NB: BOILER CANNOT BE INSTALLED IN PIEDMONT AND LOMBARDY DUE TO CURRENT REGULATIONS. Hermann Saunier Duval Gas Condensing Boiler Model THEMIS CONDENS 24 kW Methane Complete with Fume Exhaust Kit + FREE DIRT SEPARATOR Technical features ErP efficiency class in heating/DHW: B/A Sanitary load profile: XL Type: Heating and domestic hot water Heating Nominal power P min/max heating 80/60°C: 12.2/24.1 kW Partial load efficiency 30% 40/30 °C %: 99.7 Sanitary Min/Max Rated Power (60°C): 12.5/24.0 kW Specific flow rate (∆T=25 K): l/min 13.8 Electrical characteristics Max power consumption: W 60 Supply voltage/frequency: V/Hz 230/50 Dimensions: Dimensions (h x w x d): 720 x 405 x 330 mm METHANE version THEMIS CONDENS Themis Condens is the ideal condensing solution for replacing traditional wall-mounted boilers that work with high temperature radiators in apartments. The boiler has all the characteristics of simplicity in both installation and management. Themis Condens was developed to give the right comfort, both for the production of domestic hot water and to provide the ideal climate in the rooms. Specially designed for replacement in high temperature systems Small size Simplicity of management Reduced electricity consumption thanks to the instantaneous high efficiency pump Themis Condens combines the simplicity of the traditional boiler with the efficiency of condensing boilers. Themis Condens runs on methane and can be converted to run on propane. Themis Condens is available in the power of: 24kW for heating and 24kW for domestic hot water production. 27kW for heating and 27kW for domestic hot water production Characteristics: Can be installed indoors. Continuous domestic hot water (DHW) production up to 16 l/min Small dimensions: 72cm high, 40 wide and 33 deep (24 kW) The boiler features a new high-efficiency pump with high performance and a 7-litre expansion vessel. ErP efficiency class B in heating, A in DHW with XL profile. Reliability and Hermann Saunier Duval standard quality Specific for high temperature systems Large passages in the primary exchanger Reduced electricity consumption thanks to the high efficiency pump Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: PRODUCT ARRIVES IN MID-FEBRUARY ARISTON EGIS PREMIUM EVO EXT 25 EU CONDENSING BOILER COMPLETE WITH METHANE FUME KIT - NEW ErP Technical features Product code: 3300763 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 23.5/2.5 Max/min heating thermal power (80°C-60°C) kW 22.9/5.3 Efficiency at nominal heat input (60/80°C) % 97.5 Efficiency at nominal heat input (30/50°C) % 103.9 Efficiency at 30% at 30°C % 108.2 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 25/45 Specific flow rate in DHW (10 min. with ∆T=30°C) litres/min 10.5 Quantity of hot water ∆T=25°C litres/min 13.1 Quantity of hot water ∆T=35°C litres/min 9.4 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 87 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 770/505/240 Extremely small dimensions to adapt to any space problem. METHANE power supply Standard: Sensys system manager with integrated time programming General characteristics Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. EVO: energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the energy certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston satisfies all the indications envisaged for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energy. Egis Premium Evo EXT EGIS Premium Evo EXT is the wall-mounted condensing boiler designed for outdoor installation. Thanks to its small size and low weight, installation is extremely simple. This without giving up the safety that distinguishes Ariston, i.e. exceptional resistance to cold (up to -15°C) and electrical protection from water and dust that reaches the highest levels (IPX5D classification). Simplicity and with reduced consumption thanks to the 1:4 modulation ratio and the high-efficiency circulator with continuous modulation. Operation only with methane gas Characteristics: Wall mounted condensing boiler for outdoors with auto function Sensys system manager with integrated time programming Continuous modulation high efficiency circulator Modulation ratio 1:4 Electro-galvanized casing for outdoors Prepared for integration in system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort External probe integrated in the boiler Anti-freeze, anti-limescale and anti-blocking circulator protection Aluminum isothermal primary exchanger Cold water inlet and heating return filters 60mm split exhaust Operation only with methane gas Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons Acoustic comfort Acoustic comfort is further guaranteed by the introduction of the new silencer. For the Genus Premium Evo EXT thanks also to the high modulation ratio 1:10, the continuously modulating pump and the presence of side sound-absorbing panels. High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

OFFER VALID UNTIL STOCKS LAST THE BOILER IS BORN WITH METHANE. THEREFORE, THE STANDARD TRANSFORMATION KIT WILL BE SUPPLIED. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Technical features Model : Class One 24 Product code: 3301021 Power supply: LPG Wi-Fi Optional Energy efficiency Energy efficiency class in heating: A Sanitary energy efficiency class: A Withdrawal profile : XL Combustion Nominal heat input in heating : 3.7 ~ 22.0 kW Nominal heat input in DHW : 3.7 ~ 26.0 kW Useful thermal power in heating: 3.4 ~ 21.4 kW Returns Efficiency at nominal heat input 60°/80°C : 97.5% Efficiency at nominal heat input 30°/50°C: 107.3% Return at 30% / 30°C : 109.8% Performance High temperature heating temperatures : 82° ~ 35° C Low temperature heating temperatures : 45° ~ 20° C DHW temperature : 60° ~ 36° C Quantity of hot water at 25°: 14.5 l/min Quantity of hot water at 35°: 10.4 l/min Minimum operating temperature : >0° C Minimum operating temperature with antifreeze kit: -5° C Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Absorbed electrical power: 77.0 W Degree of protection : X5D IP Dimensions and weight Dimensions (WxHxD): 400x745x315 mm Wall mounted condensing boiler Ariston CLAS ONE Ariston excellence guaranteed for 10 years thanks to the Protezione 10 total assistance programme. Latest generation condensing boiler set up for Wi-Fi connection with the CUBE S NET thermostat Prepared for Ariston NET With Ariston NET you have comfort at your fingertips. Remote control, consumption reports and online technical support, all in a free smartphone App Protection 10 The excellence of Series ONE is guaranteed for 10 years with the total protection 10 assistance program Small size Small footprint for easy installation New PER4MANCE system 4 technologies for exclusive performance New XtraTech TM heat exchanger, maximum quality. Absolute efficiency, energy class A+ Always connected with Ariston NET Full control, total comfort Heating with maximum duration over time with the XtraTech heat exchanger The new patented ExtraTech heat exchanger is the heart of the ONE condensing technology for heating, designed to guarantee performance with maximum durability over time Absolute efficiency, energy class A+ with Ignition System for improved functionality The ONE condensing technology and the thermoregulation accessories improve efficiency and performance, reaching up to energy class A+. Alteas ONE and Genus ONE are also equipped with the innovative Ignition System with electronic combustion control and gas adaptability. The system is able to automatically identify the characteristics of the gas, providing constant heating performance, advanced control and safety in all conditions Total Comfort Complete control is ensured every day with the thermo functions A unique set of innovative smart functions for a fast and stable heating temperature and easy customization able to satisfy every need Always connected with Ariston NET With Ariston NET it is possible to set, modify and control the heating, cooling and hot water temperature at any time, from your smartphone or PC, wherever you are Ariston quality forever at your home 100% GUARANTEED BY ARISTON Every single component is developed with the aim of guaranteeing long-lasting performance and high efficiency, with the guarantee of the Ariston brand. 100% CHECKED AND TESTED Every single Ariston product is rigorously tested in terms of quality, efficiency and safety before being delivered, with superior results guaranteed by our commitment. 100% BUILT TO LAST Strong and super resistant materials, components and products developed to perform in extreme conditions to deliver high-level results with maximum durability A masterpiece of Italian style The improved design of the ONE Series is based on innovative lines, new materials and technological user interfaces for an even more comfortable experience. The touch screen display is a solution that allows easy temperature management, while the compact structure has been redesigned with internal components and a layout designed for easy access even with reduced dimensions. With the front panel in tempered glass, scratch resistant and easy to clean, Alteas ONE is made to withstand high temperatures and to always be super safe. Product Guarantee : All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Easy to use thanks to the control panel equipped with knobs and backlit LCD display • Easy installation thanks to ultra-compact dimensions (700x395x279 mm – including knobs) and low weight (26 kg) • Easy replacement of conventional boilers thanks to central flue gas outlet • Modulation range 1:5 greater efficiency and silence • High efficiency circulation pump • Arrangement for combination with the Baxi integrated solar system • Ø 80 double exhaust as standard • Connection to rigid and flexible Ø 50 mm exhaust pipe: solutions for restoring flues, total length (exhaust + suction) 40 meters • Connection to pressurized collective flues • Boilers running on methane that can be converted to LPG and propane air by means of a specific regulation (conversion kit not necessary ) TECHNICAL FEATURES – Installation type: B23-B23P-B33-C13-C33-C43-C53-C63-C83-C93 – DHW nominal heat input: 20.9 kW – Sanitary nominal thermal power: 30 kW – Nominal heating heat input: 24.7 kW – Heating rated thermal power 80/60°C: 24 kW – Heating rated thermal power 50/30°C: 26.1 kW – Reduced thermal power 80/60°C : 5.6 kW – Reduced thermal power 50/30°C: 6 kW – Efficiency at 30%: 105.8% – Nominal efficiency 80/60°C: 97.5% – Nominal efficiency 50/30°C: 105.8% – Seasonal space heating energy efficiency class: A – Seasonal energy efficiency class of the sanitary fixture: A – Water heating – Load profile: XL – NOx class 5 – Domestic hot water production: ∆T 25°C: 13.8 l/min – Category II2HM3B/P appliance operating on gas type G20 – G230 – G30 – G31 – Electronic ignition with flame ionization control – Degree of protection: IPX5D – Primary water/gas coil exchanger in AISI 316L stainless steel – Secondary water/water exchanger in stainless steel – Electric 3-way diverter valve – Modulating fan with electronic speed variation – Automatic by-pass on the heating circuit – Digital and analog pressure gauge on the heating circuit – Heating expansion tank with capacity 7 l and preload 0.8 bar – High efficiency ErP full modulation circulation pump with built-in deaerator – Hall effect DHW flowmeter for detecting hot water withdrawal – DHW operation with minimum water pressure of 0.15 bar and minimum flow rate of 2 l/min. – Inspectable filter on loading water inlet – Primary circuit safety valve at 3 bar – Heating water temperature adjustment range: 25÷80°C – Domestic water temperature adjustment range (in the case of combination with a boiler): 35÷60°C – Minimum operating temperature: – 5°C – Dimensions hxwxd: 700 x 395 x 279 mm – Weight 26kg CONTROL SYSTEM – Temperature control using NTC probes – Pump post-circulation in heating function – Safety thermostat against overheating of the water/fumes exchanger – Hydraulic pressure switch which blocks the gas in case of water shortage – Pump electronic control blocked – Pump anti-blocking system and 3-way valve which intervenes every 24 hours – NTC safety probe against fume overheating – Total antifreeze device which intervenes with temperatures below 5°C – Electronic thermometer – Display of heating circuit pressure on control panel   THE ADVANTAGES OF PRIME EASY TO INSTALL The ultra-compact dimensions 700x395x279 mm and the weight of just 26 kg reduce installation time. The new Prime has the same distance between centers of the hydraulic connections of the conventional BAXI boilers to be replaced. Front access to the electrical connection also speeds up connection times. The fixing bracket supplied as standard and the visible hooks facilitate wall mounting.       LOWER ENERGY CONSUMPTION Thanks to the condensing technology, the high efficiency pump and the series of modulating room thermostats available as an accessory. The new regulation 7129-3:2015 prescribes the possibility of creating collective flues in positive pressure only for type C condensing appliances. It is possible to connect to a collective flue in positive pressure only appliances declared suitable by the manufacturer for this application and equipped with a non-return device (clapet), designed to prevent the combustion products from flowing out through appliances connected and temporarily switched off; the smoke non-return valve is an integral part of the appliance.         THE REGULATION 7129-3:2015 Regulation 7129-3:2015 prescribes the possibility of creating collective flues in positive pressure only for type C condensing appliances. Only devices declared suitable can be connected to a positive pressure collective flue by the manufacturer for this application and equipped with a non-return device (clapet), designed to prevent the products from combustion to flow through appliances connected and momentarily switched off; the smoke non-return valve is part component of the appliance.     CLAPET (SMOKE NON-RETURN VALVE) Included in the duct downstream of the air-gas group fan.           CONNECTED TO COLLECTIVE PRESSURIZED FLUES Thanks to the integrated flue non-return valve (clapet), Prime is designed for connection to pressurized collective flues.                           SMOKE PIPES Ø50 MM Possibility of restoring flues with Ø50 mm exhaust hose (up to 40m of exhaust)     FLEXIBILITY IN THE REPLACEMENT Easy replacement of old standard boilers, thanks to the central flue outlet and the separate adjustable outlet supplied as standard.   The Ø 60/100 coaxial drain is available as an accessory that can be combined with a pipe extension and a 60/100 diameter 90° elbow (360° adjustable).   To facilitate replacement in installations where space is limited (flue gas outlet at the rear of the boiler), the new accessory is available with a lowered coaxial 90° bend.   For more information, download the following documentation: PRIME 24 TECHNICAL DRAWINGS     NEW COMBUSTION GROUP The Prime combines the performance of the stainless steel exchanger with the advantages of a new generation burner integrated with an innovative cold closing door.       The new cylindrical burner ensures greater thermal and acoustic comfort, and reduced NOx and CO emissions thanks to greater flame stability. The new cold door reduces losses by 75% with surface temperatures below 20°C, guaranteeing significant savings in stand-by and during operation, speeding up maintenance, as there is no need to wait let it cool down.

Read more less

Overview BIASI INOVIA COND PLUS 25S CONDENSING METHANE LPG BOILER - NEW ErP, SEALED CHAMBER COMPLETE WITH FUME EXHAUST KIT: Inovia Cond Plus is the new BIASI range of wall mounted condensing boilers: excellent performance thanks to the new heat exchanger and ease of use thanks to the panel digital control with large displays. Technical specifications Model: Inovia Cond Plus 25S Energy label specifications according to the European ErPÿ directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Heating/DHW maximum useful power: 19.3/25.1ÿkWÿ Heating/DHW nominal heat input: 20/26 kW Yield name 60ø/80øC:ÿ96.7% Yield at 30% load: 107.4% High yields (in compliance with yield directive 92/42 CEE and Legislative Decree 311/06) Sanitary comfort( EN 13203)ÿ 8 liter expansion tankÿ Degrees of protection IPX5Dÿ Maximum flow rate (T=25 K) / (T=35 K): 14.4/10.3 l/minÿ Specific sanitary flow rate (T=30 K): 12.0ÿl/minÿ Dimensions hxwxd: mmÿ700 x 400 x 290; 32kg NOx class : 6 ÿMETHANEÿorÿLPG power supply Main features Inovia Cond Plus Wall mounted condensing boilersÿ Inovia Cond Plus is the new BIASI range of wall-mounted condensing boilers: excellent performance thanks to the new heat exchanger and ease of use thanks to the digital control panel with large displays. Available in the versions for heating and domestic hot water production and for heating only, Inovia Cond Plus presents a complete range of powers, 25 and 35 kW combi models and 25 and 35 SV models, in the same extremely compact dimensions (700 x 400 x 290mm). Inovia Cond Plusÿhas its strength in the innovative heat exchangerÿdesigned to provide high yields that last in the digital control panel, designed to communicate with the user in an easy and comfortable way. Like the entire BIASI condensing range, Inovia Cond Plus allows you to obtain maximum savings from climatic thermoregulation, based on the system in which the boiler is installed. High yields (complies with 92/42 EEC yield directive and Legislative Decree 311/06) Sanitary comfort (EN 13203)ÿ Primary and condensing heat exchanger in stainless steel withÿaluminium coatings to offer maximum resistance to corrosionÿ Total premix burner, built in stainless steel (Class NOx5) Sanitary plate heat exchanger in INOXÿ steel High efficiency pump with low energy consumption 8 liter expansion tankÿ Maximum power adjustable according to the systemÿ Degrees of protection IPX5Dÿ Can be installed in a partially protected placeÿ Integration with BIASI solar systems, using a solar kitÿ Innovative digital control panelÿ Digital pressure readoutÿ Arrangement for external probe remote controlÿ Possibility of managing a zone valve by remote control in multi-zone systems. High circulation primary heat exchanger Biasi produces the new Steelcoil compound exchanger with a stainless steel spiral enclosed in an aluminum shell. Thanks to the large exchange surface of the coil, greater thermal efficiency is guaranteed with a lower loss of charge and easier cleaning. The ease of cleaning and the sturdiness of this exchanger are one of the main strengths of the product which can be used on new systems but also on old systems in case of renovations. Steelcoil integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the monspira. Does the absence of parallel circuits guarantee an easy cleaning operation? of the exchanger and the elimination of any air present in the system circuit. Thermoregulationÿ By connecting the external probe and the remote control (optional) directly to the boiler, climatic regulation can be used. Inovia Cond Plus will adapt the water temperature of the system to the external climatic conditions, guaranteeing the achievement of the desired room temperature without waste and optimizing consumption. By using climatic regulation, the regulation efficiency is also increased, giving greater value to your home. All ready for Energy Labeling What is it about From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres or As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. It's about me tooÿ YES, it affects everyone: professionals and end users The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. Supplier's responsibility The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. Responsibilities of Resellersÿ First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ARISTON GENUS PREMIUM EVO 35 EU CONDENSING BOILER COMPLETE WITH METHANE FUME EXHAUST KIT - ErP Technical features Product code: 3300706 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 31/3.5 Max/min heating thermal power (80°C-60°C) kW 30.1/3.4 Efficiency at nominal heat input (60/80°C) % 97.7 Efficiency at nominal heat input (30/50°C) % 106.5 Efficiency at 30% at 30°C % 108.7 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Specific flow rate in sanitary mode (10 min. with ∆T=30°C) litres/min 16.0 Quantity of hot water ∆T=25°C litres/min 19.3 Quantity of hot water ∆T=35°C litres/min 13.8 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 77 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 770/400/385 CNG or LPG power supply Kit for conversion from methane to propane supplied Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. EVO : energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the energy certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston satisfies all the indications envisaged for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energy. Genus Premium Evo The Genus Premium Evo wall-mounted boiler is the maximum expression of the Ariston range. Thanks to the condensing technology, by recovering the energy of the exhaust fumes, it generates an increase in the calorific value which makes it possible to eliminate waste (of energy) and to obtain higher thermal efficiency than conventional boilers. Genus Premium Evo offers even greater performance thanks to the innovative technology that allows it to self-regulate according to variations in the external and internal temperature of the room, allowing energy savings of up to 35% compared to an older generation boiler. It is available in the heating and domestic hot water production version in 3 powers: 24-30-35 kW (sealed chamber). Characteristics: Can be installed in partially protected places Large backlit dot matrix screen Continuous modulation high-efficiency circulator: for optimizing consumption and maximizing performance. Modulation ratio 1:10 - Automatic power regulation according to the heating request. Acoustic comfort guaranteed by the lower number of boiler on and off cycles, new silencer and sound-absorbing panels Prepared for integration in system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort Isothermal primary heat exchanger in stainless steel Increased sanitary exchanger Cold water inlet and heating return filters Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons Acoustic comfort Acoustic comfort is further guaranteed by the introduction of the new silencer. For the Clas Premium Evo thanks also to the high modulation ratio of 1:10, the continuously modulating pump and the presence of side sound-absorbing panels. High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ARISTON GENUS PREMIUM EVO CONDENSING BOILER IN 25 EU COMPLETE WITH LPG - ErP FUME KIT Technical features Product code: 3300736 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: For heating and domestic hot water production Forced draft sealed chamber Nominal heat input in heating max/min kW 22/2.5 Max/min heating thermal power (80°C-60°C) kW 21.5/2.4 Efficiency at nominal heat input (60/80°C) % 97.8 Efficiency at nominal heat input (30/50°C) % 106.2 Efficiency at 30% at 30°C % 109 Performance stars (dir. 92/42/EEC) ★★★★ Min/max heating temperature (high temperature range) °C 35/ 82 Min/max heating temperature (low temperature range)°C 20/ 45 Min operating temperature* °C -15 Specific flow rate in DHW (10 min. with ∆T=30°C) litres/min 12.2 Quantity of hot water ∆T=25°C litres/min 14.6 Quantity of hot water ∆T=35°C litres/min 10.4 Comfort performance stars (EN13203) ★★★ Supply voltage/frequency V/Hz 230 / 50 Total absorbed electric power W 78 Degrees of protection of the electrical system IP X5D Dimensions (H x W x D) mm 1140/590/240 Extremely small dimensions to adapt to any space problem. METHANE power supply Standard: Sensys system manager with integrated time programming General characteristics Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. CLAS PREMIUM EVO, exploits the phenomenon of condensation in its favor by reusing the energy of the exhaust fumes and increases the useful calorific value, thus reaching the thermal efficiency of over 107%. Furthermore, during this process, most of the harmful combustion products for the environment and health, they are eliminated together with the condensed water. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. EVO: energy saving becomes reality, for everyone's well-being Among the measures aimed at reducing the energy consumption of buildings (European Directive 2010/30/EC), the Italian legislation has introduced "The obligation of the energy certificate of the building" in the purchase and sale of new and existing buildings. They have also been extended until throughout June 2013, bringing them to a value of 50%, the "tax credit deductions relating to building renovations and energy efficiency interventions". For the purpose of achieving the national objectives envisaged on the coverage of consumption through renewable energy sources (European Directive 2009/28/EC) it also requires and promotes "the use of heating systems operating on renewable energy". With the EVO range, Ariston responds to all the indications foreseen, for having "low energy consumption buildings", guaranteeing optimal integration with systems using renewable energies. Genus Premium Evo IN Genus Premium Evo In is the wall-mounted condensing boiler expressly designed for built-in installation. Small dimensions and reduced weight, its implementation is extremely simple. This without renouncing the safety that distinguishes Ariston, i.e. exceptional resistance to cold (up to -15°C) and electrical protection from water and dust that reaches the highest levels (IPX5D classification). High efficiency product with reduced consumption thanks to the 1:10 modulation ratio and the high efficiency circulator with continuous modulation Characteristics: Built-in condensing boiler with auto function and info top Sensys system manager with integrated time programming Continuous modulation high efficiency circulator Modulation ratio 1:10 Universal built-in unit in electro-galvanized sheet metal (to be ordered with separate code) Possibility of outdoor installation thanks to all weather protection systems. Prepared for integration in system configuration through the new Bus Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation Arrangement for solar system management Car function and comfort External probe integrated in the boiler Semi-automatic filling Circular anti-freeze, anti-limescale and anti-blocking protection Increased sanitary exchanger Cold water inlet and heating return filters Convenience function: The Comfort function speeds up the delivery of domestic hot water, reducing waiting times down to just 5”. This service can be customized by choosing between two modes of use: COMFORT PLUS (hot water immediately ready every time the tap is opened in just 5 seconds) COMFORT (hot water ready for 30 minutes after the last withdrawal so as not to give up savings) car function: It is truly possible to combine maximum comfort with reduced consumption, thanks to the intelligent management logic of the new boilers and the new technology that governs them. By activating the AUTO function, the Ariston boiler chooses the best operating mode based on the environmental conditions, the connected external devices and the required performance. Impossible to compare this ability to interpret and respond to external stimuli with what has been achieved so far. AUTO does not fear comparisons Acoustic comfort Acoustic comfort is further guaranteed by the introduction of the new silencer. For the Genus Premium Evo EXT thanks also to the high modulation ratio 1:10, the continuously modulating pump and the presence of side sound-absorbing panels. High efficiency circulator with continuous modulation: It allows automatic adaptation of the power based on the temperature of the system, guaranteeing boiler performance and reducing electricity consumption. Optimization of thermal efficiency. Optimization of comfort with constant temperature. Maximum silence. High efficiency The condensing technology makes it possible to achieve high energy efficiency thanks to the increase in the calorific value generated by the reuse of the energy of the exhaust fumes, allowing for a higher thermal efficiency. The future of the planet and your comfort are the main objectives of Ariston condensing technology Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.  

Read more less

ATTENTION IN THE ABSENCE OF THIS PRODUCT, THE MODEL PIGMA ADVANCE EXT 25 WILL BE SUPPLIED Overview CHAFFOTEAUX PIGMA GREEN EXT Ebus2 25 EU CONDENSING BOILER Cod. 3310443, COMPLETE WITH FUME KIT - NEW ErP 2015: Condensing technology with minimum bulk and maximum installation versatility make Pigma Green Ext Ebus2 EU the best choice where living spaces are you don't want to give up comfort and savings. Technical specifications Product code: 3310443 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency Class A Withdrawal profiles: XL Characteristics of heating/sanitary exercises: Nominal heat input in heating max/min (Hi) Qn: 22/5.5 kW Useful heat output 80/60øC in heating/sanitary max/min:ÿ21.5/5.4kW Nominal heat input in sanitary(60/80øC) max/min:ÿ26/5,5 kW Efficiency at nominal heat input:ÿ97.5% Efficiency 30% of nominal heat input:ÿ109% Sanitary comfort performance starsEN13203: *** Energy efficiency stars: (dir 92/42/CEE) **** Capacity of the expansion vessel: 8 lt Port. specific in healthcare (10 min. with T= 30øC): 12.2 l/min Minimum withdrawal:ÿ<2ÿl/min Total absorbed electric power: 76 W Degrees of protection for the electrical system: IPÿX5D Dimensions hxwxd: mmÿ766x505x240ÿ; 32kg LPG fuel supply or Features list PIGMA GREEN EXT Ebus2 EU Condensing technology with minimum bulk maximum installation versatility makes Pigma Green Ext Ebus2 EU the best choice where living spaces are precious and you don't want to give up comfort and savings. Resistant to corrosion, wind and frost, it can be installed anywhere and conveniently control all functions via the standard Expert Control system manager. Pigma Green Ext Ebus2 can be perfectly integrated with solar thermal systems and modules for the management of multi-zone systems, even with different temperatures, to make any design solution simple. Sanitary comfort Increased plate heat exchanger in stainless steel. 3-star sanitary comfort, the maximum unexpected by the EN 13203 standard. 12 l/min (T= 30°C) domestic hot water flow rate, measured in compliance with standard EN 625. Sanitary circuit managed by four probes and a flowmeter, to eliminate waiting times and have a constant temperature, even in the case of small withdrawals. Perfectly integrable with thermal solar systems, forced and natural circulation Daily and weekly hourly programming of the DHW exchanger pre-heating periods directly from the Expert Control system manager. Heating comfort ÿRendimentfinal 109% with energy savingsfinal 35%. 4-star combustion efficiency according to the EN 92/42 standard. Automatic regulation system, which can be activated directly from the Remote Control, to obtain the best heating operating regime in all environmental conditions. Useful thermal power up to 23.5 kW. Modulation ratio 1:5. Reduced polluting emissions, NOx class 5. Heating circuit pressure sensor with display on Expert Control. Modulating circulatorÿ to improve acoustic comfort and reduce electricity consumption. Differentiated climatic thermoregulation of 3 circuits, according to the ambient and external temperature. Operation management and programming through the Expert Control system manager: operating modes and temperatures, self-diagnosis, daily and weekly programming, adjustment information and history of the latest faults. Convenience of installation use Semi-automatic fillings that can be activated from the Expert Control system manager. Expert Control system manager and external probe as standard. Adjustment of operating parameters directly to Expert Control system manager. Arranged for the control of 3-circuit system management modules at different temperatures. Prepared for the management and integration of thermal solar systems (standard solar probe). Electrical protection degrees IPX5D and operation guaranteed up to -15øC **. Commissioning made easier: automatic de-aeration function and combustion regulation with direct access. ERP extension From 26 September 2015 the directives of the European Commission concerning eco-design and energy labeling will apply. These two directives aim to achieve savings in one of the most polluting and most energy intensive sectors: construction For placing on the European market, the directive on ÿeco-designÿ(ErP notcome®ÿEnergy Related Productsÿ¯) imposes a minimum energy efficiency for heating devices and hot water production in domestic premises. The directive applies to: generators with a capacity of less than 400 kW water heaters with a capacity of less than 400 kW, kettles with a capacity of less than 2000 litres As in the household appliances sector, the energy labelingÿof products, with a capacity of less than 70 kW, will give consumers simple, recognizable information which allows them to make comparisonsÿon the performance and energy consumption of the product they wish to purchase. The energy label will be included in all boilers, water heaters and storage tanks placed on the market from 26 September 2015. The information indicated on the energy labelÿwill allow professionals to recommend the right productÿÿindividuals to benefit from the information available. The user will be able to easily compare the performance of the products. From 26 September 2015, the label will be present on the following products: boilers, electric water heaters, thermodynamic water heaters, solar water heaters, storage tanks, heat pumps, solar systems and control systems. The company that supplies the product on the market is required to equip its system devices with the following documentation: product energy label;ÿ product data sheet;ÿ system energy label in addition to that of the product, both if it sells a system that includes the product in question, and if this, in the future, can be sold combined with other additional devices;ÿ technical data sheet of the system with the parts relating to the products and the system already completed. First of all, it should be clarified that the reseller can be anyone who sells, rents, offers for rent/sale and exhibits a device/system to the public. Therefore, even professionals such as plumbers, installers, designers can fall into this category. All bound to ensure that: all appliances and/systems having their respective labels and making sure they are clearly visible;ÿ all appliances and/systems must always be accompanied by the obligatory technical data sheets;ÿ every type of advertising material, technical promotional material which shows energy data and price indications, contains an indication of the energy efficiency class. The new ErP regulations ENERGY LABELLING: Appliances for space heating and the production of hot water will have to be equipped with the new energy label which will report the energy class and the main performance data. The energy class must also be mentioned in the technical, commercial and advertising documentation of the appliances. ECODESIGN (ErP): The new ErP regulations impose the minimum energy efficiency that space heating and hot water production appliances must achieve in order to obtain the CE mark and be marketed in Europe. These new limits will exclude obsolete technologies from the market, significantly raising the level of energy efficiency of products. PRODUCT LABEL There are different labels depending on the type of appliance. Those with efficiency classes A, A+ and A++ certify products with the highest performance. Furthermore, two different classifications are foreseen for domestic heating and for hot water production services, so much so that mixed products must show both classifications. In addition to the energy class, the labels contain other information, so that the end customer can make his choice in the most aware way possible. SYSTEM LABEL In addition to the product label, the system label is also providedÿin cases where a series of appliances combined with each other is offered. This label must also be included in the technical and commercial documentation of the system. Those proposing such systems will have to calculate the performance using a predefined calculation algorithm and display the label so as to inform the end user in the best possible way. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Ferroli condensing boiler Bluehelix Tech RRT 30 H Heating only METHANE OR LPG Complete with flue gas kit - New Technical features: ERP Class (Class G - A++) A Heating max / min heat input (Hs) kW 30.6 / 6.4 Max / min heat output heating (80/60°C) kW 30 / 6.3 Max / min heat output heating (50/30°C) kW 32.5 / 6.9 Efficiency Pmax / Pmin (80-60°C) (Hi) % 97.9 / 98.0 Efficiency Pmax / Pmin (50-30°C) (Hi) % 106.1 / 107.5 Efficiency 30% 109.5 Max / min heating pressure bar 3 / 0.8 Empty weight kg 28 No. of pieces/pallet no. 12 CNG/LPG CODE 0T3D2BWA STRENGTHS: With attention to aesthetics and silence, it continues the tradition of appreciation of the previous "Bluehelix" series Boiler with thick stainless steel primary exchanger, with increased passages (at the top of the category) to guarantee durability and reduced maintenance, it maintains high efficiency even on old systems with oxidation and dirt. A+ System: in combination with the modulating remote control and the external probe (optional) it reaches the upper efficiency class A+ (scale from G to A+++) MC2: Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits MGR: Methane: LPG, Propane air Ready through a simple configuration the boiler is able to operate on methane, LPG and propane air without the use of additional conversion kits Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace Sanitary production in combination with storage tank (optional), standard 3-way valve in the boiler Hydraulic connections covered by the boiler casing Large backlit multifunction graphic display for easy and correct parameter setting Standard by-pass BENEFITS OF BLUEHELIX TECH RRT H: Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard Designed to simplify and facilitate normal maintenance and cleaning operations Minimum polluting emissions (class 6 according to EN 15502-1) Sliding temperature operation via optional external probe Low consumption modulating heating pump (ErP Ready - Class A) Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the aid of the optional antifreeze heater kit Free methane/LPG/propaneted air transformation when checking the product and activating the warranty, to be requested from the Authorized Assistance Center The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION! In case of immediate unavailability, the product will be ordered and shipped within 10 working days Technical Features Model: D2CND024A0AA Heating Efficiency class (55°C): A Firebox power (Qn): 2.9 - 23.5 kW Nominal heating power (80°/60 °C): 2.8 - 22.8 kW Nominal heating power (50°/30°C): 3.1 - 24.0 kW Heating efficiency: Up to 108.7% Modulation range: 1:8 Expansion vessel volume: 8 litres Domestic hot water Efficiency class: A Withdrawal profile: XL Temperature Range: 35°C ~ 60°C Continuous service withdrawal (∆T=30°C): 11.3 l/min Continuous service withdrawal (∆T=25°C): 13.6 l/min Water mains pressure: 0.5~10 Bar Technical data Power supply (V,Hz,Ø) : 220~240/50/1 Power consumption: 3.5 ~ 86 W Water content: 1.31 litres Sound power : 39 dB(A) Sound pressure: 49 dB(A) NOx class : 6 Exhaust gas temperature (G20) : 77° C Electrical protection class: IP X5D Installation data Chimney diameter: 60/100 mm Maximum length for flue gas system DN 60/100: 12.5 m Maximum length for flue gas system DN 80/125: 42.8 m Maximum length for flue gas system DN 80/80: 125 m Dimensions and weight Dimensions (HxLxD): 590x400x256 mm Weight: 27 Kg Simply Peace of Mind Guarantee To guarantee you maximum peace of mind, DAIKIN has designed “SEMPLICEMENTE SERENI”, an extension of the warranty up to the 5th year of life of your product, which includes the subscription to a Scheduled Maintenance Plan with specialized Daikin technicians. Daikin D2C ultra-compact condensing boilers for heating and DHW production Why choose a condensing boiler? Daikin condensing boilers are a good solution for those who want to replace an existing boiler with a more efficient alternative, saving on costs. Our portfolio includes boilers for every need, from the wall-mounted boilers D2C and Full condens and Full Condens TOP, to the boiler with built-in heat storage GCU, to the floor-standing diesel boiler A2 Thanks to the special Daikin patented exchanger, the D2CND boiler achieves high specific power and high partialization to ensure comfort and efficiency in any operating mode and in minimum space. The D2T version, heating only, integrates a diverter valve and can be connected directly to a storage tank for the production of domestic hot water. Ultra-compact and elegant technology The beautiful compact boiler The new D2C condensing boilers are 100% Daikin design. The ultra-compact dimensions make them suitable even for the smallest apartments, where every centimetre saved is space gained A boiler for every need The D2C boilers are available in 3 combi versions 24, 28 and 35 kW for heating and the production of instantaneous domestic hot water. A wide range of heating-only boilers is also available, the D2T, in 5 sizes, from 12 to 35 kW, which can be combined with a storage tank for the production of domestic hot water. They can be installed practically anywhere thanks to their compact size and the minimum installation space required. Thanks to the IPX5D electrical protection rating and the anti-freeze kit, they can also be installed outdoors. Do you want to keep your heating system under control even when you are not at home? Combine the Lan Adapter for control via APP ! Efficiency and respect for the environment The combustion system with regulation via the Gx Lambda probe automatically adapts to the quality of the gas used, methane or LPG, always guaranteeing clean combustion and minimum polluting emissions . Maximum comfort Thanks to a high modulation ratio, up to 1:8 , the power output is automatically varied to always adapt, moment by moment, to the real needs of the home in which it is installed. Endless showers? Domestic hot water will no longer be a problem with the D2C boiler with a DHW flow rate of up to 19 l/min in the 35 kW version Cutting-edge technology meets an attractive and user-friendly user interface Daikin Eye An elegant luminous eye that, thanks to a multi-coloured LED, signals the operating status of the appliance. In the event of a fault, the LED turns red and the error code is displayed. The simplest way to interact with your boiler! Daikin Heating Online Controller Your heating system is always under control, wherever you are! Thanks to the Daikin Heating Online Controller application you can now control and monitor your boiler conveniently from your smartphone in a simple and intuitive way Monitor The state of your heating system The room temperature in your home Energy consumption graphs. Plan Your home temperature and boiler operation with up to 6 actions per day for 7 days Vacation mode Check it out The operating mode and the set room temperature The system and the production of domestic hot water Integrating third-party products and services through IFTTT (if this then that) services Replacing your old boiler has never been easier! Thanks to its small size and IPX5D protection rating, Daikin D2C can be installed virtually anywhere. Its ultra-compact dimensions make it suitable even for the smallest apartments, where every centimeter saved is space gained and its elegant shapes do not look out of place in the kitchen. A distinctive element of the 100% Daikin design is also the Daikin Eye: an elegant luminous eye that, thanks to a multi-chromatic LED, signals the operating status of the appliance. Daikin D2C embodies the best of condensing technology. The SCOT combustion regulation system automatically adapts to the quality of the gas used, methane or LPG, always ensuring clean combustion and minimum polluting emissions. Minimized size and weight are possible thanks to the innovative high-capacity air/fume exchanger body patented by Daikin. The heart of the new D2C boiler, it has been designed to obtain the highest thermal power in the smallest space. Functions Eco Mode Return temperature control to optimize condensation Warm start DHW exchanger already heated and ready for use thanks to the memorization of habits that allows anticipating the request for domestic hot water Solar connection If the water entering the boiler has been preheated by the solar system, the burner does not ignite, for optimal integration of the solar source Exclusive initiative for Daikin customers On the occasion of the launch of the new Daikin D2C, starting from March 1st 2017 Daikin is giving away the activation cost of Semplicemente Sereni. The offer is valid for all those who purchase a Daikin boiler of any type and who already own a Daikin mono split or multisplit. All the details on daikin.it. Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase

Read more less

Hermann Saunier Duval Combitek 28 C gas boiler complete with methane or LPG fume exhaust kit - News PLEASE NOTE! THE BOILER WILL BE SUPPLIED WITH METHANE, THE TRANSFORMATION TO LPG WILL TAKE PLACE THROUGH THE SERVICE CENTER FOR FREE! Select the smoke kit in the drop-down menu! Technical features Model: combitek Power : 28 kW Gas : Methane or LPG Heating efficiency class: A Sanitary efficiency class: A Sanitary load profile XL Maximum pressure at the burner Natural gas G20 (min/max): 2.10/13 mbar Consumption at (min/max) power Natural gas G20: 1.12/2.8 m3/h Maximum pressure at the LPG G30 burner (min/max): 5.3/32.7 mbar Consumption at (min/max) power Natural gas G30: 0.82/2.05 m3/h Dimensions: (HxWxD): 740x410x310 mm; Weight: 34 Kg Connections: gas Ø3/4” heating Ø3/4” sanitary Ø1/2” COMBITEK The optimal solution for heating and domestic hot water preparation . Excellent value for money, both for new builds and replacements It can be retrofitted into existing heating and hot water supply systems The project has been developed to offer the optimal solution in terms of price , performance and quality . Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

AVAILABLE TO ORDER ATTENTION: THE PRODUCT WILL BE SUPPLIED WITHOUT THE SPECIFIC SMOKE KIT! Technical Features Model : Victrix 28 KW TT Boiler Code: 3.025511 Template Code: 2.015543 Type: Snapshot Useful Heating Power: 24 kW Useful Sanitary Power: 28 kW Modulation Range: 11 - 100% Hot water production (∆t 30 °C): 13.4 l/min Dimensions (H x W x D): 748 x 440 x 255 mm Weight: 32.0 Kg VICTRIX 28 KW TT Maximum energy savings, maximum flexibility With VICTRIX 28 kW TT Immergas takes the installation flexibility of condensing boilers even further and offers a wide variety of solutions thanks also to the extreme compactness of its dimensions , just 25 centimetres deep. All boilers can be installed: Inside ; Built-in with OMNI CONTAINER but also in SOLAR CONTAINER or DOMUS CONTAINER to add products that use solar thermal energy and heat pumps to the boiler in the GAUDIUM SOLAR V2 or TRIO V2 applications; Outdoors in partially protected places ; And today also in the open air with the dedicated coverage kit. This increases the possibility of creating systems that comply with the new European Directives, which are increasingly oriented towards condensing technology to reduce pollution and increase energy savings. The eco-friendly VICTRIX kW TT condensing range expresses the best of Immergas technology, offering great performance thanks to the innovations introduced in the product design. Two instantaneous versions of 28 and 35 kW are available, and three heating-only versions (12, 24 and 32 kW PLUS) that can be combined with domestic hot water boiler units of various capacities. HIGH HYDRAULIC PERFORMANCE Primary condensation exchanger, made of an Aluminum-Silicon-Magnesium alloy, particularly resistant to corrosion. Designed to have high flow rate and head performance even on old heating systems thanks to the large water passages. This also means a low risk of clogging in the presence of impurities in the system water. It is important to maintain the pH of the heating system filling water, between 6.5 and 8.5 with a hardness of 15 °F REDUCTION OF ELECTRICITY CONSUMPTION Electricity savings thanks to the low consumption modulating circulator, in class A. The circulator can be set in the operating modes: constant ∆t, proportional prevalence or constant speed . The presence of two NTC probes on the system flow and return allows constant modulation of the boiler operating conditions based on the requests of the heating system with a consequent increase in seasonal efficiency. The boiler's electrical consumption in stand by is less than 6 W DESIGNED TO FACILITATE PROFESSIONALS VICTRIX kW TT, produced on the new highly automated lines at the historic Immergas headquarters in Brescello, is a specific range of products developed on the “Top Tech” platform. It features special technical features designed to facilitate the work of professionals such as: Safety valve discharge piped into condensate drain; Cover casing for hydraulic connections, to better fit the boiler into domestic spaces; Direct accessibility to the electrical connection compartment of the main external devices (e.g. CARV2, external probe, CRONO 7) by simply removing the front aesthetic cover without the need to open the product. SELF-ADAPTING COMBUSTION The electronic gas valve allows air/gas control via a multifunction electrode placed inside the combustion chamber; the electronic board automatically adapts the combustion parameters in the event of variations in air or fuel density. This allows VICTRIX kW TT to be powered by any type of fuel (methane/LPG or propane air), by intervening only on the electronic board software even at a later time (for example when the Authorized Assistance Center starts up for the first time). The boiler is therefore supplied with a single product code . COMFORT High hydraulic performance: the innovative condensing module guarantees high flow rate, low risk of clogging due to impurities in the system water, greater resistance to corrosion thanks to the special alloy. High seasonal efficiencies: the boiler's wide modulation range allows for high seasonal efficiencies with consequent reduction in gas consumption . Thermoregulators: optional. They improve comfort and increase energy savings. DOMINUS App: optional. Simple and intuitive , it allows you to check the boiler operation and temperature, activate its switching on and off from any location via smartphone or tablet. EXTRA Comfort Formula: uses the most complete maintenance program that allows you to extend 5 years with free activation the conventional guarantee which, in collaboration with the Authorized Immergas Assistance Center, can be activated during the initial check. ENVIRONMENTAL COMPATIBILITY Eco-friendly technology: complies with the European ErP and ELD Directives, allows you to achieve high energy efficiency classes in heating and hot water production. Ecological class 5 (European standards UNI 297 and 483): the best for reduced nitrogen oxide emissions (NO X ). Renewable energy: can be combined with solar systems and hybrid systems with heat pumps. INSTALLATION Maximum flexibility: approved for indoor, built-in and outdoor operation, even in the open air . IPX5D electrical protection. Antifreeze as standard up to -5 °C. Maximum compactness: only 25 cm deep. Product Warranty: All products for sale on our site are new and packaged. The warranty on this item is 24 months from the date of purchase

Read more less