ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 006 Product code : 20191951 Optional REC10MH control Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 4.95 Heating COP with water set at 45°C: 3.70 Heating COP with water set at 55°C: 2.95 EER cooling with water set at 7°C: 3.00 EER cooling with water set at 18°C: 4.80 Performance   Heating Useful power in heating with water set at 35° C: 6.35 kW Useful power in heating with water set at 45° C: 6.30 kW Useful power in heating with water set at 55° C: 6.00 kW Absorbed power with water set at 35° C: 1.28 kW Absorbed power with water set at 45° C: 1.70 kW Absorbed power with water set at 55° C: 2.03 kW Cooling down Useful power in cooling with water set at 7 °C: 7.00 kW Useful power in cooling with water set at 18 °C: 6.50 kW Absorbed power with water set at 7° C: 2.33 kW Absorbed power with water set at 18° C: 1.35 kW Technical data Hydronic circuit maximum operating pressure: 3 bar Maximum absorbed power: 0.043 kW System expansion tank: 8 litres Sound data Sound power : 58 dB(A) Sound pressure : 47.5 dB(A) Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1295x792x429 mm Empty weight: 98.0 kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 014 Product code : 20191956 Optional REC10MH command Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 4.60 Heating COP with water set at 45°C: 3.60 Heating COP with water set at 55°C: 2.95 EER cooling with water set at 7°C: 3.61 EER cooling with water set at 18°C: 2.50 Performance   Heating Useful power in heating with water set at 35° C: 14.50 kW Useful power in heating with water set at 45° C: 14.10 kW Useful power in heating with water set at 55° C: 13.80 kW Cooling down Useful power in cooling with water set at 7 °C: 13.50 kW Useful power in cooling with water set at 18 °C: 12.40 kW Sound data Sound power : 65 dB(A) Sound pressure : 53.5 dB(A) Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1385x945x526 mm Empty weight: 144.0 kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 016 Product code : 20191957 Optional REC10MH control Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 4.50 Heating COP with water set at 45°C: 3.50 Heating COP with water set at 55°C: 2.85 EER cooling with water set at 7°C: 3.61 EER cooling with water set at 18°C: 2.50 Performance   Heating Useful power in heating with water set at 35° C: 15.90 kW Useful power in heating with water set at 45° C: 16.00 kW Useful power in heating with water set at 55° C: 16.00 kW Cooling down Useful power in cooling with water set at 7 °C: 14.00 kW Useful power in cooling with water set at 18 °C: 14.20 kW Sound data Sound power : 68 dB(A) Sound pressure : 57.5 dB(A) Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1385x945x526 mm Empty weight: 144.0 kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 016 T Product Code: 20191960 Optional REC10MH control Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 4.50 Heating COP with water set at 45°C: 3.50 Heating COP with water set at 55°C: 2.85 EER cooling with water set at 7°C: 3.61 EER cooling with water set at 18°C: 2.50 Performance   Heating Useful power in heating with water set at 35° C: 15.90 kW Useful power in heating with water set at 45° C: 16.00 kW Useful power in heating with water set at 55° C: 16.00 kW Cooling down Useful power in cooling with water set at 7 °C: 14.00 kW Useful power in cooling with water set at 18 °C: 14.20 kW Sound data Sound power : 68 dB(A) Sound pressure : 58 dB(A) Electrical data Power supply (V,Hz, Ø) : 380~415/50/3 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1385x945x526 mm Empty weight: 160.0 Kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK Certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 008 Product code : 20191952 Optional REC10MH command Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 5.15 Heating COP with water set at 45°C: 3.85 Heating COP with water set at 55°C: 3.18 EER cooling with water set at 7°C: 3.35 EER cooling with water set at 18°C: 5.05 Performance   Heating Useful power in heating with water set at 35° C: 8.40 kW Useful power in heating with water set at 45° C: 8.10 kW Useful power in heating with water set at 55° C: 7.50 kW Absorbed power with water set at 35° C: 1.63 kW Absorbed power with water set at 45° C: 2.10 kW Absorbed power with water set at 55° C: 2.36 kW Cooling down Useful power in cooling with water set at 7 °C: 7.45 kW Useful power in cooling with water set at 18 °C: 8.30 kW Absorbed power with water set at 7° C: 2.22 kW Absorbed power with water set at 18° C: 1.64 kW Technical data Hydronic circuit maximum operating pressure: 3 bar Maximum absorbed power: 0.043 kW System expansion tank: 8 litres Sound data Sound power : 59 dB(A) Sound pressure : 48.5 dB(A) Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1295x945x526 mm Empty weight: 121.0 kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK Certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 004 Product Code: 20191950 Optional REC10MH control Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 5.10 Heating COP with water set at 45°C: 3.80 Heating COP with water set at 55°C: 2.95 EER cooling with water set at 7°C: 3.45 EER cooling with water set at 18°C: 5.50 Performance   Heating Useful power in heating with water set at 35° C: 4.20 kW Useful power in heating with water set at 45° C: 4.30 kW Useful power in heating with water set at 55° C: 4.40 kW Cooling down Useful power in cooling with water set at 7 °C: 4.70 kW Useful power in cooling with water set at 18 °C: 4.50 kW Technical data Sound power : 55 dB(A) Sound pressure : 45 dB(A) Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1295x792x429 mm Empty weight: 98.0 kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION ! IN CASE OF NO IMMEDIATE AVAILABILITY, THE PRODUCT WILL BE ORDERED AND SHIPPED IN 10 WORKING DAYS   FREE FIRST START-UP Technical features Model : HYDRO UNIT M 010 Product code : 20191953 Optional REC10MH control Energy efficiency Energy class in heating at 35° C: A+++ Energy class in heating at 55° C: A++ Heating COP with water set at 35°C: 4.95 Heating COP with water set at 45°C: 3.75 Heating COP with water set at 55°C: 3.10 EER cooling with water set at 7°C: 3.25 EER cooling with water set at 18°C: 4.55 Performance   Heating Useful power in heating with water set at 35° C: 10.00 kW Useful power in heating with water set at 45° C: 10.00 kW Useful power in heating with water set at 55° C: 9.50 kW Absorbed power with water set at 35° C: 2.02 kW Absorbed power with water set at 45° C: 2.67 kW Absorbed power with water set at 55° C: 3.06 kW Cooling down Useful power in cooling with water set at 7 °C: 8.20 kW Useful power in cooling with water set at 18 °C: 9.90 kW Absorbed power with water set at 7° C: 2.52 kW Absorbed power with water set at 18° C: 2.18 kW Technical data Hydronic circuit maximum operating pressure: 3 bar Maximum absorbed power: 0.043 kW System expansion tank: 8 litres Sound data Sound power : 60 dB(A) Sound pressure : 50.5 dB(A) Electrical data Power supply (V,Hz, Ø) : 220~240/50/1 Refrigerant gas : R32 Dimensions and weight Dimensions (LxHxP): 1385x945x526 mm Empty weight: 121.0 kg Beretta HYDRO UNIT M Inverter Monoblock Air-Water Hydronic Heat Pumps These units are used for both heating and cooling applications as well as domestic hot water tanks. They can be combined with fan coil units, underfloor heating applications, low temperature high efficiency radiators, domestic hot water tanks and solar kits, all of which are field powered. A wired controller is supplied with the unit. The backup heater, available as an accessory, can increase the heating capacity in cold outside temperatures. The backup heater also serves as a backup in the event of a malfunction and as a freeze protection of the outdoor water pipes during the winter. Efficiency and sustainability The heat pumps of the HYDRO UNIT M series use R32 as the refrigerant gas, a gas with a lower Global Warming Potential than the traditional gases used. The design of a new sealed circuit for fluorinated gases, the use of R32, reduced load volumes, lower CO2 emissions and increased energy efficiency are the characteristics that differentiate HYDRO UNIT M and increase its sustainability environmental. Quietness The low noise level is guaranteed by the construction features used and can be further reduced thanks to the silent mode programming, available to the customer Antifreeze function The HYDRO UNIT M heat pump is foreseen for outdoor installation and equipped with the ANTIFREEZE function for the protection of the entire hydraulic circuit. This customer-programmable function activates automatically whenever the water temperature in the system drops below a pre-set value, ensuring the protection of the entire system Better performance The ten models available offer powers from 4 kW to 16 kW , with fast response to requests and reduced energy consumption which guarantee energy class A+++ up to 35°C and A++ up to 55°C HP KEYMARK Certified The design meets the requirements of the voluntary European HP KEYMARK certification Easy and flexible Installing HYDRO UNIT M is easy thanks to the hydronic kit that comes with the monobloc and which contains all the essential components. HYDRO UNIT M is flexible thanks to its ability to respond quickly to the real needs of the environments to be served Functional elements Beretta Hydro Unit M Inverter Control Board Maximizes power under critical load conditions and provides stability and efficiency at part loads AISI 316 steel plate heat exchanger : protected with closed cell anti-condensation insulation, it offers high heat exchange efficiency Control board Operating parameters constantly analyzes the ambient temperature and the water temperature to activate the different components and meet the demand Hydronic module Including low consumption circulator, expansion vessel, automatic vent valve and safety valve Electronic expansion valve Optimizes the flow of the refrigerant fluid in every situation Twin rotary compressor Inverter System design including DC twin rotary compressor, fan motor and pump ensures precise motor speed control for the right power needed to perfectly match actual load and save energy Fan Special design of the blade and its edge that allows optimizing the flow surface, improving efficiency and reducing fan noise Heat exchange coil With extended surface and aluminum fins Install more Hydro Unit M HYDRO UNIT M offers the possibility of connecting up to six units to each other for the heating, cooling and domestic hot water needs of small condominiums and light commercial contexts. Each of the units responds individually to the demands of the environment in which it is installed Easily manage the plant Advanced remote control This module, present in every HYDRO UNIT M installation, has a multilingual display and allows you to: Manage up to six units connected in cascade Activate the programmed functions such as the Antifreeze function and the Vacation function, for the serenity of the family REC10MH management module Designed for full-electric and hybrid applications, this module is installed inside the home and allows the user to easily manage the entire system. If the system is equipped with a Hybrid distribution system, REC10MH allows you to manage the multi-zone system to optimize the operation of the system. The module is equipped with a color display and a multilingual menu USB Each HYDRO UNIT M is equipped with a USB port to connect the USB flash memory to update the unit firmware Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Open Chamber Boiler Beretta CIAO LX 24 CAI Low NOx LPG 20151437 - NEW Technical features Model: CIAO LX 24 CAI gpl Code: 20151437 Heating/DHW nominal heat input: 26.70 kW Heating/DHW nominal thermal power: 24.06 kW Efficiency at nominal power: 90.1 Efficiency at reduced load (30%): 89.2% NOx class 6 Maximum working pressure heating bar 3 Maximum absorbed electrical power W 47 Quantity of hot water deltaT 25C° 13.8 l/min Dimensions HxWxD 740x400x340 HELLO LX Beretta has renewed the Ciao open flue boiler; the previous model Ciao S CAI now becomes Ciao LX CAI and is placed in Class NOX 6 . Aesthetically it looks like the previous one but its technology is now completely different. The Ciao LX CAI is the entry-level model for approaching Beretta boiler technology; the CAI model has an open chamber and natural draft. The adjectives that identify it are: high quality standard, sturdiness, reliability and economy in purchasing and running. The innovative Double Exchanger is very compact and is of the plate type with the possibility of preheating . It also uses a low consumption Synchronous Circulator (EEI=0.20) with anti-block cycle system and 3-way valve; it is equipped with a smoke control thermostat and by-pass on the heating circuit. Beretta Ciao has a simple, modern and elegant line; the front panel, the real brain of the boiler, is equipped with many functions. Ciao LX CAI is designed to be installed outdoors in partially protected places, thanks to the dedicated accessories and board antifreeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit together with the siphon antifreeze heater kit (optional to be requested separately from the Beretta Technical Assistance Centre). A convenient liquid crystal digital display for viewing the temperature and diagnostic codes, the on/off/summer/winter/reset/heating temperature/ Amico Climate System selector, the domestic hot water temperature selector/pre-heating activation, the Hydrometer. The wall water fittings, the sanitary taps and the gas tap are not included in the package. GUARANTEED SAVINGS AND HIGH COMFORT Gas consumption is always very low . This new version complies with the new standards on combustion gas emissions (NOx 6) e the ErP Directive 2015 ; the boiler benefits from Energy Classes C in Heating and B in Sanitary . It all starts with savings, starting from the purchase price up to consumption management. Maximum comfort with minimum cost. TECHNICAL FEATURES Class B/C NOx class 6 - ErP version, equipped with 6 m low consumption circulator Double exchanger: primary and sanitary plate with the possibility of preheating 8 liter expansion vessel Arrangement for climatic thermoregulation (optional external probe to be purchased through CAT) IPX5D electrical protection degree Optional plumbing fittings, gas and sanitary taps 3-way valve with anti-block cycle system Smoke control thermostat By-pass on the heating circuit Electronic board with self-diagnostic function and antifreeze protection Simple and intuitive digital display Selector on/off/summer/winter/reset/heating temperature/activation of the Clima Amico system Domestic hot water temperature selector/pre-heating activation Hydrometer Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Beretta MYNUTE X 25 C Low NOx condensing boiler complete with flue gas kit 20163564 Methane - NEW Boiler code 20163564 Seasonal heating energy efficiency class A Energy efficiency class of the sanitary fixture A Declared load profile XL NOx emission class 6 HEATING EXERCISE Heating thermal capacity (max-min) kW 20.00-3.60 Maximum pressure-temperature bar-°C 3 - 90 Expansion tank capacity l 9 HEALTHCARE EXERCISE Nominal DHW heat input (max-min) kW 25.00-3.60 DHW energy efficiency ηwh % 83 DHW production at ∆T= 25°C / 30°C / 35°C l/min 14.3/11.9/10.2 CONNECTIONS Heating inlet - outlet Ø 3/4” DHW inlet - outlet Ø 1/2” Gas inlet Ø 3/4” DIMENSIONS, WEIGHT Boiler dimensions (HxPxL) mm 740x420x275; 35 kgs MYNUTE X BERETTA PRESENTS MYNUTE X, THE NEW RANGE OF CONDENSING BOILERS, WITH MANY INNOVATIVE AND ADVANTAGEOUS FEATURES From the primary exchanger in stainless steel to the modern electronic interface, there are numerous new elements that distinguish MYNUTE X in the Beretta offer. The new condensing range, with its 5 models from 20 to 35 kW, with "combined" and "heating only" versions, meets every need for residential comfort. High efficiency, low consumption and ease of installation make MYNUTE X the winning choice, both for new homes and for the replacement market. With MYNUTE X, the novelty of the project merges with Beretta's tradition of excellence, matured in almost half a century of experience in the home comfort sector. Its aesthetics, in line with the Beretta style of the latest generation products, easily integrates into any living context, thanks also to its compactness and installation flexibility. NEW DIGITAL INTERFACE MYNUTE X is equipped with a modern and user-friendly control panel, elegantly covered by a door that lets you glimpse the light of its "green gem", the LED light bar that signals its current operating status. Through a modern backlit LCD display, which communicates with the user through icons and scrolling texts (multilingual), it is possible to access the functions of MYNUTE X. Through 7 silk-screened operating keys, it is possible to navigate the panel in a simple and intuitive way, accessing to the settings and parameterizations of the boiler and the system. MYNUTE X FEATURES MANAGEMENT OF UP TO 2 HYDRAULIC CIRCUITS, HIGH AND/OR LOW TEMPERATURE, THROUGH SPECIFIC PREHEATING ACCESSORIES PREHEATING ACTIVATION TO REDUCE DOMESTIC HOT WATER WAITING TIMES CLOCK FUNCTION WEEKLY PROGRAMMING INTEGRATED IN THE DISPLAY POSSIBILITY OF CONNECTION WITH DOMESTIC HOT WATER TANK (R MODELS) Technology and benefits NEW PRIMARY EXCHANGER IN STAINLESS STEEL THE NEW MYNUTE X EXCHANGER IS MADE OF STAINLESS STEEL, WITH A HIGH SECTION SMOOTH PIPE TO OFFER THE BEST EFFICIENCY AND CLEANLINESS OVER TIME. In addition to the high resistance to the corrosive action of acid condensate, AISI 304 L stainless steel reduces the internal formation of oxides and other electrochemical phenomena typical of installation on old systems. The single wound coil geometry (hydraulic circuit in series) offers a constant flow rate in all sections of the exchanger and intrinsically limits clogging phenomena. Front access facilitates periodic maintenance and cleaning of the combustion chamber. INTEGRATED CLAP MYNUTE X is C10 * approved (formerly 3CEp approved), integrating the non-return valve (clapet) as standard on all models, which makes it "ready to install" in case of installations in pressurized collective flues, for which the non-return valve is a mandatory device. The non-return valve is a specific device which allows the combustion fumes to flow through the ducts in only one direction, i.e. from the burner to the flue gas outlet. Its function is therefore to prevent the fumes from returning to the combustion chamber, compromising the correct functioning of the boiler. This could happen for various reasons, for example in the event of overpressure in the duct of a collective flue system. The non-return valve is generally supplied as a specific optional kit, to be installed at the flue outlet of a boiler in the case of C10 type collective exhausts. In MYNUTE X the non-return valve is positioned inside the boiler (see detail), which translates into quick installation and cost reduction. HYBRID READY MYNUTE X is a HYBRID READY solution. The boiler was born within the offer of HYBRID READY products, which make up the new hybrid technology system conceived and developed in the Beretta Research Laboratories. This system, created to meet the current and future integration and management needs of the various energy sources (Gas/Electricity/Renewables), also includes the most innovative methods of energy accumulation and distribution. Characteristics INNOVATIVE STAINLESS STEEL CONDENSING HEAT EXCHANGER WITH FRONT ACCESS WIDE MODULATION RANGE (UP TO 1:8) LOW CONSUMPTION MODULATING CIRCULATOR (EEI ≤ 0.20), 6 m EQUIPPED WITH STANDARD FUME CLAP (CHECK VALVE) AND C(10) APPROVED.* LOW POLLUTANT EMISSIONS: CLASS 6 (UNI EN 15502) MYNUTE X IS HYBRID READY: IT WAS BORN TO BE INTEGRATED INTO BERETTA MULTI-ENERGY SYSTEMS THROUGH THE HYBRID REC 10H AND THE HYBRID CONNECTS, AVAILABLE AS ACCESSORIES INSTALLATION FLEXIBILITY: INDOOR, OUTDOOR** AND RECESSED*** INSTALLATION (IN A PARTIALLY PROTECTED PLACE) CLICK-FIT FLUE CONNECTION: FAST AND SAFE, WITHOUT THE NEED OF AN EXTERNAL COLLAR ANTIFREEZE RESISTANCE KIT, HYDRAULIC CONNECTIONS AND EXTERNAL PROBE AVAILABLE AS ACCESSORIES ELECTRICAL PROTECTION DEGREE IPX5D SUPPLIED "DOUBLE T" TEMPLATE COMPATIBLE WITH HYBRID CONNECTORS FOR THE MANAGEMENT OF UP TO TWO SYSTEM ZONES FOR GAS CONVERTING, PLEASE CONTACT AUTHORIZED BERETTA TECHNICAL ASSISTANCE CENTERS COMPATIBLE WITH BeSMART WIFI COMFORT CONTROL AS THERMOSTAT (OTBUS COMMUNICATION), ALLOWING THE MOST ADVANCED FUNCTIONS POSSIBILITY OF INTUBATING FLUES WITH THE SPECIFIC FLUE IN PP Ø60 AND Ø50 Product Warranty The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Characteristics: Class A heating energy efficiency Sanitary energy efficiency Class A Sanitary load profile: XL Heating / domestic hot water nominal heat input kW 20/28 Heating / domestic hot water reduced heat input kW 2.80 Supply voltage/frequency: 230/50 Volt/Hz NOx Class 5 Supply voltage / frequency Volt/Hz 230/50 Boiler dimensions (HxLxP) mm 780x400x365; 36 Gas version available: METHANE Warm-up exercise: Maximum pressure and temperatures bar / °C 3 / 90 Expansion vessel capacity 9 litres Healthcare exercise: Minimum / maximum pressure 0.2 - 6 bar Quantity of hot water with Δt =25° litres/min 16.1 Minimum domestic water flow rate litres/min 2 To view further technical information on the product CLICK HERE The new MySMART condensing boiler is designed following the ecodesign indications provided for by the European ErP Directive. MySMART has a higher power in DHW mode thus offering greater comfort. The boiler, an instantaneous combined model, offers as standard the new front access condensing exchanger with improved efficiency (94% seasonal efficiency) and the low consumption FLEX modulating circulator with modifiable head up to 7m. MySMART is compatible with the new Ø 50 mm flue with which it is possible to carry out ducting up to 7m. The BeSMART Comfort Control is inserted as standard with MySMART with the WiFi Box, the external probe, the flue splitter, the plumbing fittings cover, the template, the heating taps with filter, the brass plumbing fittings, the gas taps and sanitary. It forms a class A + system without the addition of options BeSMART WiFi Comfort control included as standard Available APPs for management from Smartphone and Tablet Very high modulation (up to 1:10) Flex low consumption circulator (EEI ≤ 0.20 ) with 6m head adjustable to 7m Possibility of ducting with the special flue in PP Ø 50 Standard ø 80 mm splitter General characteristics BeSMART the advanced comfort control Leaving for your home in the mountains? Or returning from a business trip? Through your Smartphone or Tablet, with the BeSMART App you can turn the boiler on and off, read the home and outside temperature and change the time programming of your heating system. The BeSMART WiFi Comfort Control Panel, standard in the MySMART boiler, is the remote boiler management device with chronothermostat functions. With the WiFi Box kit (series) it is possible to manage comfort even remotely with a Smartphone and Tablet. Simple and intuitive, it allows you to adjust the parameters and activate the many functions on the boiler. A large liquid crystal display shows all important information. Using the keys, the temperature of the heating water and domestic hot water is set easily and intuitively and the time programming is carried out. MySMART also features the Easy Climate function (thermoregulation with standard external probe). MySMART, the elegant The new MySMART boiler is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to easily select all the functions necessary for using and setting the boiler. OTHER CHARACTERISTICS: Telemanagement : Remotely, with BeSMART, you can turn the boiler on and off, change the temperatures, program the weekly chronothermostat, view the home temperature. Management with tablets and smartphones : Compatible with smartphones and tablets using the Android (≥ 3.0 ver.) or iOS system. Downloadable Apps: Available APPs compatible with Android (≥ ver. 3.0) and iOS systems for switching on/off and managing boilers/systems remotely via Smartphone and Tablet. WiFi : WiFi communication between the WiFi Box and the home ADSL WiFi modem router to connect to the internet. Possibility to connect to the optional WiFi modem kit for SIM CARD as an alternative to the ADSL modem. RF : RF (radio frequency) communication between the BeSMART Comfort Control and the WiFi Box; Possibility of connecting up to 8 BeSMART Comfort Controls in RF to manage up to 8 different zones/environments (wireless communication up to 40 m away). Weekly heating time programming : Heating time programming in 30 minute intervals and possibility to choose between different pre-set programs. Holiday function: For quick entry of the number of holiday days in which to operate the generator in order to have a reduced room temperature. The acronym ErP, an acronym for "Energy related Products", identifies Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015, the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class. Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility of easily identifying the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual devices. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with a nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Beretta's commitment is concrete and is directed towards an increasingly eco-sustainable future. This is why Beretta is already ErP-Ready today with solutions for any installation and comfort requirement linked to autonomous residential and centralized systems. A complete and constantly evolving catalog with many ErP-Ready proposals in the case of mere replacement, energy redevelopment, renovation or new construction. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

BUILT-IN BOX FOR BERETTA BOILERS

Read more less

Beretta MYNUTE X 35C Low NOx condensing boiler complete with flue gas kit 20163566 Methane - NEW Boiler code 20163566 Seasonal heating energy efficiency class A Energy efficiency class of the sanitary fixture A Declared load profile XL NOx emission class 6 HEATING EXERCISE Heating thermal capacity (max-min) kW 30.00-4.90 Maximum pressure-temperature bar-°C 3 - 90 Expansion tank capacity l 9 HEALTHCARE EXERCISE Nominal DHW heat input (max-min) kW 34.60-4.90 DHW energy efficiency ηwh % 85 DHW production at ∆T= 25°C / 30°C / 35°C l/min 19.8/16.5/14.2 CONNECTIONS Heating inlet - outlet Ø 3/4” DHW inlet - outlet Ø 1/2” Gas inlet Ø 3/4” DIMENSIONS, WEIGHT Boiler dimensions (HxPxL) mm 740x420x275; 37 kgs MYNUTE X BERETTA PRESENTS MYNUTE X, THE NEW RANGE OF CONDENSING BOILERS, WITH MANY INNOVATIVE AND ADVANTAGEOUS FEATURES From the primary exchanger in stainless steel to the modern electronic interface, there are numerous new elements that distinguish MYNUTE X in the Beretta offer. The new condensing range, with its 5 models from 20 to 35 kW, with "combined" and "heating only" versions, meets every need for residential comfort. High efficiency, low consumption and ease of installation make MYNUTE X the winning choice, both for new homes and for the replacement market. With MYNUTE X, the novelty of the project merges with Beretta's tradition of excellence, matured in almost half a century of experience in the home comfort sector. Its aesthetics, in line with the Beretta style of the latest generation products, easily integrates into any living context, thanks also to its compactness and installation flexibility. NEW DIGITAL INTERFACE MYNUTE X is equipped with a modern and user-friendly control panel, elegantly covered by a door that lets you glimpse the light of its "green gem", the LED light bar that signals its current operating status. Through a modern backlit LCD display, which communicates with the user through icons and scrolling texts (multilingual), it is possible to access the functions of MYNUTE X. Through 7 silk-screened operating keys, it is possible to navigate the panel in a simple and intuitive way, accessing to the settings and parameterizations of the boiler and the system. MYNUTE X FEATURES MANAGEMENT OF UP TO 2 HYDRAULIC CIRCUITS, HIGH AND/OR LOW TEMPERATURE, THROUGH SPECIFIC PREHEATING ACCESSORIES PREHEATING ACTIVATION TO REDUCE DOMESTIC HOT WATER WAITING TIMES CLOCK FUNCTION WEEKLY PROGRAMMING INTEGRATED IN THE DISPLAY POSSIBILITY OF CONNECTION WITH DOMESTIC HOT WATER TANK (R MODELS) Technology and benefits NEW PRIMARY EXCHANGER IN STAINLESS STEEL THE NEW MYNUTE X EXCHANGER IS MADE OF STAINLESS STEEL, WITH A HIGH SECTION SMOOTH PIPE TO OFFER THE BEST EFFICIENCY AND CLEANLINESS OVER TIME. In addition to the high resistance to the corrosive action of acid condensate, AISI 304 L stainless steel reduces the internal formation of oxides and other electrochemical phenomena typical of installation on old systems. The single wound coil geometry (hydraulic circuit in series) offers a constant flow rate in all sections of the exchanger and intrinsically limits clogging phenomena. Front access facilitates periodic maintenance and cleaning of the combustion chamber. INTEGRATED CLAP MYNUTE X is C10 * approved (formerly 3CEp approved), integrating the non-return valve (clapet) as standard on all models, which makes it "ready to install" in case of installations in pressurized collective flues, for which the non-return valve is a mandatory device. The non-return valve is a specific device which allows the combustion fumes to flow through the ducts in only one direction, i.e. from the burner to the flue gas outlet. Its function is therefore to prevent the fumes from returning to the combustion chamber, compromising the correct functioning of the boiler. This could happen for various reasons, for example in the event of overpressure in the duct of a collective flue system. The non-return valve is generally supplied as a specific optional kit, to be installed at the flue outlet of a boiler in the case of C10 type collective exhausts. In MYNUTE X the non-return valve is positioned inside the boiler (see detail), which translates into quick installation and cost reduction. HYBRID READY MYNUTE X is a HYBRID READY solution. The boiler was born within the offer of HYBRID READY products, which make up the new hybrid technology system conceived and developed in the Beretta Research Laboratories. This system, created to meet the current and future integration and management needs of the various energy sources (Gas/Electricity/Renewables), also includes the most innovative methods of energy accumulation and distribution. Characteristics INNOVATIVE STAINLESS STEEL CONDENSING EXCHANGER WITH FRONT ACCESS WIDE MODULATION RANGE (UP TO 1:8) LOW CONSUMPTION MODULATING CIRCULATOR (EEI ≤ 0.20), 6 m EQUIPPED WITH STANDARD FUME CLAP (CHECK VALVE) AND C(10) APPROVED.* LOW POLLUTANT EMISSIONS: CLASS 6 (UNI EN 15502) MYNUTE X IS HYBRID READY: IT WAS BORN TO BE INTEGRATED IN BERETTA MULTI-ENERGY SYSTEMS THROUGH THE HYBRID REC 10H AND THE HYBRID CONNECTS, AVAILABLE AS ACCESSORIES INSTALLATION FLEXIBILITY: INDOOR, OUTDOOR** AND RECESSED*** INSTALLATION (IN A PARTIALLY PROTECTED PLACE) CLICK-FIT FLUE CONNECTION: FAST AND SAFE, WITHOUT THE NEED OF AN EXTERNAL COLLAR ANTIFREEZE RESISTANCE KIT, HYDRAULIC CONNECTIONS AND EXTERNAL PROBE AVAILABLE AS ACCESSORIES ELECTRICAL PROTECTION DEGREE IPX5D SUPPLIED "DOUBLE T" TEMPLATE COMPATIBLE WITH HYBRID CONNECTORS FOR THE MANAGEMENT OF UP TO TWO SYSTEM ZONES FOR GAS CONVERTING, PLEASE CONTACT AUTHORIZED BERETTA TECHNICAL ASSISTANCE CENTERS COMPATIBLE WITH BeSMART WIFI COMFORT CONTROL AS THERMOSTAT (OTBUS COMMUNICATION), ALLOWING THE MOST ADVANCED FUNCTIONS POSSIBILITY OF INTUBATING FLUES WITH THE SPECIFIC FLUE IN PP Ø60 AND Ø50 Product Warranty The warranty on this item is 24 months from the date of purchase.

Read more less