Technical features Heating nominal heat input: 30 kW Heating nominal heat output: 29.13 kW Classification European Directive EEC 92/42: ★ ★ ★ ★ Sanitary comfort ★ ★ ★ Expansion vessel capacity: 10 l Quantity of hot water with Δt=25°C: 17.2 l/min Minimum domestic water flow rate: 2 l/min Sanitary water temperature selection range: 35 - 60°C Total electric power: 125W Electrical protection degree: IP X5D NOx emission class: 5 Power supply: methane Characteristics Modulation 1:10 Low consumption modulating circulator (Class A) Patented condensing exchanger (Patent Pending) in aluminum with high flow rate Thermoregulation with standard external probe Standard hydraulic fitting cover For gas conversion, contact authorized Beretta Technical Assistance Centres Dimensions Dimensions (HxWxD): 845x453x358 mm Weight: 42Kg

Read more less

Technical features Energy label specifications according to the European ErP directive   Sanitary Energy Efficiency : Class A Load profile: L Exercise features: Open chamber with natural draft Ignition - 1.5 battery Flame control - by ionization Nominal heat output: 24 kW Hot water production Δ T=25°C: 14 l/min Min/max pressure bar 0.3/10 Ø water and gas connections - 1/2” Dimensions (HxLxP): mm 620x380x224; 11.5 kgs The guarantee is the Official Beretta Italia one, and has a duration of 24 months Power supply: LPG General characteristics SOURCE 2 DGT Fonte 2 DGT, hot water in compact dimensions From Beretta's experience and technological research comes the new line of Fonte 2 DGT water heaters, designed to offer maximum sanitary comfort, maximum energy savings and greater simplicity of use. Thanks to its extremely compact dimensions, Fonte 2 DGT can also be placed in limited spaces and therefore represents the ideal solution to meet the installation needs of modern living contexts. The range, open ionization chamber with battery ignition, two water filters as standard and with codes for both methane and LPG, is made up of the Fonte 2 DGT versions with 11 and 14 litres/min models and Fonte 2 DGT FLEX with a from 11 litres/min. The FLEX versions also include the hoses and the sanitary tap. Source 2 DGT: high energy class and low consumption The Fonte 2 DGT line of water heaters is equipped with the special device known as the Economiser, specifically designed to combine maximum user comfort with significant energy and cost savings. The activation of the Economizer in fact allows to reduce gas consumption up to over 50%, limiting the maximum thermal power supplied, when the usage requirements are contained (low temperature difference or reduced sampling flow rates, such as for example during summertime). Furthermore, on all Fonte 2 DGT models, the Economizer can be adjusted progressively by the user, according to needs, achieving maximum savings in the low flame position. Finally, the appliances in the Fonte 2 DGT range are equipped with flame modulation which, by adapting gas consumption to individual withdrawal requests, allows the temperature of the water supplied to be kept almost constant, compatibly with the settings made and the power of the water heater. The Beretta Fonte 2 DGT water heater guarantees always very low gas consumption and respect for the environment. Beretta Fonte 2 DGT complies with the current ERP regulation placing itself in CLASS A for energy consumption. Functionality and ease of use The Fonte 2 DGT water heaters, with a linear and essential design, have an ergonomic dashboard which houses two knobs which allow you to manage all the functions of the appliance in a simple and intuitive way and a display which shows the temperature of the domestic hot water produced. The left knob, in addition to the on/off functions, activates the "Gas economiser" device, adjustable between the small flame and the large flame, allowing the user to make an interesting gas saving. The right knob allows you to set the temperature of the water supplied, by regulating the quantity of water at the outlet Characteristics: Instantaneous open chamber water heater with Natural Gas and LPG versions Abundant production of domestic hot water: 11 or 14 litres/min Digital display with indication of domestic hot water temperature Battery ignition and ionisation flame presence control Gas economizer with 8 regulation steps Modulating flame regulation system Simple and intuitive control panel Compact size and simple installation without removing the shell Assembly template supplied (gasket and hose holder for LPG versions) New easy access water connections on the same horizontal axis New latest generation water/gas group with integrated gas pressure regulator Double inlet water filter Safety microswitch to protect the batteries (2 x 1.5 Volt type D) in the OFF position Temperature selector FLEX versions with flexible fittings and standard tap Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

NB: in the absence of this product, the new model CIAO S 24 CAI LX LOW NOX will be shipped GAS BOILER BERETTA CIAO S 24 CAI LPG OPEN CHAMBER - NEW ErP Technical features Model: HELLO S 24 CAI Code: 20096549 Heating/DHW nominal heat output: 24 kW Efficiency at nominal power: 92% Efficiency at reduced load (30%): 90.6% Quantity of hot water with Δt=25°C: 14 l/min Dimensions (hxwxd) mm 740 x 400 x 340; 30kg Heating and DHW energy efficiency class (ErP): C - B LPG power supply Legend: C (heating + sanitary water), A (Open Room) I (electronic ignition, ionisation control). HELLO S, the reliable one Innovation at the service of quality The new Ciao S, available in both the open chamber and sealed chamber versions with a thermal power of 24kW, is designed with components that belong to a high quality standard: a boiler which is therefore characterized by reliability and sturdiness. The models in the Ciao S range are compliant with Legislative Decree 311/06 HELLO S, the universal A sealed boiler for all environments The sealed chamber models are designed to be installed outdoors in partially protected places or recessed thanks to the dedicated accessories and board anti-freeze protection down to -3°C. In colder temperature conditions it is possible to extend the protection down to -10°C using the antifreeze heater kit (optional) together with the lower cover (optional). The upper cover is also available for greater protection of the appliance. The new Ciao S range also benefits from the high degree of electrical protection IPX5D. HELLO S, the elegant A modern style The new Ciao S is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to perform all the functions necessary for using the boiler. Characteristics: CAI boilers, ErP version, equipped with 6 m low consumption circulator (EEI0.20) Can also be installed externally and recessed (model CSI only) Double exchanger: primary and sanitary Double air intake (mod. CSI) Can be installed flush-mounted using special optional accessories (mod. CSI) 8 liter expansion vessel Three-speed circulator with 5 m (non ErP versions) Simple and intuitive digital display Arrangement for climatic thermoregulation (optional external probe) Can be interfaced with the REC 08 Remote Control Panel (optional) IPX5D electrical protection degree Available lower cover for mod. CIS (optional) Optional plumbing fittings, gas and sanitary taps Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. FOR CONVERSION TO LPG, CONTACT YOUR LOCAL AUTHORIZED ASSISTANCE CENTER IN ADVANCE Beretta MYNUTE X 30C Low NOx condensing boiler complete with flue gas exhaust kit 20163565 LPG - NEW Boiler code 20163565 Seasonal heating energy efficiency class A Sanitary ware energy efficiency class A Declared load profile XL NOx emission class 6 WARM-UP EXERCISE Heating thermal capacity (max-min) kW 25.00-4.90 Maximum pressure-temperature bar-°C 3 - 90 Membrane expansion vessel capacity 9 l HEALTH EXERCISE Nominal ACS heat output (max-min) kW 30.00-4.90 ACS energy efficiency ηwh % 85 DHW production at ∆T= 25°C / 30°C / 35°C l/min 17.2/14.3/12.3 LINKS Heating inlet - outlet Ø 3/4” Sanitary inlet - outlet Ø 1/2” Gas inlet Ø 3/4” DIMENSIONS, WEIGHT Boiler dimensions (HxDxL) mm 740x420x275; 35 Kg MYNUTE X BERETTA PRESENTS MYNUTE X, THE NEW RANGE OF CONDENSING BOILERS, WITH MANY INNOVATIVE AND ADVANTAGEOUS FEATURES From the stainless steel primary exchanger to the modern electronic interface, there are numerous new elements that distinguish MYNUTE X in the Beretta offer. The new condensing range, with its 5 models from 20 to 35 kW, with “combined” and “heating only” versions, meets every need for residential comfort. High efficiency, low consumption and ease of installation make MYNUTE X the winning choice, both for new homes and for the replacement market. With MYNUTE X, the novelty of the project merges with the tradition of excellence of Beretta, matured in almost half a century of experience in the domestic comfort sector. Its aesthetics, in line with the Beretta style of the latest generation products, easily integrates into any living context, thanks also to its compactness and installation flexibility. NEW DIGITAL INTERFACE MYNUTE X is equipped with a modern and user-friendly control panel, elegantly covered by a door that allows you to glimpse the light of its “green gem”, the LED light bar that indicates its current operating status. Through a modern backlit LCD display, which communicates with the user through icons and scrolling texts (multilingual), it is possible to access the functions of MYNUTE X. Through 7 silk-screened operating keys, it is possible to navigate the panel in a simple and intuitive way, accessing the settings and parameterizations of the boiler and the system. MYNUTE X FUNCTIONS MANAGEMENT OF UP TO 2 HYDRAULIC CIRCUITS, HIGH AND/OR LOW TEMPERATURE, THROUGH SPECIFIC PREHEATING ACCESSORIES PREHEATING ACTIVATION TO REDUCE WAITING TIMES FOR HOT WATER CLOCK FUNCTION WEEKLY PROGRAMMING INTEGRATED IN THE DISPLAY POSSIBILITY OF CONNECTION WITH HOT WATER BOILER (R MODELS) Technology and advantages NEW STAINLESS STEEL PRIMARY EXCHANGER THE NEW MYNUTE X EXCHANGER IS MADE OF STAINLESS STEEL, WITH A SMOOTH PIPE WITH A HIGH SECTION TO OFFER THE BEST EFFICIENCY AND CLEANLINESS OVER TIME. AISI 304 L stainless steel, in addition to its high resistance to the corrosive action of acid condensation, reduces the internal formation of oxides and other electrochemical phenomena typical in installations on old systems. The single wound coil geometry (hydraulic circuit in series) offers a constant flow rate in all sections of the exchanger and intrinsically limits clogging phenomena. Front access facilitates periodic maintenance and cleaning operations of the combustion chamber. INTEGRATED CLAPET MYNUTE X is C10 approved * (formerly 3CEp approved), integrating the non-return valve (clapet) as standard on all models, making it “ready to install” in the case of installations in pressurized collective flues, for which the non-return valve is a mandatory device. The non-return valve is a specific device that allows combustion fumes to flow through the ducts in one direction only, i.e. from the burner to the flue outlet. Its function is therefore to prevent the fumes from returning to the combustion chamber, compromising the correct functioning of the boiler. This eventuality could occur for various reasons, for example in the case of overpressure in the duct of a collective flue system. The non-return valve is generally supplied as a specific optional kit, to be installed at the flue outlet of a boiler in the case of C10 type collective flues. In MYNUTE X the non-return valve is positioned inside the boiler (see detail), which translates into quick installation and reduced costs. HYBRID READY MYNUTE X is a HYBRID READY solution. The boiler is part of the HYBRID READY product range, which constitutes the new hybrid technology system conceived and developed in the Beretta Research Laboratories. This system, created to meet current and future needs for the integration and management of different energy sources (Gas/Electricity/Renewables), also includes the most innovative methods of energy storage and distribution. Characteristics INNOVATIVE STAINLESS STEEL CONDENSING EXCHANGER WITH FRONT ACCESS WIDE MODULATION RANGE (UP TO 1:8) LOW CONSUMPTION MODULATING CIRCULATOR (EEI ≤ 0.20), 6 m EQUIPPED WITH STANDARD SMOKE CLAPE (NON-RETURN VALVE) AND C(10) APPROVED.* LOW POLLUTING EMISSIONS: CLASS 6 (UNI EN 15502) MYNUTE X IS HYBRID READY: IT IS DESIGNED TO BE INTEGRATED INTO BERETTA MULTI-ENERGY SYSTEMS THROUGH THE REC 10H HYBRID AND THE CONNECT HYBRID, AVAILABLE AS ACCESSORIES INSTALLATION FLEXIBILITY: INDOOR, OUTDOOR** AND BUILT-IN INSTALLATION*** (IN A PARTIALLY PROTECTED PLACE) CLICK-FIT FLUE CONNECTION: FAST AND SAFE, WITHOUT THE NEED FOR AN EXTERNAL COLLAR ANTIFREEZE RESISTANCE KIT, HYDRAULIC CONNECTIONS AND EXTERNAL PROBE AVAILABLE AS ACCESSORIES ELECTRICAL PROTECTION DEGREE IPX5D “DOUBLE T” TEMPLATE SUPPLIED, COMPATIBLE WITH HYBRID CONNECTS FOR MANAGING UP TO TWO SYSTEM AREAS FOR GAS CONVERSION CONTACT THE AUTHORISED BERETTA TECHNICAL ASSISTANCE CENTERS COMPATIBLE WITH BeSMART WIFI COMFORT CONTROL AS A THERMOSTAT (OTBUS COMMUNICATION), ALLOWING THE MOST ADVANCED FUNCTIONS POSSIBILITY OF PIPETING FLUES WITH THE SPECIFIC PP FLUE PIPE Ø60 AND Ø50 Product Warranty The warranty on this item is 24 months from the date of purchase.

Read more less

GAS BOILER BERETTA METEO 24 CAI AG METHANE OPEN CHAMBER -NEW ErP Technical features Product code: 20101258 Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary energy efficiency profile XL Class B Characteristics of heating/DHW operation: Heating/DHW nominal heat output: 24 kW Quantity of hot water with Δt=25°C: 14 l/min Dimensions (hxwxd) mm 760 x 494 x 240 METHANE power supply Legend: C (heating + sanitary water), A (Open Room) I (electronic ignition, ionisation control). AG Antifreeze as standard down to -15°C WEATHER - ErP Meteo is a complete range of specific boilers for outdoors. The high technological content enhances the specific characteristics to the maximum: dimensions, standard remote control panel, resistance to external agents, innovative performance. The quality of the materials and the innovative design of the shell add elegance to these very small and high performance boilers. Extremely reliable and simple to use, the Meteo range boilers were created specifically for outdoor installations. The unique shell structure, IPX4D electrical protection and materials used for the shell provide maximum protection from external agents. The streamlined, modern aesthetic allows water to roll off. The installation is facilitated by reduced dimensions and supplied equipment. Designed for installations on balconies, Meteo, with a depth of only 24 cm, is the ideal answer to space problems; it is equipped as standard with fittings for connection to the system, gas and sanitary taps and a positioning template. The remote control panel, supplied as standard, allows total control of the boiler from inside the home. The main functions are simple and immediate, with many other user-customizable settings. The remote control panel also functions as a chronothermostat weekly and is set up for climate control via an external probe (optional). Characteristics: CAI boilers, ErP version, equipped with low consumption circulator (EEI0.20) modifiable up to 7m head MIX combustion (Air/Gas): constant efficiency (mod. CSI) Built with specific materials for outdoor use REC 05 remote control panel as standard ø 60 fume exhaust adapter with standard air intake (mod. CSI) Standard antifreeze up to -15 °C IPX4D electrical protection degree Arrangement for climatic thermoregulation Plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee The warranty on this item is 24 months from the date of purchase.

Read more less

Technical features Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Heating nominal heat input: 25 kW Sanitary nominal heat input: 30 kW Classification European Directive EEC 92/42: **** Quantity of hot water with Δt=25°C: 17 l/min IPX5D electrical protection degree Nox class: 5 Power supply: methane Characteristics The new Beretta boiler is made up of a new type of front access exchanger, made up of a single seamless aluminum tube, thus making the thermal resistance of aluminum higher than steel, allowing for uniform temperature distribution. In addition, this accurate serial circuit allows a large part to be prepared for the passage of water, reducing pressure drops and preventing the deposit of impurities, thus allowing excellent performance over time. In addition, with MYNUTE, it is equipped with a 50mm smoke outlet approval. For periodic cleaning, the boiler has an accurate system of guides which facilitates the assembly and disassembly of the drawer. Finally, for the management of the device there are two knobs, one for regulating the temperature and the other for domestic hot water, and a display that shows all the functions which is very simple to use. For filling the system, it has a filling cock and a visible filling hydrometer. FLEX modulating circulators: The MYNUTE RAIN boiler works with an electric motor of the circulator with an Energy Efficiency of 0.20, also having such a significant energy savings compared to traditional boilers. It is also possible to modify, if greater heating is required, the head of the circulator with a larger one (FLEX). Dimensions: (HxWxD): 797x553x274mm

Read more less

NB: PRODUCT DISCONTINUED --> THE NEW MODEL EXCLUSIVE GREEN E 25 WILL BE SHIPPED Beretta EXCLUSIVE GREEN HE 25 boiler Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating nominal heat input: 20 kW Heating nominal heat output: 21.44 kW Classification European Directive EEC 92/42: ★ ★ ★ ★ Sanitary comfort ★ ★ ★ (EN 13203) NOx emission class: 5 (UNI EN 677) Efficiency at rated power: 98.7% Efficiency at reduced load (30%): 109.6% Total electric power: 93W Electrical protection degree: iP X5D Expansion tank capacity: 9 lt Quantity of hot water with Δt=25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min Sanitary water temperature selection range: 35 - 60°C Dimensions (hxlxp) mm 845x453x358 ; 44kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control). EXCLUSIVE GREEN HE HI-EFFICIENCY ECOLOGICAL CONDENSING WALL-MOUNTS The new Exclusive Green E condensing boilers, equipped with the innovative Beretta front exchanger, in addition to implementing the requests of the ErP standards, improve all the peculiarities confirming themselves as top of the range. Seasonal efficiency up to 94%, very wide modulation range (up to 1:10), low consumption modulating circulator with the possibility of increasing the head up to 7m and reduced consumption are some of the main features. The new Exclusive Green E boilers also offer excellent reliability and technology and, thanks to their high performance, are an excellent solution in hybrid systems with solar thermal and heat pumps. The external probe that allows you to activate the climatic thermoregulation is standard as standard. Furthermore, by adding the optional BeSMART WiFi Comfort Control kit and the LINK MODE interface board kit, Exclusive Green E constitutes a class A+ system and home comfort can be governed by remotely via APP for smartphones and tablets. The boilers are equipped with a special high-head fan designed to be able to pipe flues with Ø 60 mm or Ø 50 mm flues. Front access condensing heat exchanger ( New ! ) The Exclusive Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. Modulation 1:10 The range offers a wide range of modulation to respond to real energy needs, while simultaneously offering a high reduction in consumption. Beretta realizes this system through a totally pneumatic and therefore safe and reliable model. The electronics in fact act only on the number of fan revolutions (inlet air flow rate) without intervening on the injection of the gas quantity which is automatically sucked in. Beretta therefore introduces a new double distribution mixer: a mechanical damper with a calibrated weight which opens or closes a part of the section of the venturi so as to divide the modulation range into two stages (smaller section with low air flow rates or larger section with high air flow rates). Beretta has also developed a specific silencer in the air intake to reduce any resonances generated by the new mixer. Warranty All products for sale on our site are new and packed. The guarantee yes

Read more less

BERETTA CIAO AT 25 CSI CONDENSING BOILER COMPLETE WITH LPG FUME EXHAUST KIT - NEW ErP Product code: 20113788 Characteristics: Energy efficiency in heating: B Energy efficiency Sanitary: A Sanitary load profile: XL Nominal heat input: 25 kW Electric Power: 129W Supply voltage/frequency: 230/50 Volt/Hz Electrical protection degree: X5D ip Dimensions HxWxD: 780 x 400 x 338 ; 40 Kg Gas version available: METHANE Warm-up exercise: Maximum pressure and temperatures: 3/90 bar/°C Heating temperature selection range: 40/80 °C Pump: pump head available for the system: 266 m/bar Expansion tank capacity: 8 l Healthcare exercise: Maximum pressure: 6 bars Minimum pressure: 0.15 bar Quantity of hot water with ∆t=25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min DHW temperature selection range: 37 - 60 °C NB. THE BOILER WILL BE SUPPLIED WITH METHANE, THE ADJUSTMENT NECESSARY FOR LPG OPERATION WILL BE CARRIED OUT FREE OF CHARGE BY THE BERETTA ASSISTANCE CENTER DURING THE FIRST IGNITION. Beretta HELLO AT Hi AT, ideal for replacement in systems with radiators. Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving. High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger. Management: The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. The Ciao AT technology makes use of the condensing exchanger which recovers the latent heat of the fumes, the same principle used by condensing boilers. The exchanger, located at the top left, is connected directly to the fan which pushes the fumes inside it, before they are definitively expelled. The difference in the temperature of the fumes between the ~140°C inlet and the ~65°C outlet of the condensing exchanger is indicative of the amount of heat recovered from them. The return from the system first passes through the condensing exchanger which recovers the heat from the fumes, and then passes through the primary exchanger, where it receives the remaining heat in order to reach the required flow temperature. The water then recovers part of the heat from the fumes, which would otherwise be expelled into the atmosphere, thus giving rise to less waste and consequently greater savings for the user. Outdoor installation: Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required. Up to 17 meters of Ø 60 ducting with the Ciao AT boiler: With Ciao AT it is possible to comfortably duct even the most "difficult" flues thanks to the approval for Ø 60mm flue systems which is added to the traditional Ø 80 mm ducting flue system. The main 60mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. TECHNICAL FEATURES: Specific for systems with radiators and radiators (at high temperature) Condensing post exchanger in aluminum alloy Possibility of outdoor installation with antifreeze heater kit (optional) IPX5D electrical protection degree Environmental Self-Regulation System (SARA) Low consumption circulator 6 m (EEI≤0.20) Hydraulic connections cover (optional) Condensate collection neutralizer drawer kit (optional) Template, hydraulic fittings, gas and sanitary taps (optional) For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Seasonal heating efficiency % 94   Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 25/30 kW Nominal heating thermal power: 24.48 kW Efficiency at nominal power: 97.9% Efficiency at reduced load (30%): 103.5% Max electric power heating Watt 89 Electrical protection degree IP X5D Expansion vessel capacity 8 litres Quantity of hot water with Δt=25°C: 17 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 780x400x365 ; 38kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control Mynute Green E - ErP System energy class A+ (in combination with external probe and Rec 08 remote panel) Heating energy class A Energy class of the sanitary A New condensing exchanger Modulation 1:5 Flex low consumption circulator (IEE≤0.20) Ducting with flue Ø 50 mm   The new Mynute Green E range is designed following the ecodesign indications provided for by the European ErP Directive and is made up of two combined models and a heating only model. The combined versions have a thermal capacity of 20-25 kW and 25-30 kW, values ​​which refer respectively to heating and DHW; similarly, the heating only version has a thermal capacity of 25-30 kW. The range offers as standard the new front access condensing exchanger with improved efficiency (94% seasonal efficiency), the low consumption modulating circulator, the predisposition for the clapet kit (optional) to be used for pressurized flues and the high pressure fan. prevalence to be able to carry out the ducting of flues with Ø 60 or Ø 50 exhausts. Mynute Green E: high energy efficiency, low gas consumption and low emissions. The entry into force of the European Directive ErP (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Compulsory labeling provides greater transparency on the characteristics of the products which can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2 ) by 20%, increasing by 20 % use of renewable energies and reduce energy consumption by 20% in EU countries. The new Beretta condenser exchanger with front access The Mynute Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. With the new Beretta condensing exchanger, boiler performance improves up to an average seasonal efficiency of 94%. Mynute Green E, the elegant The new Mynute Green E is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to easily select all the functions necessary for using and setting the boiler. Flex modulating circulators: optimized performance, low consumption Mynute Green E uses a synchronous modulating circulator with low energy consumption, as required by the European ErP Directive. Thanks to this new technology, the electric motor of the circulator offers an Energy Effi ciency Index of less than 0.20, which means significantly reduced electricity consumption. The new circulator works proportionally to the power supplied by the boiler, thus contributing to a further reduction in electricity consumption. In case of need on the heating system, it is possible to change the head without having to replace the standard circulator with a high head one, the name “Flex” derives from this feature. Up to 49 meters of ducting With Mynute Green E it is possible to comfortably intubate even the most "difficult" flues thanks to the approval for flue Ø 50mm. The main 50mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. Characteristics: MYNUTE GREEN E + external probe + REC 08 remote control forms a class A+ system Designed according to the ecodesign indications provided for by the European ErP Directive Energy Class > heating (class A) > DHW profile XL (class A) Seasonal heating efficiency 94% Low polluting emissions: class 5 (UNI EN 483) New high-flow aluminum condensing exchanger with front access Standard thermoregulation (optional external probe) ErP boilers with low consumption modulating circulator (EEI0.20) modifiable up to 7m head Hydraulic connections cover (optional) Possibility of intubating flues with the special flue ø 60 in PP and ø 50 in PP (only ErP boilers) Template, plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres     Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

Technical features Code : 20095435 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Seasonal heating efficiency % 93 Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 25/29 kW Nominal heating thermal power: 24.45 kW Efficiency at rated power: 97.8% Efficiency at reduced load (30%): 102% Max electric power heating Watt 78 Electrical protection degree IP X5D Expansion tank capacity 8 litres Quantity of hot water with Δt=25°C: 17 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 715x405x248 ; 29kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control). Exclusive services: Beretta offers 5 years of peace of mind thanks to the Kasko warranty extension formulas. To view more product information CLICK HERE General characteristics HELLO GREEN ErP Ciao Green: high energy efficiency, low gas consumption and low emissions. The entry into force of the European ErP Directive (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Mandatory labeling provides greater transparency on the characteristics of products that can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2) by 20%, increasing by 20% the use of renewable energies and reduce energy consumption by 20% in EU countries. Condensing exchanger The innovative Beretta compact aluminum condensing exchanger is assembled with a brazing production process in a controlled atmosphere. In addition to allowing a more uniform distribution of heat, aluminum offers a high resistance to corrosion for the benefit of a longer duration over time. Aluminum is also chosen for its lightness, excellent conductivity, mechanical resistance, reliability and recyclability. The condensing exchanger makes it possible to recover a large part of the heat from the fumes by reducing losses in the chimney, and a large part of the latent heat, reaching a four-star energy efficiency value (according to European Directive EEC 92/42). The premix burner optimizes the combustion mixture by reducing NOx emissions to values ​​that place the boiler in Class 5, the highest according to the European Directive EN 677. Universal installation Ciao Green is designed to be installed outdoors in partially protected places or recessed thanks to the dedicated accessories and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit together with the siphon antifreeze heater kit. If the boiler is installed outside, without embedding, the lower cover is required for greater protection. The management The electronic panel is the brain of boiler management. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. A liquid crystal display and LEDs provide information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. Characteristics: ErP boilers with synchronous modulating pump with low energy consumption (EEI≤0.20) Designed according to the ecodesign indications provided for by the European ErP Directive Energy Class > heating (class A) > DHW profile XL (class A) Seasonal heating efficiency 93% Aluminum condensing exchanger, two versions of 25 kW and 29 kW combined and one 25 kW heating only Designed following the ecodesign indications of the European ErP Directive Class 5 according to the UNI EN 483 European Standard It can also be installed externally and recessed through the adoption of special kits (optional) Display for viewing temperature and diagnostic codes IPX5D electrical protection degree Prepared for connection to the remote control (optional) Standard thermoregulation (optional external probe) Plumbing fittings, gas and sanitary taps (optional) Antifreeze kit available up to -10°C (optional) Beretta is “ERP”. The concrete commitment towards an eco-sustainable future The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective. The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands. In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual devices. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Beretta open chamber water heater mod. FONTE LX 14 lt Low NOx Methane cod. 20149825 - NEW ErP ENERGY LABEL SPECIFICATIONS ACCORDING TO EUROPEAN ErP DIRECTIVE Sanitary energy efficiency Class A Sanitary load profile - M Characteristics Typology - Open chamber Draft - Natural draft Ignition - 2 x 1.5V batteries Flame control - by ionization Flame modulation - continued Hot water production ∆t=30° litres/min 11.6 Nominal heat input (G20 / G30-G31) kW 28.0 / 28.0 Rated thermal power (G20 / G30-G31) kW 24.36 / 24.75 Waterfall Withdrawal range - Idle selector litres/min from 2.5 to 6.5 Withdrawal range - Selector at maximum litres/min from 2.5 to 14 Water temperature elevation - Selector at minimum °C 50 Water temperature elevation - Selector at maximum 25 °C Minimum / normal / maximum pressure bar 0.2 / 2 / 10 Ø water connections - 1/2” DHW temperature selection range °C 35-60 Gas Nominal gas supply pressure (G20) mbar 20 Ø gas connection - 1/2” Dimensions and weight Dimensions (HxWxD) mm 675x400x230; 12Kg SOURCE LX new Low NOx open chamber water heater Within the new generation of low NOx emission products, Beretta presents Fonte Lx, the new instantaneous open chamber water heater, entirely Beretta signature both for know-how and for industrialization. The new Fonte Lx range, completely renewed in terms of aesthetics and planning, consists of two models, 11 and 14 liters respectively, available in both methane and LPG versions, with dedicated codes, able to offer maximum sanitary comfort in compliance with recent European regulations for the reduction of NOx emissions. The compactness and modernity of the design allow Fonte Lx to be easily placed in any living context, characteristics which, together with the simplicity of maintenance and use for the end user, distinguish Fonte Lx as a very appreciable product in the panorama of residential comfort. Modern and intuitive control panel Fonte Lx stands out for its ease of use for the end user, a feature that reconfirms one of the drivers of Beretta's technological research since its origins, aimed at creating products with maximum usability. The design of the new panel, modern and linear, in line with the new generation Beretta products, is characterized by an intuitive, backlit display, which immediately displays the water temperature in °C and the diagnostics of any anomalies, together with two icons indicating the presence of a flame and the battery charge level. Three command keys allow the end user to manage all the functions of the water heater. On the panel there is also a led that flashes when the battery level is low, thus signaling the need for their replacement. Characteristics Instantaneous open chamber water heater with dedicated methane and LPG versions Battery ignition (2 x 1.5V batteries supplied as standard) High sanitary load profile (XL on the 14 lt model) Abundant production of domestic hot water at Δt 25°C of 11 and 14 litres/min Innovative project design New self-adapting system with thermostatic device Increased modulation of power and domestic hot water flow, compared to the previous range Electronic reset from the user interface of the water and smoke thermostats, in the event of anomalies (RESET key) New Design Innovative interface with backlit display, 3 control keys and battery replacement LED Modern aesthetics and compact dimensions for an easy setting in any living environment Ease of use Simple and intuitive command keys Immediate visualization of the temperature on the display Battery charge level shown on display with LED to signal replacement High comfort Wide picking range and comfort High stability of the temperature of the hot water supplied Delivery of domestic hot water even with minimum withdrawals or low pressure Less consumption Thanks to the advanced electronic modulating flame regulation system Easy to install and maintain Quick and easy installation with no need to remove the casing Innovative electronic gas valve without membrane for zero-time maintenance Latest generation low NOx burner The new FONTE Lx line is able to satisfy the most demanding requirements in terms of low emissions in force since September 2018, as required by Regulation (EU) 814/2013 which requires emissions of nitrogen oxides equal to or lower than 56 mg/kWh . Thanks to the innovative FONTE Lx burner of the hyperstoichiometric type, cooled by water, a significant lowering of the polluting values ​​of carbon monoxide and nitrogen produced by combustion is obtained, such as to satisfy the new limits of international legislation with full marks. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase

Read more less

Beretta CIAO AT 25 csi LOW NOx condensing boiler Complete with flue kit Cod. 20151635 Technical specifications according to ErP directives Model: HELLO AT LOW NOx Sanitary energy efficiency class: A Energy efficiency class in heating: B Load profile: XL Product code 20151835 Natural gas supply Technical features: Indoor/Outdoor installation Nominal heat input 25 kW Nominal thermal power 23.85 kW Electric Power: 114W New version NOx < 56 mg/kWh NOx class 6 IPX5D electrical protection degree Expansion tank capacity: 9 l Dimensions Dimensions h/w/d (mm): 780/400/336 HELLO AT new LOW NOx model Hi AT, ideal for replacement in systems with radiators Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving. New burner with low NOx emissions Specific for systems with radiators and radiators (at high temperature) Condensing post exchanger in aluminum alloy Possibility of outdoor installation with antifreeze heater kit (optional) IPX5D electrical protection degree Environmental Self-Regulation System (SARA) Low consumption circulator 6 m (EEI≤0.20) Hydraulic connections cover (optional) Condensate collection neutralizer drawer kit (optional) Template, hydraulic fittings, gas and sanitary taps (optional) High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger. The management The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. Compatible with BeSMART The BeSMART WiFi Comfort Control Panel, optional compatible with Ciao AT, is the remote boiler management device with modulating chronothermostat functions. With the WiFi Box accessory, included in the BeSMART WiFi Comfort Control, it is also possible to manage comfort remotely using Smartphones and Tablets. The BeSMART WiFi control is very simple to install and intuitive to use and allows you to adjust the parameters and activate the many functions on the boiler. A large liquid crystal display shows all important information. Using the buttons on the control, the temperature of the heating water and domestic hot water is set easily and intuitively and the heating time programming is carried out. Outdoor installation Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board antifreeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less