NB: in the absence of the ciao at, the NEW CIAO AT 25 LN LOW NOX model will be sent BERETTA CIAO AT 25 CSI CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP Product code: 20113788 Characteristics: Energy efficiency in heating: B Energy efficiency Sanitary: A Sanitary load profile: XL Nominal heat input: 25 kW Electric Power: 129W Supply voltage/frequency: 230/50 Volt/Hz Electrical protection degree: X5D ip Dimensions HxWxD: 780 x 400 x 338 ; 40 Kg Gas version available: METHANE Warm-up exercise: Maximum pressure and temperatures: 3/90 bar/°C Heating temperature selection range: 40/80 °C Pump: pump head available for the system: 266 m/bar Expansion tank capacity: 8 l Healthcare exercise: Maximum pressure: 6 bars Minimum pressure: 0.15 bar Quantity of hot water with ∆t=25°C: 14.3 l/min Minimum domestic water flow rate: 2 l/min DHW temperature selection range: 37 - 60 °C Beretta HELLO AT Hi AT, ideal for replacement in systems with radiators. Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving. High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger. Management: The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. The Ciao AT technology makes use of the condensing exchanger which recovers the latent heat of the fumes, the same principle used by condensing boilers. The exchanger, located at the top left, is connected directly to the fan which pushes the fumes inside it, before they are definitively expelled. The difference in the temperature of the fumes between the ~140°C inlet and the ~65°C outlet of the condensing exchanger is indicative of the amount of heat recovered from them. The return from the system first passes through the condensing exchanger which recovers the heat from the fumes, and then passes through the primary exchanger, where it receives the remaining heat in order to reach the required flow temperature. The water then recovers part of the heat from the fumes, which would otherwise be expelled into the atmosphere, thus giving rise to less waste and consequently greater savings for the user. Outdoor installation: Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board anti-freeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required. Up to 17 meters of Ø 60 ducting with the Ciao AT boiler: With Ciao AT it is possible to comfortably duct even the most "difficult" flues thanks to the approval for Ø 60mm flue systems which is added to the traditional Ø 80 mm ducting flue system. The main 60mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. TECHNICAL FEATURES: Specific for systems with radiators and radiators (at high temperature) Condensing post exchanger in aluminum alloy Possibility of outdoor installation with antifreeze heater kit (optional) IPX5D electrical protection degree Environmental Self-Regulation System (SARA) Low consumption circulator 6 m (EEI≤0.20) Hydraulic connections cover (optional) Condensate collection neutralizer drawer kit (optional) Template, hydraulic fittings, gas and sanitary taps (optional) For gas conversion, contact authorized Beretta Technical Assistance Centres Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENZIONE IL PRODOTTO È NUOVO E FUNZIONANTE MA PRESENTA UN'AMMACCATURA SULLA PARTE FRONTALE E L'IMBALLO È USURATO (PER MAGGIORI INFORMAZIONI SUI DANNEGGIAMENTI VISUALIZZA LE FOTO ACCANTO ALL'IMMAGINE PRINCIPALE). Caldaia Beretta CIAO X 25 C a condensazione low NOx 6 completa di kit scarico fumi GPL - ErP cod. 20197877 Wi-Fi Optional Caratteristiche Tecniche Codice: 20197875 Specifiche etichetta energetica secondo direttiva Europea ErP Classe di efficienza energetica stagionale del riscaldamento A Classe di efficienza energetica del sanitario A Portata termica riscaldamento (max-min) 20,0 - 3,1 kw Portata termica ACS nominale (max-min) 25,0 - 3,1  kw Tensione di alimentazione V-Hz 230 - 50 Grado di protezione IP IPX5D Classe NOx 6 Alimentazione GPL RISCALDAMENTO Pressione-temperatura max bar-°C 3-90 Vaso d’espansione a membrana l 8 SANITARIO Pressione max bar 8 Produzione ACS a ?T= 25 °C / 30 °C / 35 °C l/min 14,3/11,9/10,2 Portata ACS minima l/min 2 DIMENSIONI, PESO Dimensioni caldaia (AxLxP) mm 700x400x275  CIAO X, il comfort che ti meriti CIAO, UNA DELLE CALDAIE MURALI PIÙ VENDUTE DI SEMPRE NEL PORTAFOGLIO BERETTA, È STATA COMPLETAMENTE RIPROGETTATA, DANDO VITA AD UNA NUOVA GAMMA A CONDENSAZIONE CON MOLTE CARATTERISTICHE E VANTAGGI INNOVATIVI: CIAO X La nuova gamma Beretta conserva le caratteristiche distintive degli omonimi modelli precedenti in termini di affidabilità e semplicità di utilizzo, aggiungendone molte altre, importanti e innovative: dal nuovo scambiatore primario in acciaio inox, all'innovativa interfaccia touchpad fino alle connessioni idrauliche con standard DIN.Con CIAO X, Beretta potenzia la ricerca di comfort e innovazione nel rispetto dell'ambiente, che rappresenta uno dei punti di forza delmarchio, a partire dalle origini. Questa rinnovata consapevolezza energetica si traduce in alta efficienza, bassi consumi e un elevato rapporto di modulazione (1:8), che uniti alla flessibilità di installazione, alle dimensioni compatte e al peso contenuto, consentono di collocare CIAO X ai vertici della sua categoria. Ma c'è di più. CIAO X guarda avanti per le generazioni future. La nuova gamma può giàprocessare una miscela di idrogeno fino al 20%, la fonte di energia sostenibile che costituirà la vera svolta ecologica dei prossimi anniLA GAMMACiao X è disponibile in una gamma completa di 5 modelli, per soddisfare le varie esigenze diriscaldamento: CIAO X 25 C (combinata, con codici dedicati per metano e GPL) CIAO X 30 C (combinata) CIAO X 15 R (solo riscaldamento) CIAO X 25 R (solo riscaldamento) Le dimensioni compatte e il peso ridotto di CIAO X ne consentono l'installazione praticamente ovunque all'interno dell'abitazione, anche anche in un pensile in cucina. Il prodotto può essere installato anche all'esterno dell'abitazione (a incasso in BOX o in luogo parzialmente protetto). CONTROLLA IL TUO COMFORT CON UN TOUCHUna delle caratteristiche distintive della nuova CIAO X è l'interfaccia digitale touchpad, che coniuga design e innovazione con la facilità d'utilizzo. Con un semplice touch su 7 punti del pannello, è possibile accedere in modo intuitivo a tutte le impostazioni e aiparametri della caldaia e dell'impianto. Ad ogni touch si attiva un buzzer, che genera un feedback acustico a conferma dell'operazione.Il display LCD comunica con l'utente e l'installatore attraverso icone, senza utilizzare testi, al fine di consentire una comprensione immediata della funzione visualizzata.OVUNQUE CIAO X Le linee morbide ed essenziali dell'innovativo controllo touch conferiscono a CIAO X un carattere moderno e gradevole, che facilita l'integrazione in ogni contesto. Le dimensioni compatte e il peso contenuto permettono alla caldaia di essere facilmente installatapraticamente ovunque, non solo all'interno dell'abitazione, ma anche all'esterno (a incasso in box o in luogo parzialmente protetto). CIAO X è quindi ideale per la sostituzione di vecchie caldaie, sia con sequenza di connessioni DIN che Beretta, grazie alla disponibilità di kit accessori che ne semplificano la conversione.Un'ampia gamma di accessori completa l'offerta di CIAO X: kit fumi, filtri acqua compatti (addolcitore e magnetico) e copertura delle connessioni idrauliche, facilitandone l'installazione e armonizzandone l'integrazione, sia in ambienti indoor che outdoor. NUOVO SCAMBIATORE A CONDENSA ZIONE IN ACCIAIO INOXCIAO X è dotata di un nuovo scambiatore primario in acciaio INOX, con tubo liscio ad elevata sezione, per assicurare ottima efficienza e pulizia nel tempo. L’acciaio INOX, oltre all’elevata resistenza all’azione corrosiva della condensa acida, previene la formazione interna di ossidi e di altri fenomeni elettrochimici tipici in installazione su vecchi impianti. La geometria a spira unica avvolta (circuito idraulico in serie) assicura portata costante in tutte le sezioni dello scambiatore e previene intrinsecamente fenomeni di intasamento. L’accesso frontale agevola le operazioni periodiche di manutenzione e pulizia della camera di combustione NUOVE FUNZIONI PER UN MAGGIORE COMFORT IN SANITARIONei modelli combinati, lo scambiatore a piastre ad alto rendimento, collegato al circuito primario dell'acqua calda, permette di riscaldare l'acqua sanitaria in modo istantaneo, senza la necessità di un bollitore esterno. Il nuovo scambiatore sanitario è stato ottimizzato da Beretta per ottenere prestazioni elevate e massimo comfort per l'utente finale in termini di stabilità della temperatura e ridotti tempi di attesa. Questi plus, che pongono CIAO X ai vertici della categoria di riferimento, si traducono in ultima analisi in risparmio idrico ed energetico, per un maggior rispetto dell'ambiente.Ecco alcune tra le funzioni speciali di CIAO X: La funzione PRERISCALDO e la sua evoluzione in PRERISCALDO SMART sono state concepite per ridurre ulteriormente i consumi di acqua e gas. Queste funzioni permettono, infatti, di mantenere calda l'acqua all'interno del nuovo scambiatore a piastre ad alta efficienza, prodotto nei nostri stabilimenti, riducendo nel contempoo i tempi di attesa. La funzione TOUCH & GO permette di attivare un preriscaldo istantaneo, solo per una richiesta specifica. Altre funzioni speciali come RITARDO SANITARIO, ANTI-OSCILLAZIONE, VENTILATORE SMART permettono di migliorare le prestazioni della caldaia in condizioni di funzionamento particolarmente difficili, come ad esempio nel caso di temperatura dell'acqua in ingresso molto bassa o molto alta, o una portata d'acqua molto bassa HI, COMFORT IL TUO COMFORT A PORTATA DI MANO CIAO X* È COMPATIBILE CON HI, COMFORT, LA NUOVA PIATTAFORMA DI SOLUZIONI IOT DI BERETTA, CHE PERMETTE DI GESTIRE IL COMFORT IN MANIERA SEMPLICE E INTUITIVA L’utente finale può gestire il clima di casa con il tradizionale controllo con termostato HI, COMFORT T100, tramite la nuova App HI, COMFORT, che si può connettere al termostato attraverso Wi-Fi box. La nuova App è scaricabile gratuitamente per i sistemi Android e iOS e permette di monitorare gli stati, impostare da remoto la temperatura dell’acqua calda sanitaria e definire i setting della caldaia in modosemplice e sicuro. Inoltre, installare HI, COMFORT T100 è facile e veloce e, in caso di sostituzione di un vecchio termostato,non necessita di interventi sull’impianto elettrico dell’abitazione. HI, COMFORT T100, alimentato a batteria, permette anche l’installazione “senza fili”, se si dota l’impianto di un ricevitore in radiofrequenza SMART KEY K100 La nuova gamma CIAO X nasce predisposta per la Smart Key K100, un accessorio pensato per le caldaie a condensazione Beretta di ultima generazione, che segna la loro evoluzione verso un comfort sempre più eco-sostenibile. La Smart Key K100, attraverso l’Appproprietaria HI, COMFORT, permette di conoscere lo stato di funzionamento della caldaia, modificarne i parametri e tanto altro, il tutto da remoto. Di sicuro interesse per l’utente le diverse funzioni della Smart Key K100: dalla “Funzione Biberon”, per proteggere bambini e utenti non autosufficienti dal rischio di scottature, alla “Funzione Booster”, per massimizzare la velocitàdi riscaldamento dell’ambiente, fino alla “Funzione Benessere”, per mantenere una temperatura dell’acqua calda costante per il massimo comfort e altre ancora, tutte da scoprire. E per l’utente sempre più attento all’ambiente, è possibile, attraverso l’App HI, COMFORT, monitorare e gestire l’utilizzo di energia del proprio sistema di riscaldamento, arrivando a risparmiare fino al 15%* deiconsumi ed evitando inutili sprechi. Per un futuro sostenibile CIAO X nasce già predisposta per funzionare con miscele di gas naturale e idrogeno - fino a un massimo del 20% - una prima importante tappa verso il raggiungimento degli obiettivi di sostenibilità ambientale e il percorso di decarbonizzazione avviato dall’Unione Europea. Disponibilità in enormi quantità Producibilità mediante metodi a basso impatto e in modo sostenibile da fonti rinnovabili, quali l’energia eolica, fotovoltaica e le biomasse Riduzione delle emissioni inquinanti nella percentuale relativa al suo impiego Reale opportunità di cambiamento per avviare il percorso di decarbonizzazione, contrastare il cambiamento climatico globale, migliorare la qualità dell’aria e della vita Garanzia Prodotto : Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. FOR CONVERTING TO LPG, CONTACT THE AUTHORIZED AREA SERVICE CENTER IN ADVANCE Beretta MYNUTE X 25 C Low NOx condensing boiler complete with flue gas kit 20163564 LPG - NEW Boiler code 20163564 Seasonal heating energy efficiency class A Energy efficiency class of the sanitary fixture A Declared load profile XL NOx emission class 6 HEATING EXERCISE Heating thermal capacity (max-min) kW 20.00-3.60 Maximum pressure-temperature bar-°C 3 - 90 Expansion tank capacity l 9 HEALTHCARE EXERCISE Nominal DHW heat input (max-min) kW 25.00-3.60 DHW energy efficiency ηwh % 83 DHW production at ∆T= 25°C / 30°C / 35°C l/min 14.3/11.9/10.2 CONNECTIONS Heating inlet - outlet Ø 3/4” DHW inlet - outlet Ø 1/2” Gas inlet Ø 3/4” DIMENSIONS, WEIGHT Boiler dimensions (HxPxL) mm 740x420x275; 35 kgs MYNUTE X BERETTA PRESENTS MYNUTE X, THE NEW RANGE OF CONDENSING BOILERS, WITH MANY INNOVATIVE AND ADVANTAGEOUS FEATURES From the primary exchanger in stainless steel to the modern electronic interface, there are numerous new elements that distinguish MYNUTE X in the Beretta offer. The new condensing range, with its 5 models from 20 to 35 kW, with "combined" and "heating only" versions, meets every need for residential comfort. High efficiency, low consumption and ease of installation make MYNUTE X the winning choice, both for new homes and for the replacement market. With MYNUTE X, the novelty of the project merges with Beretta's tradition of excellence, matured in almost half a century of experience in the home comfort sector. Its aesthetics, in line with the Beretta style of the latest generation products, easily integrates into any living context, thanks also to its compactness and installation flexibility. NEW DIGITAL INTERFACE MYNUTE X is equipped with a modern and user-friendly control panel, elegantly covered by a door that lets you glimpse the light of its "green gem", the LED light bar that signals its current operating status. Through a modern backlit LCD display, which communicates with the user through icons and scrolling texts (multilingual), it is possible to access the functions of MYNUTE X. Through 7 silk-screened operating keys, it is possible to navigate the panel in a simple and intuitive way, accessing to the settings and parameterizations of the boiler and the system. MYNUTE X FEATURES MANAGEMENT OF UP TO 2 HYDRAULIC CIRCUITS, HIGH AND/OR LOW TEMPERATURE, THROUGH SPECIFIC PREHEATING ACCESSORIES PREHEATING ACTIVATION TO REDUCE DOMESTIC HOT WATER WAITING TIMES CLOCK FUNCTION WEEKLY PROGRAMMING INTEGRATED IN THE DISPLAY POSSIBILITY OF CONNECTION WITH DOMESTIC HOT WATER TANK (R MODELS) Technology and benefits NEW PRIMARY EXCHANGER IN STAINLESS STEEL THE NEW MYNUTE X EXCHANGER IS MADE OF STAINLESS STEEL, WITH A HIGH SECTION SMOOTH PIPE TO OFFER THE BEST EFFICIENCY AND CLEANLINESS OVER TIME. In addition to the high resistance to the corrosive action of acid condensate, AISI 304 L stainless steel reduces the internal formation of oxides and other electrochemical phenomena typical of installation on old systems. The single wound coil geometry (hydraulic circuit in series) offers a constant flow rate in all sections of the exchanger and intrinsically limits clogging phenomena. Front access facilitates periodic maintenance and cleaning of the combustion chamber. INTEGRATED CLAP MYNUTE X is C10 * approved (formerly 3CEp approved), integrating the non-return valve (clapet) as standard on all models, which makes it "ready to install" in case of installations in pressurized collective flues, for which the non-return valve is a mandatory device. The non-return valve is a specific device which allows the combustion fumes to flow through the ducts in only one direction, i.e. from the burner to the flue gas outlet. Its function is therefore to prevent the fumes from returning to the combustion chamber, compromising the correct functioning of the boiler. This could happen for various reasons, for example in the event of overpressure in the duct of a collective flue system. The non-return valve is generally supplied as a specific optional kit, to be installed at the flue outlet of a boiler in the case of C10 type collective exhausts. In MYNUTE X the non-return valve is positioned inside the boiler (see detail), which translates into quick installation and cost reduction. HYBRID READY MYNUTE X is a HYBRID READY solution. The boiler was born within the offer of HYBRID READY products, which make up the new hybrid technology system conceived and developed in the Beretta Research Laboratories. This system, created to meet the current and future integration and management needs of the various energy sources (Gas/Electricity/Renewables), also includes the most innovative methods of energy accumulation and distribution. Characteristics INNOVATIVE STAINLESS STEEL CONDENSING HEAT EXCHANGER WITH FRONT ACCESS WIDE MODULATION RANGE (UP TO 1:8) LOW CONSUMPTION MODULATING CIRCULATOR (EEI ≤ 0.20), 6 m EQUIPPED WITH STANDARD FUME CLAP (CHECK VALVE) AND C(10) APPROVED.* LOW POLLUTANT EMISSIONS: CLASS 6 (UNI EN 15502) MYNUTE X IS HYBRID READY: IT WAS BORN TO BE INTEGRATED INTO BERETTA MULTI-ENERGY SYSTEMS THROUGH THE HYBRID REC 10H AND THE HYBRID CONNECTS, AVAILABLE AS ACCESSORIES INSTALLATION FLEXIBILITY: INDOOR, OUTDOOR** AND RECESSED*** INSTALLATION (IN A PARTIALLY PROTECTED PLACE) CLICK-FIT FLUE CONNECTION: FAST AND SAFE, WITHOUT THE NEED OF AN EXTERNAL COLLAR ANTIFREEZE RESISTANCE KIT, HYDRAULIC CONNECTIONS AND EXTERNAL PROBE AVAILABLE AS ACCESSORIES ELECTRICAL PROTECTION DEGREE IPX5D SUPPLIED "DOUBLE T" TEMPLATE COMPATIBLE WITH HYBRID CONNECTORS FOR THE MANAGEMENT OF UP TO TWO SYSTEM ZONES FOR GAS CONVERTING, PLEASE CONTACT AUTHORIZED BERETTA TECHNICAL ASSISTANCE CENTERS COMPATIBLE WITH BeSMART WIFI COMFORT CONTROL AS THERMOSTAT (OTBUS COMMUNICATION), ALLOWING THE MOST ADVANCED FUNCTIONS POSSIBILITY OF INTUBATING FLUES WITH THE SPECIFIC FLUE IN PP Ø60 AND Ø50 Product Warranty The warranty on this item is 24 months from the date of purchase.

Read more less

Beretta CIAO AT 29 csi LOW NoX condensing boiler Complete with smoke kit Cod. 20151830 Technical specifications according to ErP directives Model: HELLO AT LOW NOx Sanitary energy efficiency class: A Energy efficiency class in heating: B Load profile: XL Product code 20151830 Natural gas supply Technical features: Indoor/Outdoor installation Nominal heat input 28 kW Nominal thermal power 26.8 kW Nominal thermal power at partial load (30%) 8.5 kW Useful efficiency at nominal power 86.3% n4 New version NOx < 56 mg/kWh IPX5D electrical protection degree Dimensions Dimensions h/w/d (mm): 780/452/336 NB: THE BOILER IS SUPPLIED WITH METHANE, IT CAN BE CONVERTED TO LPG THROUGH THE AREA ASSISTANCE CENTER HELLO AT new LOW NOx model Hi AT, ideal for replacement in systems with radiators Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving. New burner with low NOx emissions Specific for systems with radiators and radiators (at high temperature) Condensing post exchanger in aluminum alloy Possibility of outdoor installation with antifreeze heater kit (optional) IPX5D electrical protection degree Environmental Self-Regulation System (SARA) Low consumption circulator 6 m (EEI≤0.20) Hydraulic connections cover (optional) Condensate collection neutralizer drawer kit (optional) Template, hydraulic fittings, gas and sanitary taps (optional) High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger. The management The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. Compatible with BeSMART The BeSMART WiFi Comfort Control Panel, optional compatible with Ciao AT, is the remote boiler management device with modulating chronothermostat functions. With the WiFi Box accessory, included in the BeSMART WiFi Comfort Control, it is also possible to manage comfort remotely using Smartphones and Tablets. The BeSMART WiFi control is very simple to install and intuitive to use and allows you to adjust the parameters and activate the many functions on the boiler. A large liquid crystal display shows all important information. Using the buttons on the control, the temperature of the heating water and domestic hot water is set easily and intuitively and the heating time programming is carried out. Outdoor installation Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board antifreeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

Energy label specifications according to the European directive ErP: Heating energy efficiency: Class A XL profile DHW energy efficiency: Class A (EXCLUSIVE plus only the BeSMART Wi-Fi Comfort Control (optional) forms a class A+ system) Characteristics of operation in heating and DHW: Heating thermal capacity kW 24.00 Nominal DHW heat input kW 30.00 Nominal thermal power (80°/60°) kW 23.54 Nominal thermal power (50°/30°) kW 25.56 QHE Annual Power Consumption GJ: 42W Sound power level, within LWA dB 53 NOx emissions: mg/kWh 33 Max heating pressure-temperature: bar-°C 3-90 Diaphragm expansion vessel capacity: 8 l Hot water quantity at: ΔT 25 K / ΔT 30 K / ΔT 35 K l/min 17.2 / 14.3 / 12.3 Electrical protection degree: IP X5D NOx emission class: 6 Dimensions HxWxD:740x420x275 mm; 37kg Power supply: methane NEW EXCLUSIVE EXCLUSIVE, A NEW STORY BEGINS. Through the innovative ACC electronic injection combustion, HYBRID READY integration and the new project design, EXCLUSIVE offers exclusive advantages in every installation variation. From the new EXCLUSIVE, A NEW STORY BEGINS. construction, redevelopment; from hybrid application in a multi-energy system to simple single installation, EXCLUSIVE represents the current and winning choice for those who are not satisfied and want to look beyond. Characteristics: Electronic injection combustion via ACC system EXCLUSIVE plus only the BeSMART Wi-Fi Comfort Control (optional) forms a class A+ system 94% (ETAs) of energy efficiency in heating Universal installation : Indoor, outdoor and recessed installation. IPX5D electrical protection degree Tempozero installation: Removing the casing NO longer necessary for electrical connections and calibration Low consumption modulating circulator (EEI≤ 0.20) 6 m head, electronically modifiable up to 7 m Hydraulic connections and external probe available as options Frost protection down to -5 °C as standard HYBRID READY boiler , Can be integrated via BUS in a multi-energy system to make boiler operation more effective in relation to other energy sources (can be combined with a Beretta hybrid system using the REC 10H interface available as an accessory) Talking display: User interface for direct communication using TEXT and ICONS Self-adapting: The boiler automatically adapts to different types of gas and installation - ZERO calibrations CO alarm Boiler CO level constantly monitored and calibrated for maximum safety Small size: Thanks to its compactness, EXCLUSIVE can also be easily installed in a wall unit LPG version selectable from parameter Gas transformation kit not necessary Europe strategy With the opening towards the management of multi-energy plants, the reduction of emissions and the optimization of consumption, Beretta signs with EXCLUSIVE the highest contribution in terms of respect for the environment, in view of the 20-20-20 objectives of the Union countries expected by 2020, reconfirming their commitment to an increasingly eco-sustainable future.        Exclusive: a milestone in the evolution of Beretta Combustion and electronics, i.e. the heart and brain of EXCLUSIVE, entirely designed in the Research and Development Laboratories of the historic Lecco headquarters, mark a turning point in Beretta's mural evolution and are the result of the spirit of innovation that has distinguished the brand since its origins. With EXCLUSIVE, the novelty of the project fits perfectly into the tradition of know-how and takes on a linear design, which reworks some aesthetic lines of the first boiler models in a modern key, in perfect continuity of style. Continuity that is also manifested in the re-proposition of the EXCLUSIVE name, which has always characterized the top of the Beretta range, with exclusive features and advantages. Class A+ system using only the BeSMART WiFi Comfort Control (optional) .   "talking" interface The control panel is one of the distinctive elements of EXCLUSIVE which confirms its innovative profile. In fact, there are many EXCLUSIVE functions, all to be discovered, through a modern 3.5” backlit LCD display, which communicates with the user through texts and icons. By means of the intuitive silk-screened operating keys it is also possible to access the settings and parameterizations of the boiler and the system. GREEN GEM OF EXCLUSIVE: LED light bar that signals the current operating status of the boiler, reflecting on the casing even with the door closed.   Exclusive Features: HOURLY PROGRAMMING : Programmable heating by hour and by single zone INTELLIGENT SYSTEM FILLING Autonomous filling activation and total safety SYSTEM PRESSURE Displayed DATE AND TIME Display as screensaver PREHEATING Domestic hot water preheating activation SCHEDULED MAINTENANCE Intelligent system that warns the user when boiler maintenance is due   Everywhere Exclusive: Thanks to BeSMART, Beretta's WiFi Comfort Control, controlling and managing home comfort is now possible wherever you are, through a simple and intuitive App, via smartphone and tablet. EXCLUSIVE is compatible with all BeSMART functions, even the most advanced. From home heating professionals, easy management of home comfort. Even away from home   Electronic injection combustion The ACC system, designed and developed by Beretta, allows in all circumstances to offer "first class" functionality, efficiency and low emissions. Using a sensor for detecting the flame ionisation current, which allows the electronics to continuously modulate the quantity of fuel injected, the system keeps the air/gas mixture constant at optimal values ​​over the entire modulation range of the delivered power. Thanks to the ACC system, combustion adjusts itself, thus eliminating the need for any calibration and allowing the boiler to operate with different gas compositions. Particular attention is paid to CO emissions, through a self-diagnosis that intervenes on the burner before the emission threshold allowed by the legislation is exceeded. [A] Cylindrical burner in stainless steel [B] Integrated electronic board [C] Traditional ga valve with modulator [D] Modulating fan with Hall effect     Hybrid Ready EXCLUSIVE is a HYBRID READY solution. The boiler was born as a fundamental element of the offer of HYBRID READY products, which constitute the new hybrid technology system conceived and developed in the Beretta Research Laboratories. This system, created to meet the current and future needs of integration and governance of the various energy sources (Gas/Electricity/Renewables), also includes the most innovative methods of energy accumulation and distribution. EXCLUSIVE, AS A HYBRID READY SOLUTION, IS THE IDEAL CHOICE FOR THOSE WHO WANT TO LOOK AHEAD AND INVEST IN A PRODUCT WHICH WILL MAINTAIN ITS ITS VALUE UNCHANGED OVER TIME. Thanks to the new communication BUS with which it is equipped, EXCLUSIVE is able to interact perfectly with the Energy Manager REC 10H, a real thinking brain that constantly monitors the hybrid system created, to always offer the best comfort in an efficient and effective way. The Beretta hybrid, distinguishing itself for its modular approach to the world of multi-energies, is therefore able to offer increasingly tailored comfort and to evolve over time, with the inclusion of new components that increase efficiency   Beretta is “ERP”. The concrete commitment towards an eco-sustainable future   The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations simultaneously issued for the energy labeling of products will also become effective in addition to the corresponding Directive 2010/30/EU.  The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands.   In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual appliances. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency.   Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

BERETTA MYNUTE SINTHESI 29 CSI CONDENSING BOILER COMPLETE WITH CNG FUME EXHAUST KIT NEW ErP Characteristics: Mynute Sinthesi presents itself in a renewed guise, keeping unchanged all the characteristics that they have always distinguished it. Mynute Sinthesi is the innovative condensing boiler studied specially by Beretta for traditional systems ad high temperature (radiators and radiators). The boiler is equipped with a fume heat recovery unit and combustion in sealed chamber; this allows for obtain very high performance in terms of yield and therefore significant savings energetic. Mynute Sinthesi therefore represents the ideal solution both in the first installation and in the replacement. MYNUTE SINTHESI 29 CIS Class B heating energy efficiency Sanitary energy efficiency Class A Sanitary load profile - XL Seasonal heating efficiency % 86 CHARACTERISTICS Nominal heat input kW 29 Nominal thermal power (80 - 60 °C) kW28.30 Reduced thermal power (80 - 60 °C) kW 14.28 Reduced heat input kW 15 Electric power Watt 114 Electrical protection degree IP X5D X5D Useful efficiency at Pn max ((80 - 60 °C) % 97.6 Useful efficiency at 30% of Pn (47 °C return) % 95.2 HEATING EXERCISE Maximum pressure and temperatures bar/°C 3 / 90 Heating temperature selection range °C 40 / 80 Pump: pump head available for the system mbar 266 at a flow rate of 1000 litres/h Expansion vessel capacity 9 litres HEALTHCARE EXERCISE Maximum pressure 6 bar Minimum pressure bar 0.15 Quantity of hot water with ∆t=25°C litres/min 16.6 Minimum domestic water flow rate litres/mini 2 DHW temperature selection range °C 37 - 60 CONNECTIONS Heating inlet - outlet Ø 3/4” DHW inlet - outlet Ø 1/2” Gas inlet Ø 3/4” COAXIAL FUME EXHAUST AND AIR INTAKE PIPES Diameter mm 60 - 100 Maximum length 4.5 m Loss for inserting a 90° / 45° bend m 1.6 / 1.3 Diameter mm 80 - 125 Maximum length 11m 9 Loss for inserting a 90° / 45° bend m 1.5/1 SEPARATE FUME EXHAUST AND AIR INTAKE PIPES Diameter mm 80 + 80 80 + 80 Maximum length m 12 + 12 Loss for inserting a 90° / 45° bend m 1.5/1 DIMENSIONS, WEIGHT, GAS Boiler size (HxLxP) mm 780x452x338 Weight kg 44 Gas versions available (*) MTN (*) For gas conversion, contact authorized Beretta Technical Assistance Centres General characteristics Mynute Sinthesi - ErP Mynute Sinthesi by Beretta is a wall-mounted condensing boiler for high temperature single-family systems. Continuous electronic modulation of the gas antifreeze device as standard (up to 0°C). Environmental Self-Regulation System (SARA). Mynute Sinthesi keeps all the peculiarities of the Mynute range unchanged but evolves towards new needs. The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this makes it possible to obtain very high performance in terms of efficiency and therefore significant energy savings. Mynute Sinthesi therefore represents the ideal solution both in the first installation and in the replacement. Product Guarantee The warranty on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. FOR CONVERTING TO LPG, CONTACT THE AUTHORIZED AREA SERVICE CENTER IN ADVANCE Energy label specifications according to the European ErP directive   Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal heat input: 25 kW Nominal heat output: 24.38 kW Classification European Directive EEC 92/42: **** Efficiency at rated power: 99.7% Efficiency at reduced load (30%): 109.4% Total electric power: 88W Quantity of hot water with Δt=25°C: 14.3 l/min Dimensions (hxwxd) mm 890x553x275; 44kg Standard antifreeze down to -15°C Standard Built-in antifreeze system (SAI) METHANE power supply Legend: HE (Hi Efficiency) C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control) AG (antifreeze (-15°C). Weather Green E (Hi Efficiency) Beretta boilers offer reliability and excellent technology, such that they can be used in solar thermal systems and in systems with the most recent and innovative technologies. Beretta presents Meteo Green e , the new range of outdoor and built-in condensing boilers designed to offer high energy efficiency. The boiler is in fact equipped with a wide modulation range (1:10), range rated approval, low consumption circulator (class A) with variable speed and all the advantages of the Meteo range.   Condensing exchanger : Designed to provide high performance in compliance with the strictest European directives in terms of energy efficiency and low emissions. The innovative condensing exchanger and the production process have allowed Beretta to file an application for a European Patent (Patent Pending). The exchanger is born in a single aluminum tube and without welding. The high thermal conductivity of aluminum allows for a more uniform distribution of temperature so as not to create overheating points for the benefit of greater durability of the exchanger. Furthermore, aluminum offers a high resistance to corrosion. The single pipe architecture (series circuit) allows to obtain a large section for the passage of water in the exchanger with the advantage of having low pressure drops and preventing both the deposit of limescale and impurities The innovative aluminum condensing exchanger allows you to recover a large part of the heat of the fumes by reducing losses to the chimney, and a large part of the latent heat of condensation of the water vapor present in the fumes, reaching a four-star energy efficiency value (according to European Directive EEC 92 /42). The exchanger is born in a single aluminum tube and without welding.  Modulation 1:10 The range offers a wide range of modulation to respond to real energy needs, while simultaneously offering high reduction of consumption. Beretta realizes this system through a totally pneumatic and therefore safe and reliable model. The electronics in fact act only on the number of revolutions of the fan (inlet air flow rate) without intervening on the injection of the quantity of gas which is automatically aspirated. Beretta therefore introduces a new double distribution mixer: a mechanical damper with a calibrated weight that opens or closes a part of the venturi section in order to divide the modulation range into two stages (smaller section with low air flow or larger section with high air flow rates). Beretta has also developed a specific silencer in the air intake to reduce any resonances generated by the new mixer.   Low consumption modulating circulator (Class A) It reduces electricity consumption by up to 60%, thanks also to self-adaptation in proportion to the power supplied or to operation at constant ΔT. Thanks to the new technology adopted, the electric motor of the circulator offers an Energy Efficiency Index EEI<0.23, which means considerably reduced electricity consumption and already in line with energy saving requests. The new low consumption modulating circulator (class A) offers technologically advanced control and allows a high reduction in consumption thanks also to the modulation in a wide range of flow rates. Comfort Technological innovation combined with advanced electronics allow obtaining the "Three stars" in sanitary comfort: the maximum foreseen by Pr EN 13203. Intelligent Management Meteo Green he is equipped with Easy Climate function (standard temperature control with external probe) and Remote Control Panel (REC07) with Easy Filling function (system filling that can be activated from the remote control), (only csi model).  Characteristics: Modulation 1:10 Low consumption modulating circulator (Class A): self-adaptation in proportion to the power supplied or operation at constant DELTA T, (EEI<0.23) RANGE RATED certification which allows you to adjust the heat input of the boiler to the actual needs of the system Performance 4 STARS according to European Directive EEC 92/42 Efficiency at 100% Pn > 93+2 log Pn according to DL 311/06 Low polluting emissions: class 5 according to UNI EN 483 Patented condensing exchanger (Patent Pending) in aluminum with high flow rate Sanitary comfort 3 STARS: the maximum required by Pr EN 13203 Thermoregulation with standard external probe REC 07 remote control panel as standard Standard antifreeze protection down to -15°C (mod. AG) IPX5D electrical protection degree For gas transformation, contact the Assistance Centres Authorized Beretta technique   Beretta is “ERP”. The concrete commitment towards an eco-sustainable future   The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations simultaneously issued for the energy labeling of products will also become effective in addition to the corresponding Directive 2010/30/EU.  The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands.   In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual devices. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with a nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency.   Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less

ATTENTION THE BOILER IS SUPPLIED WITH METHANE. FOR CONVERTING TO LPG, CONTACT THE AUTHORIZED AREA SERVICE CENTER IN ADVANCE Beretta CIAO AT 29 csi LOW NoX condensing boiler Complete with smoke kit Cod. 20151830 Technical specifications according to ErP directives Model: HELLO AT LOW NOx Sanitary energy efficiency class: A Energy efficiency class in heating: B Load profile: XL Product code 20151830 LPG supply Technical features: Indoor/Outdoor installation Nominal heat input 28 kW Nominal thermal power 26.8 kW Nominal thermal power at partial load (30%) 8.5 kW Useful efficiency at nominal power 86.3% n4 New version NOx < 56 mg/kWh IPX5D electrical protection degree Dimensions Dimensions h/w/d (mm): 780/452/336 HELLO AT new LOW NOx model Hi AT, ideal for replacement in systems with radiators Ciao AT is the innovative condensing boiler specifically designed by Beretta for traditional high temperature systems (radiators and radiators). The boiler is equipped with a heat recovery unit on the fumes and combustion in a sealed chamber; this allows to obtain very high performance in terms of efficiency and therefore a significant energy saving. New burner with low NOx emissions Specific for systems with radiators and radiators (at high temperature) Condensing post exchanger in aluminum alloy Possibility of outdoor installation with antifreeze heater kit (optional) IPX5D electrical protection degree Environmental Self-Regulation System (SARA) Low consumption circulator 6 m (EEI≤0.20) Hydraulic connections cover (optional) Condensate collection neutralizer drawer kit (optional) Template, hydraulic fittings, gas and sanitary taps (optional) High performance and low consumption In the Ciao AT boiler, the water in the primary circuit passes through an additional exchanger, which allows you to recover energy that would otherwise be wasted. This process makes it possible to recover latent heat and therefore to further increase the performance of the boiler. The energy saving offered by a boiler is greater the higher its efficiency: Ciao AT therefore allows you to reduce gas consumption compared to a boiler without an additional exchanger. The management The electronic panel is the interface for managing the boiler. Simple and intuitive, it allows you to adjust the boiler parameters and activate the numerous functions. The liquid crystal display provides information on the status of the device and the diagnostic codes. By turning the knobs, the heating water and domestic hot water temperature can be set easily and intuitively. The panel integrates the Sistema Clima Amico function. Compatible with BeSMART The BeSMART WiFi Comfort Control Panel, optional compatible with Ciao AT, is the remote boiler management device with modulating chronothermostat functions. With the WiFi Box accessory, included in the BeSMART WiFi Comfort Control, it is also possible to manage comfort remotely using Smartphones and Tablets. The BeSMART WiFi control is very simple to install and intuitive to use and allows you to adjust the parameters and activate the many functions on the boiler. A large liquid crystal display shows all important information. Using the buttons on the control, the temperature of the heating water and domestic hot water is set easily and intuitively and the heating time programming is carried out. Outdoor installation Ciao AT is designed to also be installed outdoors in partially protected places thanks to the dedicated accessories (bottom cover kit and top cover kit) and board antifreeze protection down to 0 °C. In colder temperatures it is possible to extend the protection down to -10 °C using the special antifreeze heater kit with which the lower cover is required. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.

Read more less

  Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Seasonal heating efficiency % 94       Characteristics of heating/DHW operation: Heating/DHW nominal heat input: 20/25 kW Heating nominal heat output: 19.64 kW Efficiency at rated power: 98.2% Efficiency at reduced load (30%): 103.4% Max electric power heating Watt 80 Electrical protection degree IP X5D Expansion vessel capacity 8 litres Quantity of hot water with Δt=25°C: 14 l/min Minimum domestic water flow rate: 2 l/min Dimensions (hxlxp) mm 780x400x365 ; 38kg METHANE power supply Legend: C (heating + sanitary water) S (sealed chamber) I (electronic ignition, ionisation control) Mynute Green E - ErP   System energy class A+ (in combination with external probe and Rec 08 remote panel) Heating energy class A Energy class of the sanitary A New condensing exchanger Modulation 1:5 Flex low consumption circulator (IEE≤0.20) Ducting with flue Ø 50 mm  The new Mynute Green E range is designed following the ecodesign indications provided for by the European ErP Directive and is made up of two combined models and a heating only model. The combined versions have a thermal capacity of 20-25 kW and 25-30 kW, values ​​which refer respectively to heating and DHW; similarly, the heating only version has a thermal capacity of 25-30 kW. The range offers as standard the new front access condensing exchanger with improved efficiency (94% seasonal efficiency), the low consumption modulating circulator, the predisposition for the clapet kit (optional) to be used for pressurized flues and the high pressure fan. prevalence to be able to carry out the ducting of flues with Ø 60 or Ø 50 exhausts. Mynute Green E: high energy efficiency, low gas consumption and low emissions. The entry into force of the European Directive ErP (26.09.2015) provides that even generators for the production of heating and domestic hot water are classified through the appropriate energy label indicating the class. Compulsory labeling provides greater transparency on the characteristics of the products which can be easily compared, helping the user to find those with greater efficiency. Consequently, even with boilers it will be easier to contribute to the achievement of the "20-20-20" objective set for the year 2020 which consists of: reducing greenhouse gas emissions (CO2 ) by 20%, increasing by 20 % use of renewable energies and reduce energy consumption by 20% in EU countries. The new Beretta condenser exchanger with front access The Mynute Green E boiler is equipped with the new Beretta condensing exchanger with front access. An innovative system of guides allows it to move like a drawer, making disassembly for cleaning required by current regulations much faster. Continuous research has allowed Beretta to obtain an exchanger characterized by a considerable increase in performance: 94% average seasonal efficiency calculated according to the European ErP Directive. The exchanger comes from a single aluminum tube, without welding thanks to an innovative production process. The high thermal conductivity of aluminium, much higher than that of steel, allows for greater uniformity in temperature distribution. The single pipe architecture (series circuit) allows for a large section for the passage of water with the advantage of reducing pressure drops and preventing the deposit of impurities, keeping the exchanger performing over time. With the new Beretta condensing exchanger, boiler performance improves up to an average seasonal efficiency of 94%. Mynute Green E, the elegant The new Mynute Green E is characterized by a particularly elegant aesthetic and is equipped with a simple and intuitive digital display which makes information on the status of the appliance immediately usable. The modern ergonomic knobs allow you to easily select all the functions necessary for using and setting the boiler. Flex modulating circulators: optimized performance, low consumption Mynute Green E uses a synchronous modulating circulator with low energy consumption, as required by the European ErP Directive. Thanks to this new technology, the electric motor of the circulator offers an Energy Effi ciency Index of less than 0.20, which means significantly reduced electricity consumption. The new circulator works proportionally to the power supplied by the boiler, thus contributing to a further reduction in electricity consumption. In case of need on the heating system, it is possible to change the head without having to replace the standard circulator with a high head one, the name “Flex” derives from this feature. Up to 49 meters of ducting With Mynute Green E it is possible to comfortably intubate even the most "difficult" flues thanks to the approval for flue Ø 50mm. The main 50mm flue ducts are available in the Beretta price list catalogue, while the boiler manuals provide indications of the maximum length, which differ according to the boiler power. Characteristics: MYNUTE GREEN E + external probe + REC 08 remote control forms a class A+ system Designed according to the ecodesign indications provided for by the European ErP Directive Energy Class > heating (class A) > DHW profile XL (class A) Seasonal heating efficiency 94% Low polluting emissions: class 5 (UNI EN 483) New high-flow aluminum condensing exchanger with front access Standard thermoregulation (optional external probe) ErP boilers with low consumption modulating circulator (EEI0.20) modifiable up to 7m head Hydraulic connections cover (optional) Possibility of intubating flues with the special flue ø 60 in PP and ø 50 in PP (only ErP boilers) Template, plumbing fittings, gas and sanitary taps supplied For gas conversion, contact authorized Beretta Technical Assistance Centres   Beretta is “ERP”. The concrete commitment towards an eco-sustainable future   The acronym ErP, acronym of "Energy related Products" (Products connected to the use of energy), identifies the Directive 2009/125/EC aimed at reducing the energy consumption of products through eco-compatible design. Starting from 26 September 2015 , the date of its effective entry into force in the European Union, it will mark an epochal turning point for heating products and the production of domestic hot water. On that date, other regulations issued at the same time for the energy labeling of products to supplement the corresponding Directive 2010/30/EU will also become effective.  The regulation provides that all products intended for heating and for the production of domestic hot water with a nominal thermal power lower than or equal to 70 kW can only be placed on the market with an energy label that highlights the efficiency class * . Different energy efficiency labels have been provided based on the different types of appliances/technologies, but all have the same graduated color scale that identifies the various levels of efficiency at a glance. The purpose of the labels is to give the consumer the possibility to easily identify the level of efficiency of a product and to be able to make a homogeneous comparison between products that use different technologies. For products whose transformation efficiency is influenced by external conditions, such as heat pumps, the efficiency data is reported by climatic bands.   In addition to the product labels, the European regulation has provided for the creation of a system label in case systems are created with different appliances, components and related controls. This second type of labeling, thanks to the virtuous synergy between the different elements, will make it possible to create systems capable of reaching levels of efficiency even higher than those of the individual devices. Also starting from the same date, new seasonal efficiency limits will be triggered for products intended for heating and combined. These for products with nominal thermal power equal to or less than 400kW, will prevent less efficient products from being placed on the market. The obligation to comply with minimum heat loss limits will also apply to DHW tanks. For primary water tanks, these will be subject to compliance with an energy classification based on heat dispersion. For sanitary accumulations, up to 500 liters there will be a labeling obligation, from 500 to 2000 liters will be bound to compliance with the energy classification. For heat pumps for heating and mixed appliances, in addition to the seasonal efficiency limits, there will be specific noise emission limits for power sizes. Even water heaters, whether gas, heat pump or solar, in order to be placed on the market, in addition to energy labelling, will have to comply with a series of requirements in terms of efficiency.   Warranty All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.

Read more less