates itself to maintain the maximum efficiency values, favoring a reduction in gas consumption and generating less pollution thanks to the continuous control of emissions. Duo-tec E range: compatibility with Baxi Mago The entire Duo-tec E range is compatible with the Baxi Mago, available as an accessory, for remote boiler control. The boilers of the Duo-tec E range, if combined with the Baxi Mago, access the 65% deduction provided for by the 2019 Ecobonus. BAXI MAGO is the new generation chronothermostat designed to simplify the life of installers and users. An innovative and design tool, which combines extreme practicality with a modern, captivating aesthetic with a strong appeal. Furthermore, BAXI MAGO thinks about your savings: in fact it communicates with the boiler, optimizing consumption. And when you're away from home or just don't feel like getting off the sofa? BAXI MAGO can be managed from the app, comfortably with your smartphone. Smartphone management Automatic and fast programming Consumption under control Contact with the CAT Integrated systems: hydraulic, thermoregulation and control Electric three-way diverter valve (also for heating only models) Pre-mix burner in stainless steel Stainless steel water/fumes exchanger Increased DHW exchanger in stainless steel which allows the boiler to condense even in DHW operation Modulating fan with electronic speed variation Automatic by-pass High efficiency circulation pump with total modulation Pump anti-blocking system and three-way valve which intervenes every 24 hours Heating circuit safety valve at 3 bar Standard climate control (with external probe available as an option) Arrangement for connection to a zone system Safety thermostat against overheating of the water/fumes exchanger Hydraulic pressure switch which blocks the gas in case of water shortage NTC safety probe against fume overheating Temperature control using NTC probes Total antifreeze device Electronic thermometer Heating circuit digital pressure gauge Also for outdoor installation Duo-tec Compact E boilers can be installed outdoors in partially protected places thanks to the new top cover kit and bottom closure kit (available as accessories). In fact, the Duo-tec Compact E range is equipped AS STANDARD with an electronic antifreeze system which guarantees operation down to a temperature of -5 °C: the IPX5D protection also protects the electrical parts from jets of water which may come from all directions. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.223,00
ATTENZIONE IL PRODOTTO È NUOVO E FUNZIONANTE, MA PRESENTA UN' AMMACCATURA E BOZZATURA LATERALE, DANNEGGIAMENTI SULLA PARTE FRONTALE, CANNA FUMARIA DANNEGGIATA E L'IMBALLO È USURATO (PER MAGGIORI INFORMAZIONI SUI DANNEGGIAMENTI VISUALIZZA LE FOTO ACCANTO ALL'IMMAGINE PRINCIPALE). ATTENZIONE LA CALDAIA VIENE FORNITA A METANO. FUNZIONAMENTO A GPL TRAMITE REGOLAZIONE DA PARTE DEL CENTRO ASSISTENZA AUTORIZZATO. PER INFO, CONTATTARE PREVENTIVAMENTE L'ASSISTENZA BAXI DI ZONA Caldaia Baxi Luna Duo-tec E 33 a condensazione Low NOx completa di kit scarico fumi Metano o Gpl Caratteristiche Tecniche Tipologia: Caldaia Murale a condensazione; Modello: Luna Duo-Tech Compact E; Classe di efficienza Energetica: A; Profilo di Carico: XXL; Alimentazione: Metano/Gpl Gas Adaptive Control; Performance in Riscaldamento: Portata termica nominale riscaldamento: 28.9 kW; Portata termica ridotta: 4.8 kW; Potenza termica utile a potenza termica nom. e regime ad alta temp.* P4: 28 kW; Potenza termica utile al 30% potenza term. nom. e regime a bassa temp.** P1: 9.4 kW; Temperatura minima di funzionamento: -5°C ; Capacità vaso espansione: 10 l; Regolazione temperatura acqua circuito riscaldamento: 25-80°C; Pressione min/max acqua circuito riscaldamento: 0.5/3 bar; Performance in Sanitario: Portata termica nominale sanitario: 34 kW; Potenza termica nominale sanitario: 33 kW; Regolazione temperatura acqua sanitaria: 35-60 °C; Produzione acqua sanitaria ?T 25°C: 18.9 l/min ; Portata minima acqua circuito sanitario: 2 l/min; Rendimenti: Rendimento utile a potenza termica nom. e regime ad alta temp: 88.1 %; Rendimento utile al 30% potenza term. nom. e regime a bassa temp: 98.1 %; Rendimento utile (pci) Pn - temperatura media 70°C: 97.8 %; Rendimento utile (pci) al 30%- temperatura di ritorno 30°C: 108.9 %; Rendimento utile (pci) intermedio- temperatura media 70°C: 98.2 %; Potenza elettrica nominale: 106 W; Consumo ausiliario di elettricità modo stand-by: 0.003 kW; Emissioni di ossidi di azoto NOx: 15 mg/kWh; Livello di potenza sonora, all'interno: 53 dB; Dimensioni: (HxLxP): 763x450x345 mm;Peso: 39.5 kg; Luna Duo-tec Caratteristiche Generali Nuovo design moderno ed elegante per tutta la gamma Ampio campo di modulazione fino a 1:7 (1:6 mod. 1.12) maggiore efficienza e silenziosità GAC (gas adaptive control): controllo automatico della combustione Pannello comandi digitale con ampio display LCD retroilluminato Predisposizione per abbinamento con il sistema solare integrato Baxi Allacciamento a tubo di scarico Ø50 mm rigido e flessibile: soluzione per risanamento canne fumarie - per il mod. 24 kW lunghezza totale 40 metri (aspirazione+scarico) Sistema idraulico Valvola deviatrice a tre vie elettrica (anche modelli solo riscaldamento) Bruciatore a premiscelazione in acciaio inox Scambiatore acqua/fumi in acciaio inox Scambiatore sanitario maggiorato in acciaio inox che permette alla caldaia di condensare anche in funzionamento sanitario Ventilatore modulante a variazione elettronica di velocità By-pass automatico Pompa di circolazione ad alta efficienza a modulazione totale Sistema antibloccaggio pompa e valvola a tre vie che interviene ogni 24 ore Valvola di sicurezza circuito riscaldamento a 3 bar Sistema di termoregolazione Regolazione climatica di serie (con sonda esterna disponibile come optional) Predisposizione per il collegamento ad un impianto a zone Sistema di controllo termostato di sicurezza contro le sovratemperature dello scambiatore acqua/fumi Pressostato idraulico che blocca il gas in caso di mancanza d’acqua Sonda NTC di sicurezza contro le sovratemperature dei fumi Controllo temperature mediante sonde NTC Dispositivo antigelo totale Termometro elettronico Manometro digitale circuito riscaldamento Garanzia Prodotto La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.
€1.060,00
