SIME BRAVA ONE 30 HE METHANE condensing BOILER COMPLETE WITH FUME EXHAUST KIT For heating and domestic hot water production DHW thermal power kW 4.8÷28.0 Heating thermal power (50-30°C) kW 4.8÷28.0 Efficiency class (EEC 92/42): **** Continuous DHW flow rate Δt 30°c: 12.9 l/min Heating energy efficiency class: A Dimensions (h x w x d): 700 x 400 x 250 mm; 28.4kg METHANE version GOOD ONE Premixed condensing boiler Wide modulation range Stainless steel coil exchanger Extremely compact dimensions Three-piece cloak DHW management with dedicated probe Retroactive combustion control with electronic gas valve Can be installed outdoors and recessed using accessories (see page 78) 2 versions with 24.0 and 28.0 kW domestic hot water production Integrated climatic regulation Incredible dimensions for its potential The particularly compact dimensions are the most evident feature of the new Brava Slim and Brava One: 70 cm x 40 cm x 25 cm for almost all models, up to 35 kW of power. A unique result on the market! For example, comparing the condensing versions with previous models, there is an average decrease in volume of over 30% You will sleep soundly With Brava Slim and Brava One, Sime adopts the brass hydraulic group on all the boilers in the range. Brass, synonymous with quality, reliability and long life, guarantees peaceful sleep. The new hydraulic group also introduces the order of connections according to the DIN standard, adopted by the majority of European manufacturers, a further guarantee of maximum installation flexibility of Brava Slim and Brava one. For every action the perfect reaction Boiler manufacturers have always been concerned with developing the most efficient and ecological combustion. The passage of time often nullifies these efforts, lowering the quality of the combustion due to uncontrollable physical drifts. An active control of the combustion allows maintain the system within predefined efficiency, safety and emissions limits. The system is based on two fundamental components: the ignition electrode and the control electronics. The electrode, immersed in the flame, acts as a combustion control sensor providing feedback to the electronics that regulates combustion continuously. Advantages: Simple commissioning, high reliability and low maintenance over time Maximum safety in the event of poor exhaust gas evacuation or recirculation of unburnt gases (not detectable by traditional systems) Better control of combustion drifts caused by machining tolerances, oxidation and insulation losses No mechanical settings: electronic calibration of the gas valve Increased reliability by eliminating the air pressure switch in traditional combustion boilers Easier natural gas/LPG changeover via a simple parameter in condensing boilers and safe operation in the event of using the wrong gas Versatile and adaptable to any environment The extremely compact dimensions of Brava Slim and Brava One offer maximum assembly flexibility: all condensing and sealed chamber models from 25 to 35 kW are suitable for outdoor or recessed installation using simple accessories. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€656,00
Technical features ErP energy efficiency class (heating and DHW): A Load profile: XXL DHW nominal heat input kW 34 Heating nominal heat input kW 28.9 Sanitary nominal thermal power kW 33 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.7% Efficiency at 100% Pn (50-30°C): 105.5% Expansion/pre-charge vessel capacity l/bar 8/0.8 Sanitary water temperature adjustment °C 35-60 Sanitary water production ∆T 25°C l/min 18.9 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions ( HxWxD ): 763 x 450 x 345 mm Weight : 43.5Kg Power supply: METHANE Wall-hung gas condensing boilers ideal for replacing old systems with cast iron/lamellar steel radiators The new condensing range Luna Alux is divided into two models, 24 and 33 kW for heating and instant domestic hot water production. Luna Alux was designed in compliance with the requirements of the Ecodesign and Labeling Directives. The labeling directive (2010/30/EU) requires the labeling of products according to a decreasing energy scale that goes from A++ to G starting from 09/26/2015 and from A+++ to D from 09/26/2019. The label was created to allow the final consumer, by providing true and comparable data, to make informed choices by targeting high-efficiency products. Exclusive design aluminum heat exchanger Luna Alux is the new Baxi condensing boiler equipped with a corrosion-resistant aluminum-silicon alloy exchanger which makes this boiler particularly solid. The exchanger, designed and produced on an exclusive Baxi design, has been studied with large water passage sections to make the boiler particularly suitable for replacement in old heating systems with cast iron or lamellar steel radiators In these types of systems, the replacement of the existing boiler with a new LUNA ALUX: Significantly lowers the risk of clogging due to impurities in the system water Makes operation particularly quiet The high water content inside the exchanger determines: Less temperature fluctuations Increased overheat protection More effective DHW pre-heating Furthermore, the exchanger can be inspected and this facilitates periodic maintenance Digital control panel The Luna Alux range of boilers is equipped with a digital control panel with backlit LCD display, easy to use thanks to dedicated and independent keys to adjust the temperature of the domestic hot water and the heating. The display allows you to view all the information and set the operating parameters in a clear and immediate way. Efficiency and savings Wide modulation range: Greater efficiency given by less switching on and off: with a high modulation ratio, the reduction of continuous switching on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions adjustment of the thermal power produced to the power dissipated thus avoiding excessive overheating/cooling of the premises Hydraulic group in brass Baxi has chosen to maintain quality in its components. The brass hydraulic group, in fact, is a guarantee of: Robustness Greater durability Recyclability Wide modulation range 1:7 greater efficiency given by fewer starts and stops: with a high modulation ratio, the reduction of continuous on/off cycles leads to a significant reduction in consumption (by 8-10%) and an equal reduction in polluting emissions • power adjustment produced at the dissipated power thus avoiding excessive overheating/cooling of rooms A Gas Adaptive Control The innovative GAC (Gas Adaptive Control) automatic combustion control system guarantees a wide modulation range up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adjust the thermal power produced to the actual power dissipated from the building avoiding excessive heating/cooling of the building. High efficiency total modulation pump The Alux range is equipped with a high-efficiency, fully modulated circulation pump. The pump is equipped with a permanent magnet motor with a variable rotation speed controlled by the boiler board. The high efficiency total modulation pump allows: Lower electricity consumption Better performance Greater durability Characteristics: Wide modulation range 1:7 greater efficiency and silence GAC (gas adaptive control): automatic combustion control to constantly maintain the maximum efficiency values (operation on methane only) High efficiency circulation pump with total modulation Aluminum-silicon alloy exchanger with large water passage sections Hydraulic group in brass 10 liter expansion vessel (mod. 33) Easy maintenance thanks to front access to components Digital control panel with large backlit LCD display Arrangement for combination with the Baxi integrated solar system Electronic system deaeration function to facilitate air removal during initial ignition Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€1.410,00
Hermann Saunier Duval THEMA CONDENS 30 kW condensing boiler complete with low NOx flue gas kit - Methane Model: Efficiency class Heating efficiency class A Sanitary efficiency class - A Sanitary load profile - XL Heating Rated power Pmin/max - 80/60°C kW 6.6 / 26.7 Efficiency Pmax % 109.2 Sanitary Rated power min/max - 60°C 6.1 / 30.6 kW Specific flow rate (DT = 30K) (EN13203) l/min 18 generals Supply gas - methane Max absorbed electric power (W) Nox class - 5 Electrical protection IPX - 5D Dimensions mm (HxLxP) 740x418x344 THEMA Condens Wall-mounted condensing boiler with pre-heating and Aquaspeed® technology. The Thema Condens range features combined methane and propane models, all equipped with a primary heat exchanger in anti-corrosion stainless steel and an 8-litre expansion tank (heating side), perfect for single-family homes. The Thema Condens range is enriched with two models: IS and AP dedicated to multi-family solutions for both single and multiple ducting. Thema Condens IS is available in two versions of 26 and 30 kW with natural gas supply and convertible to propane . The AP version, on the other hand, is only available in the 26kW methane power size. The IS version features a dedicated flue kit consisting of a flue non-return valve, 80/125 mm adapter with 87° bend and rigid section for connection directly to a single flue. In the HP version Thema Condens has a safety pressure switch and a fan with increased head which allows reaching vertical ducts up to 30 meters with self-adaptation of the required length via the system electronics. Vertical ducting with DN 50, both rigid and flexible, is also possible, which solves the problems in old flues and in those where the available space is minimal. Primary heat exchanger in anti-corrosion stainless steel Sanitary comfort ★★★ thanks to the exclusive Aquaspeed® technology Continuous domestic hot water (DHW) production up to 18 l/min Pre-heating function and DHW plate exchanger in stainless steel Solar Easy: predisposition for solar integration Warranty extension up to 5 years Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.230,00
Riello Residence Condens 30 kis condensing boiler complete with LPG Low NOx flue gas kit class A - NEW Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Heating/DHW operating characteristics Heating nominal heat input kW 20 Nominal thermal power (80°-60°) heat kW 19.5 Maximum heating pressure bar 3 DHW nominal heat input kW 25 Nominal thermal power* sanitary kW 26.3 Hot water production with t+25 °cl/min 15.1 NOx class 5 Dimensions HxWxD mm 740x420x350 Electrical data Total electric power (pmax heating) W 75 Supply voltage V - Hz 230 - 50 IP X5D degree of protection Power supply: LPG (It self-adapts without using external kits) RESIDENCE CONDENS RIELLO PRESENTS RESIDENCE THE NEW RANGE OF CONDENSING BOILERS NEW EXCHANGER Wrapped stainless steel primary exchanger. Efficiency and reliability in the heart of the Residence. DOMESTIC COMFORT FUNCTION Domestic water pre-heating with Touch&Go function for activation upon request directly from the drawing tap. ACTIVE COMBUSTION CONTROL Advanced electronic combustion control system which constantly monitors combustion to obtain constantly optimized consumption and emissions. DIGITAL USER INTERFACE Simple and intuitive backlit LCD display. Ease of setting thanks to the silk-screened keys dedicated to the individual user functions. MODULATING CIRCULATOR High efficiency circulator with flow rate modulation and regulation logic that can be set between different modes according to the type of system. HIGH EFFICIENCY The high efficiency of the primary exchanger, the modulating circulator and the continuous control of the combustion parameters guarantee very low consumption even after years of operation. QUICK INSTALLATION Speed and ease of installation thanks to the compact dimensions, accessibility of the components and external electrical connections. UNIQUE VERSION METHANE - LPG Dedicated codes are no longer necessary in the case of LPG because Residence is able to automatically adapt its operation to the type of fuel with rapid setting from the display. FLEXIBLE INSTALLATION The characteristics of Residence and its compact dimensions make it the ideal solution for both indoor and recessed installation (model 25 KIS only) or outdoors in a partially protected place. RESIDENCE, HEART OF STEEL The new RESIDENCE exchanger is made of stainless steel, with a smooth tube with a large section to guarantee the best efficiency and cleanliness over time. NEW PRIMARY EXCHANGER IN STAINLESS STEEL The single coil geometry (hydraulic circuit in series) guarantees constant flow in all sections of the exchanger and intrinsically prevents clogging. Front access facilitates periodic maintenance and cleaning of the combustion chamber. SELF-ADAPTING ELECTRONIC COMBUSTION CONTROL The new Residence is equipped with the intelligent ACC combustion control system, which guarantees that the process always takes place in an optimal manner in any condition, thanks to the modulating gas valve and the ionization electrode. Thanks to the ACC, Residence is able to automatically adapt to the fuel (methane or LPG) without resorting to specific codes or accessory conversion kits. Residence also reacts to the variation of the fuel title and to the pressure drops on the flue gas side. The ACC system detects the excess air value and intervenes by modulating the mixture. The ACC system also simplifies installation. During ignition, it does not require calibration and it is sufficient to select the type of combustible gas used by the boiler via the interface, if different from the default one (methane). Since the system keeps the value of the CO2 produced constant, even the smoke control during the ignition phase is no longer necessary for the correct functioning of the product. Controlling combustion also means guaranteeing constant emissions, which are always well below the limits set by the law. In fact, if the process takes place in an optimal manner, the gases produced will also have the best theoretical composition with respect to the other conditions. MANY NEEDS, ONE SOLUTION RESIDENCE IS ALWAYS THE IDEAL CHOICE THANKS TO THE TECHNICAL SOLUTIONS AND THE COMPACT DIMENSIONS, IT CAN BE USED IN ANY INSTALLATION SITUATION INTERIOR Inside the home, thanks to an elegant aesthetic that allows it to be inserted pleasantly into any environment. OUTDOOR Outdoors in a partially protected place, thanks to the IPX5D degree of protection and the accessory antifreeze heater kit RECESSED Inside a built-in box thanks to its compact dimensions (model 25 KIS only). NEW DIGITAL CONTROL Setting your own comfort for domestic hot water, air and heating is immediate thanks to the buttons with symbols dedicated to the individual functions Domestic hot water temperature setting Operating status 0FF - SUMMER - WINTER Unlock and restore alarms Information and parameters menu Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.065,00
SAVIO actaDENS 30 S condensing boiler complete with low NOx methane fume exhaust kit - News Code 10304.2029.0 Acta Dens model Performance DHW nominal heat input kW (kcal/h) 31.0 (26655) Nominal heat input * heating kW (kcal/h) ) 26.0 (22356) Maximum useful power in heating 60/80° kW (kcal/h) 25.4 (21840) Useful power in DHW 60/80° kW (kcal/h) 30.3 (26053) Efficiency at 100% load (50/30 °C) % 107.3 Sanitary flow rate ∆t =25°K l/min 17.6 8 liter expansion tank NOx class 6 Dimensions Dimensions HxWxD mm 703x400x325 actaDENS Acta Dens completes the Savio range with premixed condensing: perfect for radiator systems and suitable for radiant systems with mixing groups. ActaDens is the compact condensing boiler that ensures high yields, low consumption and respect for the environment. Available for heating and domestic hot water production, in power ratings of 25 and 30 kW. Main features Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion Total premix burner, stainless steel (Nox class 6) Modulation 1:5 CNG and also LPG Sanitary plate heat exchanger in stainless steel 8 liter expansion vessel High efficiency pump with low energy consumption Can be installed in a partially protected place Integration with SAVIO solar systems, using a solar kit Analog pressure reading Arrangement for remote control and external probe High circulation single coil primary heat exchanger Savio introduces the new stainless steel heat exchanger for condensing boilers to the market: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. Using a single stainless steel strip to produce the coil, including inlet / outlet connections, the following advantages are obtained: The accumulation of dirt and debris is avoided The water flow is uniformly distributed and guarantees a homogeneous heat exchange Reduction of pressure drops with optimized circuit. The ease of cleaning and the robustness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. Control panel: Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history The display operates in the following modes: INFO – information available on the operating status and error history FREE programming – programmable parameters for generator/system adjustment and User SET INSTALLER programming - generator parameters ASSISTANCE programming - Authorized Assistance Center parameters Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€883,00
ATTENTION THE BOILER IS BORN WITH METHANE. THEREFORE, THE STANDARD TRANSFORMATION KIT WILL BE SUPPLIED. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Technical features Product code: 3301022 Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal thermal power kW 28 Annual energy consumption in heating 50 gj Annual electricity consumption 42 kWh Seasonal space heating energy efficiency % 94 Water heating energy efficiency % 82 Sound power level inside 51 dB DHW flow rate ∆T 25 °C (l/min) 17.4 Dimensions 24 kW mm (HxWxD) 745 x 400 x 315 Indoor installation and partially protected places Power supply: LPG Functionality: Wi-Fi optional XtraTech™ stainless steel primary exchanger AUTO, Comfort functions Indoor installation and partially protected places XtraTech™ is the new exclusive* Ariston stainless steel heat exchanger, the heart of the ONE condensing boilers, developed to guarantee reliability and performance over time. Increased passage sections: +142% compared to the previous exchanger. Higher prevalence, lower risk of clogging, better performance. Every day, as if it were the first. Every single component has been designed to guarantee performance and durability over time: Ariston guarantee, shown in each component. Every single component has been rigorously tested and controlled on the production line. 100% of the boilers are tested again before being shipped to our customers. The best materials have been selected, to work for a long time even in the most critical situations Always connected with Ariston NET Wherever you are, always within reach of your Smartphone. Managing the comfort of your home has never been easier! Wherever you are, you can control the climate in your home using your smartphone. Use only the energy it needs. Easy to manage weekly time programming, directly from the app. Also, choose the savings "leaflet" for a real reduction in bill costs! Technical support always ON. Thanks to the innovative remote control system, the app warns your customer in case of malfunctions. By signing a maintenance contract, the Assistance Center will be able to intervene in the event of breakdowns, even remotely. Customer serenity is at the heart of Ariston NET. Absolute efficiency: Thermoregulation in class A+ The ONE condensing boilers achieve very high seasonal performance and thanks to the thermoregulation they reach class A+! Alteas and Genus ONE are also equipped with the innovative IGNITION system, which makes combustion always perfect thanks to the electronic control. Gas transformation? No problem, from the technical menu in one touch. Total Comfort: Innovative functions to meet your needs ONE is equipped with an innovative set of smart functions to guarantee comfort every day with minimum waste of energy. Auto function: Patented function that allows you to automatically optimize the operation of the boiler, eliminating continuous switching on and off, reducing the stress on the components to a minimum. Comfort function: Hot water without any waiting! Lots of water with minimum energy consumption. Integrated Programming: Weekly hourly programming integrated into Alteas and Genus ONE products. Care function: Automatic reminder of routine maintenance. Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.015,00 - €1.123,00
Overview BAXI DUO-TEC MAX+ 33 GA CONDENSING BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ErP 2015 Technical specifications ErP energy efficiency class (heating and DHW): A Load profile: XL Sanitary nominal heat inputkW 34ÿ Heating nominal heat input kW 28.9 Sanitary nominal thermal powerkW 33 Energy efficiency(92/42/CEE)ÿ**** Efficiency 100% Pn (80-60øC): 97.8% Efficiency 100% Pn (50-30øC): 105.8% Expansion/pre-charge capacity l/bar 8/0.8 Sanitary water temperature adjustmentøC 35-60ÿ Sanitary water production T 25øC l/min 18.9 Degrees of protection: IPX5Dÿ NOx class (EN 483) 5 Dimensions (hxwxd): 760 x 450 x 345ÿmmÿ; 39.5 kgs Power supply: LPG Features list Duo-Tec Max+ The new range of gas condensing boilersÿDuo-tec+ÿ has been specifically designed in compliance with the requirements of the Ecodesign and Labeling Directives, to make it particularly suitable both for new buildings and for replacing an old generator. In fact, in addition to the already known advantages of condensing technology such as efficiency, energy saving and reduced polluting emissions, the new Duo-tec+ condensing boilers are characterized by: Complete range of models: heating only, with instantaneous DHW production, with integrated micro-storage tank, with integrated 40 liter storage tank. The range also includes the compact version (Compact+), the first Baxi condensing boiler in just 70 cm in height and 30 cm in depth. Digital control panel with backlit LCD display Wide range of 1:7 modulationÿreduction of on/off cycles translates into significant benefits in terms of energy savings and lower emissions digital control panel The Duo-tec+ range of boilers is equipped with a digital control panel with backlit LCD display, simple to use thanks to dedicated and independent keys for regulating the temperature of the domestic hot water and of the heating. The display allows you to view all the information and set the operating parameters in immediate change. Gas Adaptive Control The innovative automatic combustion control system GAC (Gas Adaptive Control) guarantees a wide modulation range of up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adapt the thermal power produced to the effective power dissipated by the building, thus avoiding excessive overheating/cooling of the building. Full modulation pumpÿ Can the circulation pump operate at maximum speed, at minimum speed in mode or automatic?: in the latter case, the speed (min./max) will be selected so that the heating delivery/return T remains constant at 20°C thus guaranteeing a significant reduction of pump consumption and, given the lower mechanical stresses (compared to a pump that always runs at maximum speed), also of maintenance costs Characteristics: *** of sanitary comfort(EN 13203) wide modulation ranges fine 1:7 greater efficiency and silence GAC (gas adaptive control): automatic control of combustion mini accumulator integrated in the expansion vessel (Baxi patent) digital control panel with large backlit LCD display high-efficiency circulation pump with total modulation antifreeze function IPX5D protection degree To be placed on the EU market, a productÿmustÿhave the brand,ÿthat is, comply with all the European Directives applicable to it.ÿ The ÿEcodesign and Labellingÿ Directives (eco-design and energy labelling) were created to help the EU achieve the objectives of the EU Plan 20-20-20, with a particular focus on reducing CO2 emissions by 20%, increasing energy efficiency 20% and the increase in the use of renewable energy by 20%, by 2020. For this reason, all heat generators for space heating, appliances for the production of DHW and systems of several of these appliances combined in combination will have to comply with the requirements for eco-design and be labelled, according to the quantity established by the implementing regulations, in order to be placed on the marketby producers. From 26 September 2015, the directives will affect all the products described above with a Pn 400 kW for eco-design and with a Pn 70 kW for labeling, destined for the markets of all countries of the European Economic Area. How is placing on the market Placing on the market is carried out by the manufacturer (by the importer from outside the EU) when the product remains available for the first time on the EU market.ÿThis happens when ownership changes to a distributor (invoice). ÿHow the placing on the market takes place Placing on the market is carried out by the manufacturer (by the importer from outside the EU) when the product remains available for the first time on the EU market.ÿThis happens when ownership changes to a distributor (invoice). ÿWhat products can be sold All products with CE marks placed on the market before 01/08 and 26/09 2015 are considered compliant and therefore salable until exhaustion. All products that will be placed on the market (sold) by the manufacturer/importer after these dates must comply with the new standards . What is a product according to ErP (Ecodesign) A device designed to operate at maximum efficiency with minimum environmental impact. To comply with this directive, the product must have Pnÿ 400 kW and as regards the hot water tanks, a volumeÿ 2000 litres. Manufacturers are obliged toÿplace on the marketÿonly ErP-compliant products with these deadlines: sinceÿAugust 1, 2015ÿonly products equipped with high efficiency pump fromÿ26 September 2015ÿonly products that meet the minimum ErP efficiency requirementsÿ Ecodesign defines the requirements that products must meet in order to be placed on the market, based on: Seasonal efficiencyÿfor heating and efficiency for DHW production based on the declared load profileÿ Emissionsÿ(NOx values)ÿ Maximum allowable noiseÿof hydronic heat pump outdoor unitsÿ What is a Combi product according to ErP An appliance (single with boiler) for heating and DHW production, already equipped with labeling with energy class information relating to a DHW loader profile. What is the energy label The labeling directive (2010/30/EU) requires the labeling of products according to a decreasing energy scale that goes from A + + + to GE An energy label is also provided for the installed system, depending on the components used (for example a boiler, DHW tank and room temperature controls). The label was created for the final consumer, providing real and comparable data, to make informed choices and targeting high-efficiency products. Warranty All products for sale on our site are new and packed. The guarantee on this article is 24 months from the date of purchase.
€1.346,00
IMMERGAS VICTRIX ZEUS SUPERIOR 32 KW METHANE CONDENSING BOILER WITH BOILER COMPLETE WITH FUME EXHAUST KIT - NEW ERP Technical features Model: Wall mounted condensing boiler with 45 liter Boiler; Energy class in heating: A; Sanitary energy class: A; Sanitary load profile: XL; Heating power: 32.0 kW; DHW power: 25.8 kW; Hot water production (∆t 30 °C) l/min: 19.2; Nominal Current: 0.64A; Electrical insulation degree IP X5D; Heating performance: Nominal system expansion vessel capacity (min./max.): 10.0/7.1 L; Head available with flow rate 1000 l/h kPa (m wc) 29.0 (2.95); Healthcare services: Useful thermal power for hot water production (kcal/h) 32.0 (27520) kW; DHW temperature °C 20 - 60: Sanitary pressure 2.5 bar: Withdrawal in continuous service (∆t 30°C) litres/min 15.8; Specific flow rate x 10 min. (∆t 30°C) litres/min 19.2; Boiler losses kW 0.168; Nominal expansion vessel capacity liters 2.5 (1.2) Power supply: LPG. Benefits and functions: Display: backlit liquid crystal, provides the main operating information; It is possible to take advantage of the tax deductions in force; Low consumption, and can be combined as an optional with thermoregulators, which improve comfort and increase energy savings; 45 l kettle; Eco-compatible technology: in compliance with the ErP and ELD European Directives, it allows to achieve high energy efficiency classes in heating and hot water production; Ecological class 5: reduced emissions of nitrogen oxides. General characteristics Immergas boiler, easy to install in any environment and compatible with existing fittings and whirlpool tubs, designed to respect the environment while enjoying maximum comfort with low energy consumption given its low consumption circulator. Equipped with a 54 liter boiler made of stainless steel to be unalterable over time with minimal heat loss so as to resist even outdoors. The wide flange optimizes cleaning and maintenance operations, which allows excellent thermoregulation, guaranteeing very high performance in terms of comfort. Inside the boiler, in turn, there is a stainless steel coil wound in a double concentric spiral which ensures rapid heat exchange. The Zeus boiler is intuitive and simple to use and to program to your liking thanks also to the practical knobs and a backlit display that allow you to manage and view the boiler settings. Finally, given its great reliability not only in performance but also in resistance (IPX4D protection degree) it can be installed both indoors and partially covered outdoors. Dimensions (HxWxD): 900x600x460cm; Warranty The guarantee on this article is 24 months from the date of purchase.
€2.752,00
Overview VAILLANT ecoTEC PLUS CONDENSING BOILER VMW 306/5-5 + vSMART WiFi COMPLETE WITH FUME KIT - NEW ErP 2015 METHANE Cod. 0020222965 Technical specifications For heating and domestic hot waterÿ Forced draft sealed chamber Nominal heat input in sanitarywarekW 30 ErP energy class (Heating and DHW): class A Stars of yield (according to Dir. 92/42CEE) - **** Domestic hot water production (T = 30K) 14.3 lt Domestic hot water comfort stars (prEN 13203) - *** Expansion tank capacity 10 l Massimcontenutd?Ó?water in plantl 180 Dimensions (hxpxl) mm 720 x 338 x 440 Total electric power/pump (max speed) W 80/35 NOx class - 5 Adjustable in wi-fi from smartphone ThermostatvSMART as standard Version:ÿMETHANEÿ Features list Vaillant condensing boilerÿ With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. Tuttquestentril 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for energy-using equipment, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes in the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation even at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. ecoTEC PLUS ecoTEC plus the excellence of wall-mounted condensing boilers minimum consumption, maximum efficiency and versatility TheÿecoTEC plus series, wall-mounted condensing boiler of the latest generation, conceived to guarantee maximum energy savings and maximum comfort and designed to satisfyÿthe requirements of European regulationsÿconcerning energy efficiency which will enter into force inÿSeptember 2015. In addition, all the new products and systems for heating and water production hot water heaters must be labeled with an indication of their energy efficiency class. TheÿecoTEC plusÿlabeling signals theÿclass A. ecoTEC plusÿreaches this result easily because, in addition to the typical elements of Vaillant boilers, it has new completely innovative components: the combustion management system (ELGA), which, skilfully mixing air and gas, results in a reduction in gas consumption, new electronics and the very high efficiency to ensure considerable savings in electricity. For example, the electricity consumption of the boiler in stand-by is less than 2Watt (less than half of a working radio). ecoTEC plusÿguarantees maximum comfort: the boiler supplies immediately available hot water without sudden changes in temperature. Thanks to its small dimensions (70 cm high, 44 cm wide and 35 cm deep)ÿecoTEC plusÿ can be easily installed on any wall. Today it is possible to install it outdoors where the climate is mild even in winter. ecoTEC plusÿhas, in fact, also an anti-gel device which allows it to resist up to temperatures that reach -5°C. The newÿsimple and intuitive design, thanks to the display with clear text and backlighting, makes the boiler functional, allowing the user easy setting and simple control. ecoTEC plus compatible with all Vaillant components and accessories already on the market. Features:ÿ Boiler ready for 2015 regulations ErP: class A Preheat DHWÿ *** DHW comfortÿ Antigel-5øC as standard **** Efficiency in heating Modulation 1:8ÿ Modulating pump (Class A) Primary heat exchanger Vasexpansion 10 lÿ ELGA combustion system transfer kit from methane propan supplied WiFi programming from smartphone tablet wherever you are with vSMART and App vSMART VaillantÿvSMARTÿ the advanced WiFi thermoregulation system that allows you to configure the comfort of your home at any time with a simple click on your smartphone tablet. The benefits of vSMART are not limited to convenience. Using andvSMART you drastically reduce the start/stop cycles of the boiler thus allowing you to save on gas and electricity and to extend the life of your appliance. vSMARTÿtransforms your smartphone tablet into a remote control system for your heating. Wherever you are and whatever you are doing, you will be able to control and adjust the comfort of your home in extremely intuitive mod-rapid using your WiFi network. Download the free ÿvSMARTÿapp from the tuStore. To download the App, simply enter the tuStore, search for vSMART and start the download. The Vaillant vSMART App is available for iOS and Android systems. vSMARTÿ Designed to ensure comfort and extreme ease of use. You can install it on the wall by connecting it to the electricity supply and place it where you prefer using common AA + batteries. Elegant and essential, it integrates perfectly into any environment. One device to save energy for others. With vSMART you can - Control heating and domestic hot water via App.ÿ - Have 30 pre-configured and customizable standard profiles available.ÿ - Monitor energy efficiency at all times.ÿ - Control the heating systems of several homes (e.g. two flats, two houses).ÿ - Check the historical data of temperature, mode and hours of operation.ÿ - Regulate the temperature based on climate data collected from the internet.ÿ - Quickly set the function or Away from Home? or Antifreeze? for greater savings.ÿ - Take advantage of the self-learning function that recognizes your programming over time to make your life even easier. The new EU legislation Starting from 26 September 2015 it is no longer possible to produce traditional forced draft boilers. Instead, it will be possible to continue producing condensing boilers and traditional open chamber boilers equipped with high efficiency pumps and compliant with the new ErP requirements such as emission levels, noise levels and efficiency. In particular, the installation of traditional open chamber boilers will only be possible in replacement of old boilers installed in multi-family buildings which discharge fumes into branched collective flues (CCR). Products placed on the market before 26/09/2015 that do not comply with the requirements of the new directive, such as traditional forced draft boilers and boilers not equipped with a high efficiency pump, can still be purchased, sold and installed. ErP and ELD: what they mean and how they differ ErP: The EU has issued new obligations for Energy Using Products (ErP). The new directive, known as the Ecodesign directive, prescribes minimum efficiency requirements and emission limits for appliances that produce heating and domestic hot water. The Ecodesign directive addresses two relevant product categories for installers and retailers in the sector: -ÿCategory 1ÿIncludes space heating appliances: electric, gas, oil, combined boilers, heat pumps and cogenerators up to 400 kW. -ÿCategory 2ÿIncludes appliances for the production of domestic hot water: electric, gas, diesel, heat pumps for DHW, solar systems up to 400 kW and boilers up to 2000 litres. ELD:ÿIn addition to the ErP directive, the EU has also introduced mandatory energy labeling for the same types of appliances up to 70 kW and boilers up to 500 litres. The energy labeling directive is called ELD and requires that new products and systems for heating and domestic hot water production are labeled with an indication of their energy efficiency class. By combining products and components, for example by adding a temperature control unit, the energy classification of the system can be increased, which will be calculated by the installer and indicated on the package label. 7 year guarantee The 7-year guarantee on new boilers is another excellent reason to offer Vaillant to your customers. In addition, know that by replacing a Vaillant boiler over 15 years old with a new generation one, the warranty extension will be provided free of charge by the Official Vaillant Technical Assistance Center against a maintenance contract. Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.710,00
Riello FAMILY CX 30 KIS condensing boiler complete with Low NOx methane fume exhaust kit - NEW ErP technical data Energy class A XL load profile NOx class 6 Warm-up exercise characteristics Nominal heat input kW 25 Nominal thermal power (80°/60°) kW 24.33 Maximum pressure bar 3 Features exercise in sanitary Nominal heat input kW 30.00 Nominal thermal power (*) kW 31.50 Maximum pressure bar 8 Electrical data Supply voltage V-Hz 230-50 IP X5D degree of protection Dimensions WxDxH mm 470x350x740 New Family The new Family is the Riello solution for the most demanding user. The primary exchanger, entirely made of stainless steel, guarantees maximum efficiency and reliability over time and the new optimized sanitary exchanger ensures exceptional comfort and the best class of merit (class A). The new Family is available with powers of 25, 30 and 35 kW, in instantaneous combined and heating only versions. – ACC self-adaptive electronic combustion control – Range Rated Approval – Possibility of integration in hybrid systems – New panel with color display and intelligent system filling function – 10 liter expansion tank – Low consumption modulating circulator – Modulation ratio 1:8 – Standard flue gas flange with dedicated flue system – Clapet valve and SRD device as standard – Standard thermoregulation in combination with the external probe, available as an accessory – Possibility of recessed installation (model 25 KIS) and outdoors in partially protected places (IPX5D) – Ease of installation and wide choice of accessories - Primary heat exchanger in stainless steel - High performance sanitary exchanger - Self-adaptive electronic combustion control - Class 6 NOx Combined and heating only models, MTN and LPG compatible Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.403,00
Technical features ErP energy efficiency class (heating and DHW): A Load profile: XXL DHW nominal heat input kW 34 Heating nominal heat input kW 28.9 Sanitary nominal thermal power kW 33 Energy efficiency (92/42/EEC) **** Efficiency at 100% Pn (80-60°C): 97.6% Efficiency at 100% Pn (50-30°C): 105.4% Expansion/pre-charge vessel capacity l/bar 8/0.8 Sanitary water temperature adjustment °C 35-60 Sanitary water production ∆T 25°C l/min 18.9 Degree of protection: IPX5D NOx class (EN 483) 5 Dimensions (h x w x d): 760 x 450 x 345 mm ; 39.5 kgs Power supply: CNG or LPG *Operation on LPG through adjustment by the Authorized Assistance Centre Moon Platinum+ Wall mounted condensing gas boilers for heating only and instant DHW production. Ecodesign and Labeling - From Baxi research comes a complete range of condensing boilers with high technological content designed in compliance with the requirements of the Ecodesign and Labeling directives, to ensure maximum domestic comfort. Latest generation electronics, high efficiency and compact design make the Platinum+ range the ideal solution for both new installations and replacement. THINK raises system efficiency - The Platinum+ range of boilers is designed with the Think technology platform - intelligence within, an exclusive system that makes them "think" intelligently! With this authentic "the brain inside the box", the Baxi proposal confirms itself as the intelligent choice for making the boiler communicate in a simple and flexible way with all the main heating technologies, creating increasingly complex and energy-efficient design solutions. Furthermore, the Think platform makes the boiler very easy to use, in line with the Baxi design tradition aimed at totally user-friendly management of the appliance. Even the least experienced user can thus interact with the new control panel and program his own domestic comfort with the utmost simplicity. With the range of condensing boilers with the Think platform, Baxi comfort is easy and smart. The combination of the Platinum+ boiler for heating and DHW production and THINK controls for intelligent management of the system allows efficiency to be raised to class A+. The Platinum+ range is equipped AS STANDARD with a removable control panel for remote management (wired or wireless) of the boiler, equipped with a large multifunction text display with modulating thermoregulation control unit functions. GAC - The innovative automatic combustion control system GAC (Gas Adaptive Control) guarantees a wide modulation range up to 1:10: high efficiency and energy savings are ensured as the boiler is able to adapt the thermal power produced to the effective power dissipated by the building avoiding excessive overheating/cooling of the building. Efficiency and savings - The objective of a heat generator is to supply the energy necessary to the rooms to maintain maximum comfort conditions inside: this means supplying the rooms, through the system, with the same amount of heat the building disperses. In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. Total modulation pump The Luna Platinum+ range is renewed with the introduction of a high efficiency electronic pump with permanent magnet motor. The new fully modulated pump allows, compared to using a pump traditional modulating: Lower electricity consumption Better performance Greater durability Plant deaeration New electronic "system deaeration" function to facilitate the removal of air during initial ignition. Efficiency and savings The objective of a heat generator is to supply the energy necessary to the rooms to maintain conditions of maximum comfort inside them: this means supplying the rooms, through the system, with the same amount of heat that the building loses . In new buildings, the regulations increasingly require greater insulation and consequently less dispersion. Usually there is a tendency to oversize heat generators to favor the production of sanitary water: this leads to an excess of power in heating which, together with the poor modulation capacity of traditional boilers, causes discontinuous functioning and therefore waste of fuel. Discontinuous processes generate energy losses (heat dispersion caused by the pre-washing of the combustion chamber, component wear caused by continuous on-off, decrease in generator efficiency). The modulation system of the Platinum+ range is able to adapt the thermal power produced to the effective power dissipated by the building, avoiding excessive overheating/cooling of the rooms. The graph shown above highlights the reduction in on/off cycles which distinguishes the new Platinum+ boilers with modulation up to 1:10 compared to a condensing boiler with lower modulation. The reduction of the on/offs determines an improvement in the efficiency of the boiler and consequently a considerable saving for the end user. Standard condensing boilers, on the other hand, with a limited modulation range work at a minimum power level above 6 kW; this allows it to avoid the on/off cycles for only 3% of the period of operation in heating, compromising the performance of the boiler and the life of the components. GAC : Gas Adaptive Control The electronics and the gas valve with stepper motor that the new Platinum+ boilers are equipped with guarantee automatic combustion control which is based on: on the flame signal The system continuously measures the flame signal during boiler operation and adjusts the gas flow rate so as to maintain the quality of combustion constant and all this without requiring any additional component inside the combustion chamber. Installers and end users enjoy the following benefits of the GAC: The automatic combustion control favors a reduction in installation times as no manual adjustment of the gas valve or nozzle change is required: in fact, it is sufficient to manually modify some parameters of the electronic board for operation with LPG The boiler self-adapts to the quality of the gas and the length of the flue gas outlets: this means that there are no manual adjustments to make High modulation field 1:10: high efficiency and savings, since such a wide modulation field determines a greater adaptability of the boiler to the thermal dispersions of the building to obtain a higher efficiency and greater durability of the components. The reduction of the on/off cycles, in addition to the greater efficiency, guarantees less noise produced by the boiler Unlike traditional condensing boilers, the boiler always works adjusted to maximum efficiency values favoring a reduction in gas consumption and consequently a lower environmental impact thanks to the control of CO/CO2 emissions Power sets The term Power set identifies the heating power regulation process according to the project data. The thermal capacity of the boiler, through the Power set device, is adjusted according to the energy requirement: just act on the control panel to adjust some parameters. Complete soundproofing C structure Silence is the relative or absolute absence of sound or noise. The noise level of the Luna Platinum+ boiler is comparable to a normal conversation. Digital pressure gauge The electronic pressure transducer in the hydraulic unit allows you to check the pressure directly on the display. Double alarm level in the event of low pressure: a "warning" level in the event of low pressure in the boiler; a "block" level in the event of a lack of pressure. Intubation solution For the rehabilitation of flues Baxi has developed a system that allows easy ducting in existing flues thanks to a Ø50 mm exhaust pipe (for 24kW models) Characteristics: wide modulation range 1:10 greater efficiency and silence GAC (gas adaptive control): automatic combustion control high-efficiency circulation pump with total modulation removable and backlit control panel in wireless and wired version for wall installation, with large text display, adjustment knob and menu selection keys power set: heating power adjustment according to project data integrated electronic management for coupling to a solar system Ø50 mm exhaust pipe: solution for restoring flues - mod. 24 kW STANDARD installation kit (gas cock / DHW inlet / telescopic fittings) antifreeze function and IPX5D degree of protection Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€1.341,00
Biasi ac condensing boiler complete with LPG Low NOx ErP Fume Exhaust Kit - NEW Model BASIC COND 30S DHW nominal heat input kW (kcal/h) 31.0 (26655) Nominal heat input * heating kW (kcal/h) 26.0 (22356) Maximum useful power in heating 60/80° kW (kcal/h) 25.4 (1840) Useful power in domestic hot water 60/80° kW (kcal/h) ) 30.3 (26053) Efficiency at 100% load (50/30 °C) % 107.3 Sanitary flow rate ?t =25°K l/min 17.6 NOx class 6 LPG code 10304.2029.0 Dimensions HxWxD mm 703x400x325 BASIC COND Basica Cond Basica Cond completes the BIASI range with premixed condensing: perfect for radiator systems and suitable for radiant systems with mixing groups. Basica is the compact condensing boiler that ensures high efficiency, low consumption and respect for the environment. Available for heating and domestic hot water production, in power ratings of 25 and 30 kW. Main features Primary condensing exchanger in stainless steel with steel lining to offer maximum resistance to corrosion - Total premix burner, stainless steel (Class NOx 6) - Modulation 1:5 CNG and also LPG - Sanitary plate heat exchanger in stainless steel - 8 liter expansion vessel - High efficiency pump with low energy consumption - Can be installed in a partially protected place - Integration with BIASI solar systems, using a solar kit - Analog pressure reading - Arrangement for remote control and external probe High circulation single coil primary heat exchanger Biasi introduces on the market the new stainless steel heat exchanger for condensing boilers: Round. Round is a compact monothermal heat exchanger based on a stainless steel coil with an oval section. The heat exchanger consists of a combustion chamber, condensing area and an insulated metal disc protected with silicone ceramic fiber which separates the two areas. By using a single strip of stainless steel to produce the coil, including inlet/outlet fittings, the following benefits are achieved: - The accumulation of dirt and debris is avoided - The water flow rate is constant, guaranteeing a higher average life of the product - Reduction of load losses with optimized circuit. The ease of cleaning and the sturdiness of this exchanger are one of the main strengths of the product since it can be used on new systems but also on old systems in the event of renovations. Round integrates the round flow function in which the water produces a centrifugal cleaning effect on the internal walls of the single coil. The absence of circuits in parallel guarantees an easy "washing" operation of the exchanger and the elimination of any air present in the system circuit. Included in delivery Boiler support bracket and paper template Boiler power cable Condensate collection siphon Quick instruction to the user. Control panel Summer/winter/off selector Heating temperature regulator DHW temperature regulator Analog pressure reading DHW and heating temperature visualization from the display Display of fault diagnostics, block status and fault history The display operates in the following modes: INFO – information available on the operating status and error history FREE programming – programmable parameters for generator/system adjustment and User SET INSTALLER programming - generator parameters ASSISTANCE programming - Authorized Assistance Center parameters commands The Basica Cond Range has the choice of 2 class V remote controls (they allow deduction at 65), in the Base and Top version with weekly chronothermostat functions with up to 4 programmable periods with independent temperatures, in addition to the remote control of all the information of the boiler display. Product Guarantee: All products for sale on our site are new and packed. The guarantee on this item is 24 months from the date of purchase.
€885,00
You have seen 24 out of 131 products
