Digital Room Thermostat Vaillant mod. Calormatic VRT 250 cod. 0020170569 on/off calorMATIC 250 is a room chronothermostat that can be programmed on a weekly basis and can be combined with any boiler on the market or to control zone valves. By sending an ON-OFF signal to the electronics of the connected device, calorMATIC 250 can set two temperature levels, one for "daytime heating" and one for "nighttime lowering". Through an interface with buttons and a large digital display, the user can at any time, in addition to always displaying the real room temperature, change the temperature and programming settings with a few simple steps. The calorMATIC 250 range consists of two control units, the model with wired connection and the model with radio wave connection (f) with receiver supplied. Weekly programming Backlit display Heating management Manual operation Wireless models Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€83,00
Technical features Sanitary efficiency class: A; Sanitary load profile: M; Performance: Domestic hot water production (ΔT = 25K): 11.0 l/min; Domestic hot water production (ΔT = 35K): 7.8 l/min; Minimum hot water flow rate: 2.5 l/min; Thermal power (min/max): 5.3/21.3 kW; Power supply: 230/50V/Hz; Total electric power: 123W; Electric power without antifreeze device: 46 W; Inlet gas pressure: 20/37 mbar; Methane fumes discharge temperature (min.max): 100/200 °C; Maximum operating overpressure: 10 bar; Admissible operating pressure range (min./max): 0.2/10 bar; DHW temperature (min.max): 38-60 °C; Sanitary fittings: G 1/2" inch; Gas connection: G 1/2" inch; Fume exhaust connection: 60/100 mm; Sound power dBA 65 67 68 Minimum operating temperature: -25°C; IP degree of protection IP X5D; Power supply: LPG or Propane gas (G31) Dimensions (HxWxL): 609x180x413mm; Weight: 19Kg; General characteristics Vaillant OutSide Mag water heater designed to always guarantee the same temperature of the water being dispensed. A particular feature of this water heater is its easy installation for outdoors, not even requiring connections to the flue, thanks to a facade drain already integrated in the front panel, it also guarantees very high resistance to atmospheric agents and the coldest temperatures (up to -25°C). Studied in detail, also through a modern and innovative design built with high efficiency materials, which not only fit into any environment, but through the front air intake always ensures the correct oxygen supply to ensure that the device work properly. All managed by a high technology that through a display or Touch interface, simple and intuitive to use, allows the rapid management of your comfort, and has a special function that through a loud acoustic signal, warns you in case there is an overflow from the tub during ACS output. Advantages: New version with improved performance; Extremely compact dimensions; Wide modulation range; Perfect dispensing temperature stability; Design and intuitive touch screen;
€250,00
ATTENTION THE BOILER IS BORN WITH METHANE AND IS ADJUSTABLE TO LPG. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Product name VAILLANT ecoTEC PLUS condensing BOILER VMW 306/5-5+ Technical features For heating and domestic hot water production Forced draft sealed chamber Heating efficiency class A Sanitary efficiency class A Sanitary load profile XL Nominal thermal power in DHW 30.0 kW Efficiency at 30% 109.0 Performance stars (Dir. 92/42CEE) **** NOx class 5 Degree of protection IP X4 D Expansion vessel capacity 10 l Domestic hot water production (ΔT = 30K) 14.3 l/min Power supply V/Hz 230/50 Dimensions HxWxD: 720-338-440 mm; 37 kgs Power supply: methane or LPG General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS VMW+ The most efficient and versatile combi condensing boiler there is. ecoTEC plus. Wall-mounted condensing boilers capable of always guaranteeing maximum efficiency and maximum comfort. This is German quality. ecoTEC plus has always been the most popular Vaillant boiler. Today it guarantees even lower consumption, a further increase in efficiency and versatility and the certainty of immediate sanitary comfort without jolts. The best of Vaillant technology to satisfy every need Every component and every function of ecoTEC plus has been designed to combine efficiency and reduced consumption in favor of greater respect for the environment. ecoTEC plus self-adapts to your needs by always choosing the most economical solution, mixing the right amount of gas and air; all this with an electrical consumption of less than 2 Watts (less than half of a radio in operation). The combined version satisfies all comfort needs, guaranteeing both constant hot water without sudden changes in temperature and a comfortable climate. Sanitary comfort, in particular, is managed by the efficient Aqua Comfort pre-heating system which, thanks to 4 probes, controls, verifies and guarantees the immediate delivery of hot water always at the same temperature. Lots of hot water, immediately, without sudden changes is the real comfort offered by ecoTEC plus. From today it can also be installed outdoors where the climate is mild even in winter. In fact, the boiler has a standard antifreeze device which allows it to resist down to -5°C. To have heating and domestic hot water in a single solution The VMW ecoTEC plus condensing wall-mounted boilers combine the production of domestic hot water with the heating function. Unlike all the other boilers, the Vaillant ELGA system is installed inside, which expands the modulation range, but above all electronically regulates and monitors combustion to always ensure the lowest gas consumption, guaranteeing maximum efficiency. The boiler adjusts itself automatically and continuously, as if it were assisted every 30 seconds. In addition to a new, simpler and more intuitive design, the new electronics together with a very high efficiency pump make ecoTEC plus VMW+ the wall-mounted condensing boiler that consumes less on the European market. the ecoTEC plus VMW+ boiler is compatible with all Vaillant components and accessories already on the market. The dimensions are reduced 70cm high, 44cm wide and 35cm deep (identical to the previous version), the weight has been optimized making installation easier. and with vSMART... and go to Class A+ (Optional). All models of the ecoTEC plus VMW+ range have an efficiency etas = 94%. For this reason, if combined with a class VI thermoregulation (such as vSMART), they reach a system efficiency of 98% and therefore the ErP energy class in heating A+. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.749,00
BOILER SUPPLIED WITH CONVERTIBLE METHANE THROUGH A SERVICE CENTER Overview VAILLANT ecoTEC PLUS CONDENSING BOILER VMW 256/5-5 + vSMART WiFi COMPLETE WITH FUME KIT - NEW ErP 2015 METHANE Cod. 0020222964ÿ Technical specifications For heating and domestic hot waterÿ Forced draft sealed chamber Nominal heat input in sanitarywarekW 25 ErP energy class (Heating and DHW): class A Stars of yield (according to Dir. 92/42CEE) - **** Domestic hot water production (T = 30K) 11.9 lt Domestic hot water comfort stars (prEN 13203) - *** Expansion tank capacity 10 l Massimcontenutd?Ó?water in plantl 180 Dimensions (hxpxl) mm 720 x 338 x 440 Total electric power/pump (max speed) W 80/35 NOx class - 5 Adjustable in wi-fi from smartphone ThermostatvSMART as standard Version:ÿMETHANEÿ Features list Vaillant condensing boilerÿ With the strategic plan 20/20/20, Europe has the goal of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. Tuttquestentril 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for energy-using equipment, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes in the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation even at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS ecoTEC plus the excellence of wall-mounted condensing boilers minimum consumption, maximum efficiency and versatility TheÿecoTEC plus series, wall-mounted condensing boiler of the latest generation, conceived to guarantee maximum energy savings and maximum comfort and designed to satisfyÿthe requirements of European regulationsÿconcerning energy efficiency which will enter into force inÿSeptember 2015. In addition, all the new products and systems for heating and water production hot water heaters must be labeled with an indication of their energy efficiency class. TheÿecoTEC plusÿlabeling signals theÿclass A. ecoTEC plusÿreaches this result easily because, in addition to the typical elements of Vaillant boilers, it has new completely innovative components: the combustion management system (ELGA), which, skilfully mixing air and gas, results in a reduction in gas consumption, new electronics and the very high efficiency to ensure considerable savings in electricity. For example, the electricity consumption of the boiler in stand-by is less than 2Watt (less than half of a working radio). ecoTEC plusÿguarantees maximum comfort: the boiler supplies immediately available hot water without sudden changes in temperature. Thanks to its small dimensions (70 cm high, 44 cm wide and 35 cm deep)ÿecoTEC plusÿ can be easily installed on any wall. Today it is possible to install it outdoors where the climate is mild even in winter. ecoTEC plusÿhas, in fact, also an anti-gel device which allows it to resist up to temperatures that reach -5°C. The newÿsimple and intuitive design, thanks to the display with clear text and backlighting, makes the boiler functional, allowing the user easy setting and simple control. ecoTEC plus compatible with all Vaillant components and accessories already on the market. Features:ÿ Boiler ready for 2015 regulations ErP: class A Preheat DHWÿ *** DHW comfortÿ Antigel-5øC as standard **** Efficiency in heating Modulation 1:8ÿ Modulating pump (Class A) Primary heat exchanger Vasexpansion 10 lÿ ELGA combustion system transfer kit from methane propan supplied WiFi programming from smartphone tablet wherever you are with vSMART and App vSMART VaillantÿvSMARTÿ the advanced WiFi thermoregulation system that allows you to configure the comfort of your home at any time with a simple click on your smartphone tablet. The benefits of vSMART are not limited to convenience. Using andvSMART you drastically reduce the start/stop cycles of the boiler thus allowing you to save on gas and electricity and to extend the life of your appliance. vSMARTÿtransforms your smartphone tablet into a remote control system for your heating. Wherever you are and whatever you are doing, you will be able to control and adjust the comfort of your home in extremely intuitive mod-rapid using your WiFi network. Download the free ÿvSMARTÿapp from the tuStore. To download the App, simply enter the tuStore, search for vSMART and start the download. The Vaillant vSMART App is available for iOS and Android systems. vSMARTÿ Designed to ensure comfort and extreme ease of use. You can install it on the wall by connecting it to the electricity supply and place it where you prefer using common AA + batteries. Elegant and essential, it integrates perfectly into any environment. One device to save energy for others. With vSMART you can - Control heating and domestic hot water via App.ÿ - Have 30 pre-configured and customizable standard profiles available.ÿ - Monitor energy efficiency at all times.ÿ - Control the heating systems of several homes (e.g. two flats, two houses).ÿ - Check the historical data of temperature, mode and hours of operation.ÿ - Regulate the temperature based on climate data collected from the internet.ÿ - Quickly set the function or Away from Home? or Antifreeze? for greater savings.ÿ - Take advantage of the self-learning function that recognizes your programming over time to make your life even easier. The new EU legislation Starting from 26 September 2015 it is no longer possible to produce traditional forced draft boilers. Instead, it will be possible to continue producing condensing boilers and traditional open chamber boilers equipped with high efficiency pumps and compliant with the new ErP requirements such as emission levels, noise levels and efficiency. In particular, the installation of traditional open chamber boilers will only be possible in replacement of old boilers installed in multi-family buildings which discharge fumes into branched collective flues (CCR). Products placed on the market before 26/09/2015 that do not comply with the requirements of the new directive, such as traditional forced draft boilers and boilers not equipped with a high efficiency pump, can still be purchased, sold and installed. ErP and ELD: what they mean and how they differ ErP: The EU has issued new obligations for Energy Using Products (ErP). The new directive, known as the Ecodesign directive, prescribes minimum efficiency requirements and emission limits for appliances that produce heating and domestic hot water. The Ecodesign directive addresses two relevant product categories for installers and retailers in the sector: -ÿCategory 1ÿIncludes space heating appliances: electric, gas, oil, combined boilers, heat pumps and cogenerators up to 400 kW. -ÿCategory 2ÿIncludes appliances for the production of domestic hot water: electric, gas, diesel, heat pumps for DHW, solar systems up to 400 kW and boilers up to 2000 litres. ELD:ÿIn addition to the ErP directive, the EU has also introduced mandatory energy labeling for the same types of appliances up to 70 kW and boilers up to 500 litres. The energy labeling directive is called ELD and requires that new products and systems for heating and domestic hot water production are labeled with an indication of their energy efficiency class. By combining products and components, for example by adding a temperature control unit, the energy classification of the system can be increased, which will be calculated by the installer and indicated on the package label. 7 year guarantee The 7-year guarantee on new boilers is another excellent reason to offer Vaillant to your customers. In addition, know that by replacing a Vaillant boiler over 15 years old with a new generation one, the warranty extension will be provided free of charge by the Official Vaillant Technical Assistance Center against a maintenance contract. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.589,00
NB: in the absence of the product, the new VMW 26 CS model will be shipped VAILLANT ecoTEC PLUS condensing BOILER VMW 256/5-5+ Technical features: For heating and domestic hot water production Forced draft sealed chamber Heating efficiency class A Sanitary efficiency class A Sanitary load profile XL Nominal thermal power in DHW 25.0 kW Efficiency at 30% 110.0 Performance stars (Dir. 92/42CEE) **** NOx class 5 Path : p » span Words: 712 Degree of protection IP X4 D Expansion tank capacity 10 l Domestic hot water production (ΔT = 30K) 11.9 l/min Power supply V/Hz 230/50 Dimensions HxWxD: 720-338-440 mm; 36 kgs Power supply: methane or LPG Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS VMW+ The most efficient and versatile combi condensing boiler there is. ecoTEC plus. Wall-mounted condensing boilers capable of always guaranteeing maximum efficiency and maximum comfort. This is German quality. ecoTEC plus has always been the most popular Vaillant boiler. Today it guarantees even lower consumption, a further increase in efficiency and versatility and the certainty of immediate sanitary comfort without jolts. The best of Vaillant technology to satisfy every need Every component and every function of ecoTEC plus has been designed to combine efficiency and reduced consumption in favor of greater respect for the environment. ecoTEC plus self-adapts to your needs by always choosing the most economical solution, mixing the right amount of gas and air; all this with an electrical consumption of less than 2 Watts (less than half of a radio in operation). The combined version satisfies all comfort needs, guaranteeing both constant hot water without sudden changes in temperature and a comfortable climate. Sanitary comfort, in particular, is managed by the efficient Aqua Comfort pre-heating system which, thanks to 4 probes, controls, verifies and guarantees the immediate delivery of hot water always at the same temperature. Lots of hot water, immediately, without sudden changes is the real comfort offered by ecoTEC plus. From today it can also be installed outdoors where the climate is mild even in winter. In fact, the boiler has a standard antifreeze device which allows it to resist down to -5°C. To have heating and domestic hot water in a single solution The VMW ecoTEC plus condensing wall-mounted boilers combine the production of domestic hot water with the heating function. Unlike all the other boilers, the Vaillant ELGA system is installed inside, which expands the modulation range, but above all electronically regulates and monitors combustion to always ensure the lowest gas consumption, guaranteeing maximum efficiency. The boiler adjusts itself automatically and continuously, as if it were assisted every 30 seconds. In addition to a new, simpler and more intuitive design, the new electronics together with a very high efficiency pump make ecoTEC plus VMW+ the wall-mounted condensing boiler that consumes less on the European market. the ecoTEC plus VMW+ boiler is compatible with all Vaillant components and accessories already on the market. The dimensions are reduced 70cm high, 44cm wide and 35cm deep (identical to the previous version), the weight has been optimized making installation easier. and with vSMART... and go to Class A+ (Optional). All models of the ecoTEC plus VMW+ range have an efficiency etas = 94%. For this reason, if combined with a class VI thermoregulation (such as vSMART), they reach a system efficiency of 98% and therefore the ErP energy class in heating A+. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.597,00
NB: IN THE ABSENCE OF THE PRODUCT THE FOLLOWING MODEL VMI 35 WILL BE SHIPPED VAILLANT ecoTEC PLUS CONDENSING BOILER VMI 346/5-5 with boiler COMPLETE WITH FUME KIT - ErP LPG Technical features ErP energy class (Heating and DHW): class A Sanitary load profile - XL For heating and domestic hot water production Forced draft sealed chamber Nominal thermal power in sanitary kW 34 DHW nominal heat input kW 34 Performance stars (according to Dir. 92/42CEE) - **** Consumption at nominal power Natural gas m3 /h 3.7 Expansion vessel capacity 10 l Maximum water content in the system l 180 Storage tank setting temperature °C 35 - 65 Boiler nominal volume l 20 Minimum water flow l/min 1.5 Hot water withdrawal capacity (ΔT = 30K) l/10min 199 Domestic hot water comfort stars (prEN 13203) - *** Dimensions (hxpxl) mm 720x567x440; 59.5kg Power supply V/Hz 230/50 Total electric power W 115 Sound power dBA 49 IP degree of protection IP X4 D NOx class - 5 Version: CNG (0010019531) To view more product information CLICK HERE General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS with boiler Little space and a large family? ecoTEC plus with built-in wall-mounted boiler is the boiler designed to satisfy a high demand for hot water when spaces do not allow for the installation of external boilers. The VMW ecoTEC plus with actoSTOR CL 20 S integrable storage tank are available in power ratings of: 30 and 34 kW. This stratification boiler is a real hot water reserve that can be installed very easily and quickly directly between the wall and the boiler. An exceptional solution that ensures the quantity of water needed is always available and without sudden changes in temperature. The boiler system with storage tank is very simple to assemble: first install the actoSTOR CL wall-mounted storage tank and the related pipes supplied for domestic water, then hang the ecoTEC plus VMW wall-mounted boiler on the storage tank. The dimensions are very small 70cm high, 44cm wide and 55cm deep. The stratification storage tank guarantees the same performance as a storage tank with a 60-litre coil but with considerably reduced spaces. The combination with ecoTEC plus allows you to exclude the storage tank functionality by making the boiler work instantaneously; this allows a considerable saving on gas consumption. New electronics and a very high efficiency pump make ecoTEC plus the wall-mounted condensing boiler that consumes less on the European market. ecoTEC plus is compatible with all Vaillant components and accessories already on the market. The new design is simple and intuitive. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.903,00
Technical features ErP energy class: Class A Nominal heat output: 21.3 kW DHW direct withdrawal range ΔT = 25°C: 2.5 - 11 l/min Forced draft sealed chamber Ignition: electronic Compact dimensions (HxDxL): 600x183x385 mm Power supply: LPG General characteristics turboMAG plus Extremely compact dimensions Wide modulation range Perfect dispensing temperature stability Design and intuitive touch screen Energy efficiency class up to A depending on the model. Domestic hot water Instantaneous forced draft water heaters, with electronic ignition with wide modulation range and extremely compact dimensions: among the smallest on the market. The turboMAG plus water heaters guarantee plenty of hot water immediately, always at a constant temperature and maximum operational safety. Precisely safety is the added value of this range of water heaters. The Vaillant research and development team, which has been focused on ensuring leadership in the sector for over 140 years, has developed turboMAG plus with the target of safety: in fact, 26 control to ensure maximum user reliability. The new turboMAG plus are water heaters equipped with a three-stage combustion system which broaden the modulation range ensuring perfect temperature stability during hot water delivery. A new exchanger raises the performance of the water heater which, in the 11 – 14 – 16 liters per minute versions, offers a flexible choice for every user. turboMAG plus allows 360° installation flexibility: inside apartments and also outside, resisting temperatures down to -15°C (thanks to the antifreeze accessory) and rain (IPX5D approval). A solar kit as an accessory also allows you to pre-heat the incoming water, further reducing gas consumption. turboMAG plus (hot water production) is the new version of forced draught water heaters with DHW flow rates of: 11, 14 and 16 litres/minute running on Natural Gas and LPG. Quality Continuous development since 1874: Vaillant has been accredited for its superior quality Careful selection of components that meet the highest requirements and guarantee perfect functionality Modern Design: The well-designed casing with high-quality appearance that fits perfectly into your home Total safety: 26 safety functions guarantee the functioning of the appliance Water heater interface with touch screen (IMD): Display with maximum water protection IPX5D protection : Tested with water jets up to a maximum of 12.5 l/min from all directions Flexible and efficient Exchanger with high efficiency: Water heating with minimum gas consumption and lower bill consumption Burner with high modulation : Precise regulation of the thermal power in relation to the DHW request Reduced noise thanks to fan modulation : between 2,400 and 4,800 rpm Various DHW production profiles (bath or shower): - Bath filling mode: monitoring of the filling volume - Normal: temperature setting 38-60 °C Simplified replacement: Same flue position and wall bracket, Reduced installation time High comfort 11, 14 & 16 liters of DHW production High modulation 1:4 Maximum temperature stability in DHW supply : Avoid unwanted temperature variations 3 level combustion : High modulation range 25-100% Ecodesign Directive (ErP) 2015 How to be ready for new EU legislation What will happen from 26 September 2015? From this date it will no longer be possible to produce traditional forced draft boilers. Instead, it will be possible to continue producing condensing boilers and traditional open chamber boilers equipped with high-efficiency pumps and compliant with the new ErP requirements such as emission, noise and efficiency levels. In particular, the installation of traditional open chamber boilers will only be possible to replace old boilers installed in multi-family buildings which discharge the fumes into branched collective flues (CCR). Products placed on the market before 09/26/2015 that do not comply with the requirements of the new directive, such as traditional forced draft boilers and boilers not equipped with a high efficiency pump, can still be purchased, sold and installed. ErP and ELD: what do they mean and how are they different? ErP : The EU has issued new obligations for Energy Using Products (ErP). The new directive, known as the Ecodesign directive, prescribes minimum efficiency requirements and emission limits for appliances that produce heating and domestic hot water. The Ecodesign directive is aimed at two categories of products relevant to installers and resellers in the sector: - Category 1 includes space heating appliances; in particular: electrical, gas and diesel appliances such as boilers, heat pumps and cogenerators. - Category 2 Includes appliances for the production of domestic hot water: electric, gas, diesel such as water heaters, heat pumps for DHW, solar systems up to 400 kW and boilers up to 2000 litres. ELD: in addition to the ErP directive, the EU has also introduced mandatory energy labeling for the same type of appliances up to 70 kW and boilers up to 500 litres. The energy labeling directive is called ELD and requires that new products and systems for heating and the production of domestic hot water are labeled with an indication of their energy efficiency class. By combining the products and components, for example by adding a temperature control unit, the energy classification of the system can be increased, which will be calculated by the installer and indicated on the package label. When and how will the new rules apply? On 26 September 2015 the new rules will come into effect. Until then, neither manufacturers, retailers or installers have to comply with the new Ecodesign or labeling provisions. Once the new rules come into effect, manufacturers will only be able to manufacture products that comply with the new Ecodesign requirements, and will be required to supply an energy label with the products What do the new rules mean for the end customer? Unlike household appliances, energy labels on heating and domestic hot water products and systems can only offer a first orientation and will not necessarily provide the best solution for a certain type of installation, nor will they give indications on the assumed cost of energy when obtains a high energy classification. For example, it is not said that a heat pump which presumably will have a higher efficiency class than a condensing boiler can then actually be used in a given type of building. This is why the advice of a competent technician is still necessary to understand the label and select the best product or system that best meets the needs of your building. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€484,00
NB: IN THE ABSENCE OF THE PRODUCT THE FOLLOWING MODEL VMI 35 WILL BE SHIPPED VAILLANT ecoTEC PLUS CONDENSING BOILER VMI 346/5-5 with boiler COMPLETE WITH FUME KIT - ErP METHANE Technical features ErP energy class (Heating and DHW): class A Sanitary load profile - XL For heating and domestic hot water production Forced draft sealed chamber Nominal thermal power in sanitary kW 34 DHW nominal heat input kW 34 Performance stars (according to Dir. 92/42CEE) - **** Consumption at nominal power Natural gas m3 /h 3.7 Expansion vessel capacity 10 l Maximum water content in the system l 180 Storage tank setting temperature °C 35 - 65 Boiler nominal volume l 20 Minimum water flow l/min 1.5 Hot water withdrawal capacity (ΔT = 30K) l/10min 199 Domestic hot water comfort stars (prEN 13203) - *** Dimensions (hxpxl) mm 720x567x440; 59.5kg Power supply V/Hz 230/50 Total electric power W 115 Sound power dBA 49 IP degree of protection IP X4 D NOx class - 5 Version: CNG (0010019531) To view more product information CLICK HERE General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS with boiler Little space and a large family? ecoTEC plus with built-in wall-mounted boiler is the boiler designed to satisfy a high demand for hot water when spaces do not allow for the installation of external boilers. The VMW ecoTEC plus with actoSTOR CL 20 S integrable storage tank are available in power ratings of: 30 and 34 kW. This stratification boiler is a real hot water reserve that can be installed very easily and quickly directly between the wall and the boiler. An exceptional solution that ensures the quantity of water needed is always available and without sudden changes in temperature. The boiler system with storage tank is very simple to assemble: first install the actoSTOR CL wall-mounted storage tank and the related pipes supplied for domestic water, then hang the ecoTEC plus VMW wall-mounted boiler on the storage tank. The dimensions are very small 70cm high, 44cm wide and 55cm deep. The stratification storage tank guarantees the same performance as a storage tank with a 60-litre coil but with considerably reduced spaces. The combination with ecoTEC plus allows you to exclude the storage tank functionality by making the boiler work instantaneously; this allows a considerable saving on gas consumption. New electronics and a very high efficiency pump make ecoTEC plus the wall-mounted condensing boiler that consumes less on the European market. ecoTEC plus is compatible with all Vaillant components and accessories already on the market. The new design is simple and intuitive. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.903,00
LATEST QUANTITIES, CHECK AVAILABILITY IN ADVANCE BY CALLING THE OFFICES Technical features Model : EoTEC Plus VMW 346/5-5+ Code : 0010021994 Power : 34.0 kW Power supply: LPG Forced draft sealed chamber Performance Heating efficiency class: A Sanitary efficiency class: A Sanitary load profile : XL Nominal thermal power in DHW: 34.0 kW Efficiency at 30% : 109.0% Performance Stars : ★★★★ Class : NOx 5 Degree of protection : IP X4 D Expansion vessel capacity: 10 litres Domestic hot water production (ΔT = 30K) 16.2 l/min Power supply (V,Hz, Ø) : 220~240/50/1 Dimensions and weight Dimensions (HxWxD): 720x372x440 mm Weight : 40.0 Kg Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS VMW+ The most efficient and versatile combi condensing boiler there is. ecoTEC plus. Wall-mounted condensing boilers capable of always guaranteeing maximum efficiency and maximum comfort. This is German quality. ecoTEC plus has always been the most popular Vaillant boiler. Today it guarantees even lower consumption, a further increase in efficiency and versatility and the certainty of immediate sanitary comfort without jolts. The best of Vaillant technology to satisfy every need Every component and every function of ecoTEC plus has been designed to combine efficiency and reduced consumption in favor of greater respect for the environment. ecoTEC plus self-adapts to your needs by always choosing the most economical solution, mixing the right amount of gas and air; all this with an electrical consumption of less than 2 Watts (less than half of a radio in operation). The combined version satisfies all comfort needs, guaranteeing both constant hot water without sudden changes in temperature and a comfortable climate. Sanitary comfort, in particular, is managed by the efficient Aqua Comfort pre-heating system which, thanks to 4 probes, controls, verifies and guarantees the immediate delivery of hot water always at the same temperature. Lots of hot water, immediately, without sudden changes is the real comfort offered by ecoTEC plus. From today it can also be installed outdoors where the climate is mild even in winter. In fact, the boiler has a standard antifreeze device which allows it to resist down to -5°C. To have heating and domestic hot water in a single solution The VMW ecoTEC plus condensing wall-mounted boilers combine the production of domestic hot water with the heating function. Unlike all the other boilers, the Vaillant ELGA system is installed inside, which expands the modulation range, but above all electronically regulates and monitors combustion to always ensure the lowest gas consumption, guaranteeing maximum efficiency. The boiler adjusts itself automatically and continuously, as if it were assisted every 30 seconds. In addition to a new, simpler and more intuitive design, the new electronics together with a very high efficiency pump make ecoTEC plus VMW+ the wall-mounted condensing boiler that consumes less on the European market. the ecoTEC plus VMW+ boiler is compatible with all Vaillant components and accessories already on the market. The dimensions are reduced 70cm high, 44cm wide and 35cm deep (identical to the previous version), the weight has been optimized making installation easier. and with vSMART... and go to Class A+ (Optional) All models of the ecoTEC plus VMW+ range have an efficiency etas = 94%. For this reason, if combined with a class VI thermoregulation (such as vSMART), they reach a system efficiency of 98% and therefore the ErP energy class in heating A+. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.872,00€1.788,00
NB: article out of production, in case of unavailability the new model VM 30 CS will be sent VAILLANT ecoTEC PLUS condensing BOILER VMW 306/5-5+ Technical features For heating and domestic hot water production Forced draft sealed chamber Heating efficiency class A Sanitary efficiency class A Sanitary load profile XL Nominal thermal power in DHW 30.0 kW Efficiency at 30% 109.0 Performance stars (Dir. 92/42CEE) **** NOx class 5 Degree of protection IP X4 D Expansion vessel capacity 10 l Domestic hot water production (ΔT = 30K) 14.3 l/min Power supply V/Hz 230/50 Dimensions HxWxD: 720-338-440 mm; 37 kgs Power supply: methane or LPG General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS VMW+ The most efficient and versatile combi condensing boiler there is. ecoTEC plus. Wall-mounted condensing boilers capable of always guaranteeing maximum efficiency and maximum comfort. This is German quality. ecoTEC plus has always been the most popular Vaillant boiler. Today it guarantees even lower consumption, a further increase in efficiency and versatility and the certainty of immediate sanitary comfort without jolts. The best of Vaillant technology to satisfy every need Every component and every function of ecoTEC plus has been designed to combine efficiency and reduced consumption in favor of greater respect for the environment. ecoTEC plus self-adapts to your needs by always choosing the most economical solution, mixing the right amount of gas and air; all this with an electrical consumption of less than 2 Watts (less than half of a radio in operation). The combined version satisfies all comfort needs, guaranteeing both constant hot water without sudden changes in temperature and a comfortable climate. Sanitary comfort, in particular, is managed by the efficient Aqua Comfort pre-heating system which, thanks to 4 probes, controls, verifies and guarantees the immediate delivery of hot water always at the same temperature. Lots of hot water, immediately, without sudden changes is the real comfort offered by ecoTEC plus. From today it can also be installed outdoors where the climate is mild even in winter. In fact, the boiler has a standard antifreeze device which allows it to resist down to -5°C. To have heating and domestic hot water in a single solution The VMW ecoTEC plus condensing wall-mounted boilers combine the production of domestic hot water with the heating function. Unlike all the other boilers, the Vaillant ELGA system is installed inside, which expands the modulation range, but above all electronically regulates and monitors combustion to always ensure the lowest gas consumption, guaranteeing maximum efficiency. The boiler adjusts itself automatically and continuously, as if it were assisted every 30 seconds. In addition to a new, simpler and more intuitive design, the new electronics together with a very high efficiency pump make ecoTEC plus VMW+ the wall-mounted condensing boiler that consumes less on the European market. the ecoTEC plus VMW+ boiler is compatible with all Vaillant components and accessories already on the market. The dimensions are reduced 70cm high, 44cm wide and 35cm deep (identical to the previous version), the weight has been optimized making installation easier. and with vSMART... and go to Class A+ (Optional). All models of the ecoTEC plus VMW+ range have an efficiency etas = 94%. For this reason, if combined with a class VI thermoregulation (such as vSMART), they reach a system efficiency of 98% and therefore the ErP energy class in heating A+. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.749,00
NB: in the absence of the product, the new VMW 26 CS model will be shipped VAILLANT ecoTEC PLUS condensing BOILER VMW 256/5-5+ Technical features For heating and domestic hot water production Forced draft sealed chamber Heating efficiency class A Sanitary efficiency class A Sanitary load profile XL Nominal thermal power in DHW 25.0 kW Efficiency at 30% 110.0 Performance stars (Dir. 92/42CEE) **** NOx class 5 Degree of protection IP X4 D Expansion vessel capacity 10 l Domestic hot water production (ΔT = 30K) 11.9 l/min Power supply V/Hz 230/50 Dimensions HxWxD: 720-338-440 mm; 36 kgs Power supply: Natural gas or LPG (Supplied with convertible natural gas through the assistance centre) General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS VMW+ The most efficient and versatile combi condensing boiler there is. ecoTEC plus. Wall-mounted condensing boilers capable of always guaranteeing maximum efficiency and maximum comfort. This is German quality. ecoTEC plus has always been the most popular Vaillant boiler. Today it guarantees even lower consumption, a further increase in efficiency and versatility and the certainty of immediate sanitary comfort without jolts. The best of Vaillant technology to satisfy every need Every component and every function of ecoTEC plus has been designed to combine efficiency and reduced consumption in favor of greater respect for the environment. ecoTEC plus self-adapts to your needs by always choosing the most economical solution, mixing the right amount of gas and air; all this with an electrical consumption of less than 2 Watts (less than half of a radio in operation). The combined version satisfies all comfort needs, guaranteeing both constant hot water without sudden changes in temperature and a comfortable climate. Sanitary comfort, in particular, is managed by the efficient Aqua Comfort pre-heating system which, thanks to 4 probes, controls, verifies and guarantees the immediate delivery of hot water always at the same temperature. Lots of hot water, immediately, without sudden changes is the real comfort offered by ecoTEC plus. From today it can also be installed outdoors where the climate is mild even in winter. In fact, the boiler has a standard antifreeze device which allows it to resist down to -5°C. To have heating and domestic hot water in a single solution The VMW ecoTEC plus condensing wall-mounted boilers combine the production of domestic hot water with the heating function. Unlike all the other boilers, the Vaillant ELGA system is installed inside, which expands the modulation range, but above all electronically regulates and monitors combustion to always ensure the lowest gas consumption, guaranteeing maximum efficiency. The boiler adjusts itself automatically and continuously, as if it were assisted every 30 seconds. In addition to a new, simpler and more intuitive design, the new electronics together with a very high efficiency pump make ecoTEC plus VMW+ the wall-mounted condensing boiler that consumes less on the European market. the ecoTEC plus VMW+ boiler is compatible with all Vaillant components and accessories already on the market. The dimensions are reduced 70cm high, 44cm wide and 35cm deep (identical to the previous version), the weight has been optimized making installation easier. and with vSMART... and go to Class A+ (Optional). All models of the ecoTEC plus VMW+ range have an efficiency etas = 94%. For this reason, if combined with a class VI thermoregulation (such as vSMART), they reach a system efficiency of 98% and therefore the ErP energy class in heating A+. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.597,00
