SAVIO SuperEVOdens 24 S* METHANE CONDENSING Boiler Complete with Fume Exhaust Kit - ErP Model: SuperEVOdens 24S ErP specifications Class B heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Heating/DHW nominal heat input: 25 kW Heating/DHW maximum useful power: 24.4 kW Yield name 60°/80°C: 97.4% Yield at 30% load: 98.9% High yields (★★★★ compliant with yield directive 92/42 EEC and Legislative Decree 311/06) NOx class 2 Weighted NOx: 166 mg/kWh Minimum/maximum heating temperature: 40/85°C Minimum/maximum heating pressure 3.0/0.3 bar Expansion vessel capacity 8 l (total) Minimum/maximum domestic hot water temperature 35/60°C Maximum flow rate (ΔT=25K)/(ΔT=35K): 13.9/10 l/min Specific sanitary flow rate (ΔT=30 K): 11.6 l/min Voltage / Power at nominal heat input V~/ W 230/82 IPX4D degree of protection Dimensions HxWxD 803x400x350; 42.5 kgs Power supply: methane or LPG Standard Digital electronic room thermostat Boiler support bracket and paper template Condensate collection siphon Quick instruction to the user SuperEVO dens SuperEVOdens is the condensing boiler designed for traditional systems and easily adaptable to new underfloor systems using SIMpatico, a hot water distribution device for heating Savings and ease of use SuperEVOdens maintains the simplicity of management, programming and regulation of the traditional boiler and imports the savings of the condensing boiler deriving from the recovery of heat from the fumes. The heat recovery unit preheats the system water with the heat released by the fumes, heat which in traditional boilers is dispersed into the environment. This recovery of energy from the fumes, at typical operating temperatures of radiator systems, leads SuperEVOdens to have higher yields than traditional boilers. High yields (in compliance with yield directive 92/42 EEC and Legislative Decree 311/06) Copper lamellar primary heat exchanger with large exchange surface and double circulation Aluminum heat recovery unit to exploit the heat of the fumes and transfer it to the water Sanitary plate heat exchanger in stainless steel High efficiency pump with low energy consumption Digital control panel with backlit display Electronic card for: - Restart frequency adjustment - Adjustable primary circuit thermal inertia disposal - Circulator mode selection - Circulator anti-seize - Antifreeze safety - Chimney sweep function Integrated automatic by-pass 8 liter expansion vessel Immunity to radio interference Magnetic sanitary flow switch Absolute heating pressure switch IPX4D degree of protection High circulation primary exchanger It is the element that distinguishes the entire Savio range. It favors the flow of water into the heating system and, thanks to its reduced hydraulic resistance, adapts the boiler to the system and facilitates the transmission of heat to the radiators. Heat recovery The heat recovery recovers the heat from the fumes before they are expelled and preheats the water directed to the primary exchanger. The recuperator is made of aluminium, has a finned coil which determines a large exchange surface and has a device to ensure that the boiler discharges the condensate correctly Command panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Digital and analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display Display annual periodic maintenance expiry Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

SAVIO ACTA GAS BOILER AND 24 A* METHANE OPEN CHAMBER Model: ACTA 24A Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary Energy Efficiency Class B Withdrawal profile: XL Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 26.6 kW Heating/DHW maximum useful power: 24.1 kW Yield name 60°/80°C: 90.6% Yield at 30% load: 89.6% Energy efficiency stars: (dir 92/42/EEC) ** NOx class n° 3 Weighted NOx: 135 mg/kWh Minimum/maximum heating temperature: 38/85 °C Minimum/maximum heating pressure: 0.3/3.0 bar Capacity of the expansion tank (total): 8lt DHW minimum/maximum temperature: 35/60°C Maximum flow rate (ΔT=25K) / (ΔT=35K): 13.8/9.9 l/min Specific sanitary flow rate (ΔT=30 K): 11.5 l/min Voltage / Power at nominal heat input V~/ W 230~/56 Degree of protection n° IPX4D Minimum/maximum smoke temperature: 83/108°C Extremely compact dimensions hxwxd: mm 703x400x325 ; 28.7kg CNG or LPG power supply ACTA ACTA is the range of Savio boilers designed to meet modern housing needs that require reliable, compact and high performance products. The ACTA NEW range includes open chamber boilers with powers of 24 kW and 28 kW. The ACTA series is suitable for heating and domestic hot water production. ACTA has very compact dimensions which make it easy to place in any environment. Characteristics: High yields Primary heat exchanger in copper, high circulation lamellar Sanitary plate heat exchanger in stainless steel High efficiency pump with low energy consumption Integration with SAVIO solar systems using a solar kit Digital control panel with display. The electronic card allows you to: - Adjust the ignition pressure - Adjust the restart frequency - Manage the post-circulation of the high efficiency pump - View fault diagnostics and lockout status. Also available: - Boiler antifreeze safety - Disposal of primary circuit thermal inertia. Primary exchanger ACTA is a high efficiency boiler: the most compact exchanger, with reduced fin pitch to increase their number and ensure maximum efficiency. The large heat exchange surface is guaranteed by the helical section of the passage pipes and by the lamellar structure. The high exchange efficiency is guaranteed by the double circulation in counter flow. The exchanger is made of copper with a protective coating resistant to high temperatures. Secondary exchanger ACTA is available in a mixed version for heating and domestic hot water production: the hot water is supplied at an adjustable and constant temperature thanks to the electronic modulation of the boiler. The DHW exchanger is made of stainless steel and has a low inertia which guarantees excellent performance. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Digital and analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display Display annual periodic maintenance expiry Thermo-hydrometer for reading the water pressure on the primary side. Integration with solar ACTA can be easily combined with a solar system using the Biasi solar kit. Simple and immediate to install, it does not require electrical parts and allows optimizing the integration of the solar system with the boiler which intervenes only when necessary to guarantee the required comfort temperature. Reliability and security Hydraulic groups of innovative conception: Motorized 3-way valve Integrated automatic by-pass: allows the boiler to adapt to the needs of modern heating systems Absolute heating pressure switch: guarantees protection of the boiler in the event of a lack of water or circulation Sanitary flowmeter Easily accessible filling tap Drain tap Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

SAVIO ACTA GAS BOILER AND 24 A* METHANE OPEN CHAMBER Model: ACTA 24A Energy label specifications according to the European ErP directive Class C heating energy efficiency Sanitary Energy Efficiency Class B Withdrawal profile: XL Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 26.6 kW Heating/DHW maximum useful power: 24.1 kW Yield name 60°/80°C: 90.6% Yield at 30% load: 89.6% Energy efficiency stars: (dir 92/42/EEC) ** NOx class n° 3 Weighted NOx: 135 mg/kWh Minimum/maximum heating temperature: 38/85 °C Minimum/maximum heating pressure: 0.3/3.0 bar Capacity of the expansion tank (total): 8lt DHW minimum/maximum temperature: 35/60°C Maximum flow rate (ΔT=25K) / (ΔT=35K): 13.8/9.9 l/min Specific sanitary flow rate (ΔT=30 K): 11.5 l/min Voltage / Power at nominal heat input V~/ W 230~/56 Degree of protection n° IPX4D Minimum/maximum smoke temperature: 83/108°C Extremely compact dimensions hxwxd: mm 703x400x325 ; 28.7kg CNG or LPG power supply ACTA ACTA is the range of Savio boilers designed to meet modern housing needs that require reliable, compact and high performance products. The ACTA range includes open chamber boilers with powers of 24 kW and 28 kW. The ACTA series is suitable for heating and domestic hot water production. ACTA has very compact dimensions which make it easy to place in any environment. Characteristics: High yields Primary heat exchanger in copper, high circulation lamellar Sanitary plate heat exchanger in stainless steel High efficiency pump with low energy consumption Integration with SAVIO solar systems using a solar kit Digital control panel with display. The electronic card allows you to: - Adjust the ignition pressure - Adjust the restart frequency - Manage the post-circulation of the high efficiency pump - View fault diagnostics and lockout status. Also available: - Boiler antifreeze safety - Disposal of primary circuit thermal inertia. Primary exchanger ACTA is a high efficiency boiler: the most compact exchanger, with reduced fin pitch to increase their number and ensure maximum efficiency. The large heat exchange surface is guaranteed by the helical section of the passage pipes and by the lamellar structure. The high exchange efficiency is guaranteed by the double circulation in counter flow. The exchanger is made of copper with a protective coating resistant to high temperatures. Secondary exchanger ACTA is available in a mixed version for heating and domestic hot water production: the hot water is supplied at an adjustable and constant temperature thanks to the electronic modulation of the boiler. The DHW exchanger is made of stainless steel and has a low inertia which guarantees excellent performance. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Digital and analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display Display annual periodic maintenance expiry Thermo-hydrometer for reading the water pressure on the primary side. Integration with solar ACTA can be easily combined with a solar system using the Biasi solar kit. Simple and immediate to install, it does not require electrical parts and allows optimizing the integration of the solar system with the boiler which intervenes only when necessary to guarantee the required comfort temperature. Reliability and security Hydraulic groups of innovative conception: Motorized 3-way valve Integrated automatic by-pass: allows the boiler to adapt to the needs of modern heating systems Absolute heating pressure switch: guarantees protection of the boiler in the event of a lack of water or circulation Sanitary flowmeter Easily accessible filling tap Drain tap Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

SAVIO SuperEVOdens 28 S* LPG CONDENSING Boiler Complete with Fume Exhaust Kit - ErP Model: SuperEVOdens 24S ErP specifications Class B heating energy efficiency Sanitary energy efficiency Class A Withdrawal profile: XL Heating/DHW nominal heat input: 25 kW Heating/DHW maximum useful power: 24.4 kW Yield name 60°/80°C: 97.4% Yield at 30% load: 98.9% High yields (★★★★ compliant with yield directive 92/42 EEC and Legislative Decree 311/06) NOx class 2 Weighted NOx: 166 mg/kWh Minimum/maximum heating temperature: 40/85°C Minimum/maximum heating pressure 3.0/0.3 bar Expansion tank capacity 8 l (total) Minimum/maximum domestic hot water temperature 35/60°C Maximum flow rate (ΔT=25K)/(ΔT=35K): 13.9/10 l/min Specific sanitary flow rate (ΔT=30 K): 11.6 l/min Voltage / Power at nominal heat input V~/ W 230/82 IPX4D degree of protection Dimensions HxWxD 803x400x350; 42.5 kgs Power supply: methane or LPG Standard Digital electronic room thermostat Boiler support bracket and paper template Condensate collection siphon Quick instruction to the user SuperEVO dens SuperEVOdens is the condensing boiler designed for traditional systems and easily adaptable to new underfloor systems using SIMpatico, a hot water distribution device for heating Savings and ease of use SuperEVOdens maintains the simplicity of management, programming and regulation of the traditional boiler and imports the savings of the condensing boiler deriving from the recovery of heat from the fumes. The heat recovery unit preheats the system water with the heat released by the fumes, heat which in traditional boilers is dispersed into the environment. This recovery of energy from the fumes, at typical operating temperatures of radiator systems, leads SuperEVOdens to have higher yields than traditional boilers. High yields (in compliance with yield directive 92/42 EEC and Legislative Decree 311/06) Copper lamellar primary heat exchanger with large exchange surface and double circulation Aluminum heat recovery unit to exploit the heat of the fumes and transfer it to the water Sanitary plate heat exchanger in stainless steel High efficiency pump with low energy consumption Digital control panel with backlit display Electronic board for: - Restart frequency adjustment - Adjustable primary circuit thermal inertia disposal - Circulator mode selection - Circulator anti-seize - Antifreeze safety - Chimney sweep function Integrated automatic by-pass 8 liter expansion vessel Immunity to radio interference Magnetic sanitary flow switch Absolute heating pressure switch IPX4D degree of protection High circulation primary exchanger It is the element that distinguishes the entire Savio range. It favors the flow of water into the heating system and, thanks to its reduced hydraulic resistance, adapts the boiler to the system and facilitates the transmission of heat to the radiators. Heat recovery The heat recovery recovers the heat from the fumes before they are expelled and preheats the water directed to the primary exchanger. The recuperator is made of aluminium, has a finned coil which determines a large exchange surface and has a device to ensure that the boiler discharges the condensate correctly Command panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Digital and analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history Recommended fill display Display annual periodic maintenance expiry Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Overview SAVIO alDENS 24* CONDENSING BOILER COMPLETE WITH LPG FUME KIT LPG ideal for radiator systems - NEW ErP Technical specifications Model:ÿALDENS HE Product codeÿLPG: 103021021000 Product codeÿLPG: 103121029000 Technical data according to ErP directives Energy efficiency class in heating: A Sanitary energy efficiency class: A Load profiles: XLÿ Technical features: Minimum/Nominal useful power kW 2.9 ú 23.0 Minimum heat input with Methane/ Propan3.0 / 4.4 Efficiency class:ÿ Efficiency at nominal load in CONDENSATION % 100.9 Profitability at 30% of load% 98.6 NOx class 5 Operating temperature in heating min./maxøC 30 - 85 Adjustable temperature in sanitarywareøC 38 ú 60 DHW production mixed with t 25 l/min 13.2 Capacity of expansion vessel l 8 Supply voltageÿV-Hz 230/50 Degrees of protection IP X5D Dimensions HxWxD mm 700x420x345; 34 kgs Main features ALDENS ALDENS the new SAVIO range of condensing wall mounted boilers: excellent performance thanks to the aluminum heat exchanger and ease of use thanks to the control panel with knobs and display. Available in the combi version which combines the heating function and the production of domestic hot water. ALDENS presents a complete range of powers, 24 and 35 kW combi in the same extremely compact dimensions (700 x 420 x 345 mm). ALDENS has the strong point in the innovative primary heat exchanger in Al/Si/Mg with low water content designed to provide high yields that last over time. The digital display communicates the boiler operating parameters to the user in an easy and convenient way. Like the entire condensing range, SAVIO ALDENS allows you to make the most of savings from climatic thermoregulation, based on the system in which the boiler is installed. Main features: Outstanding fine 1:8 modulation ratio Efficiency>107% (ex dir. CE 92/42) Primary heat exchanger in ultra-flat Al/Si/Mg Electronics with HWS or Hot Water Speed ​​function? Low NOx (class 5 according to EN 297 and EN 483) thanks to the modulating premix burner Production of fine hot water 13.3 l/min t 25 with special 12-plate (mod. 24 kW) and 16-plate (mod. 35 kW) exchanger in stainless steel Maintenance or Pit Stop? simple and intuitive control panel High efficiency modulating circulator (in line with ErP Dir. 2015) Sanitary exchanger Sanitary comfort ensured by the suitably sized plate exchanger to guarantee the best performance in terms of domestic hot water, reducing the waiting time and guaranteeing temperature stability. Modulating circulator with deaerator It represents the state of the art in the standard of high efficiency. In line with the ErP directive of 2015, with less than 1 W of consumption in stand-by and only 45 W in maximum operation, thanks to the wide modulation capacity, based on the request of the room thermostat and the temperatures detected by the sensors placed on the delivery/return automatically doses the boiler power to the needs of the system. Particularly silent and compact, it integrates with the safety valve, the by-pass and the drain cock. Exclusive Ai/Si/Mg heat exchanger It is made in a special Aluminum/Silicon/Magnesium alloy which ensures its efficiency and resistance over time. Thanks to the configuration of internal heat exchangers, efficiencies higher than 107% are achieved in the condensing regime, which means great economic savings and very low environmental impact for the user. The 35 kW version suitably increased. Plus Manage 2 zones with 2 thermostats:ÿALDENS versatile. Ideal for all systems, thanks to the electronics that allow you to manage 2 different temperature heating zones (high for radiators and fan-coils, low for radiant panel systems) by controlling them with dedicated modulating and on-off thermostats.ÿ Anti-overheating post-circulation:ÿFor 15 seconds, it maintains the thermal balance between delivery and return, even after intense DHW withdrawals, while in heating, with a duration of 5 minutes, it allows all residual thermal inertia to be disposed of.ÿ Sliding temperature operations:ÿFor maximum running economy.ÿ Antifreeze protection:ÿIt intervenes at 5°C and is activated in both domestic hot water and heating, bringing the temperature in the boiler to 15°C. The risk is avoided that ALDENS may freeze if low temperatures persist in the room where it is installed. If there is a lack of gas, the block signal will appear on the display.ÿ Pump anti-blocking: blocking of the pump following long stops is avoided thanks to an automatic 5-second pulse that the electronics sends to the motor every 24 hours of stop The multifunction LCD display, with timed backlighting, allows: Reading of the heating and sanitary temperatures Display of lockout due to lack of flame Error code display Malfunction signaling Operating/stand-by status Burner operating status Diagnostics with signaling of 11 anomalies Ecodesign directive: from 2015 on new condensing boilers In fact, after very long negotiations, the ÿEcodesign regulationÿ was approved, which introduces a new energy labeling on minimum efficiency standards for boilers.ÿIn particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for appliances for the production of domestic hot water. ÿHence the obligation to installÿonly condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimneyÿas occurs in traditional boilers. The recovered heat is transferred to the heating system, making it possible to achieve a yield of 106% with 92% of the traditional boiler and 84/85% of an oldÿÿtraditional generator.ÿThe installation obligation concerns manufacturers of boilers which will no longer be able to place on the market non-condensing starting from 26 September 2015. This means that starting from this date, anyone who wants to install a boiler in their own home will have to install only condensing models. Only one particular type of non-condensing boiler will continue to be produced which is technically called open room? to be installedÿ when it is not possible to replace an old boiler with a condensing boilerÿdue to problems related to the collective flueÿof some multi-family buildings. Products for heating water and the environment represent around 30% of the world's energy consumption in Europe.ÿ Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations like Italy were deactivated. As of 26 September 2015, the ErP regulation and ÿenergy labelingÿwill be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and hot water storage tanks) u. How to read energy labels There are different labels, based on the type and function of the product (only room water heating of both, and in this case the label must bear both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise levels, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase. Shipping From the day payment is received, the product will be shipped within 3 working days. Free insured shipping for Italy. Shipping will take place via one of the national carriers

Read more less

Overview SAVIO alDENS 24* CONDENSING BOILER COMPLETE WITH LPG METHANE FUME KIT ideal for radiator systems - NEW ErP Technical specifications Model:ÿALDENS HE Product codeÿLPG: 103021021000 Product codeÿMETHANE: 103121029000 Technical data according to ErP directives Energy efficiency class in heating: A Sanitary energy efficiency class: A Load profiles: XLÿ Technical features: Minimum/Nominal useful power kW 2.9 ú 23.0 Minimum heat input with Methane/ Propan3.0 / 4.4 Efficiency class:ÿ Efficiency at nominal load in CONDENSATION % 100.9 Profitability at 30% of load% 98.6 NOx class 5 Operating temperature in heating min./maxøC 30 - 85 Adjustable temperature in sanitarywareøC 38 ú 60 DHW production mixed with t 25 l/min 13.2 Capacity of expansion vessel l 8 Supply voltageÿV-Hz 230/50 Degrees of protection IP X5D Dimensions HxWxD mm 700x420x345; 34 kgs Main features ALDENS ALDENS the new SAVIO range of condensing wall mounted boilers: excellent performance thanks to the aluminum heat exchanger and ease of use thanks to the control panel with knobs and display. Available in the combi version which combines the heating function and the production of domestic hot water. ALDENS presents a complete range of powers, 24 and 35 kW combi in the same extremely compact dimensions (700 x 420 x 345 mm). ALDENS has the strong point in the innovative primary heat exchanger in Al/Si/Mg with low water content designed to provide high yields that last over time. The digital display communicates the boiler operating parameters to the user in an easy and convenient way. Like the entire condensing range, SAVIO ALDENS allows you to make the most of savings from climatic thermoregulation, based on the system in which the boiler is installed. Main features: Outstanding fine 1:8 modulation ratio Efficiency>107% (ex dir. CE 92/42) Primary heat exchanger in ultra-flat Al/Si/Mg Electronics with HWS or Hot Water Speed ​​function? Low NOx (class 5 according to EN 297 and EN 483) thanks to the modulating premix burner Production of fine hot water 13.3 l/min t 25 with special 12-plate (mod. 24 kW) and 16-plate (mod. 35 kW) exchanger in stainless steel Maintenance or Pit Stop? simple and intuitive control panel High efficiency modulating circulator (in line with ErP Dir. 2015) Sanitary exchanger Sanitary comfort ensured by the suitably sized plate exchanger to guarantee the best performance in terms of domestic hot water, reducing the waiting time and guaranteeing temperature stability. Modulating circulator with deaerator It represents the state of the art in the standard of high efficiency. In line with the ErP directive of 2015, with less than 1 W of consumption in stand-by and only 45 W in maximum operation, thanks to the wide modulation capacity, based on the request of the room thermostat and the temperatures detected by the sensors placed on the delivery/return automatically doses the boiler power to the needs of the system. Particularly silent and compact, it integrates with the safety valve, the by-pass and the drain cock. Exclusive Ai/Si/Mg heat exchanger It is made in a special Aluminum/Silicon/Magnesium alloy which ensures its efficiency and resistance over time. Thanks to the configuration of internal heat exchangers, efficiencies higher than 107% are achieved in the condensing regime, which means great economic savings and very low environmental impact for the user. The 35 kW version suitably increased. Plus Manage 2 zones with 2 thermostats:ÿALDENS versatile. Ideal for all systems, thanks to the electronics that allow you to manage 2 different temperature heating zones (high for radiators and fan-coils, low for radiant panel systems) by controlling them with dedicated modulating and on-off thermostats.ÿ Anti-overheating post-circulation:ÿFor 15 seconds, it maintains the thermal balance between delivery and return, even after intense DHW withdrawals, while in heating, with a duration of 5 minutes, it allows all residual thermal inertia to be disposed of.ÿ Sliding temperature operations:ÿFor maximum running economy.ÿ Antifreeze protection:ÿIt intervenes at 5°C and is activated in both domestic hot water and heating, bringing the temperature in the boiler to 15°C. The risk is avoided that ALDENS may freeze if low temperatures persist in the room where it is installed. If there is a lack of gas, the block signal will appear on the display.ÿ Pump anti-blocking: blocking of the pump following long stops is avoided thanks to an automatic 5-second pulse that the electronics sends to the motor every 24 hours of stop The multifunction LCD display, with timed backlighting, allows: Reading of the heating and sanitary temperatures Display of lockout due to lack of flame Error code display Malfunction signaling Operating/stand-by status Burner operating status Diagnostics with signaling of 11 anomalies Ecodesign Directive: from 2015 on new condensing boilers In fact, after very long negotiations, the ÿEcodesign regulationÿ was approved, which introduces a new energy labeling on minimum efficiency standards for boilers.ÿIn particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for appliances for the production of domestic hot water. ÿHence the obligation to installÿonly condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimneyÿas occurs in traditional boilers. The recovered heat is transferred to the heating system, making it possible to achieve a yield of 106% with 92% of the traditional boiler and 84/85% of an oldÿÿtraditional generator.ÿThe installation obligation concerns manufacturers of boilers which will no longer be able to place on the market non-condensing starting from 26 September 2015. This means that starting from this date, anyone who wants to install a boiler in their own home will have to install only condensing models. Only one particular type of non-condensing boiler will continue to be produced which is technically called open room? to be installedÿ when it is not possible to replace an old boiler with a condensing boilerÿdue to problems related to the collective flueÿof some multi-family buildings. Products for heating water and the environment represent around 30% of the world's energy consumption in Europe.ÿ Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations like Italy were deactivated. As of 26 September 2015, the ErP regulation and ÿenergy labelingÿwill be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and hot water storage tanks) u. How to read energy labels There are different labels, based on the type and function of the product (only room water heating of both, and in this case the label must bear both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise levels, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase. Shipping From the day payment is received, the product will be shipped within 3 working days. Free insured shipping for Italy. Shipping will take place via one of the national carriers

Read more less

Overview SAVIO SuperEVOdens 24 S* CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW CLASS A MODEL - ERP Technical specifications o Model: SuperEVOdens 24 S* Energy label specifications according to the European ErP directive o Class A heating energy efficiency o Domestic energy efficiency profile XL Class A o Withdrawal profile: XL Characteristics of heating/DHW operation: o Heating / domestic hot water nominal heat input kW 25.0 o Heating / domestic hot water maximum useful power kW 24.4 o Efficiency at nominal heat input (60/80°C): 97.4% o Efficiency at nominal heat input (30/50°C): 97.1% o Efficiency at 30% at 30°C: 98.9% o Energy efficiency n° ???? o Minimum / maximum heating temperature ** °C 40 / 85 o Expansion vessel capacity (total / useful) l 8.0 / 4.0 o Minimum / maximum domestic hot water temperature °C 35 / 60 o Maximum flow rate (T=25 K) / (T=35 K) l/min 13.9 / 10.0 o Specific sanitary flow rate (T=30 K) *** l/min 11.6 o Total absorbed electric power W 65 o Degree of protection n° IPX4D o Dimensions (HxWxD) mm 803x400x350 o NOx class n° 2 o Power supply: METHANE Main features SuperEVO dens SuperEVOdens is the condensing boiler designed for traditional systems and easily adaptable to new underfloor systems using SIMpatico, a hot water distribution system for heating. Characteristics: o High yields (in compliance with yield directive 92/42 EEC and Legislative Decree 311/06) o Copper lamellar primary heat exchanger with large exchange surface and double circulation o Aluminum heat recovery unit to exploit the heat of the fumes and transfer it to the water o Sanitary plate heat exchanger in stainless steel o High efficiency pump with low energy consumption o Digital control panel with backlit display o Electronic card for: o Adjustment of restart frequency - Adjustable primary circuit thermal inertia disposal - Circulator mode selection - Circulator anti-seize - Antifreeze safety - Chimney sweep function o Integrated automatic by-pass o Immunity to radio interference o Magnetic sanitary flow switch o Absolute heating pressure switch o IPX4D degree of protection Savings and ease of use SuperEVOdens retains the simplicity of management, programming and regulation of the traditional boiler and imports the savings of the condensing boiler deriving from the recovery of heat from the fumes. The heat recovery unit preheats the system water with the heat released by the fumes, heat which in traditional boilers is dispersed into the environment. This recovery of energy from the fumes, at typical operating temperatures of radiator systems, leads SuperEVOdens to have higher yields than traditional boilers. Main features High circulation primary exchanger It is the element that distinguishes the entire Savio range. It favors the flow of water into the heating system and, thanks to its reduced hydraulic resistance, adapts the boiler to the system and facilitates the transmission of heat to the radiators. Heat recovery The heat recovery recovers the heat from the fumes before they are expelled and preheats the water directed to the primary exchanger. The recuperator is made of aluminium, has a finned coil which determines a large exchange surface and has a device to ensure that the boiler correctly discharges the condensate. Thermoregulation By connecting the external probe (optional) directly to the boiler, climatic regulation can be used. SuperEVOdens will adapt the system water temperature to the external climatic conditions, ensuring that the desired room temperature is reached without waste and optimizing consumption. By using the climatic regulation, the regulation efficiency is also raised, giving greater value to your home. Eco-design directive After very long negotiations, the Ecodesign regulation was approved which introduces a new energy labeling on the minimum efficiency standards for boilers. In particular, an energy classification from A+ to G is envisaged for space heating appliances and from A to G for domestic hot water production appliances. Hence the obligation to install only condensing boilers, heat generators capable of recovering a large part of the latent heat contained in the fumes which, otherwise, would be dispersed in the chimney as occurs in traditional boilers. The recovered heat is transferred to the heating system, allowing to reach an efficiency of 106% against 92% of the traditional boiler and 84/85% of an old traditional generator. The installation obligation concerns boiler manufacturers who will no longer be able to place non-condensing boilers on the market starting from 26 September 2015. This means that starting from this date, anyone who wants to install a boiler in their own home will only have to install models condensing. Only a particular type of non-condensing boiler will continue to be produced which is technically called "open chamber" to be installed when it is not possible to replace an old boiler with a condensing boiler due to problems related to the collective flue of some multi-family buildings . What is Energy Labeling? Products for heating water and the environment represent around 30% of internal energy consumption in Europe. Designing eco-friendly products and promoting high performance technologies to end users in 2020 will lead to: o An annual energy saving equivalent to 56 million tons of oil, quantifiable to the savings obtained if the water and environmental heating systems of two large nations such as Italy were deactivated. As of 26 September 2015, ErP regulation and energy labeling will be applied in Europe to water and space heating products (boilers, heat pumps, micro-CHP devices, water heaters, and water storage tanks hot)¹. How to read energy labels There are different labels, based on the type and functions of the product (water heating or space heating only or both, and in this case the label must show both classifications). In addition to the energy class, the label provides other information that could be useful for understanding which product has the least environmental impact (for example power and consumption in different climatic zones, noise, etc.). It is possible to increase the energy efficiency of hot water production and space heating by connecting several products and accessories in one system. In this case it is necessary to prepare a system label in addition to that relating to the single product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less