Product name VAILLANT ecoTEC PURE CONDENSING VMW 246/7-2 COMPLETE WITH FUME EXHAUST KIT - NEW ErP Technical features Heating efficiency class A Sanitary efficiency class A XL load profile Nominal thermal power in sanitary kW 28.0 DHW nominal heat input kW 7.8 - 24.8 Performance stars (Dir. 92/42CEE) ★★★★ NOx class 5 Nominal flow rate in heating (ΔT=20K) l/h 1033 Expansion vessel capacity l 8 Maximum operating overpressure bar 3 Domestic hot water production (ΔT = 30K) l/min 13.5 Domestic hot water comfort stars (prEN 13203) ★★ Power supply V/Hz 230/50 Total electric power W 100 Dimensions H x W x L: 720-335-440; 30.8Kg Sound power dB(A): 49 Degree of protection IP X4 D Power supply: METHANE General characteristics Vaillant condensing boiler With the strategic plan 20/20/20, Europe has the objective of producing 20% less CO2, using 20% more renewable energy and consuming 20% less primary energy. All this by 2020. To achieve these objectives, the EU has issued the ErP Directive (energy related products) which specifies the minimum eco-design requirements for equipment that uses energy, including energy efficiency. The world of heating will also be affected by this revolutionary change. In fact, from 2015 the energy efficiency of boilers will be based on new performance indexes that will take into account seasonal performance. Among the most significant changes to the new methodology for measuring seasonal efficiency are the introduction of different nominal temperatures, operation also at partial loads and in standby mode. The new methodology will make it possible to evaluate the performance of a boiler in real conditions, based on the level of efficiency calculated over an entire year. NEW EcoTEC PURE The easiest way to switch to Vaillant condenser. Vaillant DNA is synonymous with quality. Always. ecoTEC pure represents the solution that Vaillant offers to anyone who wants to switch to a Vaillant condensing boiler without worries. ecoTEC pure is really simple to install. It is equipped with vertical hydraulic connections that make replacement jobs simple, both for those who are abandoning a traditional boiler (atmo-turboBLOCK), and for those who choose Vaillant for the first time. All in full compliance with the characteristics that identify Vaillant products: the boiler is in fact in energy class A both in heating and in the production of hot water. Even the new ecoTEC pure design immediately recalls the quality and reliability that characterize the company's DNA; the lines are clean for this new indoor condensing boiler with standard measurements: 70cm high, 44 wide and 33 deep. ecoTEC pure heats the water and the rooms to give the right comfort in a convenient way. It is available with a single model in the power of 24kW. Comfort, savings, safety Instant hot water even for small requests High sanitary comfort Condensation with Vaillant DNA The most convenient solution The vertical hydraulic connections allow for carefree replacement Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€913,00
ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli condensing boiler Bluehelix Alpha 24C complete with methane or LPG fume exhaust kit cod. 0TPF2AWA Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Heating max / min heat input (Hs) kW 22.9 / 4.7 Max DHW heat input (Hi) kW 25 Max working pressure heating bar 3 Min. heating operating pressure bar 0.8 Heating expansion vessel capacity 8 litres Max DHW working pressure bar 9 Minimum DHW operating pressure bar 0.3 Sanitary flow rate ∆t 25°C l/min 14 Protection degree (IEC 60529) IP IPX4D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x250 Bluehelix Alpha .. More beautiful than "BEFORE" The new range of generators is equipped with the tested heat exchanger in stainless steel . Designed and built according to the new ErP directives for eco-compatible design and labelling, BLUEHELIX ALPHA is at the top of its category. TOP EFFICIENCY EVEN ON OLD SYSTEMS (REPLACEMENTS) mod. 24 C COMBINED (14 l/min at ∆t 25°C) The BLUEHELIX ALPHA thermal group exchanger (fig. A) compared with the more classic and widespread steel exchanger. This geometry allows the exchanger to operate almost at maximum design efficiency even in conditions of partial blockage, while with the same amount of deposits and sediments (e.g. due to installation on old systems) the exchanger in fig. B tends to block up much faster in the part in contact with the flame due to the reduced passage area of the fluid, in which a real barrier of deposits * is formed which hinder the heat exchange and reduce the efficiency beyond below the nominal values BLUEHELIX ALPHA FROM THE INSIDE EXCHANGER High flow single circuit stainless steel exchanger, resistant to clogging and easy to clean STEEL FRAME Made with high precision automated processes EXPANSION TANK 8 liter expansion tank placed on the side ELECTRIC PANEL FAN Offset fan, to facilitate maintenance of the primary exchanger without disassembly DOMESTIC HOT WATER EXCHANGER In stainless steel, with copper brazing CIRCULATOR High efficiency, for heating and exchange with the DHW circuit SEALED CHAMBER Removable steel panel to protect the combustion chamber with the function of a sealed chamber ELECTRICAL PANEL Large removable electrical panel to protect against any water damage that may occur during normal maintenance. Easy access to electrical connectors. THE ENGINE The tube that makes up the BLUEHELIX ALPHA exchanger is made of stainless steel, a material that allows for the creation of an extremely smooth surface, therefore less susceptible to encrusting agents and deposits. THE BOILER CONTROL The control box of BLUEHELIX ALPHA consists of an easy to use interface with backlit display. Using the buttons, it is possible to easily adjust the heating flow temperature, the domestic hot water setpoint, switch the generator on/off or activate the comfort function, monitoring the status of the boiler. The control panel is completed by a traditional pressure gauge which can check the system pressure at any time. MC2 The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). MGR Methane, LPG, Propane Ready Air The electronics control the flame ionization current in order to ensure optimal combustion as the air density or gas quality varies. The relationship between the air/gas ratio (λ) and the flame ionization signal is used to control the air-gas ratio itself and therefore the combustion. MC2 : Multi Combustion Control, the new combustion system with patented Gas-adaptive technology improves the adaptability of use as the conditions of the gas network vary (e.g. fluctuations or reduced pressures). Thanks to the new electronics supplied, the gas change operation is extremely simple. The MC2 combustion control performs constant monitoring of the quality of the combustion and by simply modifying a parameter on the electronic card (operation to be carried out only by qualified personnel) it is possible to operate the boiler on Natural Gas or LPG or Propane Air. It is therefore not necessary to purchase additional accessory kits. CONNECT New wireless remote control available as an accessory for home comfort management also from a smartphone using the connect app (iOS and Android). Maximizes room comfort with delivery temperature modulation through the Room Climatic Compensation (CCA) and External Climatic Compensation (CCE) functions via the external temperature detectable directly from the internet (or from an optional external probe). It improves the average seasonal efficiency in space heating by +4%. EASY MAINTENANCE Problem-free maintenance At the time of the first maintenance, the technician can appreciate the care with which every detail has been designed to facilitate his work. Thanks to the maximum accessibility of the main components, the BLUEHELIX ALPHA thermal group allows maintenance to be carried out with maximum precision and speed. Some examples: - The electrical box of the electronic card can be easily extracted from the chassis leaving free access to the internal parts. - Easy access to the burner unit by removing 4 screws and the quick coupling (clip) of the fan. - The exchanger with extra-large passages is designed to challenge the hardest waters and is easy to clean thanks to the non-collectorised single-pipe circuit. - The domestic hot water inlet filter can be extracted very easily directly from the inside without having to remove the boiler hydraulic connections. - Any disassembly and replacement of the plate heat exchanger takes place simply by removing the two Allen bolts accessible from the front SUN EASY FUNCTION BLUEHELIX ALPHA has been designed to be easily inserted into systems made with the latest technologies. The SUN EASY system makes use of electronics that simplify the combination with solar panels with both natural and forced circulation. By means of a sensor located on the DHW circuit, it continuously controls the temperature of the water preheated by the solar panels, foreseeing the ignition of the burner only if the latter drops below the level necessary to guarantee optimal comfort for the user. STOP AND GO FUNCTION With the use of sanitary taps with mixing, short or very short dispensing for quick rinses involves the start of the boiler ignition procedure which usually ends immediately. The continuation of these "false starts" can, in the long run, compromise the average life of the product. For this reason BLUEHELIX ALPHA provides an electronic parameter through which it is possible to delay burner ignition (Stop and Go) by activating it only in the face of actual withdrawals of domestic hot water. OUTDOOR INSTALLATION - ANTIFREEZE FUNCTION To make the most of the available space, the new BLUEHELIX ALPHA 24 - 28 C boiler can be installed recessed into the wall thanks to the special kit; for more critical installations, in completely uncovered places not protected from atmospheric agents, the "painted cabinet" kit is also available. In the event that the temperature in the boiler drops to 5°C, the burner automatically lights up and the circulator is activated in order to protect the appliance from damage caused by frost. This function is active with the boiler powered by the gas circuit and under electrical voltage. SANITARY ECO-COMFORT FUNCTION In ECO operation, the production of domestic hot water takes place according to traditional standards, allowing for energy savings during periods of non-use. In COMFORT mode, thanks to the particular heat exchanger temperature maintenance system, the delivery of domestic hot water becomes even faster and more comfortable. The efficiency and the load profiles according to the ErP directive are at the top of the category: mod. 24 C / A - XL. Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€653,00
THE BOILER IS BORN WITH METHANE. THEREFORE, YOU MUST REQUEST THE TRANSFORMATION KIT. FOR INFO, CONTACT THE AUTHORIZED AREA ASSISTANCE CENTER IN ADVANCE Technical features Model : ecoTEC Intro VMW 24/28 AS/1-1 Article code : 0010026088 Power supply: methane Performance Heating power : 6.9 ~ 23.9 kW Nominal heat input in DHW : 6.9 ~ 28.0 kW Energy efficiency class in heating: A Sanitary energy efficiency class: A Sanitary load profile : XL NOx class : 6 Efficiency at 30% : 108.2% Domestic hot water production (ΔT = 30K): 13.4 l/min Domestic hot water temperature adjustment: 35°C ~ 60°C Modulation : 1:4 Expansion vessel pre-charge pressure: 0.75 bar Minimum water pressure: 0.3 bar Total electric power: 90 W Expansion vessel capacity: 8 litres Dimensions and weight Dimensions (HxWxD): 626x400x270 mm Weight : 25.6Kg Warranty extension to 7 years ecoTEC Intro VMW wall-mounted condensing boiler The most compact and lightest, now also for outdoor use The new ecoTEC intro VMW condensing boilers (for heating and domestic hot water production) are available in 24 and 28 kW power ratings, increasing the range of product choices within the consolidated range of Vaillant condensing boilers. In fact, this product gives new users the opportunity to approach the world of condensing boilers offered by Vaillant, without incurring excessive costs for replacing the old boiler. ecoTEC intro maintains the focus on energy saving by mounting a high-efficiency modulating pump that minimizes annual electricity consumption , with a consequent positive impact on bills. Also with regard to gas savings, Vaillant offers the new combustion technology , called fan push, where it is the fan which, thanks to the different levels of pressure exerted on the gas valve, guarantees the right ratio between combustion air and gas. The ecoTEC intro case is simple and essential, the dimensions appear to be extremely small which however do not affect or reduce the quality and efficiency of the product, guaranteed by Vaillant. The front panel introduces an innovative , extremely simple touch screen interface with 6 keys, black background display and 2 white digits with intermittent switching on. An additional e-bus connector has been added to the bottom of the boiler which allows connection to Vaillant temperature control units and thermostats. These wall mounted boilers are very simple to install thanks to their dimensions (62.6cm high, 40cm wide and 27cm deep) and low weight (about 26kg): these features make them ideal whenever replacement is required. All the components that are present in the product comply with the ErP energy efficiency regulations, a guideline also embraced by Vaillant, as a brand sensitive to environmental issues. This is all that the new ecoTEC intro can offer, in addition to a competitive price which does not affect performance. First ignition free Vaillant guarantees, through the work of its technicians, the free first ignition service on all wall-mounted condensing boilers. ecoTEC wall mounted boiler intro Electricity consumption in standby less than 2W Innovative touch screen display Sanitary comfort even with low flow rates Low installation costs Small size Exchanger in stainless steel Pneumatic combustion system with complete pre-mixing Vertical hydraulic connections 1:4 modulation Instant DHW production 8 liter expansion vessel Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€845,00
ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT BAXI ASSISTANCE IN ADVANCE Baxi Luna Classic 28 kW low NOx condensing boiler complete with methane or LPG fume exhaust kit New optional Wi-Fi Technical features Sanitary nominal thermal power kW 28.9 Heating rated thermal power kW 24.7 Useful thermal power at thermal power nom. and high temp. regime* P4 kW 24 XL load profile Seasonal space heating energy efficiency class A Water heating energy efficiency class A Seasonal space heating energy efficiency ?s % 94 Minimum operating temperature °C -5 Heating expansion vessel capacity l 7 Sanitary water production ?T 25°C (1) l/min 16.1 Dimensions (hxwxd) mm 700 x 395 x 285; 30 Degree of protection IPX5D CLASSIC MOON The new Luna Classic is the ideal product for apartments or small houses. Its compact dimensions (700x395x285 mm) ne allow installation in confined spaces such as kitchen wall units or in the laundry room. Excellent value for money, simple and intuitive management. The heart of the Luna Classic is the new electronic platform: this revolutionary system replaces the functions of the historical Luna models, raising the quality of the product to a new level. Great attention has been paid to meeting the needs of the end user. System customization and optimization are possible without compromising ease of use. The Luna Classic range includes 2 models for heating and the instantaneous production of domestic hot water, Luna Classic 24 and Luna Classic 28 User Interface Luna Classic Control Panel Renewed interface with: Backlit menu with icons; Simple settings to adjust the heating and domestic hot water temperature via two dedicated knobs; 4 buttons with dedicated functions: menu, confirm, back and reset. 2 functions for perfect water temperature Domestic hot water management can be enhanced and improved by activating two dedicated functions: relaxation function It is a pre-heating function which keeps the domestic hot water at the desired temperature for a pre-set period of time, or for 30 minutes after selecting the chosen temperature. Boost function Activates the boiler at maximum power for faster delivery of hot water. Baxi MaGO Luna Classic can be connected directly to the Baxi Mago, the modulating chronothermostat with integrated wi-fi that allows you to manage home comfort directly from an App. By downloading the dedicated App onto your smartphone, it will be possible to connect to one or more homes to control the temperature, manage the programming, display the consumption graph, read any messages error, set vacation mode, etc. The combination of the boiler with the Baxi Mago A+ kit increases its energy efficiency, raising it to class A+ Specifications: Operation with a mixture composed of up to 20% hydrogen New single coil stainless steel heat exchanger, featuring sections with large water passages for greater seasonal thermal efficiency Seasonal energy efficiency of 94% thanks to the advanced technology applied Renewed interface with backlit display Easy replacement of conventional boilers thanks to central flue gas outlet Modulation range 1:5 greater efficiency and silence Ø80 double exhaust STANDARD Connection to Ø50 mm rigid and flexible waste pipe: solutions for the rehabilitation of flues total length (exhaust + intake) 40 meters Connection to pressurized collective flues Boilers running on methane that can be converted to LPG and propane by means of a specific regulation (conversion kit not necessary) Compact dimensions: 700x395x285 mm Class A+ for Luna Classic 24/28 models with Baxi Mago and external probe (as accessories) New hydraulic group that guarantees maximum levels of performance and durability over time Optimal insulation for silent operation Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€790,00 - €829,00
ATTENTION Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits. For info, contact the local authorized assistance center in advance Ferroli BLUEHELIX PRO RRT 28 C methane or LPG condensing boiler Complete with Lox NOx Fume Exhaust Kit - NEW Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Thermal power 80°C-60°C Max Heating: 24.0 / 4.9 kW Thermal power 50°C-30°C Max Sanitary: 26.0 / 5.4 kw Useful thermal efficiency 30%: 109.7 Max working pressure heating bar 3 NOx class 6 Sanitary flow rate ∆t 25°C 15.8 Protection degree (IEC 60529) IP X5D Supply voltage V/Hz 230V / 50Hz Dimensions HxWxD mm 700x420x250 BLUEHELIX PRO RRT The quality of the BLUEHELIX line is unquestionable, and Ferroli is ready to put it to the test by offering its customers extended warranty coverage which also ensures periodic maintenance and statutory checks > STRONG POINTS: - With attention to aesthetics and silence, it continues the tradition of appreciation of the previous "Bluehelix Pro" series - DUAL STAINLESS STEEL exchanger : boiler with primary exchanger for heating and domestic hot water in very thick stainless steel integrated in a single component (DUAL). High efficiency even during DHW operation (94%). - Increased hydraulic passages of the exchanger both on the heating circuit and on the DHW circuit. - : in combination with the modulating remote control and the external probe (optional) it reaches the upper efficiency class A+ (scale from G to A+++) - MC2 : Multi Combustion Control, new combustion system with patented gas-adaptive technology of industrial origin for better adaptability of use to varying conditions of the gas network (e.g. fluctuations or reduced pressures) - MGR: Natural gas, LPG, Propane air Ready through a simple configuration the boiler is able to operate on natural gas, LPG and propane air without the use of additional conversion kits - Exclusive exchanger-burner system with self-cooled door: simplifies maintenance and reduces its cost thanks to fewer parts to replace - Hydraulic connections covered by the boiler casing - Large backlit multifunction graphic display for easy and correct setting of the parameters - Standard by-pass > BENEFITS OF bluehelix PRO RRT C: - Particularly suitable for operation in flues that require "heavy" ducting thanks to the approval for operation with 50mm diameter flue pipes - FPS: Smoke Protection System. The flue clapet valve inserted as standard on the boiler allows easy connection to pressurized collective flue systems (e.g. in renovations), in accordance with the UNI 7129 standard - Designed to simplify and facilitate normal maintenance and cleaning operations - Predisposition for solar systems: prearranged for the production of domestic hot water combined with solar panel systems - STOP AND GO: it is possible to delay the ignition of the burner by activating it only in the face of real withdrawals of domestic hot water - 3-star certified comfort in sanitary manufacturing according to EN 13203 - Minimum polluting emissions (class 6 according to EN 15502-1) - Sliding temperature operation via optional external probe - Low consumption modulating heating pump (ErP Ready - Class A) - Digital flame control with three re-ignition attempts in the event of malfunction due to lack of flame detection (methane model) - Place of installation: also for outdoors in a partially protected place up to -5°C as standard and up to -15°C with the help of the optional antifreeze heater kit - Free methane/LPG/propaneted air transformation when checking the product and activating the warranty, to be requested from the Authorized Assistance Center Product Warranty All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€780,00€760,00
ARISTON HS PREMIUM 30 EU CONDENSING BOILER COMPLETE WITH METHANE FUME EXHAUST KIT - ErP Technical features Product code: 3300760 Energy label specifications according to the European ErP directive Energy label specifications according to the European ErP directive Class A heating energy efficiency Sanitary energy efficiency profile XL Class A Characteristics of heating/DHW operation: Nominal heat input in heating max/min: Kw 29.0/6.0 Max/min nominal heat input in domestic hot water: Kw 29.0/6.0 Useful thermal power in heating: max/min: Kw 28.4/5.8 Efficiency at nominal heat input (60/80°C): 97.8% Efficiency at nominal heat input (30/50°C): 104.0% Efficiency at 30% at 30°C: 108.0% Max/min heating temperature (high temperatures): 82/35°C Max/min heating temperature (low temp.): 45/25°C Max/min DHW temperature: 60/36 °C Sanitary water production (DT=25°C): lt./min. 16.3 Specific flow rate (first 10' with DT=30°C): lt./min. 11.6 Total absorbed electric power W 82 Degrees of protection of the electrical system IP X5D Dimensions (HxWxD) mm 745 x 400 x 319 Power supply: METHANE Ariston condensing boilers 1 condensing boiler = -737kg CO2/year 1 condensing boiler = 60 more trees Together with the heat, a traditional boiler also produces water in the vapor state, usually evacuated through the exhaust fumes. Normal boilers, since they do not treat these fumes before releasing them into the environment, therefore have a thermal efficiency based exclusively on the lower calorific value. The water vapor is not recovered in any way, thus dispersing part of the energy produced during combustion. Condensation is the physical process which, inside the boiler, transforms the water again from the vapor state to the liquid one. Consistent convenience The new products, using condensing technology, eliminate waste with great energy and economic savings. Thanks to the savings in the bill, less than three years are enough to amortize the higher cost of a condensing boiler. After that, the lower consumption translates into a real gain. Imagine what a reduced bill of up to 35% every year, for many years, means for your economies... Zero waste, only benefits Today Ariston combines energy savings with tax savings, offering a great opportunity to those who have chosen to replace the old boiler with a condensing one. In fact, the Finance law provides for specific tax incentives in favor of taxpayers. HS Premium Performance ★★★★ NOx class 5 LCD display. Continuous modulation high efficiency circulator. Modulation ratio 1:4. Arrangement for integration with system configuration through the new Buss Bridgenet® communication protocol Arrangement for multi-zone and multi-temperature thermoregulation (with Sensys). Arrangement for solar system management. Aluminum alloy primary exchanger Sanitary plate heat exchanger. Self-diagnosis system by codes. Increased expansion tank lt.8. Cold water inlet and heating return filters. Protection against freezing, limescale and circulator blocking. Operation only with methane gas Product Guarantee All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€834,00
ATTENTION ! In case of immediate lack of availability, the product will be ordered and shipped within 10 working days Technical features Model: D2CND024A0AA Heating Efficiency class (55°C) : A Fireplace power (Qn) : 2.9 - 23.5 kW Nominal heating power (80°/60 °C): 2.8 - 22.8 kW Nominal heating power (50ç/30 °C) : 3.1 - 24.0 kW Heating efficiency : Up to 108.7% Modulation range : 1:8 Expansion vessel volume: 8 litres Domestic hot water Efficiency class : A Withdrawal profile : XL Temperature range : 35°C ~ 60°C Withdrawal in continuous service (∆T=30°C): 11.3 l/min Withdrawal in continuous service (∆T=25°C): 13.6 l/min Pressure of the water network: 0.5 ~ 10 Bar Technical data Power supply (V,Hz, Ø) : 220~240/50/1 Electric Power Input: 3.5~86W Water content : 1.31 litres Sound power : 39 dB(A) Sound pressure : 49 dB(A) NOx class : 6 Exhaust gas temperature (G20) : 77° C Electrical protection class : IP X5D Installation data Flue diameter: 60/100 mm Maximum length for flue system DN 60/100 : 12.5 m Maximum length for flue system DN 80/125 : 42.8 m Maximum length for flue system DN 80/80 : 125 m Dimensions and weight Dimensions (HxLxD): 590x400x256 mm Weight : 27Kg Simply Serene Guarantee To guarantee you maximum serenity, DAIKIN has studied "SIMPLY SERENIOUS", an extension of the guarantee up to the 5th year of life of your product, which provides for the subscription of a Scheduled Maintenance Plan with specialized Daikin technicians Ultra-compact Daikin D2C condensing boilers for heating and DHW production Why choose a condensing boiler? Daikin condensing boilers are a good solution for those wishing to replace an existing boiler with a more efficient alternative, saving on costs. Our portfolio includes boilers for every need, from the D2C and Full condens and Full Condens TOP wall-hung boilers, to the GCU boiler with built-in thermal storage, to the A2 floor-standing diesel boiler Thanks to the special Daikin-patented exchanger, the D2CND boiler obtains high specific power and high partialization to guarantee comfort and efficiency in any operating mode and in minimum encumbrance. The D2T version, heating only, integrates a diverter valve and can be connected directly to a storage tank for the production of domestic hot water. Ultra-compact and elegant technology The beautifully compact boiler The new D2C condensing boilers are 100% Daikin design. The ultra-compact dimensions make them suitable for even the smallest apartments, where every centimeter saved is space gained A boiler for every need D2C boilers are available in 3 combi versions 24, 28 and 35 kW for heating and instant domestic hot water production. A wide range of heating-only boilers is also available, the D2T, in 5 sizes, from 12 to 35 kW, which can be combined with a storage tank for the production of domestic hot water. You can install them virtually anywhere thanks to their compact size and minimal installation space required. Thanks to the IPX5D degree of electrical protection and the antifreeze kit, they can also be installed outdoors. Do you want to have your heating system under control even when you are not at home? Pair the Lan Adapter to control via APP ! Efficiency and respect for the environment The combustion system with regulation via Lambda Gx probe automatically adapts to the quality of the gas used, methane or LPG, always guaranteeing clean combustion and minimum polluting emissions . Maximum comfort Thanks to a high modulation ratio, up to 1:8 , the output power is automatically varied to always adapt, instant by instant, to the real need of the house in which it is installed. Endless showers? Domestic hot water will no longer be a problem with the D2C boiler with a DHW flow rate of up to 19 l/min in the 35 kW version Cutting-edge technology combines with an attractive and user-friendly user interface Daikin Eye An elegant luminous eye which, thanks to a multi-chromatic LED, signals the operating status of the appliance. In the event of a fault, the LED turns red and the error code is displayed. The easiest way to interact with your boiler! Daikin Heating Online Controller The heating system is always under control, wherever you are! Thanks to the Daikin Heating Online Controller application you can now control and monitor your boiler from the comfort of your smartphone in a simple and intuitive way Monitor The status of your heating system The ambient temperature in your home Energy consumption graphs. Plan The temperature of your home and the operation of the boiler with up to 6 actions per day for 7 days Vacation mode Check it out The operating mode and the set room temperature The system and the production of domestic hot water By integrating third-party products and services through IFTTT services (if this then that) Changing your old boiler has never been easier! Thanks to its small size and IPX5D degree of protection, Daikin D2C can be installed practically anywhere. Its ultra-compact dimensions make it suitable for even the smallest apartments, where every centimeter saved is space gained and its elegant shapes look good in the kitchen. A distinctive element of the 100% Daikin design is also the Daikin Eye: an elegant luminous eye which, thanks to a multi-chromatic LED, signals the operating status of the appliance. Daikin D2C contains the best of condensing technology. The SCOT combustion regulation system automatically adapts to the quality of the gas used, methane or LPG, always guaranteeing clean combustion and minimum polluting emissions. Dimensions and weight reduced to a minimum are possible thanks to the innovative Daikin patented high specific capacity air/fume exchanger body. Heart of the new D2C boiler, it has been designed to obtain the highest thermal power in the smallest size. Functions Eco Mode Return temperature control to optimize condensation Warm start DHW exchanger already heated and ready for use thanks to the memorization of the habits which allows to anticipate the request for domestic hot water Solar connection If the water entering the boiler has been preheated by the solar system, the burner does not ignite, for optimal integration of the solar source Exclusive initiative for Daikin customers On the occasion of the launch of the new Daikin D2C, starting from 1 March 2017 Daikin is giving away the activation cost of Simply Serene. The offer is valid for all those who will purchase a Daikin boiler of any type and who already own a Daikin mono split or multisplit. All the details on daikin.it. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€995,00
ATTENTION THE BOILER IS SUPPLIED WITH METHANE. LPG OPERATION THROUGH ADJUSTMENT BY AN AUTHORIZED SERVICE CENTER. FOR INFO, CONTACT THE AREA HERMANN ASSISTANCE IN ADVANCE Hermann Saunier Duval Combitek 24-AS/1 low NOx gas boiler complete with methane or LPG fume exhaust kit - News Select the smoke kit in the drop-down menu! Product specifications Condensing Type of installation Wall Type of fuel Methane Manufacturer's warranty (in years) 2 Energy class in heating A Domestic hot water energy class A Rated power (in kW) 24 Instant hot water production Modulation range 1:5 Integrated thermostat No Ideal for N° floors 1 Net weight (in kg) 25.6 Flow (in l/min) 14 Packed product: width (in cm) 36 Packed product: depth (in cm) 49 Packed product: height (in cm) 89 Packed product: weight (in kg) 30.2 COMBITEK The optimal solution for heating and domestic hot water preparation . Excellent value for money, both for new builds and replacements It can be retrofitted into existing heating and hot water supply systems The project has been developed to offer the optimal solution in terms of price , performance and quality . Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€683,00
Caratteristiche tecniche Modello : Residence IN 25 KIS Codice prodotto : 20189650 Potenza nominale : 19,0 kW Alimentazione : Metano/gpl Efficienza energetica Classe di efficienza energetica stagionale del riscaldamento : A Classe di efficienza energetica del sanitario : A Efficienza energetica stagionale del riscaldamento : 93% Consumo energetico annuo : 42 GJ Potenza termica utile Potenza termica nominale e a regime di alta temperatura : 19,4 kW Potenza termica nominale e a regime di bassa temperatura : 6,5 kW Efficienza utile Alla potenza termica nominale e a regime di alta temperatura : 87,3 % Al 30% potenza termica nominale e a regime di bassa temperatura : 98,5 % Consumi elettrici ausiliari A pieno carico : 32,0 W A carico parziale : 12,0 W In modalità Stand-by : 3,0 W Performance in riscaldamento Portata termica : 3,95 ~ 25 kW Pressione massima : 3 bar Temperatura massima : 90° C Performance in sanitario Portata ACS minima : 2 l/min Pressione massima : 8 bar Produzione ACS : 10,2 ~ 11,9 ~ 14,3 kW Dati installativi Diametro tubo entrata / uscita riscaldamento : 3/4" Diametro tubo entrata / uscita sanitario : 1/2" Dimensioni e peso Dimensioni (AxLxP) : 740x420x249 mm Peso : 31,0 Kg Caldaia murale a condensazione Riello RESIDENCE IN La soluzione efficiente, dove lo spazio fa la differenza Residence In è la soluzione Riello pensata per le esigenze installative in cui lo spazio fa la differenza e per un comfort senza compromessi. Residence In si distingue per compattezza, flessibilità applicativa e ampia disponibilità di accessori che garantiscono la compatibilità e retrocompatibilità anche nei box Riello più piccoli. Lo scambiatore primario, interamente realizzato in acciaio inox e con accessibilità frontale alla camera di combustione, e lo scambiatore a piastre ottimizzato assicurano la massima efficienza e affidabilità nel tempo e garantiscono un comfort elevato, sia in riscaldamento che in sanitario Con RESIDENCE IN, Riello continua il percorso di rinnovamento della propria offerta murale in chiave eco-compatibile. L’ampio range di modulazione 1 : 8, le bassissime emissioni di NOx, che posizionano la gamma in Classe 6 (la migliore secondo gli standard europei), e la predisposizione per il funzionamento con miscele di gas naturale e idrogeno – fino a un massimo del 20% - sono solo alcune tra le caratteristiche che qualificano RESIDENCE IN come la caldaia ideale per un’installazione di valore nel tempo, dal minimo impatto ambientale ed estetico. Installazione universale Massima flessibilità installativa sia all’interno, all’esterno (in luogo parzialmente protetto) e a incasso in box Stabilità di acqua calda sanitaria Acqua calda senza oscillazioni di temperatura, per un comfort ottimale durante i prelievi Interfaccia digitale Interfaccia dal design moderno, che si distingue per l’intuitività di utilizzo, comunicando con l’utente per mezzo di icone e testi scorrevoli. Basse emissioni La migliore in termini di rispetto ambientale a livello europeo Compattezza e flessibilità per un'installabilità universale RESIDENCE IN è la soluzione ideale per la sostituzione, oltre che per la nuova edilizia. Le dimensioni ridotte del prodotto, unitamente alla disponibilità di una gamma articolata di kit accessori per ogni tipo di applicazione, facilitano e velocizzano l’installazione, anche in piccoli box pre-esistenti. RESIDENCE IN, come suggerisce il nome, è la nuova caldaia Riello pensata in primis per l’installazione a incasso in box. Grazie alle ridotte dimensioni e alla disponibilità di una gamma dedicata di kit accessori, RESIDENCE IN è compatibile e retrocompatibile con le varie tipologie di box Riello. La nuova soluzione Riello, in caso di sostituzione di un modello a incasso, assicura all’utente un notevole risparmio, evitandogli sia l’acquisto di un nuovo box, che eventuali spese murarie per adeguare lo spazio della nicchia. Inoltre, gli attacchi idraulici con sequenza Riello rendono la sostituzione con le vecchie caldaie ancor più facile e immediata. L’installabilità a incasso è un plus anche per la nuova edilizia, permettendo di risparmiare spazio sempre più prezioso all’interno dell’abitazione e riducendo al minimo l’impatto estetico in facciata. Adatta per l'esterno RESIDENCE IN, grazie al grado di protezione IPX5D e al kit accessorio antigelo fino a -15°C, può essere installata anche all’esterno dell’abitazione, in luogo parzialmente protetto. Design moderno e utilizzo intuitivo RESIDENCE IN è dotata di un pannello di controllo dalle linee razionali e moderne, che si distingue per la semplicità di utilizzo. Attraverso il display LCD retroilluminato, che comunica con l’utente mediante icone e testi scorrevoli, è possibile accedere facilmente a tutte le funzioni di RESIDENCE IN. Un cuore d'acciaio per la massima efficienza RESIDENCE IN è dotata di un nuovo scambiatore primario in acciaio INOX, con tubo liscio ad elevata sezione, in grado di assicurare la migliore efficienza e pulizia nel tempo. L’acciaio INOX, oltre all’elevata resistenza all’azione corrosiva della condensa acida, previene la formazione interna di ossidi e di altri fenomeni elettrochimici tipici delle installazioni in vecchi impianti. La geometria a spira unica avvolta (circuito idraulico in serie) assicura una portata costante in tutte le sezioni dello scambiatore e previene intrinsecamente fenomeni di intasamento. L’accesso frontale agevola le operazioni periodiche di manutenzione e pulizia della camera di combustione. Comfort sanitario elevato Grazie al nuovo scambiatore a piastre high performance, RESIDENCE IN offre un elevato comfort in sanitario, con disponibilità di acqua calda in tempi brevi e un’ottima stabilità della temperatura di erogazione. Funzionamento silenzioso RESIDENCE IN, distinguendosi per la silenziosità operativa, rappresenta la scelta ottimale anche per l’installazione in locali non tecnici, ad esempio in caso di sostituzione in una cucina. Garanzia prodotto : Tutti i prodotti in vendita sul nostro sito sono nuovi ed imballati. La garanzia su questo articolo è 24 mesi dalla data dell'acquisto.
€1.140,00
Condensing boiler Immergas VICTRIX TERA 24 V2 low nox methane complete with flue kit 1 036051 General characteristics Model: VICTRIX TERA 24 V2 Code: 1.036051 EAN: 8015065134824 Power supply: methane Heating Energy Efficiency Class: A Sanitary Energy Efficiency Class: A Sanitary nominal thermal power (useful): 28.0 kW Heating nominal heat output (useful): 24.0 kW Technical data sheet (Method Directive 92/42/EEC) Burner type: Blown air Power at rated load: 24.0 kW Power at 30% of nominal load: 7.2 kW (at 50/30 °C) Efficiency at nominal load: 106.5 Efficiency at 30% of nominal load: 107.5 (at 80/60 °C) Efficiency at nominal load: 97.8 Efficiency at 30% of nominal load: 96.8 Electric auxiliaries at rated load: 41 W at intermediate load: 60 W at zero load: 2 W Operating temperatures Average temperature: 50°C Return temperature: 40°C DHW temperature: 55°C With DHW priority: yes TEST conditions at nominal load Average generator temperature: 70 °C Yield correction factor: 0.2 at intermediate load Average generator temperature: 70 °C Yield correction factor: 0.2 at zero load Power lost: 54.4W Mantle loss fraction: 0.36 Dimensions Legend: V - Electrical connection G - Gas supply AC - Domestic hot water outlet ACV - Kit domestic hot water inlet solar valve (optional) AF - Domestic hot water inlet SC - Condensate drain (internal diameter minimum Ø 13 mm) M - System delivery R - System return Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase.
€925,00
Hermann Saunier Duval condensing boiler SEMIATEK CONDENS 28-AS/1 28 kW Methane Complete with Smoke Kit - New Select the smoke kit in the drop-down menu! Technical features Model : Semiatek Condens Power : 28 kW Methane gas Heating efficiency class: A Sanitary efficiency class: A Sanitary load profile XL Fireplace flow rate Qmin/max - 75/55°C : 7.2 - 24.5 kW Rated power Pmin/max - 75/55°C : 6.9 - 23.9 kW Rated power Pmin/max - 50/30°C : 7.7 - 25.9 kW Efficiency Pmax - 80/60°C - 50/30°C : 97.6 / 105.9 % Efficiency P30% - 40/30°C : -/-/108,1 % Min/max flow temp. : 30 - 75 Min/max boiler operating pressure: 0.3/3 bar Heating expansion vessel - Capacity/pre-charge : 8/0.75 l/bar Domestic hot water production type: Instantaneous ACS quality classification (EN 13203-1) : Capacity at the hearth min/max - 60°C : 8.0 - 31.1 kW Rated power min/max - 60°C : 7.2 - 28.0 kW Continuous flow rate (∆T= 25K) : 16.1 l/min Specific flow rate (∆T = 30K) (EN13203) : 13.4 l/min Peak flow rate in 10 minutes (∆T = 30K) : 134 l/10 min Min/max DHW temperature : 35 - 55 °C Gas category : II 2H 3P Absorption - Peak/Pmax/Pmin/Stand-by : - / 90 / - / 1,7 W Weight : 26.5Kg Semiatek Condens 28 kw The optimal solution for heating and domestic hot water preparation. Excellent value for money, both for new builds and replacements It can be retrofitted into existing heating and hot water supply systems Heat exchanger in stainless steel 3 year guarantee The SemiaTek Condens boiler is available in 24 and 28 kW methane power. The most important novelty concerns the renewed primary exchanger , the old one in Al-Si has been replaced by the one in stainless steel which, through a simple adjustment of the gas valve, also allows operation with propane. Innovation also from the point of view of combustion : complete premixing with new fan-push technology where the fan in the new position upstream of the burner guarantees the right ratio between air and gas by applying a proportional pressure value which guarantees the opening of the gas valve without waste. The project has been developed to offer the optimal solution in terms of price , performance and quality . SemiaTek Condens also features a new design of the ultra-compact hydraulic block with new location of the key components, while still maintaining a good level of efficiency, performance and adequate comfort in both heating and domestic hot water production. Characteristics The new design of SemiaTek Condens offers an innovative touch screen interface of extreme simplicity with 6 keys, display with black background and 2 white digits with intermittent ignition, the indication of the boiler status is defined by the intermittent ignition of the icon selected. SemiaTek Condens is compatible with all Hermann Saunier Duval components and accessories already on the market. SemiaTek Condens can also be combined with the MiGo WiFi control unit. The wall-mounted boiler is ready to be managed remotely simply with a smartphone. Ease of installation SemiaTek Condens is very simple to install thanks to its small size - 62.6cm high, 40cm wide and 27cm deep - and low weight. Even the vertical hydraulic connections have been designed to facilitate and speed up installation. For these reasons, it is the ideal solution for replacing old systems. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€844,00
NB: IN CASE OF ABSENCE OF THE PRODUCT WE WILL SEND THE SIMILAR MODEL THEMATEK CONDENS Gas Boiler Hermann Saunier Duval SEMIATEK CONDENS 24 AS/1 kW Methane Complete with Smoke Kit - New Select the smoke kit in the drop-down menu! Technical features Model : Semiatek Condens Power : 24 kW Methane gas Heating efficiency class: A Sanitary efficiency class: A Sanitary load profile XL Heating features Rated power Pmin/max - 80/60°C kW 6.0 - 18.3 Efficiency Pmax - 80/60°C - 50/30 °C % 97.2 - 106.4 Sanitary features Rated power min/max - 60°C kW 6.2 - 24.0 Specific flow rate (∆T = 30K) (EN13203) l/min 11.5 generals NOx class - 6 Electrical protection IPX - 5 Absorption - Stand-by / Pmax W 1.7 - 90 Dimensions (HxWxD) mm 626x400x270 Semiatek Condens The optimal solution for heating and domestic hot water preparation. Excellent value for money, both for new builds and replacements It can be retrofitted into existing heating and hot water supply systems Heat exchanger in stainless steel 3 year guarantee The SemiaTek Condens boiler is available in 24 and 28 kW methane power. The most important novelty concerns the renewed primary exchanger , the old one in Al-Si has been replaced by the one in stainless steel which, through a simple adjustment of the gas valve, also allows operation with propane. Innovation also from the point of view of combustion : complete premixing with new fan-push technology where the fan in the new position upstream of the burner guarantees the right ratio between air and gas by applying a proportional pressure value which guarantees the opening of the gas valve without waste. The project has been developed to offer the optimal solution in terms of price , performance and quality . SemiaTek Condens also features a new design of the ultra-compact hydraulic block with new location of the key components, while still maintaining a good level of efficiency, performance and adequate comfort in both heating and domestic hot water production. Characteristics The new design of SemiaTek Condens offers an innovative touch screen interface of extreme simplicity with 6 keys, display with black background and 2 white digits with intermittent ignition, the indication of the boiler status is defined by the intermittent ignition of the icon selected. SemiaTek Condens is compatible with all Hermann Saunier Duval components and accessories already on the market. SemiaTek Condens can also be combined with the MiGo WiFi control unit. The wall-mounted boiler is ready to be managed remotely simply with a smartphone. Ease of installation SemiaTek Condens is very simple to install thanks to its small size - 62.6cm high, 40cm wide and 27cm deep - and low weight. Even the vertical hydraulic connections have been designed to facilitate and speed up installation. For these reasons, it is the ideal solution for replacing old systems. Product Guarantee: All products for sale on our site are new and packed. The warranty on this item is 24 months from the date of purchase
€708,00
You have seen 24 out of 706 products
